FEATURES • • • • • • • –55° to +125°C operation 16 to 40 VDC input Fully Isolated Magnetic feedback Fixed frequency Topology – Single Ended Forward 50 V for up to 50 ms transient protection • Inhibit and synchronization functions • Indefinite short circuit protection • Up to 84% efficiency, 21 watts/in3 MHD SERIES 20 WATT DC/DC CONVERTERS 28 VOLT INPUT MODELS VDC OUTPUT SINGLE 5 12 15 18 DUAL ±5 ±12 ±15 Size (max.): Non-flanged, case H2 2.125 x 1.125 x 0.400 inches (53.98 x 28.58 x 10.16 mm) Flanged case, K3 2.910 x 1.125 x 0.400 inches (73.91 x 28.58 x 10.16 mm) See Section B8, cases H2 and K3 for dimensions. Weight: 52 grams max., flanged 55 grams max. Screening: Standard, ES, or 883 (Class H). See Section C2 for screening options, see Section A5 for ordering information. DESCRIPTION SYNCHRONIZATION The MHD Series™ of DC/DC converters offers up to 20 watts of output power over the full military temperature range with up to 84% efficiency. Thick-film hybrid techniques provide military/aerospace reliability levels and optimum miniaturization. The MHD Series power density rating is up to 21 watts/in3. The MHD offers a synchronization feature that allows the designer to match the switching frequency of the converter to the frequency of the system clock. In free-run (unsynchronized) mode, the MHD unit switches at 625 kHz (nominal). In sync mode, the converter will run at any frequency between 500 kHz and 675 kHz. The sync control operates with a quasi-TTL signal at any duty cycle between 40% and 60%. MHD converters are packaged in hermetically sealed metal cases, making them ideal for use in military, aerospace and other high reliability applications. Units are available with standard screening, “ES” screening, or fully compliant SMD versions (see Section C2 for screening conditions). Synchronizing the converter with the system clock allows the designer to confine switching noise to clock transitions, minimizing interference and reducing the need for filtering. The sync pin should be connected to input common pin when not in use. CONVERTER DESIGN WIDE VOLTAGE RANGE The MHD converters are constant frequency, pulse-width modulated switching regulators which use a quasi-square wave, single ended, forward converter design. Tight load regulation (5 mV typical) is maintained via wide bandwidth magnetic feedback and, on single output models, through use of remote sense. On dual output models, the positive output is independently regulated and the negative output is cross regulated through the use of tightly coupled magnetics and shunt regulators. The MHD converters are designed to provide full power operation over a full 16 to 40 VDC voltage range. Operation below 16 volts, including MIL-STD-704E emergency power conditions is possible with derated power. Refer to the low line dropout graph (Figure 15) for details. Indefinite short circuit protection and overload protection are provided by a constant current-limit feature. This protective system senses current in the converter’s secondary stage and limits it to approximately 115% of the maximum rated output current. MHD converters are provided with internal filtering capacitors that help reduce the need for external components in normal operation. For systems that