ATMEL ATA5570 Multifunctional 330-bit read/write rf sensor identification ic Datasheet

Features
•
•
•
•
•
•
•
•
Contactless Read/Write Data Transmission
Sensor Input RS > 100 kΩ (Typical) => Data Stream Inverted
Radio Frequency fRF from 100 kHz to 150 kHz
e5550 Binary Compatible or ATA5570 Extended Mode
Small Size, Configurable for ISO/IEC 11784/785 Compatibility
7 x 32-bit EEPROM Data Memory Including 32-bit Password
Separate 64-bit Memory for Traceability Data
32-bit Configuration Register in EEPROM to Setup
– Data Rate
• RF/2 to RF/128, Binary Selectable or
• Fixed e5550 Data Rates
– Modulation/Coding
• FSK, PSK, Manchester, Bi-phase, NRZ
– Other Options
• Password Mode
• Maximum Block Feature
• Answer-On-Request (AOR) Mode
• Inverse Data Output
• Direct Access Mode
• Sequence Terminator(s)
• Write Protection (Through Lock-bit per Block)
• Fast Write Method (5 Kbps versus 2 Kbps)
• OTP Functionality
• POR Delay up to 67 ms
Multifunctional
330-bit
Read/Write RF
Sensor
Identification IC
ATA5570
Preliminary
1. Description
The ATA5570 is a contactless R/W IDentification IC (IDIC®) for applications in the
125 kHz frequency range. A single coil, connected to the chip, serves as the IC's
power supply and bi-directional communication interface. The antenna and chip
together form a transponder or tag.
The on-chip 330-bit EEPROM (10 blocks, 33 bits each) can be read and written blockwise from a reader. Block 0 is reserved for setting the operation modes of the
ATA5570 tag. Block 7 may contain a password to prevent unauthorized writing.
Data is transmitted from the IDIC using load modulation. This is achieved by damping
the RF field with a resistive load between the two terminals COIL1 and COIL2. The IC
receives and decodes 100% amplitude-modulated (OOK) pulse-interval-encoded bit
streams from the base station or reader.
Rev. 4863A–RFID–07/05
2. System Block Diagram
Figure 2-1.
RFID System Using ATA5570 Tag
Reader
Baseor
station
Base station
Coil Interface
Power
Data
Controller
Transponder
Memory
ATA5570
3. Pin Configuration
Figure 3-1.
Pinning SO8
NC
COIL1
NC
SENS
Table 3-1.
2
1
2
3
4
8
7
6
5
NC
COIL2
NC
VSS
Pin Description
Pin
Symbol
Function
1
NC
Not connected
2
COIL1
Antenna pin 1
3
NC
Not connected
4
SENS
5
VSS
Sensor input
Ground
6
NC
Not connected
7
COIL2
Antenna pin 2
8
NC
Not connected
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
4. ATA5570 – Building Blocks
Figure 4-1.
Block Diagram
RS
VSS
SENS
POR
CR
COIL2
4.1
Write
decoder
LR
Mode register
Memory
(264 bit
EEPROM)
Controller
Bit-rate
generator
COIL1
Analog front end
Modulator
Input register
Test logic
HV generator
Analog Front End (AFE)
The AFE includes all circuits which are directly connected to the coil. It generates the IC’s power
supply and handles the bi-directional data communication with the reader. It consists of the following blocks:
• Rectifier to generate a DC supply voltage from the AC coil voltage
• Clock extractor
• Switchable load between COIL1 and COIL2 for data transmission from tag to the reader
• Field gap detector for data transmission from the base station to the tag
• ESD protection circuitry
4.2
Data-rate Generator
The data rate is binary programmable to operate at any data rate between RF/2 and RF/128 or
equal to any of the fixed e5550/e5551 and T5554 bit rates (RF/8, RF/16, RF/32, RF/40, RF/50,
RF/64, RF/100 and RF/128).
4.3
Write Decoder
This function decodes the write gaps and verifies the validity of the data stream according to the
Atmel e555x write method (pulse interval encoding).
3
4863A–RFID–07/05
4.4
HV Generator
This on-chip charge-pump circuit generates the high voltage required for programming of the
EEPROM.
4.5
DC Supply
Power is externally supplied to the IDIC via the two coil connections. The IC rectifies and regulates this RF source and uses it to generate its supply voltage.
4.6
Power-On Reset (POR)
This circuit delays the IDIC functionality until an acceptable voltage threshold has been reached.
4.7
Clock Extraction
The clock extraction circuit uses the external RF signal as its internal clock source.
