HT92632/HT92652 High Precision OPAMP Features General Description • Wide Operating Voltage The H T92632/H T92652 family of precis ion operational amplifiers offers the benefits of low offset voltage and low offset drift. They are unity gain stable, have low 1/f noise as well as good PSRR and CMRR characteristics. The devices also provide full rail-to-rail input and output operation. The HT92632 has a gain bandwidth product of 300kHz while the HT92652 has a gain bandwidth product of 1.5MHz. • Low input offset voltage • Low Quiescent Current • Unity Gain Stable • Rail to Rail input and output operation • -40˚C to +85˚C Operating Temperature Range • Dual amplifiers per package These characteristics along with their single supply operation and low power consumption features provide a range of low offset voltage operational amplifiers suitable for use in a wide range of applications, especially for portable devices and battery powered equipment. With regard to packaging, both devices are supplied in 8-pin MSOP/SOP package formats. • Package types: 8-pin MSOP/SOP Applications • Portable Test Equipment • Medical Instrument • Sensor Applications • Temperature Measurements • Battery Powered Systems Block Diagram VDD 2OUT 1OUT 1IN- - - 2IN- 1IN+ + + 2IN+ VSS Pin Assignment 1OUT 1 8 1IN- 2 7 2OUT 1IN+ 3 6 2IN- 4 5 2IN+ VSS VDD HT92632/HT92652 8 SOP-A/MSOP-A Rev. 1.00 1 October 11, 2017 HT92632/HT92652 Pin Description Pin Number Pin Name Description 1 1OUT 2 1IN- Inverting Input – OPA1 3 1IN+ Non-inverting Input – OPA1 4 VSS Negative Power Supply 5 2IN+ Non-inverting Input – OPA2 6 2IN- Inverting Input – OPA2 7 2OUT Output – OPA2 8 VDD Positive Power Supply Output – OPA1 Selection Table Device Name Amplifiers Operating Gain Bandwidth Voltage (Typ.) HT92632 2 2.0V~5.5V 300kHz HT92652 2 2.0V~5.5V 1.5MHz ΔVOS/ΔTA (Typ.) Slew Rate (Typ.) Package Type 15μV 50nV 0.15V/μs 8SOP/MSOP 10μV(Max.) 50nV(Max.) 0.5V/μs 8SOP/MSOP VOS (Typ.) Absolute Maximum Ratings Supply Voltage..................................VSS-0.3V to 6.0V IOL Total.............................................................. 80mA Input Voltage............................ VSS-0.3V to VDD+0.3V IOH Total............................................................. -80mA Storage Temperature........................... -50°C to 150°C Total Power Dissipation.................................. 500mW Operating Temperature......................... -40°C to 85°C Note: These are stress ratings only. Stresses exceeding the range specified under “Absolute Maximum Ratings” may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Rev. 1.00 2 October 11, 2017 HT92632/HT92652 Electrical Characteristics HT92632 Unless otherwise indicated, TA=25°C, VDD=2.0V to 5.5V, VSS=GND, VCM=VDD/3, VOUT≈VDD/2, VL=VDD/2, RL=100kΩ to VL and CL=30pF Symbol Parameter Test Conditions VDD Conditions Min Typ Max Units VDD Supply Voltage — TA=25°C 2.0 — 5.5 V VOS Input Offset Voltage — TA=25°C — 15 40 μV ΔVOS/ΔTA Drift with Temperature — TA=-40°C~125°C -50 — +50 nV/°C IOS Input Offset Current — TA=25°C — 100 — pA IB Input Bias Current — TA=25°C — 50 — pA VCML Input Common Mode Range Low — — — — VSS-0.1 V VCMH Input Common Mode Range High — — VDD+0.1 — — V VOL Minimum Output Voltage Swing — RL=10kΩ to VL, G=+2, 0.5V input overdrive VSS VOH Maximum Output Voltage Swing — RL=10kΩ to VL, G=+2, 0.5V input overdrive AOL Large Signal DC Open Loop Gain — VOUT=0.3V~VDD-0.3V GBW Gain Bandwidth Product — PM Phase Margin — CMRR Common Mode Rejection Ratio — PSRR Power Supply Rejection Ratio — IQ Quiescent Current/Amplifier — SR Slew Rate — ISC Output Short Circuit Current Eni Input Noise Voltage — eni Input Noise Voltage Density — — VSS+35 VSS+80 mV VDD-80 VDD-35 VDD mV 100 130 — dB — 300 — kHz — 70 — degree 100 120 — dB 100 120 — dB 10 30 40 μA — — 0.15 — V/μs 3V — — ±6 — mA 5V — — ±21 — mA f=0.1Hz to 10Hz — 1 — μVP-P — F<2kHz — 50 — nV/ Hz — 120 — μs VCM=-0.1V~VDD+0.1V — IOUT=0 TOOR Output Overdrive Recovery Time — G=-10, ±0.5V input overdrive to VDD/2, VIN 50% point to VOUT 90% TOCS Offset Correction Settling Time — G=+1, VIN step of 2V, VOS within 100uV of its final value — 100 — μs Tstart Start Up Time — G=+1, 0.1% VOUT settling — 2 — ms Rev. 1.00 3 October 11, 2017 HT92632/HT92652 HT92652 Unless otherwise indicated, TA=25°C, VDD=2.0V to 5.5V, VSS=GND, VCM=VDD/3, VOUT≈VDD/2, VL=VDD/2, RL=20kΩ to VL and CL=60pF Symbol Test Conditions Parameter VDD Conditions Min Typ Max Units V VDD Supply Voltage — TA= 25°C 2.0 — 5.5 VOS Input Offset Voltage — TA= 25°C -10 — +10 μV ΔVOS/ΔTA Drift with Temperature — TA=-40°C~125°C -50 — +50 nV/°C VCML Input Common Mode Range Low — — — — VSS-0.1 V VCMH Input Common Mode Range High — — VDD+0.1 — — V VOL Minimum Output Voltage Swing — RL=10kΩ to VL, G=+2, 0.5V input overdrive VOH Maximum Output Voltage Swing — RL=10kΩ to VL, G=+2, 0.5V input overdrive AOL Large Signal DC Open Loop Gain — VOUT=0.3V~VDD-0.3V GBW Gain Bandwidth Product — — PM Phase Margin — — CMRR Common Mode Rejection Ratio — PSRR Power Supply Rejection Ratio — IQ Quiescent Current/Amplifier — SR Slew Rate — ISC Output Short Circuit Current Eni Input Noise Voltage — eni Input Noise Voltage Density VSS+35 VSS+80 mV VDD-80 VDD-35 VDD mV 100 130 — dB 1.3 1.5 — MHz — 70 — degree 100 120 — dB 100 120 — dB — — 500 μA — — 0.5 — V/μs 3V — — ±7 — mA 5V — — ±22 — mA f=0.1Hz to 10Hz — 1 — μVP-P — F<2.5kHz — 120 — nV/ Hz — 120 — μs VCM=-0.1V~VDD+0.1V — IOUT=0 VSS TOOR Output Overdrive Recovery Time — G=-100, ±0.5V input overdrive to VDD/2, VIN 50% point to VOUT 90% TOCS Offset Correction Settling Time — G=+1, VIN step of 2V, VOS within 100uV of its final value — 300 — μs Tstart Start Up Time — G=+1, 0.1% VOUT settling — 2 — ms Application Circuits RG2 VIN2 RG1 VIN1 RF VDD RX RZ + VOUT RY 1 , R = total resistance at the inverting input. 1 + 1 + 1 VINRG1 RG2 RF 1 RVIN+ = + RZ, RVIN+ = total resistance at the non-inverting input, RVIN+ = RVIN-. 1 + 1 R R RVIN- = X Rev. 1.00 Y 4 October 11, 2017 HT92632/HT92652 Package Information Note that the package information provided here is for consultation purposes only. As this information may be updated at regular intervals users are reminded to consult the Holtek website for the latest version of the Package/ Carton Information. Additional supplementary information with regard to packaging is listed below. Click on the relevant section to be transferred to the relevant website page. • Package Information (include Outline Dimensions, Product Tape and Reel Specifications) • The Operation Instruction of Packing Materials • Carton information Rev. 1.00 5 October 11, 2017 HT92632/HT92652 8-pin SOP (150mil) Outline Dimensions Symbol Dimensions in inch Min. Nom. Max. A — 0.236 BSC — B — 0.154 BSC — 0.020 C 0.012 — C′ — 0.193 BSC — D — — 0.069 E — 0.050 BSC — F 0.004 — 0.010 G 0.016 — 0.050 H 0.004 — 0.010 α 0° — 8° Symbol Rev. 1.00 Dimensions in mm Min. Nom. Max. A — 6.00 BSC — B — 3.90 BSC — C 0.31 — 0.51 C′ — 4.90 BSC — D — — 1.75 E — 1.27 BSC — F 0.10 — 0.25 G 0.40 — 1.27 H 0.10 — 0.25 α 0° — 8° 6 October 11, 2017 HT92632/HT92652 8-pin MSOP Outline Dimensions Symbol Dimensions in inch Min. Nom. Max. A — — 0.043 A1 0.000 — 0.006 A2 0.030 0.033 0.037 B 0.009 — 0.015 C 0.003 — 0.009 D — 0.118 BSC — E — 0.193 BSC — E1 — 0.118 BSC — e — 0.026 BSC — L 0.016 0.024 0.031 L1 — 0.037 BSC — y — 0.004 — θ 0° — 8° Symbol Rev. 1.00 Dimensions in mm Min. Nom. Max. A — — 1.10 A1 0.00 — 0.15 A2 0.75 0.85 0.95 B 0.22 — 0.38 C 0.08 — 0.23 D — 3.00 BSC — E — 4.90 BSC — E1 — 3.00 BSC — e — 0.65 BSC — L 0.40 0.60 0.80 L1 — 0.95 BSC — y — 0.10 — θ 0° — 8° 7 October 11, 2017 HT92632/HT92652 Copyright© 2017 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek's products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com/en/. Rev. 1.00 8 October 11, 2017