ML62 ML62 Series Positive Voltage Regulator Application Features Battery Powered Equipment Palmtops Portable Cameras and Video Recorders Reference Voltage Sources General Description CMOS Low Power Consumption : Typical 3.3uAat Vout=5.0V Output Voltage Range : 1.1V to 6.0V in 0.1V increments HighlyAccurate: Output Voltage + 3% for 1.1V to 1.9V Output Voltage + 2% for 2.0V to 6.0V Maximum Output Current: 250mA (within the maximum power dissipation, Vout=5.0V) Small Input-Output Voltage Differential: 0.12V at 100mAand 0.38V at 200mA Input stability: Typ. 0.2%/V PackageAvailable: SOT- 23 (150mW), SOT- 89 (500mW) & TO - 92 (300mW) Block Diagram The ML62 is a group of positive voltage output, three-pin regulator which provides high output current even when the input/output voltage differential is small. The ML62 consists of a high-precision voltage reference, an error correction circuit, and a current limited output driver. Absolute Maximum Ratings Parameter Input Voltage Output Current Output Voltage SOT-23 Continuous Total Power Dissipation SOT-89 TO-92 Operating Ambient Temperature Storage Temperature Symbol VIN IOUT VOUT Ratings 10 500 VSS-0.3 ~VIN+0.3 150 Units V mA V Pd 500 mW Topr Tstg 300 -40 ~ +70 -40 ~ +70 P1/12 o C C o Rev. G, July 2005 ML62 Pin Configuration SOT-23 Package Pin Number SOT23 SOT89 TO-92 1 1 1 3 2 2 2 3 3 SOT-89 TO-92 Pin Name Function VSS VIN VOUT Ground Power Input Output Standard Circuit Note on Use 1. Oscillation may occur as a result of the impedance present between the power supply and the IC’s input. Please use a capacitor (CIN) of at least 1uF, when the impedance is 10 ohm or more. With a large output current, Voltage output can be stabilised by increasing capacitor (CIN) size. If CIN is small and capacitor (CL) size is increased, oscillation may occur. In such cases, Voltage output can be stabilised by either increasing the size of CIN or decreasing the size of CL. 2. Please ensure that output current (IOUT) is less than Pd / (VIN-VOUT) and does not exceed the stipulated Continuous Total Power Dissipation value (Pd). Test Circuit Test Circuit 2 Test Circuit 1 P2/12 Rev. G, July 2005 ML62 Electrical Characteristic ML62502 VOUT(T)=5.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Conditions IOUT=40mA VIN=6.0V VIN=6.0V, VOUT(E) ≥ 4.5V VIN=6.0V, 1mA≤IOUT≤100mA IOUT=100mA IOUT=200mA VIN=6.0V IOUT=40mA 6.0V≤VIN≤10.0V Min Typ Max Units Circuit 4.900 5.000 5.100 V 1 40 120 380 3.3 80 400 750 4.5 mA mV mV mV uA 1 1 1 1 2 0.2 0.3 %V 1 10 V - Units Circuit 250 ML62402 VOUT(T)=4.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Conditions IOUT=40mA VIN=5.0V VIN=5.0V, VOUT(E) ≥3.6V VIN=5.0V, 1mA≤IOUT≤100mA IOUT=90mA IOUT=180mA VIN=5.0V IOUT=40mA 5.0V≤VIN≤10.0V Min Typ Max 3.920 4.000 4.080 V 1 45 170 400 3.0 90 400 750 4.5 mA mV mV mV uA 1 1 1 1 2 0.2 0.3 %V 1 10 V - Units Circuit 200 ML62302 VOUT(T)=3.