4.8
Controller
The control-logic module executes the following functions:
• Load-mode register with configuration data from EEPROM block 0 after power-on and also
during reading
• Control memory access (read, write)
• Handle write data transmission and write error modes
• The first two bits of the reader-to-tag data stream are the opcode, e.g., write, direct access or
reset
• In password mode, the 32 bits received after the opcode are compared with the password
stored in memory block 7
4.9
Mode Register
The mode register stores the configuration data from the EEPROM block 0. It is continually
refreshed at the start of every block read and (re-)loaded after any POR event or reset command. On delivery, the mode register is preprogrammed with the value 0014 8000h which
corresponds to continuous read of block 0, Manchester coded, RF/64.
4
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
1
0
0
0
9 10 11 12
13 14 15 16 17 18 19 20
0
21 22 23 24 25 26 27 28 29 30 31 32
1
Master Key
n5 n4 n3 n2 n1 n0
Note 1), 2)
Data Bit Rate
RF/(2n + 2)
PSK-
Modulation
CF
0
0
RF/2
Direct
0
0
0
0
0
0
1
RF/4
PSK1
0
0
0
0
1
1
0
RF/8
1
1
Res.
0
Unlocked
PSK2
0
0
0
1
0
1
Locked
PSK3
0
0
0
1
1
FSK1
0
0
1
0
0
FSK2
0
0
1
0
1
Mode-Defeat 1 0
0
1
1
0
Mode-Defeat 2 0
0
1
1
1
Manchester
0
1
0
0
0
Biphase ('50)
1
0
0
0
0
Biphase ('57)
1
1
0
0
0
MAXBLOCK
POR Delay
0
7 8
Inverse Data
0
6
Fast Write
1
5
ST-Sequence Terminator
3 4
PWD
2
OTP
1
AOR
Lock Bit
L
Block 0 Configuration Mapping – e5550 Compatibility Mode
X-Mode
Figure 4-2.
1) If Master Key = 6 and bit 15 set, then test-mode access is disabled and extended mode is active
2) If Master Key = 9 and bit 15 set, then extended mode is enabled
4.10
Modulator
The modulator consists of data encoders for the following basic types of modulation:
Table 4-1.
Types of e5550-compatible Modulation Modes
Mode
Direct Data Output
(1)
Encoding
FSK1a
FSK/8, FSK/5
“0” = RF/8;
“1” = RF/5
FSK2a(1)
FSK/8, FSK/10
“0” = RF/8;
“1” = RF/10
FSK1(1)
FSK/5, FSK/8
“0” = RF/5;
“1” = RF/8
(1)
FSK/10, FSK/8
“0” = RF/10;
“1” = RF/8
(2)
PSK1
Phase change when input changes
PSK2(2)
Phase change on bit clock if input high
FSK2
(2)
PSK3
Phase change on rising edge of input
Manchester
“0” = falling edge, “1” = rising edge
Bi-phase
“1” creates an additional mid-bit change
NRZ
“1” = damping on, “0” = damping off
Notes:
1. A common multiple of bit rate and FSK frequencies is recommended.
2. In PSK mode the selected data rate has to be an integer multiple of the PSK sub-carrier
frequency.
5
4863A–RFID–07/05
4.11
Sensor Input
Modulated output data stream depends on the state of the sensor input. The data stream is
inverted when external resistance, connected between Sensor input and VSS, is more than
RS > 100 kΩ (typical). Otherwise, the output data stream is not inverted (“normal”).
4.12
Memory
The memory is a 330-bit EEPROM, which is arranged in 10 blocks of 33 bits each. All 33 bits of
a block, including the lock bit, are programmed simultaneously.
Block 0 of page 0 contains the mode/configuration data, which is not transmitted during regularread operations. Block 7 of page 0 may be used as a write-protection password.
Bit 0 of every block is the lock bit for that block. Once locked, the block (including the lock bit
itself) is not re-programmable through the RF field.
Blocks 1 and 2 of page 1 contain traceability data and are transmitted with the modulation
parameters defined in the configuration register after the opcode “11” is issued by the reader
(Figure 5-6 on page 12). These traceability data blocks are programmed and locked by Atmel.
Figure 4-3.