require compliance with MIL-STD-461C’s CE03 standard, Interpoint offers filter/transient suppression modules (including the FMC-461, FMD-461 and FM-704A series filters) which will result in compliance. Contact your Interpoint representative for further details. IMPROVED DYNAMIC RESPONSE The MHD feed-forward compensation system provides excellent dynamic response and noise rejection. Audio rejection is typically 50 dB. The min. to maximum step line transient response is typically less than 4%. INHIBIT FUNCTION MHD converters provide an inhibit terminal that can be used to disable internal switching, resulting in no output and very low quiescent input current. The converter is inhibited when a TTL compatible low (≤0.8 V) is applied to the inhibit pin. The unit is enabled when the pin, which is internally connected to a pull-up resistor, is left unconnected or is connected to an open-collector gate. The open circuit output voltage associated with the inhibit pin is 9 to 11 V. In the inhibit mode, a maximum of 8 mA must be sunk from the inhibit pin. B2-47 MHD SERIES 20 WATT DC/DC CONVERTERS ABSOLUTE MAXIMUM RATINGS TYPICAL CHARACTERISTICS SYNC AND INHIBIT Input Voltage • 16 to 40 V Output Power • 15 to 20 watts depending on model Lead Soldering Temperature (10 sec per lead) • 300°C Storage Temperature Range (Case) • –65°C to +150°C Sync (500 to 675 kHz) • Duty cycle 40% min, 60% max • Logic low 0.8 V max, 0.0 V min • Logic high 4.0 V min, 10 V max • Referenced to input common • If not used, connect to input common Inhibit: TTL Open Collector • Logic low (output disabled) Logic low voltage ≤0.8 V Inhibit pin current 8.0 mA max • Referenced to input common • Logic high (output enabled) Open collector RECOMMENDED OPERATING CONDITIONS Input Voltage Range • 16 to 40 VDC continuous • 50 V for up to 50 msec transient Case Operating Temperature (Tc) • –55°C to +125°C Full power • –55°C to +135°C Absolute Derating Output Power/Current • Linearly from 100% at 125°C to 0% at 135° C Output Voltage Temperature Coefficient • 100 ppm/°C typical Input to Output Capacitance • 50 pF typical Current Limit • 115% of full load typical Isolation • 100 megohm minimum at 500 V Audio Rejection • 50 dB typical Conversion Frequency • Free run mode 625 kHz typical 550 kHz. min, 650 kHz max • External sync range 500 to 675 kHz Inhibit Pin Voltage (unit enabled) • 9 to 11 V Electrical Characteristics:25C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified. SINGLE OUTPUT MODELS MHD2805S MHD2815S MHD2818S MIN TYP MAX 17.82 18.00 18.18 0 — 1.11 VIN = 16 to 40 VDC 0 — 15 0 — 20 0 — 20 0 — 20 10 kHz – 2 MHz — 35 50 — 25 40 — 25 40 — — 40 Tc = –55°C TO +125°C Vin = 16 to 40 VDC Tc = –55°C TO +125°C NO LOAD TO FULL Tc = –55°C TO +125°C CONTINUOUS TRANSIENT 50 ms — — — — — 16 — 50 10 15 5 15 28 — 90 50 50 50 50 40 50 — — — — — 16 — 40 10 15 5 15 28 — 90 50 50 50 50 40 50 — — — — — 16 — 40 10 15 5 15 28 — 90 50 50 50 50 40 50 — — — — — 16 — — — — — — 28 — 90 50 50 50 50 40 50 NO LOAD1 FULL LOAD INHIBITED1 10 kHz – 10 MHz Tc = –55°C TO +125°C — — — 35 0.70 7 75 — 8 — — — 35 0.87 7 75 — 8 — — — 35 0.85 7 75 — 8 — — — — — — 75 — 8 mA A mA — 76 20 78 50 — — 80 20 83 50 — — 81 20 84 50 — — 81 — — 50 — mA p-p % SHORT CIRCUIT POWER DISSIPATION RECOVERY1, 