AFCT-5760Z and AFCT-5765Z Families of Small Form Factor Pluggable (SFP) Optical Transceivers for Single-Mode OC3/STM-1 with Optional DMI Part of the Avago Technologies METRAK Family Data Sheet Description The AFCT-576xZ family of SFP optical transceivers for OC3 offers the customer a range of design options, including optional DMI (further described later), extended or industrial temperature ranges, and standard push-button or or bail delatch. The AFCT-5765Z family targets applications requiring DMI features, and the AFCT-5760Z family is streamlined for those applications where DMI features are not needed. Throughout this document, AFCT-576xZ will refer collectively to the entire product family encompassing this range of product features. Part Number Options The AFCT-576xZ ucts: With DMI Part Number AFCT-5765LZ AFCT-5765PZ AFCT-5765ALZ AFCT-5765APZ AFCT-5765TLZ AFCT-5765TPZ AFCT-5765ATLZ AFCT-5765ATPZ family consists of the following prod- Temperature Extended* Extended* Industrial* Industrial* Extended* Extended* Industrial* Industrial* Design Standard Bail Standard Bail Standard Bail Standard Bail Distance SR (2km) SR SR SR IR (15km) IR IR IR Without DMI Part Number AFCT-5760LZ AFCT-5760PZ AFCT-5760ALZ AFCT-5760APZ AFCT-5760TLZ AFCT-5760TPZ AFCT-5760ATLZ AFCT-5760ATPZ Temperature Extended* Extended* Industrial* Industrial* Extended* Extended* Industrial* Industrial* Design Standard Bail Standard Bail Standard Bail Standard Bail Distance SR (2km) SR SR SR IR (15km) IR IR IR Features ROHS compliant Optional Digital Diagnostic Monitoring available * Extended Temperature Range is -10 to 85 degrees C Industrial Temperature Range is -40 to 85 degrees C - AFCT-5760Z family: without DMI - AFCT-5765Z family: with DMI Per SFF-8472, diagnostic features on AFCT-5765Z family enable Diagnostic Monitoring Interface for optical transceivers with real-time monitoring of: - Transmitted optical power - Received optical power - Laser bias current - Temperature - Supply voltage Compliant with SFF-8074i SFP transceiver specification Compliant with ITU-T G957 STM-1 I-1 (2 km), STM-1 S-1.1 (15 km) Compliant with Telcordia GR253 SR (2 km), IR-1 (15 km) Class 1 CDRH/IEC 825 eye safety compliant Operating case temperature range –10 °C to +85 °C (Extended) –40 °C to +85 °C (Industrial) Multitrate operation from 125 Mb/s to 155 Mb/s LC duplex fiber connector Manufactured in an ISO 9001 compliant facility Applications ATM switches and routers SONET/SDH switch infrastructure Broadband aggregation applications Metro edge switching Metro and access multi-service platforms Suitable for Fast Ethernet applications Related Products AFCT-5755Z family of OC12 SFP transceivers with DMI AFCT-5745L/P family of OC48 SFP transceivers with DMI General Features SFP MSA Compliance The AFCT-576xZ family of SFP optical transceivers are high performance, cost effective modules for serial optical data communications applications ranging from 125-155 Mbps. They are designed to provide SONET/SDH compliant connections for 155 Mbps at short and intermediate reach links. This includes specifications for the signal coding, optical fiber and connector types, optical and electrical transmitter characteristics, optical and electrical receiver characteristics, jitter characteristics, and compliance testing methodology for the aforementioned. These transceivers are qualified in accordance with GR-468-CORE. The product package is compliant with the SFP MSA with the LC connector option. The SFP MSA includes specifications for mechanical packaging and performance as well as dc, ac and control signal timing and performance. The transmitter section of the SR and IR transceivers incorporate a 1300nm Fabry Perot (FP) laser. For each device the receiver section uses an MOVPE grown planar PIN photodetector for low dark current and excellent responsivity. A positive-ECL logic interface simplifies interface to external circuitry. The receiver section contains an InGaAs/InP photo detector and a preamplifier mounted in an optical subassembly. This optical