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Conditions IOUT=40mA VIN=4.0V VIN=4.0V, VOUT(E) ≥2.7V VIN=4.0V, 1mA≤IOUT≤80mA IOUT=80mA IOUT=150mA VIN=4.0V IOUT=40mA 4.0V≤VIN≤10.0V Min Typ Max 2.940 3.000 3.060 V 1 45 180 400 2.8 90 450 850 4.5 mA mV mV mV uA 1 1 1 1 2 0.2 0.3 %V 1 10 V - Units Circuit 150 ML62202 VOUT(T)=2.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Conditions IOUT=40mA VIN=3.0V VIN=3.0V, VOUT(E) ≥1.8V VIN=3.0V, 1mA≤IOUT≤60mA IOUT=60mA IOUT=100mA VIN=3.0V IOUT=40mA 3.0V≤VIN≤10.0V Min Typ Max 1.960 2.000 2.040 V 1 45 180 400 2.5 90 450 850 4.5 mA mV mV mV uA 1 1 1 1 2 0.2 0.3 %V 1 10 V - 100 Note : 1. VOUT(T) = Specified Output Voltage. 2. VOUT(E) = Effective Output Voltage (i.e. the output voltage when (VOUT(T)+1.0V) is provided at the VIN pin while maintaining a certain IOUT value). 3. Vdif = VIN1(Note 4) – VOUT(E) 4. VIN1 = The input voltage at the time 98% of VOUT (E) is output (input voltage has been gradually reduced). P3/12 Rev. G, July 2005 ML62 Electrical Characteristics by Output Voltage Part Number Output voltage VOUT(V) Conditions ML62113 ML62123 ML62133 ML62143 ML62153 ML62163 ML62173 ML62183 ML62193 ML62202 ML62212 ML62222 ML62232 ML62242 ML62252 ML62262 ML62272 ML62282 ML62292 ML62302 ML62312 ML62322 ML62332 ML62342 ML62352 ML62362 ML62372 ML62382 ML62392 ML62402 ML62412 ML62422 ML62432 ML62442 ML62452 ML62462 ML62472 ML62482 ML62492 ML62502 ML62512 ML62522 ML62532 ML62542 ML62552 ML62562 ML62572 ML62582 ML62592 ML62602 MIN. 1.067 1.164 1.261 1.358 1.455 1.552 1.649 1.746 1.843 1.960 2.058 2.156 2.254 2.352 2.450 2.548 2.646 2.744 2.842 2.940 3.038 3.136 3.234 3.332 IOUT=40mA 3.430 VIN=VOUT(T)+1V 3.528 3.626 3.724 3.822 3.920 4.018 4.116 4.214 4.312 4.410 4.508 4.606 4.704 4.802 4.900 4.998 5.096 5.194 5.292 5.390 5.488 5.586 5.684 5.782 5.880 TYP. 1.100 1.200 1.300 1.400 1.500 1.600 1.700 1.800 1.900 2.000 2.100 2.200 2.300 2.400 2.500 2.600 2.700 2.800 2.900 3.000 3.100 3.200 3.300 3.400 3.500 3.600 3.700 3.800 3.900 4.000 4.100 4.200 4.300 4.400 4.500 4.600 4.700 4.800 4.900 5.000 5.100 5.200 5.300 5.400 5.500 5.600 5.700 5.800 5.900 6.000 Max Output Current IOUT max(mA) Load Stability ∆ VOUT(mV) Conditions TYP. MAX. MAX. Conditions MIN. 1.133 1.236 1.339 1.442 VIN=VOUT(T)+1V 80 1.545 1mA<IOUT<40mA 1.648 1.751 1.854 1.957 2.040 2.142 2.244 2.346 VIN=VOUT(T)+1V 2.448 100 1mA<IOUT<60mA 2.550 2.652 2.754 2.856 2.958 3.060 3.162 3.264 3.366 VIN= VOUT(T)+1V 3.468 VIN=VOUT(T)+1V 150 1mA<IOUT<80mA 3.570 VOUT(E)> 3.672 VOUT(T)*0.9 3.774 3.876 3.978 4.080 4.182 4.284 4.386 VIN=VOUT(T)+1V 4.488 200 1mA<IOUT<100mA 4.590 4.692 4.794 4.896 4.998 5.100 5.202 5.304 5.406 5.508 VIN=VOUT+1V 250 5.610 1mA<IOUT<100mA 5.712 5.814 5.916 6.018 6.120 P4/12 45 90 I-O Voltage Differential Vdif1(mV) Conditions TYP. MAX. IOUT=20mA 250 450 IOUT=30mA 250 450 IOUT=40mA 