3 50% – 100% – 50% 10% – 100% 100% – 10% 50% – 100% – 50% 10% – 100% 100% – 10% 16 – 40 – 16 VDC — — — — — — — — — 1.4 ±200 –400 +350 60 60 200 10 5 ±300 –600 +600 200 600 600 — — — — — — — — — 1.4 ±250 –600 +500 60 150 250 10 5 ±400 –1000 +750 200 300 500 — — — — — — — — — 1.4 ±350 –800 +600 60 250 250 10 5 ±500 –1200 +1000 200 500 500 — — — — — — — — — — — — — — — — 10 5 ±600 — — 200 — — A ms TRANSIENT5 RECOVERY4 — — ±200 ±300 — 300 — — ±400 ±500 — 300 — — ±500 ±600 — 300 — — — — ±600 300 mV pk µs DELAY OVERSHOOT FULL LOAD NO LOAD — 1.4 5 — 1.4 5 — 1.4 5 — — 5 ms — — 0 50 50 250 — — 0 120 120 600 — — 0 150 150 750 — — — — 180 — mV pk LOAD REGULATION INPUT VOLTAGE1 NO LOAD TO FULL INPUT CURRENT INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT3 SHORT CIRCUIT TO FULL LOAD STEP LOAD RESP. TRANSIENT RECOVERY4 STEP LINE RESP. START-UP1 TYP MAX 5.00 5.05 — 3 MIN TYP MAX 14.85 15.00 15.15 0 — 1.33 VIN = 16 to 40 VDC VOLTAGE LINE REGULATION2 MIN 4.95 0 MHD2812S OUTPUT POWER1 OUTPUT RIPPLE CONDITION MIN TYP MAX 11.88 12.00 12.12 0 — 1.67 PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT1 Notes 1. Tc = –55°C to +125°C 2. Operation is limited below 16V (see Figure 15). 3. Indefinite short circuit protection not guaranteed above 125°C case. B2-48 UNITS VDC A W mV p mV mV VDC V mV pk µs 4. Recovery time is measured from application of the transient to point at which Vout is within 1% of final value. 5. Transition time ≥ 10 µs. MHD SERIES 20 WATT DC/DC CONVERTERS Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified. DUAL OUTPUT MODELS PARAMETER CONDITIONS OUTPUT VOLTAGE1 +VOUT MHD2805D MIN TYP MAX 4.95 5.00 5.05 MHD2812D MIN TYP MAX 11.88 12.00 12.12 MHD2815D MIN TYP MAX 14.85 15.00 15.15 –VOUT 4.925 OUTPUT CURRENT1,2 VIN = 16 TO 40 VDC OUTPUT POWER1,2 VIN = 16 TO 40 VDC OUTPUT RIPPLE 10 kHz - 2 MHz 5.00 5.075 11.82 0.30 — 3.0 0 — 15 UNITS VDC 12.00 12.18 14.77 15.00 15.23 0.13 — 1.25 0.10 — 1.00 A 0 — 15 0 — 15 W — 20 50 — 30 80 — 25 80 VOLTAGE +/– VOUT Tc = –55°C TO +125°C — 40 80 — 40 120 — 40 120 LINE REGULATION3 Tc = –55°C +VOUT — 10 50 — 10 50 — 10 50 VIN = 16 TO 40 VDC TO +125°C –VOUT — 50 100 — 50 150 — 50 180 LOAD REGULATION Tc = –55°C +VOUT — 5 50 — 15 50 — 15 50 NO LOAD TO FULL TO +125°C –VOUT — 25 100 — 30 150 — 30 180 mV p-p mV mV CROSS REGULATION SEE NOTE 4 — 7 12 — 4 8.3 — 3 8 EFFECT ON –VOUT SEE NOTE5 — 4 6 — 4 6 — 4 6 INPUT VOLTAGE1 NO LOAD TO FULL INPUT CURRENT CONTINUOUS TRANSIENT 50 ms NO LOAD1 FULL LOAD INHIBITED1 16 0 — — — 28 — 35 0.70 7 40 50 75 — 8 16 0 — — — 28 — 50 0.88 7 40 50 75 — 8 16 0 — — — 28 — 50 0.86 7 40 50 75 — 8 VDC V mA A mA 10 kHz - 10 MHz — 76 15 78 50 — — 79 20 81 50 — — 80 20 83 50 — mA p-p % — — — 1.4 10 5.0 — — — 1.4 10 5.0 — — — 1.4 10 5.0 W ms INPUT RIPPLE CURRENT1 EFFICIENCY LOAD FAULT6 STEP LOAD RESPONSE ± VOUT STEP LINE RESPONSE ± VOUT START–UP POWER DISSIPATION SHORT CIRCUIT RECOVERY1, 7 TRANSIENT 50 – 100 – 50% % — ±200 ±300 — ±150 ±300 — ±200 ±400 10 – 100 –10% RECOVERY7 — ±400 ±600 — ±200 ±400 — ±300 ±500 50 – 100 – 50% 10 – 100 – 10% 16 – 40 – 16 VIN TRANSIENT8 — — 100 400 200 600 — — 100 100 200 200 — — 100 200 200 250 µs — ±200 ±400 — ±200 ±400 — ±400 ±500 mV pk RECOVERY7 DELAY — — — 1.4 300 5 — — — 1.4 300 5 — — — 1.4 300 5 µs ms OVERSHOOT — 0 50 — 0 120 — 0 150 NO LOAD — 50 250 — 120 600 — 150 750 Notes 1. Tc = –55°C to +125°C. 2. Up to 90% of the total output current/power is available from either output The minimum load on the positive output is 10% of full load. 3. Operation is limited below 16 V (see Figure 15). 