Memory Map
Page 0
Page 1
0 1
32
1
Traceability data
Block 2
1
Traceability data
Block 1
L
User data or password
Block 7
L
User data
Block 6
L
User data
Block 5
L
User data
Block 4
L
User data
Block 3
L
User data
Block 2
L
User data
Block 1
L
Configuration data
Block 0
Not transmitted
6
32 bits
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
4.13
Traceability Data Structure
Block 1 and 2 of page 1 contain the traceability data and are programmed and locked by Atmel
during production testing(1). The most significant byte of block 1 is fixed to “E0”hex, the allocation
class (ACL) as defined in ISO/IEC 15963-1. The second byte is therefore defined as the manufacturer’s ID of Atmel (= “15”hex). The following 8 bits could be used as UID issuer identifier
(UID Bit 47 to 40). If not otherwise requested, the 5 most significant bits (customer identification
CID) are by default reset (= 00) as the Atmel standard value (other values may be assigned on
request to high volume customers as CID) and the least 3 bits (ICR) are used by Atmel for the IC
and/or foundry version of the ATA5570.
The lower 40 bits of the data, encode the traceability information of Atmel and conform to a
unique numbering system. These 40 data bits are divided in two sub-groups, a 5-digit BCD
coded lot ID number (LotID - 20 bit) and the binary wafer number (wafer# - 5 bit) concatenated
with the sequential die number on wafer (DW - 15 bit).
Note:
1. This is only valid for wafer delivery
Figure 4-4.
ATA5570 Traceability Data Structure
Example:
"15"
"E0"
"41"
"00"
8
Bit No.
1
9
...
16
MFC
...
31
...
LotID
1
...
12
17
...
CID
63 MSB
Block 2
Bit No.
8
ACL
Block 1
Bit value
...
24
ICR
...
...
32
LotID
32
wafer #
12 13
25
LSB
0
31
32
DW
17
18
...
20
"557"
ACL
MFC
UID
LotID
Wafer#
DW
Allocation class as defined in ISO/IEC 15963-1 = E0h
Manufacturer code of Atmel Corporation as defined in ISO/IEC 7816-6 = 15h
UID issuer identifier on request (respectively 5 bit CID and 3 bit ICR)
5-digit lot number, e.g., “41557”
5 bits for wafer#
15 bits encoded as sequential die on wafer number
7
4863A–RFID–07/05
5. Operating the ATA5570
5.1
Initialization and POR Delay
The Power-On-Reset (POR) circuit remains active until an adequate voltage threshold has been
reached. This in turn triggers the default start-up delay sequence. During this configuration
period of about 192 field clocks, the ATA5570 is initialized with the configuration data stored in
EEPROM block 0. If the POR delay bit is reset, no additional delay is observed after the configuration period. Tag modulation in regular-read mode will be observed about 3 ms after entering
the RF field. If the POR delay bit is set, the ATA5570 remains in a permanent damping state until
8190 internal field clocks have elapsed.
TINIT = (192 + 8190 × POR delay) × TC ≈ 67 ms;
TC = 8 µs at 125 kHz
Any field gap occurring during this initialization phase will restart the complete sequence. After
this initialization time the ATA5570 enters regular-read mode and modulation starts automatically, using the parameters defined in the configuration register.
5.2
Tag-to-reader Communication
During normal operation, the data stored within the EEPROM is cycled and the COIL1 and
COIL2 terminals are load modulated. This resistive load modulation can be detected at the
reader module.
5.3
Regular-read Mode
In regular-read mode, data from the memory is transmitted serially, starting with block 1, bit 1, up
to the last block (e.g., 7), bit 32. The last block which will be read is defined by the mode parameter field MAXBLK in EEPROM block 0. When the data block addressed by MAXBLK has been
read, data transmission restarts with block 1, bit 1.
The user may limit the cyclic datastream in regular-read mode by setting the MAXBLK between
0 and 7 (representing each of the 8 data blocks). If set to 7, blocks 1 through 7 can be read. If set
to 1, only block 1 is transmitted continuously. If set to 0, the contents of the configuration block
(normally not transmitted) can be read. In the case of MAXBLK = 0 or 1, regular-read mode can
not be distinguished from block-read mode.
Figure 5-1.
MAXBLK = 5
Examples of Different MAXBLK Settings
0
Block 1
Block 4
Block 5
Block 1
Block 2
Block 2
Block 1
Block 2
Block 1
Block 0
Block 0
Block 0
Block 0
Loading block 0
MAXBLK = 2
0
Block 1
Loading block 0
MAXBLK = 0
Block 0
0
Loading block 0
Every time the ATA5570 enters regular- or block-read mode, the first bit transmitted is a logical
“0”. The data stream starts with block 1, bit 1, continues through MAXBLK, bit 32, and cycles
continuously if in regular-read mode.
This behavior is different from the original e555x and helps to decode PSK-modulated data.
8
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
5.4
Block-read Mode
With the direct access command, the addressed block is repetitively read only. This mode is
called block-read mode. Direct access is entered by transmitting the page access opcode (“10”
or “11”), a single “0” bit, and the requested 3-bit block address, when the tag is in normal mode.