250 450 45 90 IOUT=60mA 180 450 45 90 IOUT=80mA 180 450 45 90 IOUT=90mA 170 400 40 80 IOUT=100mA 120 400 Rev. G, July 2005 ML62 Part Number I-O Voltage Differential Vdif2(mV) Conditions ML62113 ML62123 ML62133 ML62143 ML62153 ML62163 ML62173 ML62183 ML62193 ML62202 ML62212 ML62222 ML62232 ML62242 ML62252 ML62262 ML62272 ML62282 ML62292 ML62302 ML62312 ML62322 ML62332 ML62342 ML62352 ML62362 ML62372 ML62382 ML62392 ML62402 ML62412 ML62422 ML62432 ML62442 ML62452 ML62462 ML62472 ML62482 ML62492 ML62502 ML62512 ML62522 ML62532 ML62542 ML62552 ML62562 ML62572 ML62582 ML62592 ML62602 TYP. MAX. IOUT=40mA 450 850 IOUT=60mA 450 850 IOUT=80mA 450 850 IOUT=100mA 400 850 IOUT=150mA 400 850 Supply Current ISS(uA) Conditions TYP. MAX. 2.0 4.5 2.5 4.5 2.8 4.5 VIN=VOUT(T)+1V Input Stability Input Voltage ∆ VOUT/(∆ ∆ VIN*VOUT) (%V) VIN(V) Conditions TYP. MAX. MAX. 0.2 IOUT=40mA VOUT(T)+1V<VIN<10V 10 0.2 IOUT=180mA 400 750 3.0 4.5 IOUT=200mA 380 750 3.3 4.5 P5/12 0.4 0.3 Rev. G, July 2005 ML62 Typical Performance Characteristics 1) Output Voltage vs. Output Current ML62502 ML62302 VIN = 4.0V VIN = 6.0V 5.1 3.1 Topr =80 C Topr =80 C 5.05 3.05 5 3 Output Voltage VOUT(V) Output Voltage VOUT(V) Topr =25 C 4.95 Topr =-40 C 4.9 4.85 4.8 Topr =25 C 2.95 Topr =-40 C 2.9 2.85 2.8 4.75 2.75 4.7 2.7 0 50 100 150 200 0 50 Output Current IOUT(mA) 100 150 200 Output Current IOUT(mA) 2) Output Voltage vs. Input Voltage ML62502 ML62302 Topt = 25℃ CL = 0.1uF(Tantalum) Topt = 25℃ CL = 0.1uF(Tantalum) 5.2 3.1 5.1 Output Voltage VOUT(V) Output Voltage VOUT(V) 5 4.9 Iout = 1mA 4.8 Iout = 40mA 4.7 4.6 4.5 Iout = 10mA 4.4 2.9 Iout = 1mA 2.7 Iout = 40mA 2.5 Iout = 10mA 2.3 4.3 4.2 2.1 4.5 4.7 4.9 5.1 5.3 5.5 2.5 2.7 2.9 Input Voltage VIN(V) 3.1 3.3 3.5 Input Voltage VIN(V) 3) Input/Output Voltage Differential vs. Output Current ML62302 ML62502 CL = 0.1uF(Tantalum) CL = 0.1uF(Tantalum) 1.8 1 Topr =80 C Topr =25 C 0.6 0.4 Topr =-40 C 0.2 0 0 50 100 -0.2 150 Input/Output Voltage Diff Vdif(V) Input/Output Voltage Diff Vdif(V) 1.6 0.8 1.4 1.2 Topr =80 C 1 0.8 Topr =25 C 0.6 0.4 Topr =-40 C 0.2 200 0 -0.2 Output Current IOUT(mA) 0 50 100 150 200 Output Current IOUT(mA) P6/12 Rev. G, July 2005 ML62 4) Supply Current vs. Input Voltage ML62502 ML62302 3.5 3 Topr =80 C Topr =80 C 2.5 Topr =25 C Supply Current ISS(uA) Supply Current ISS(uA) 3 2.5 Topr =-40 C 2 1.5 1 Topr =25 C 2 Topr =-40 C 1.5 1 0.5 0.5 0 0 0 2 4 6 8 10 12 0 2 4 6 8 10 12 Input Voltage VIN(V) Input Voltage VIN(V) 5) Output Voltage vs. Ambient Temperature ML62502 ML62302 VIN = 6.0V CL = 0.1uF (Tantalum) 5.1 VIN = 4.0V CL = 0.1 uF(Tantalum) 3.1 Output Voltage VOUT(V) Output Voltage VOUT(V) 5.05 IOUT = 10mA 5 4.95 IOUT = 40mA 4.9 3.05 IOUT = 10mA 3 IOUT = 40mA 2.95 4.85 2.9 4.8 -60 -40 -20 0 20 40 60 80 -60 100 -40 -20 0 20 40 60 80 100 Ambient Temp Topr(℃ ℃) Ambient Temp Topr(℃ ℃) 6) Supply Current vs. Ambient Temperature ML62502 ML62302 VIN = 6.0V VIN = 4.0V 3.5 2.8 2.6 2.4 Supply Current ISS(uA) Supply Current ISS(uA) 3 2.5 2 2.2 2 1.8 1.6 1.4 1.5 1.2 1 1 -60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100 Ambient Temp Topr(℃ ℃) Ambient Temp Topr(℃ ℃) P7/12 Rev. G, July 2005 ML62 Ordering Information Designator a b c d G Description Output Voltage eg. 30=3.0V 50=5.