4. Effect on the negative output under the following conditions: +Pout 20% to 80%; –Pout 80% to 20% 5. Effect on the negative output under the following conditions: +Pout 50%; –Pout 10% to 50% mV pk mV pk 6. Indefinite short circuit protection not guaranteed above 125°C case. 7. Recovery time is measured from application of the transient to point at which Vout is within 1% of final value. 8. Transition time ≥ 10 µs. B2-49 MHD SERIES 20 WATT DC/DC CONVERTERS PIN OUT Pin 1 2 3 4 5 6 7 8 9 10 Single Output Positive Input Inhibit No Connection Output Common Positive Output Case Ground Case Ground Case Ground Sync Input Input Common Dual Output Positive Input Inhibit Positive Output Output Common Negative Output Case Ground Case Ground Case Ground Sync Input Input Common Dot on top of cover indicates pin one. 1 2 3 4 10 9 8 7 6 Dotted line outlines flanged package option. See Section B8, cases H2 and K3 for dimensions. FIGURE 1: PIN OUT MODEL NUMBERING KEY MHD 28 12 S F / 883 Base Model Input Voltage Output Voltage Number of Outputs (S = single, D = dual) Case Option (Non-flanged case has no designator in this position) Screening (Standard screening has no designator in this position.) SMD NUMBERS STANDARD MICROCIRCUIT DRAWING (SMD) MHD SIMILAR MODEL NUMBER NON-FLANGED CASE 5962–9465501HXC 5962–9465601HXC 5962–9465701HXC 5962–9465801HXC 5962–9465901HXC 5962–9466001HXC 5962–9466101HXC MHD2805S/883 MHD2812S/883 MHD2815S/883 MHD2818S/883 MHD2805D/883 MHD2812D/883 MHD2815D/883 FLANGED CASE 5962–9465501HZC 5962–9465601HZC 5962–9465701HZC 5962–9465801HZC 5962–9465901HZC 5962–9466001HZC 5962–9466101HZC MHD2805SF/883 MHD2812SF/883 MHD2815SF/883 MHD2818SF/883 MHD2805DF/883 MHD2812DF/883 MHD2815DF/883 For exact specifications for an SMD product, refer to the SMD drawing. See Section A3, SMDs, for more information. B2-50 5 BOTTOM VIEW MHD FLANGED AND NON-FLANGED MHD SERIES 20 WATT DC/DC CONVERTERS Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, free run, unless otherwise specified. 85 16V Efficiency (%) Efficiency (%) 80 75 28V 70 40V 65 60 5 87 80 16V 75 28V 70 40V 65 10 60 15 16V 82 Efficiency (%) 85 28V 77 40V 72 67 5 10 15 62 20 5 10 15 20 Output Power (Watts) Output Power (Watts) Output Power (Watts) MHD2805S Efficiency MHD2812S Efficiency MHD2815S Efficiency FIGURE 2 FIGURE 3 FIGURE 4 90 85 0 16V 28V 75 40V 70 16V 80 28V 75 40V 70 65 60 Attenuation (dB) 85 Efficiency (%) 5 10 65 15 5 10 15 20 40 60 80 100 0.1 1 10 100 Output Power (Watts) Output Power (Watts) Frequency (kHz) MHD2812D Efficiency MHD2815D Efficiency MHD Series Audio Rejection FIGURE 5 FIGURE 6 200mV/div 100 mV/div 7.5 W to 15 W 1.5 W to 15 W 20 V/div 15 W to 1.5 W 15 W to 7.5 W FIGURE 7 20 mV/div Efficiency (%) 80 Vin Vout 50µs/div 10% to 100% to 10% 50µs/div (16 TO 40V) MHD2805S Step Load Response MHD2805S Step Load Response MHD2805S Step Line Response FIGURE 8 FIGURE 9 FIGURE 10 50µs/div 50% to 100% to 50% B2-51 MHD SERIES 20 WATT DC/DC CONVERTERS –Pout = 10 W Vin 