In password mode (PWD bit set), the direct access to a single block needs the valid 32-bit password to be transmitted after the page access opcode, whereas a “0” bit and the 3-bit block
address follow afterwards. In case the transmitted password does not match with the contents of
block 7, the ATA5570 tag returns to the regular-read mode.
Note:
5.5
A direct access to block 0 of page 1 will read the configuration data of block 0, page 0.
A direct access to block 3 to 7 of page 1 reads all data bits as zero.
e5550 Sequence Terminator
The sequence terminator (ST) is a special damping pattern which is inserted before the first
block and may be used to synchronize the reader. This e5550-compatible sequence terminator
consists of four bit periods with underlaying data values of “1”. During the second and the fourth
bit period, modulation is switched off (if Manchester coding is activated, then modulation is
switched on). Bi-phase modulated data blocks need fixed leading and trailing bits in combination
with the sequence terminator to be reliably identified.
The sequence terminator may be individually enabled by setting mode bit 29 (ST = “1”) in the
e5550-compatibility mode (X-mode = “0”).
In the regular-read mode, the sequence terminator is inserted at the start of each MAXBLK-limited read data stream. In block-read mode, after any block-write or direct access command, or if
MAXBLK was set to “0” or “1”, the sequence terminator is inserted before the transmission of the
selected block.
This behavior is different from former e5550-compatible ICs (T5551, T5554).
Figure 5-2.
Read Data Stream with Sequence Terminator
No terminator
Block 1
Block 2
MAXBLK
Block 1
Block 2
Regular read mode
Sequence terminator
ST = on
Block 1
Sequence terminator
Block 2
MAXBLK
Block 1
Block 2
9
4863A–RFID–07/05
Figure 5-3.
e5550-compatible Sequence Terminator Waveforms
Bit period
Sequence
Data "1"
Data "1"
Data "1"
Data "1"
Last bit
First Bit
Modulation
off (on)
Modulation
off (on)
Waveforms per different modulation types
bit "1" or "0"
V Coil PP
Manchester
FSK
Sequence terminator not suitable for Biphase or PSK modulation
5.6
Reader-to-tag Communication
Data is written to the tag by interrupting the RF field with short field gaps (on-off keying) in accordance with the e5550 write method. The time between two gaps encodes the “0” or “1”
information to be transmitted (pulse interval encoding). The duration of the gaps is usually 50 µs
to 150 µs. The time between two gaps is nominally 24 field clocks for a “0” and 54 field clocks for
a “1”. When there is no gap for more than 64 field clocks after a previous gap, the ATA5570 exits
the write mode. The tag starts with the command execution if the correct number of bits were
received. If there is a failure detected the ATA5570 does not continue and will enter regular-read
mode.
5.7
Start Gap
The initial gap is referred to as the start gap. This triggers the reader-to-tag communication. During this mode of operation, the receive damping is permanently enabled to ease gap detection.
The start gap may need to be longer than subsequent gaps in order to be detected reliably.
A start gap will be accepted at any time after the mode register has been loaded (≥ 3 ms). A single gap will not change the previously selected page (by former opcode “10” or “11”).
Figure 5-4.
Start of Reader-to-tag Communication
Read mode
Write mode
d1
Sgap
10
d0
Wgap
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
Table 5-1.
Write-data Decoding Scheme
Parameters
Remark
Symbol
Min
Max
Unit
Start gap
–
Sgap
10
50
FC
Write gap
Normal write mode
Wgap
8
30
FC
“0” data
d0
16
31
FC
“1” data
d1
48
63
FC
Write data in normal mode
5.8
Write-data Protocol
The ATA5570 expects to receive a dual-bit opcode as the first two bits of a reader command
sequence. There are three valid opcodes:
• The opcodes “10” and “11” precede all block-write and direct-access operations for page 0
and page 1
• The RESET opcode “00” initiates a POR cycle
• The opcode “01” precedes all test-mode write operations. Any test-mode access is ignored
after the master key (bits 1 to 4) in block 0 has been set to “6”. Any further modifications of
the master key are prohibited by setting the lock bit of block 0 or the OTP bit.
Writing has to follow these rules:
• Standard write needs the opcode, the lock bit, 32 data bits and the 3-bit address
(38 bits total)
• Protected write (PWD bit set) requires a valid 32-bit password after opcode and before data
and address bits
• For the AOR wake-up command an opcode and a valid password are necessary to select
and activate a specific tag
Note:
The data bits are read in the same order as written.