subassembly is coupled to a postamplifier/decision circuit on a circuit board. The power supply is 3.3 V dc. The High Speed I/O (HSIO) signal interface is a Low Voltage Differential type. It is ac coupled and terminated internally to the module. The internal termination is a 100 Ohm differential load. Installation The AFCT-576xZ can be installed in any SFF-8074i compliant Small Form Pluggable (SFP) port regardless of host equipment operating status. The module is hot-pluggable, allowing it to be installed while the host system is operating and online. Upon insertion, the transceiver housing makes initial contact with the host board SFP cage, mitigating potential damage due to electrostatic discharge (ESD). The AFCT-576xZ family of optical transceivers adds digital diagnostic monitoring to standard SFP functionality, enabling fault isolation, components monitoring and failure prediction capabilities. Optical Interface Light from Fiber Electrical Interface Receiver Photo-Detector Amplification & Quantization RD+ (Receive Data) RD- (Receive Data) Rx Loss Of Signal MOD-DEF2 (SDA) text Controller & Memory MOD-DEF1 (SCL) MOD-DEF0 Transmitter Light to Fiber Laser TX_DISABLE Laser Driver & Safety Circuit TD+ (Transmit Data) TD- (Transmit Data) TX_FAULT Figure 1. Transceiver Functional Diagram 2 Transmitter Section TX_FAULT The transmitter section includes a 1310 nm Fabry-Perot laser and a transmitter driver circuit. The driver circuit maintains a constant optical power level provided that the data pattern is valid for NRZ code. Connection to the transmitter is provided via a LC optical connector. A laser fault or a low VCC condition will activate the transmitter fault signal, TX_FAULT, and disable the laser. This signal is an open collector output (pull-up required on the host board); A low signal indicates normal laser operation and a high signal indicates a fault. The TX_FAULT will be latched high when a laser fault occurs and is cleared by toggling the TX_DISABLE input or power cycling the transceiver. The TX_FAULT is not latched for Low VCC. The transmitter fault condition can also be monitored via the two-wire serial interface (address A2, byte 110, bit 2). By default, TX_FAULT is set to trigger on hardware faults only. The transmitter has full IEC 825 and CDRH Class 1 eye safety. TX_DISABLE The transmitter output can be disabled by asserting pin 3, TX_DISABLE. A high signal asserts this function while a low signal allows normal laser operation. The transmitter output can also be disabled and monitored via the 2-wire serial interface. In the event of a transceiver fault, such as the activation of the eye safety circuit, toggling of the TX_DISABLE will reset the transmitter, as depicted in Figure 2. 1 µH 3.3 V 10 µF 0.1 µF 1 µH 3.3 V VCC,T SFP MODULE 0.1 µF 4.7 K to 10 KΩ 4.7 K to 10 KΩ Tx_DISABLE Tx_FAULT Tx_FAULT VREFR VREFR SO+ 50 Ω TD+ SO– 50 Ω TD– TX GND TX[0:9] TBC EWRAP PROTOCOL IC RBC Rx_RATE TBC EWRAP 10 µF RBC Rx_RATE REFCLK SI+ 100 Ω SI– RD+ 50 Ω RD– Rx_LOS RX GND MOD_DEF2 MOD_DEF1 MOD_DEF0 GPIO(X) GPIO(X) GP14 4.7 K to 10 KΩ 4.7 K to 10 KΩ 4.7 K to 10 KΩ 3.3 V Figure 2. Typical Application Configuration 3 0.01 µF VCC,R 50 Ω 0.1 µF 50 Ω Rx_LOS REFCLK LASER DRIVER & SAFETY CIRCUITRY 100 Ω VCC,R 4.7 K to 10 KΩ RX[0:9] 0.01 µF 0.01 µF 0.01 µF AMPLIFICATION & QUANTIZATION 50 Ω VCC,R EEPROM Receiver Section The receiver section for the AFCT-576xZ contains an InGaAs/InP photo detector and a preamplifier mounted in an optical subassembly. This optical subassembly is coupled to a post amplifier/decision circuit on a circuit board. The design of the optical subassembly provides better than 12 dB Optical Return Loss (ORL). Connection to the receiver is provided via a LC optical connector. RX_LOS The receiver section contains a loss of signal (RX_LOS) circuit to indicate when the optical input signal power is insufficient for SONET/SDH compliance. A high signal indicates loss of modulated signal, indicating link failure such as a broken fiber or a failed transmitter. RX_LOS can be also be