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Package Type M = SOT-23 P = SOT-89 T = TO-92 Device Orientation R = Embossed Tape (Orientation of Device : Right) L = Embossed Tape (Orientation of Device : Left) B = Bag (TO-92) H = Paper Tape (TO-92) G = Lead Free Part Marking SOT-23 : Designator Description 1 Type R = Positive Voltage Regulator 2,3 Output Voltage eg. 30 = 3.0V 4 Internal Code SOT-89 : Designator 1 2,3 4 5 Description Type R = Positive Voltage Regulator Output Voltage eg. 30 = 3.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Internal Code TO-92 : Designator 1 2,3 4 5 6, 7 8, 9 Description Type R = Positive Voltage Regulator Output Voltage eg. 30 = 3.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Internal code Year Code eg. 05 = Year 2005 Week Code eg. 30 = Week 30 P8/12 Rev. G, July 2005 ML62 Packaging Information SOT-23 : SOT-89 : (0.8) 1.5 ± 0.1 4.5 ± 0.1 0.15 -0.1 -0.05 -0.1 1.72 ± 0.1 0.4 -0.05 4.25 max 2.45 ± 0.15 min. 0.2 1.1 mm 1.6 +1.2 -0.0.1 2.8 ± 0.2 0 ~ 0.1 (0.95) 0.42 ± 0.06 1.9 ± 0.2 0.42 ± 0.06 1.5 ± 0.1 2.9 ± 0.2 TO-92 : 1.5 ± 0.1 1.27 4.2 max 1.27 0.4 ± 0.04 0.49 ± 0.06 1.1 ± 0.1 ∅5.2 max 12.7 min 5.3 max Units : mm Recommended Pattern Layout 2.2 SOT-23 : 3.7 0.9 SOT-89 2.4 45º 1.5 1.9 0.8 45º 1.0 1. 0 P9/12 1.6 1.0 Rev. G, July 2005 ML62 Tape and Reel Information SOT-23 : SIZE (mm) A ∅ 178 ± 0.8 B 2 ± 0.2 C ∅ 13 ± 0.2 D ∅ 21 ± 0.8 G 8 ± 0.5 H ∅ 60 3,000 pcs / reel SOT-23 Taping Specifications : 4 ± 0.1 ∅1.5 + 0.1 -0 4 ± 0.1 8 ± 0.2 3.5 ± 0.05 1.75 ± 0.1 2 ± 0.05 ∅ 1.1 ± 0.1 Direction of feed Direction of feed “L” type [Orientation of Device: Left] Reverse Type “R” type [Orientation of Device: Right] Standard Type P10/12 Rev. G, July 2005 ML62 SOT-89 : SIZE (mm) B 2 ± 0.2 C ∅ 13 ± 0.2 D ∅ 21 ± 0.8 G 12 ± 0.5 H ∅ 60 ∅ 1.5 + 0.1 0 12.0 ± 0.2 5.65 ± 0.05 1.5 ± 0.1 2.0 ± 0.05 ∅ 178 ± 0.8 1,000 pcs / reel SOT-89 Taping Specifications : 4.0 ± 0.1 A 8.0 ± 0.1 Direction of feed Direction of feed “L” type [Orientation of Device: Left] Reverse Type “R” type [Orientation of Device: Right] Standard Type P11/12 Rev. G, July 2005 ML62 TO-92 Taping Specifications : W W1 WO L1 H0 H W2 H1 P P2 t F D PO SIZE (mm) P 12.7 ± 1.0 PO 12.7 ± 0.3 P2 6.35 ± 0.4 F 2.5 2,000 pcs / box + 0.45 - 0.15 W 18.0 ± 1.0 WO 6.0 ± 0.3 W1 9.0 ± 0.5 W2 0.5 MAX H 19.0 ± 0.5 H0 16.0 ± 0.5 H1 32.25 MAX D ∅ 4.0 ± 0.2 t 0.6 ± 0.2 L1 3.5 MIN The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. P12/12 Rev. G, July 2005