If the transmitted command sequence is invalid, the ATA5570 enters regular-read mode with the
previously selected page (by former opcode “10” or “11”).
Figure 5-5.
Complete Writing Sequence
Read mode
Op-code
Block 0 loading
Start gap
Read mode
Write mode
Block data
Block address
Programming
Lock bit
POR
11
4863A–RFID–07/05
Figure 5-6.
ATA5570 Command Formats
OP
5.9
Standard write
1p* L
Protected write
1p*
1
Password
32
AOR (wake-up command)
10
1
Password
32
Direct access (PWD = 1)
1p* 1
Password
32
Direct access (PWD = 0)
1p* 0
Page 0/1 regular read
1p*
Reset command
00
1
Data
2 Addr
32
2 Addr
L
1
0
2 Addr
0
Data
32
2 Addr
0
0
0
* p = page selector
Password
When password mode is active (PWD = 1), the first 32 bits after the opcode are regarded as the
password. They are compared bit-by-bit with the contents of block 7, starting at bit 1. If the comparison fails, the ATA5570 will not program the memory, instead it will restart in regular-read
mode once the command transmission is finished.
Note:
In password mode, MAXBLK should be set to a value below 7 to prevent the password from being
transmitted by the ATA5570.
Each transmission of the direct access command (two opcode bits, 32 bits password, “0” bit plus
3 address bits = 38 bits) needs about 18 ms. Testing all possible combinations (about 4.3 billion)
would take about two years.
5.10
Answer-on-request (AOR) Mode
When the AOR bit is set, the ATA5570 does not start modulation in the regular-read mode after
loading configuration block 0. The tag waits for a valid AOR data stream (“wake-up command”)
from the reader before modulation is enabled. The wake-up command consists of the opcode
(“10”) followed by a valid password. The selected tag will remain active until the RF field is
turned off or a new command with a different password is transmitted which may address
another tag in the RF field.
12
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
Table 5-2.
ATA5570 – Modes of Operation
PWD
AOR
Behavior of Tag After Reset Command or POR
De-activate Function
1
1
Answer-on-request (AOR) mode:
- Modulation starts after wake-up with a matching password
- Programming needs valid password
Command with non-matching password
deactivates the selected tag
1
0
Password mode:
- Modulation in regular-read mode starts after reset
- Programming and direct access needs valid password
0
--
Normal mode:
- Modulation in regular-read mode starts after reset
- Programming and direct access without password
Figure 5-7.
Answer-on-request (AOR) Mode
Modulation
VCoil 1 - Coil 2
POR
Figure 5-8.
Loading block 0
No modulation
because AOR = 1
AOR wake-up command (with valid PWD)
Coil Voltage After Programming of a Memory Block
VCoil 1- Coil 2
5.6 ms
Write data to tag
Programming and
data verification
Read programmed
memory block
(Block-read mode)
POR/
or
single
gap
Read block 1..MAXBLK
(Regular-read mode)
13
4863A–RFID–07/05
Figure 5-9.
Anticollision Procedure Using AOR Mode
Reader
Tag
Init tags with
AOR = "1" , PWD = "1"
Field OFF => ON
POWER ON RESET
Read configuration
Wait for tW > 2.5 ms
Enter AOR mode
Wait for OPCODE + PWD
=> "wake up command"
"Select a single tag"
Send OPCODE + PWD
=> "wake up command"
Receive damping ON
NO
Password correct ?
YES
Send block 1...MAXBLK
Decode data
NO
All tags read ?
YES
Field ON => OFF
EXIT
14
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
5.11
Programming
When all necessary information has been received by the ATA5570, programming may proceed.
There is a clock delay between the end of the writing sequence and the start of programming.
Typical programming time is 5.6 ms. This cycle includes a data verification read to grant secure
and correct programming. After programming is successfully executed, the ATA5570 enters
block-read mode transmitting the block just programmed (Figure 5-8 on page 13).
Note:
This timing and behavior is different from the e555x-family predecessors.
6. Error Handling
Several error conditions can be detected to ensure that only valid bits are programmed into the
EEPROM. There are two error types, which lead to two different actions.
6.1
Errors During Writing
The following detectable errors could occur during writing data to the ATA5570:
• Wrong number of field clocks between two gaps (i.e., not a valid “1” or “0” pulse stream)
• Password mode is activated and the password does not match the contents of block 7
• The number of bits received in the command sequence is incorrect
Valid bit counts accepted by the ATA5570 are:
Password write
70 bits
(PWD = 1)
Standard write
38 bits
(PWD = 0)
AOR wake up
34 bits
(PWD = 1)
Direct access with PWD
38 bits
(PWD = 1)
Direct access
6 bits
(PWD = 0)
Reset command
2 bits
Page 0/1 regular-read
2 bits
If any of these erroneous conditions are detected, the ATA5570 enters regular-read mode, starting with block 1 of the page defined in the command sequence.