monitored via the two-wire serial (address A2, byte 110, bit 1). Functional Data I/O Avago’s AFCT-576xZ transceiver is designed to accept industry standard differential signals. The transceiver provides an AC-coupled, internally terminated data interface. Bias resistors and coupling capacitors have been included within the module to reduce the number of components required on the customer’s board. Figure 2 illustrates the recommended interface circuit. Digital Diagnostic Interface and Serial Identification The AFCT-576xZ family complies with the SFF-8074i specification, which defines the module’s serial identification protocol to use the 2-wire serial CMOS EEPROM protocol of the ATMEL AT24C01A or similar. Standard SFP EEPROM bytes 0-255 are addressed per SFF-8074i at memory address 0xA0 (A0h). As an enhancement to the conventional SFP interface defined in SFF-8074i, the AFCT-5765Z is also compliant to SFF-8472 (the digital diagnostic interface for SFP). This enhancement adds digital diagnostic monitoring to standard SFP functionality, enabling failure prediction, fault isolation, and component monitoring capabilities. Using the 2-wire serial interface, the AFCT-5765Z provides real time access to transceiver internal supply voltage and temperature, transmitter output power, laser bias current and receiver average input power, allowing a host to predict system compliance issues. These five parameters are internally calibrated, per the MSA. New digital diagnostic information is accessed per SFF-8472 using EEPROM bytes 0-255 at memory address 0xA2 (A2h). The digital diagnostic interface also adds the ability to disable the transmitter (TX_DISABLE), monitor for Transmitter Faults (TX_FAULT) and monitor for Receiver Loss of Signal (RX_LOS). Contents of the MSA-compliant serial ID memory are shown in Tables 3 to 7. The SFF-8074i and SFF-8472 specifications are available from the SFF Committee at http://www.sffcommittee.org. The I2C accessible memory page address 0xB0 is used internally by SFP for the test and diagnostic purposes and it is reserved. Predictive Failure Identification The diagnostic information allows the host system to identify potential link problems. Once identified, a failover technique can be used to isolate and replace suspect devices before system uptime is impacted. Compliance Prediction The real-time diagnostic parameters can be monitored to alert the system when operating limits are exceeded and compliance cannot be ensured. Fault Isolation The diagnostic information can allow the host to pinpoint the location of a link problem and accelerate system servicing and minimize downtime. Component Monitoring As part of the host system monitoring, the real time diagnostic information can be combined with system level monitoring to ensure system reliability. Application Support 1 µH VCCT 0.1 µF 1 µH VCCR 3.3 V 0.1 µF SFP MODULE 10 µF HOST BOARD Figure 3. MSA required power supply filter 4 0.1 µF 10 µF An Evaluation Kit and Reference Designs are available to assist in evaluation of the AFCT-576xZ SFPs. Please contact your local Field Sales representative for availability and ordering details. Operating Temperature The AFCT-576xZ family is available in either Extended (-10 to +85°C) or Industrial (-40 to +85°C) temperature ranges. Power Supply Noise The AFCT-576xZ can withstand an injection of PSN on the VCC lines of 100 mV ac without a degradation in eye mask margin to 10% on the transmitter and a 1 dB sensitivity penalty on the receiver. This occurs when the product is used in conjunction with the MSA recommended power supply filter shown in Figure 3. Regulatory Compliance The transceiver regulatory compliance is provided in Table 1 as a figure of merit to assist the designer. The overall equipment design will determine the certification level. Table 1. Regulatory Compliance Feature Test Method Performance Electrostatic Discharge (ESD) to the Electrical Pins MIL-STD-883C Method 3015.4 JEDEC/EIA JESD22-A114-A Class 2 (2000 Volts) Electrostatic Discharge (ESD) to the Duplex LC