20 mV/div 100 mV/div 1 V/div 20 V/div 10 W to 5 W 20 V/div Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, free run, unless otherwise specified. Vout Vin +Vout –Vout 5 W to 10 W 500µs/div 50µs/div 25% to 50% to 25% 50ms/div 16 TO 40V MHD2805S Turn On Into No Load MHD2815D +Vout Step Load Response MHD2815D Step Line Response FIGURE 11 FIGURE 12 FIGURE 13 Input Voltage (Volts) 5 V/div 20 V/div 16.0 Vin +Vout –Vout 15.5 15.0 14.5 14.0 13.5 13.0 200µs/div MHD2815D Turn On Into No Load FIGURE 14 B2-52 9 12 15 Output Power (Watts) Low Line Dropout vs. Load FIGURE 15 21222-001-DTS Rev A DQ# 1008 All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. MHD Series is a trademark of Interpoint. Copyright © 1994 - 1999 Interpoint. All rights reserved. CASES Dot on top of case indicates pin one CASE H BOTTOM VIEW See Figures 29 – 34 for pin configurations. 1.125 max (28.58) 2.125 max (53.98) CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. CASE H Materials Header Cold Rolled Steel/Nickel/Gold cases H1 and H2 Cold Rolled Steel/Nickel/Tin cases H3, H4, and H5 Cover Kovar/Nickel cases H1 and H2 Cold Rolled Steel/Nickel/Tin cases H3, H4, and H5 Pins #52 alloy ceramic seal case H1 case H2 (except MHV Series Single and Dual) compression glass seal MHV Series Single and Dual case H3, H4, H5 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified FIGURE 28: CASE H MAXIMUM DIMENSIONS BOTTOM VIEW CASE H1 FMC EMI Filter: Screening – Standard, ES, or 883 SFMC EMI Filter: Screening – Space Standard, H, or K Seam Seal Squared corner and dot on top of case indicate pin one. 0.040 dia (1.02) 1.110 (28.19) 0.955 (24.26) 1 2 3 0.555 (14.1) 5 4 0.155 (3.94) 2.090 (53.01) 1.845 (46.86) 0.245 (6.22) 0.000 0.25 ±0.03 (6.4 ±0.8) 0.000 0.400 max. (10.16) 0.000 FIGURE 29: CASE H1 Note: Although every effort has been made to render the case drawings at actual size, variations in the printing process may cause some distortion. Please refer to the numerical dimensions for accuracy. B8-17 CASES CASE H BOTTOM VIEW CASE H2 MTR Series Single, MHV Series Single and Dual, and MHD Series: Screening – Standard, ES, or 883 MTR Series Dual: Screening – 883 SMTR Series Single and Dual: Screening – Space Standard, H, or K Platform Bathtub Squared corner and dot on top of case indicate pin one. Seam Seal 1.110 (28.19) 0.955 (24.26) 1 2 3 4 5 10 9 8 7 1.045 (26.54) 1.445 (36.70) MHV Series Single and Dual, MHD Series, MTR Series Dual (883), and SMTR Series Dual 0.645 (16.38) All other H2 cases 0.245 (6.22) 0.040 dia (1.02) MHV Series 0.040 dia (1.02) 6 0.155 (3.94) 2.090 (53.01) 1.845 (46.86) 0.000 0.25 (6.4) 0.000 0.400 max. (10.16) 0.25 (6.4) 0.000 0.400 max. (10.16) 0.000 Squared corner and dot on top of case indicate pin one. 1.110 (28.19) 0.955 (24.26) 1 2 3 4 5 10 9 8 7 0.245 (6.22) 0.645 (16.38) 1.045 (26.54) 1.445 (36.70) MTR Series Single SMTR SeriesSingle 6 0.155 (3.94) FIGURE 30: CASE H2 B8-18 2.090 (53.01) 1.845 (46.86) 0.000 0.000 CASE K CASES Dot on top of case indicates pin one CASE K BOTTOM VIEW See Figures 42 - 48 for pin configuration 1.125 max (28.58) 2.910 max (73.91) Flange Thickness: Cases K1, K2, K3 and MLP Series (K5) 0.060 (1.52) Cases K4, K5 (except MLP Series), K6, K7, and K8 0.067 +0.005/-0.007 (1.70 +0.13/-0.8) Materials