6.2
Errors Before/During Programming
If the command sequence was received successfully, the following error could still prevent
programming:
• The lock bit of the addressed block is already set
In case of a locked block, programming mode will not be entered. The ATA5570 reverts to blockread mode, continuously transmitting the currently addressed block.
15
4863A–RFID–07/05
If the command sequence is validated and the addressed block is not write-protected, the new
data will be programmed into the EEPROM memory. The new state of the block-write protection
bit (lock bit) will be programmed at the same time accordingly.
Each programming cycle consists of 4 consecutive steps.
1. Erase block
2. Erase verification (data = “0”)
3. Programming
4. Write verification (corresponding data bits = “1”)
• If a data verification error is detected after an executed data block programming, the tag will
stop modulation (modulation defeat) until a new command is transmitted.
Figure 6-1.
ATA5570 Functional Diagram
Power-on Reset
* p = page selector
AOR = 1
Setup Modes
AOR Mode
AOR = 0
Regular-read Mode
Page 0 or 1
Page 0
addr = 1 to maxblk
Block-read Mode
gap
Start
Gap
addr = current
command mode
gap
single gap
Modulation Defeat
Page 1
OP(00)
Reset
to page 0
Direct access OP (1p)*
Command Decode
OP(11..)
OP (1p)*
Page 0
OP(10..)
OP(01)
Write
OP(1p)*
Test-mode
if master key <> 6
Write
Number of bits
Password check
Lock bit check
Data verification failed
16
Program and Verify
fail
data = old
fail
data = old
fail
data = old
ok
data = new
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
7. ATA5570 in Extended Mode (X-mode)
In general, the block 0 setting of the master key (bits 1 to 4) to the value “6” or “9” together with
the X-mode bit will enable the extended mode functions.
• Master key = “9”: Test mode access and extended mode are both enabled.
• Master key = “6”: Any test mode access will be denied but the extended mode is still enabled.
Any other master key setting will prevent the activation of the ATA5570 extended mode options,
even when the X-mode bit is set.
7.1
Binary Bit-rate Generator
In extended mode the data rate is binary programmable to operate at any data rate between
RF/2 and RF/128 as given in the formula below.
Data rate = RF/(2n + 2)
7.2
OTP Functionality
If the OTP bit is set to “1”, all memory blocks are write protected and behave as if all lock bits are
set to “1”. If, additionally, the master key is set to “6”, the ATA5570 mode of operation is locked
forever (= OTP functionality).
If the master key is set to “9”, the test-mode access allows the re-configuration of the tag.
1
0
0
0
9 10 11 12
13 14 15 16 17 18 19 20
0
21 22 23 24 25 26 27 28 29 30 31 32
1
Master Key
n5 n4 n3 n2 n1 n0
Note 1), 2)
Data Bit Rate
RF/(2n + 2)
PSK-
Modulation
CF
0
0
RF/2
Direct
0
0
0
0
0
0
1
RF/4
PSK1
0
0
0
0
1
1
0
RF/8
1
1
Res.
0
Unlocked
PSK2
0
0
0
1
0
1
Locked
PSK3
0
0
0
1
1
FSK1
0
0
1
0
0
FSK2
0
0
1
0
1
Mode-Defeat 1 0
0
1
1
0
Mode-Defeat 2 0
0
1
1
1
Manchester
0
1
0
0
0
Biphase ('50)
1
0
0
0
0
Biphase ('57)
1
1
0
0
0
MAXBLOCK
POR Delay
0
7 8
Inverse Data
0
6
Fast Write
1
5
ST-Sequence Terminator
3 4
PWD
2
OTP
1
AOR
Lock Bit
L
Block 0 – Configuration Map in Extended Mode (X-mode)
X-Mode
Figure 7-1.
1) If Master Key = 6 and bit 15 set, then test-mode access is disabled and extended mode is active
2) If Master Key = 9 and bit 15 set, then extended mode is enabled
17
4863A–RFID–07/05
Table 7-1.