Receptacle Bellcore GR1089-CORE 25 kV Air Discharge 10 Zaps at 8 kV (contact discharge) on the electrical faceplate on panel. Electromagnetic Interference (EMI) FCC Class B Applications with high SFP port counts are expected to be compliant; however, margins are dependent on customer board and chassis design. Immunity Variation of IEC 61000-4-3 No measurable effect from a 10 V/m field swept from 80 to 1000 MHz applied to the transceiver without a chassis enclosure. Eye Safety US FDA CDRH AEL Class 1 EN (IEC) 60825-1, 2, EN60950 Class 1 CDRH Accession Number: 9521220-137 TUV Certificate Number: 933/21205741/040 Component Recognition Underwriter’s Laboratories and Canadian Standards Association Joint Component Recognition for Information Technology Equipment Including Electrical Business Equipment UL file # E173874 ROHS Compliance 5 Reference to EU RoHS Directive 2002/95/EC Electrostatic Discharge (ESD) Caution There are two conditions in which immunity to ESD damage is important: The AFCT-576xZ contains no user-serviceable parts. Tampering with or modifying the performance of the AFCT576xZ will result in voided product warranty. It may also result in improper operation of the transceiver circuitry, and possible over-stress of the laser source. Device degradation or product failure may result. Connection of the AFCT-576xZ to a non-approved optical source, operating above the recommended absolute maximum conditions may be considered an act of modifying or manufacturing a laser product. The person(s) performing such an act is required by law to re-certify and re-identify the laser product under the provisions of U.S. 21 CF. The first condition is static discharge to the transceiver during handling such as when the transceiver is inserted into the transceiver port. To protect the transceiver, it is important to use normal ESD handling precautions including the use of grounded wrist straps, work benches, and floor mats in ESD controlled areas. The ESD sensitivity of the AFCT-576xZ is compatible with typical industry production environments. The second condition is static discharge to the exterior of the host equipment chassis after installation. To the extent that the duplex LC optical interface is exposed to the outside of the host equipment chassis, it may be subject to system-level ESD requirements. The ESD performance of the AFCT-576xZ exceeds typical industry standards. Table 1 documents ESD immunity to both of these conditions. Electromagnetic Interference (EMI) Most equipment designs using the AFCT-576xZ SFPs are subject to the requirements of the FCC in the United States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan. The metal housing and shielded design of the transceiver minimize EMI and provide excellent EMI performance. EMI Immunity The AFCT-576xZ transceivers have a shielded design to provide excellent immunity to radio frequency electromagnetic fields which may be present in some operating environments. Eye Safety The AFCT-576xZ transceivers provide Class 1 eye safety by design. Avago Technologies has tested the transceiver design for regulatory compliance, under normal operating conditions and under a single fault condition. See Table 1. Flammability The AFCT-576xZ family of SFPs is compliant to UL 94V-0. Customer Manufacturing Processes This module is pluggable and is not designed for aqueous wash, IR reflow, or wave soldering processes. 6 Handling Precautions The AFCT-576xZ can be damaged by current surges or overvoltage. Power supply transient precautions should be taken, and normal handling precautions for electrostatic sensitive devices should be taken. Optical Power Budget The worst-case Optical Power Budget (OPB) in dB for a fiber-optic link is determined by the difference between the minimum transmitter output optical power (dBm avg) and the lowest receiver sensitivity (dBm avg). This OPB provides the necessary optical signal range to establish a working fiber-optic link. The OPB is allocated for the fiber-optic cable length and the corresponding link