Header Case K1 - K3 Cold Rolled Steel/Nickel/Gold Cases K4 - K8 Cold Rolled Steel/Nickel/Tin Cover Case K1 - K3 Kovar/Nickel Case K4 - K8 Cold Rolled Steel/Nickel/Tin Pins #52 alloy (all cases) Case K1, K2, and K3 (except MHV Series Single and Dual) ceramic seal Cases K4 - K8 and MHV Series Single and Dual (K3) compression glass seal Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.2) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. FIGURE 41: CASE K MAXIMUM DIMENSIONS B8-26 CASES CASE K BOTTOM VIEW CASE K3 Flanged cases: Designator required in Case Option position of model number. MTR Series Single, MHV Series Single and Dual, MHD Series: Screening – Standard, ES, or 883 MTR Series Dual: Screening – 883 SMTR Series: Screening – Space Standard, H, or K Platform Dot on top of case indicates pin one Seam Seal 1.110 (28.19) 0.955 (24.26) 1 0.040 dia (1.02) 2 3 4 5 10 9 8 7 0.245 (6.22) 0.645 (16.38) 1.045 (26.54) 1.445 (36.70) MHD Series, MTR Series Dual (883), and SMTR Series Dual 0.555 (14.1) 6 0.155 (3.94) Platform Seam Seal 2.320 (58.93) 1.845 (46.86) 0.000 – 0.230 (5.84) 0.25 ±0.03 (6.4 ±0.8) 0.000 0.400 max. (10.16) 0.000 Dot on top of case indicates pin one 1.110 (28.19) 0.955 (24.26) 1 0.040 dia (1.02) 2 3 4 5 MTR Series Single and SMTR Series Single 10 9 8 7 0.245 (6.22) 0.645 (16.38) 1.045 (26.54) 1.445 (36.70) 0.555 (14.1) 6 0.155 (3.94) 2.320 (58.93) 1.845 (46.86) 0.000 0.230 (5.84) 0.25 ±0.03 (6.4 ±0.8) 0.000 0.400 max. (10.16) 0.000 Bathtub Dot on top of case indicates pin one Seam Seal 1.110 (28.19) 0.955 (24.26) 1 0.040 dia (1.02) 2 3 4 5 MHV Series Single and Dual 10 9 8 7 0.245 (6.22) 0.645 (16.38) 1.045 (26.54) 1.445 (36.70) 0.555 (14.1) 6 0.155 (3.94) FIGURE 44: CASE K3 B8-28 2.320 (58.93) 1.845 (46.86) 0.000 0.230 (5.84) 0.25 ±0.03 (6.4 ±0.8) 0.000 0.400 max. (10.16) 0.000 QA SCREENING 125°C PRODUCTS 125°C PRODUCTS TEST (125°C Products) STANDARD /ES /883 (Class H)* PRE-CAP INSPECTION Method 2017, 2032 yes yes yes TEMPERATURE CYCLE (10 times) Method 1010, Cond. C, -65°C to 150°C Method 1010, Cond. B, -55°C to 125°C no no no yes yes no CONSTANT ACCELERATION Method 2001, 3000 g Method 2001, 500 g no no no yes yes no BURN-IN Method 1015, 160 hours at 125°C 96 hours at 125°C case (typical) no no no yes yes no FINAL ELECTRICAL TEST MIL-PRF-38534, Group A Subgroups 1 through 6: -55°C, +25°C, +125°C Subgroups 1 and 4: +25°C case no yes no yes yes no HERMETICITY TESTING Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C Gross Leak, Dip (1 x 10-3) no no yes yes yes no yes yes no FINAL VISUAL INSPECTION Method 2009 yes yes yes Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. *883 products are built with element evaluated components and are 100% tested and guaranteed over the full military temperature range of –55°C to +125°C. Applies to the following products MOR Series MHD Series MFLHP Series MHV Series MFL Series MHF+ Series MHP Series MHF Series** MTR Series MGA Series MQO Series** MSA Series MGH Series MCH Series FM-704A EMI Filter FMD**/FME EMI Filter FMC EMI Filter FMH EMI Filter FMGA EMI Filter FMSA EMI Filter HUM Modules** LCM Modules** LIM Modules **MFLHP Series, MQO Series, MHF Series, FMD EMI Filters, Hum Modules, and LCM Modules do not offer ‘883” screening. C2-10