ATA5570 Types of Modulation in Extended Mode and Sensor Input RS < 100 kΩ
Typical
Mode
Direct Data Output Encoding
Inverse Data Output Encoding
FSK1(1)
FSK/5, FSK/8;
“0” = RF/5; “1” = RF/8
FSK/8, FSK/5;
“0” = RF/8; “1” = RF/5 (= FSK1a)
FSK2(1)
FSK/10, FSK/8;
“0” = RF/10; “1” = RF/8
FSK/8, FSK/10;
“0” = RF/8; “1” = RF/10 (= FSK2a)
PSK1(2)
Phase change when input changes
Phase change when input changes
(2)
Phase change on bit clock if input high
Phase change on bit clock if input low
(2)
PSK3
Phase change on rising edge of input
Phase change on falling edge of input
Manchester
“0” = falling edge
“1” = rising edge on mid-bit
“1” = falling edge
“0” = rising edge on mid-bit
Bi-phase 1 (’50)
“1” creates an additional mid-bit change “0” creates an additional mid-bit change
Bi-phase 2 (’57)
“0” creates an additional mid-bit change “1” creates an additional mid-bit change
NRZ
“1” = damping on, “0” = damping off
PSK2
Notes:
“0” = damping on, “1” = damping off
1. A common multiple of bit rate and FSK frequencies is recommended.
2. In PSK mode the selected data rate has to be an integer multiple of the PSK sub-carrier
frequency.
7.3
Sequence Start Marker
Figure 7-2.
ATA5570 Sequence Start Marker in Extended Mode
Sequence Start Marker
Block-read mode
10
Block n
Regular-read mode
10
Block 1
01
Block n
Block 2
10
Block n
01
MAXBLK
01
Block 1
Block n
Block 2
10
Block n
01
MAXBLK
10
The ATA5570 sequence-start marker is a special damping pattern which may be used to synchronize the reader. The sequence start marker consists of two bits (“01” or “10”) which are
inserted as header before the first block to be transmitted if the bit 29 in extended mode is set. At
the start of a new block sequence, the value of the two bits is inverted.
18
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
7.4
Inverse Data Output
The ATA5570 supports in its extended mode (X-mode) an inverse data output option. If inverse
data is enabled, the modulator as shown in Figure 7-3 works on inverted data (see Table 7-1).
This function is supported for all basic types of encoding. Table 7-1 shows the modulation, when
RS < 100 kΩ typical.
Figure 7-3.
Data Encoder for Inverse Data Output
PSK1
PSK2
PSK3
Sensor in
Intern out
data
D
XOR
Sync
XOR
Direct/NRZ
Mux
Data output
FSK1
FSK2
Data clock CLK
R
Manchester
Bi-phase
Modulator
Inverse data output
7.5
Fast Write
In the optional fast-write mode the time between two gaps is nominally 12 field clocks for a “0”
and 27 field clocks for a “1”. When there is no gap for more than 32 field clocks after a previous
gap, the ATA5570 will exit the write mode. Please refer to Table 7-2 and Figure 5-6 on page 12.
Table 7-2.
Fast Write Decoding Schemes
Parameters
Start gap
Write gap
Write data in normal mode
Write data in fast mode
Remark
Symbol
Min
Max
Unit
–
Sgap
10
50
FC
Normal write mode
Wngap
8
30
FC
Fast write mode
Wfgap
8
20
FC
“0” data
d0
16
31
FC
“1” data
d1
48
63
FC
“0” data
d0
8
15
FC
“1” data
d1
24
31
FC
19
4863A–RFID–07/05
20
RF Field
Manchester
Coded
Inverted Modulator
Signal
Data Stream
12
8 FC
8
9
8 FC
16
1
Data Rate =
16 Field Clocks (FC)
1
8
0
9
16
1
8
0
16 1
8
1
9
16
12
8
9
1
16 1
8
9
0
16
Figure 7-4.
Example of Manchester Coding With Data Rate RF/16
ATA5570 [Preliminary]
4863A–RFID–07/05
4863A–RFID–07/05
RF Field
Inverted Modulator
Signal
Bi-phase Coded
Data Stream
12
8
9
8 FC
16
1
89
0
16
1
8
0
16
1
8
1
9
16
12
8
9
1
16
1
89
0
16
Figure 7-5.
8 FC
1
Data Rate =
16 Field Clocks (FC)
ATA5570 [Preliminary]
Example of Bi-phase Coding With Data Rate RF/16
21
Example: FSK1a Coding With Data Rate RF/40, Subcarrier f0 = RF/8, f1 = RF/5
22
RF Field
f1 = RF/5
f0 = RF/8,
Inverted Modulator
Signal
Data Stream
1 5
1
Data Rate =
40 Field Clocks (FC)
1
8
0
1
8
0
1 5
1
1 5
1
1
8
0
Figure 7-6.