penalties. For proper link performance, all penalties that affect the link performance must be accounted for within the link optical power budget. Process Plug This transceiver is supplied with a process plug for protection of the optical port within the LC connector receptacle. This process plug prevents contamination during handling, shipping and storage. It is made of a high-temperature, molded sealing material that can withstand +85 °C. LC SFP Cleaning Recommendations In the event of contamination of the optical ports, the recommended cleaning process is the use of forced nitrogen. If contamination is thought to have remained, the optical ports can be cleaned using a NTT international Cletop stick type (diam. 1.25 mm) and HFE7100 cleaning fluid. Table 2. Pin description Pin Name Function/Description 1 VeeT Transmitter Ground MSA Notes 2 TX Fault Transmitter Fault Indication Note 1 3 TX Disable Transmitter Disable - Module disables on high or open Note 2 4 MOD-DEF2 Module Definition 2 - Two wire serial ID interface Note 3 5 MOD-DEF1 Module Definition 1 - Two wire serial ID interface Note 3 6 MOD-DEF0 Module Definition 0 - Grounded in module Note 3 7 Rate Select Not Connected 8 LOS Loss of Signal 9 VeeR Receiver Ground 10 VeeR Receiver Ground 11 VeeR Receiver Ground 12 RD- Inverse Received Data Out Note 5 13 RD+ Received Data Out Note 5 14 VeeR Receiver Ground 15 VccR Receiver Power - 3.3 V ±5% Note 6 16 VccT Transmitter Power - 3.3 V ±5% Note 6 17 VeeT Transmitter Ground 18 TD+ Transmitter Data In Note 7 19 TD- Inverse Transmitter Data In Note 7 20 VeeT Transmitter Ground Note 4 Notes: 1. TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor on the host board. Pull up voltage between 2.0 V and VccT, R+0.3 V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V. By default, TX_FAULT is set to trigger on hardware faults only. 2. TX Disable input is used to shut down the laser output per the state table below with an external 4.7 - 10 K pull-up resistor. Low (0 - 0.8 V): Transmitter on Between (0.8 V and 2.0 V): Undefined High (2.0 - 3.465 V): Transmitter Disabled Open: Transmitter Disabled 3. MOD-DEF 0,1,2. These are the module definition pins. They should be pulled up with a 4.7 - 10 K resistor on the host board to a supply less than VccT +0.3 V or VccR+0.3 V. MOD-DEF 0 is grounded by the module to indicate that the module is present MOD-DEF 1 is clock line of two wire serial interface for optional serial ID MOD-DEF 2 is data line of two wire serial interface for optional serial ID 4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7K - 10 K resistor on the host board to a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V. 5. RD-/+: These are the differential receiver outputs. They are ac coupled 100 differential lines which should be terminated with 100 differential at the user SERDES. The ac coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 320 and 2000 mV differential (160 - 1000 mV single ended) when properly terminated. 6. VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.135 - 3.465 V at the SFP connector pin. The maximum supply current is 250 mA and the associated inrush current will be no more than 30 mA above steady state after 500 nanoseconds. 7. TD-/+: These are the differential transmitter inputs. They are ac coupled differential lines with 100 differential termination inside the module. The ac coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 - 2400 mV (250 - 1200 mV single ended), though it is recommended that values between 500 and 1200 mV differential (250 - 600 mV single ended) be used for best EMI performance. 