ATA5570 [Preliminary]
4863A–RFID–07/05
4863A–RFID–07/05
RF Field
Subcarrier RF/2
Inverted Modulator
Signal
Data Stream
12
8 9
16 1
8 FC
8
0
16 1
8
0
16 1
8
1
16 1
8
1
16 1
8
0
Figure 7-7.
8 FC
1
Data Rate =
16 Field Clocks (FC)
ATA5570 [Preliminary]
Example of PSK1 Coding With Data Rate RF/16
23
24
RF Field
Inverted
Modulator Signal
Subcarrier RF/2
Data Stream
12
8 FC
8 9
8 FC
16 1
1
Data Rate =
16 Field Clocks (FC)
8
0
16 1
8
0
16 1
8
1
16 1
8
1
16 1
8
0
Figure 7-8.
Example of PSK2 Coding With Data Rate RF/16
ATA5570 [Preliminary]
4863A–RFID–07/05
4863A–RFID–07/05
RF Field
Inverted
Modulator Signal
Sub-carrier RF/2
Data Stream
12
89
8 FC
16 1
8
0
16 1
8
0
16 1
8
1
16 1
8
1
16 1
8
0
Figure 7-9.
8 FC
1
Data Rate =
16 Field Clocks (FC)
ATA5570 [Preliminary]
Example of PSK3 Coding With Data Rate RF/16
25
8. Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters
Pin
Symbol
Value
Unit
Maximum DC current into COIL1/COIL2 (t = 1 ms)
2, 7
Icoil
20
mA
Maximum AC current into COIL1/COIL2 (f = 125 kHz)
2, 7
Icoil p
20
mA
2, 7
Ptot
100
mW
Operating ambient temperature range
Tamb
–25 to +105
°C
Storage temperature range(2)
Tstg
–40 to +150
°C
Power dissipation (dice)
Notes:
(1)
1. Free-air condition, time of application: 1s
2. Data retention reduced at high temperature
9. Operating Characteristics
All parameters given are valid for Tamb = +25°C and fcoil = 125 kHz, unless otherwise specified.
No.
1
2.1
2.2
Parameters
Test Conditions
Pin
Symbol
Min
Typ
Max
Unit
100
Type*
RF frequency range
2, 7
fRF
125
150
kHz
Supply current (without Tamb = 25°C
current consumed by
the external LC tank
Read
circuit and without
external resistance on Tamb = –25°C to +85°C
2, 7
IDD
1.5
3
µA
T
2, 7
IDD
2
4
µA
Q
2, 7
Vcoil pp
10
Vclamp
Vpp
Q
2, 7
Vclamp
17
23
Vpp
T
2.5
3
ms
Q
20
50
year
Q
sensor input)
3.1
Coil voltage (AC supply) Necessary for read(1)
4
Clamp voltage
5
Startup time(2)
6.1
6.2
Data retention
10 mA current into
COIL1/COIL2
tstartup
Top = 55°C
tretention
10
Tstg = 150°C
tretention
96
h
T(3)
ncycle
100,000
cycles
Q
RT
50
100
200
kΩ
T
CR
323
340
357
pF
T
QL
15
20
25
7
Programming cycles
Erase all/Write all
8
Sensor Input
Trip point resistance
(modulation inverted)
9
Resonance
capacitor CR
See Figure 2-1 on page 2
10
Q-factor of coil LR
4, 5
Q
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter,
Q = guaranteed based on initial product qualification data, T = directly or indirectly tested during production.
Notes: 1. Current into COIL1/COIL2 has to be limited to 20 mA
2. Time from field on to modulation start
3. Tested on wafer basis
26
ATA5570 [Preliminary]
4863A–RFID–07/05
ATA5570 [Preliminary]
10. Reliability
Parameters
Symbol
Value
Unit
Electrostatic discharge ESD S.5.1 (Human Body Model)
Vmax
2000
V
Electrostatic discharge JEDEC A115A (Machine Model)
Vmax
200
V
tL
1008
h
Lifetime in SO8 at Top =150°C
Figure 10-1. Measurement Setup for IDD and Vmod
R
BAT68
-
VOUTmax
Coil 1
+
Coil 2
BAT68
11. Ordering Information
Extended Type Number
Package
Remarks
ATA5570-TAQY
SO8
–
(ATA557001-DDW) planned
Wafer
–
12. Package Information
Package SO8
Dimensions in mm
5.2
4.8
5.00
4.85
3.7
1.4
0.25
0.10
0.4
1.27
6.15
5.85
3.81
8
0.2
3.8
5
technical drawings
according to DIN
specifications
1
4
27
4863A–RFID–07/05
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© Atmel Corporation 2005. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are ® and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
4863A–RFID–07/05
Similar pages