7 Table 3. EEPROM Serial ID Memory Contents - Address A0h Byte Data #Decimal Hex Notes Byte Data #Decimal Hex 0 03 SFP physical device 27 20 54 20 1 04 SFP function defined by serial ID only 28 20 55 20 2 07 LC optical connector 29 20 56 30 3 00 30 20 57 30 4 Table 4 SONET Reach Specifier 31 20 58 31 5 Table 4 SONET Compliance Code 32 20 59 30 6 00 33 20 60 Table 4 7 00 34 20 61 Table 4 8 00 35 20 62 00 9 00 36 00 63 10 00 37 00 Hex Byte of Vendor OUI1 64 00 11 05 SONET Scrambled 38 17 Hex Byte of Vendor OUI1 65 1A Hardware SFP Tx_Disable, Tx_Fault & Rx_LOS 12 02 155 Mbit/sec nominal 39 bit rate 6A Hex Byte of Vendor OUI1 66 00 Upper Bit Rate Margin 13 00 40 41 A 67 00 Lower Bit Rate Margin 14 Table 4 Link length 9 μm in km 41 46 F 68-83 Vendor Specific Serial Number ASCII characters4 15 Table 4 Link length 9 μm in m 42 43 C 84-91 Vendor Date Code ASCII characters5 16 00 43 54 T 92 Table 4 17 00 44 2D - 93 Table 4 18 00 45 35 5 94 Table 4 19 00 46 37 7 95 20 41 A 47 36 6 96-127 21 56 V 48 Table 4 22 41 A 49 Table 4 23 47 G 50 Table 4 24 4F O 51 Table 4 25 20 52 Table 4 26 20 53 20 Notes Byte Data #Decimal Hex Checksum for Bytes 0-623 Checksum for Bytes 64-943 00 128-255 00 Notes: 1. The IEEE Organizationally Unique Identifier (OUI) assigned to Avago is 00-17-6A (3 bytes of hex). 2. Laser wavelength is represented in 16 unsigned bits. 3. Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment. 4. Addresses 68-83 specify the ASCII serial number and will vary on a per unit basis. 5. Addresses 84-91 specify the ASCII date code and will vary on a per date code basis. 8 Notes Vendor specific EEPROM Reserved Table 4a. Individual Identifiers AFCT-5760LZ AFCT-5760PZ AFCT-5760TLZ AFCT-5760TPZ Byte # Hex Notes Hex Notes Hex Notes Hex Notes 4 10 SR-1 10 SR-1 10 IR-1 10 IR-1 5 01 OC-3 SR-1 01 OC-3 SR-1 02 OC-3 IR-1 02 OC-3 IR-1 14 02 2 Km 02 2 Km 0F 15 Km 0F 15 Km 15 14 2000m 14 2000m 96 15000m 96 15000m 48 30 0 30 0 30 0 30 0 49 4C L 50 P 54 T 54 T 50 5A Z 5A Z 4C L 50 P 51 20 - 20 - 5A Z 5A Z 52 20 - 20 - 20 - 20 - 60 05 1310nm 05 1310nm 05 1310nm 05 1310nm 61 1E 1E 1E 1E 92 00 00 00 00 93 00 00 00 00 94 00 00 00 00 AFCT-5760ALZ AFCT-5760APZ AFCT-5760ATLZ AFCT-5760ATPZ Byte # Hex Notes Hex Notes Hex Notes Hex Notes 4 10 SR-1 10 SR-1 10 IR-1 10 IR-1 5 01 OC-3 SR-1 01 OC-3 SR-1 02 OC-3 IR-1 02 OC-3 IR-1 14 02 2 Km 02 2 Km 0F 15 Km 0F 15 Km 15 14 2000m 14 2000m 96 15000m 96 15000m 48 30 0 30 0 30 0 30 0 49 41 A 41 A 41 A 41 A 50 4C L 50 P 54 T 54 T 51 5A Z 5A Z 4C L 50 P 52 20 - 20 - 5A Z 5A Z 60 05 1310nm 05 1310nm 05 1310nm 05 1310nm 61 1E 1E 1E 1E 92 00 00 00 00 93 00 00 00 00 94 00 00 00 00 9 Table 4b. Individual Identifiers AFCT-5765LZ AFCT-5765PZ AFCT-5765TLZ AFCT-5765TPZ Byte # Hex Notes Hex Notes Hex Notes Hex Notes 4 10 SR-1 10 SR-1 10 IR-1 10 IR-1 5 01 OC-3 SR-1 01 OC-3 SR-1 02 OC-3 IR-1 02 OC-3 IR-1 14 02 2 Km 02 2 Km 0F 15 Km 0F 15 Km 15 14 2000m 14 2000m 96 15000m 96 15000m 48 35 5 35 5 35 5 35 5 49 4C L 50 P 54 T 54 T 50 5A Z 5A Z 4C L 50 P 51 20 - 20 - 5A Z 5A Z 20 - 05 1310nm 52 20 - 20 - 20 - 60 05 1310nm 05 1310nm 05 1310nm 61 1E 92 68 68 68 68 93 F0 F0 F0 F0 94 01 01 01 01 AFCT-5765ALZ AFCT-5765APZ AFCT-5765ATLZ AFCT-5765ATPZ 1E 1E 1E Byte # Hex Notes Hex Notes Hex Notes Hex Notes 4 10 SR-1 10 SR-1 10 IR-1 10 IR-1 5 01 OC-3 SR-1 01 OC-3 SR-1 02 OC-3 IR-1 02 OC-3 IR-1 14 02 2 KM 02 2 KM 0F 15 KM 0F 15 KM 15 14 2000m 14 2000m 96 15000m 96 15000m 48 35 5 35 5 35 5 35 5 49 41 A 41 A 41 A 41 A 50 4C L 50 P 54 T 54 T 51 5A Z 5A Z 4C L 50 P 52 20 - 20 - 5A Z 5A Z 60 05 1310nm 05 1310nm 05 1310nm 05 1310nm 61 1E 1E 1E 1E 92 68 68 68 68 93 F0 F0 F0 F0 94 01 01 01 01 10 Table 5. EEPROM Serial ID Memory Contents - Address A2h (AFCT-5765Z family only) Byte # Decimal Notes Byte # Decimal Notes Byte # Decimal Notes 0 Temp H Alarm MSB1 26 Tx Pwr L Alarm MSB4 104 Real Time Rx PAV MSB5 1 Temp H Alarm LSB1 27 Tx Pwr L Alarm LSB4 105 Real Time Rx PAV LSB5 2 Temp L Alarm MSB1 28 Tx Pwr H Warning MSB4 106 Reserved 3 Temp L Alarm LSB1 29 Tx Pwr H Warning LSB4 107 Reserved 4 Temp H Warning MSB1 30 Tx Pwr L Warning MSB4 108 Reserved 5 Temp H Warning LSB1 31 Tx Pwr L Warning LSB4 109 Reserved 6 Temp L Warning MSB1 32 Rx Pwr H Alarm MSB5 110 Status/Control - see Table 6 7 Temp L Warning LSB1 33 Rx Pwr H Alarm LSB5 111 Reserved 8 VCC H Alarm MSB2 34 Rx Pwr L Alarm MSB5 112 Flag Bits - see Table 7 9 VCC H Alarm LSB2 35 Rx Pwr L Alarm LSB5 113 Flag Bit - see Table 7 10 VCC L Alarm MSB2 36 Rx Pwr H Warning MSB5 114 Reserved 11 VCC L Alarm LSB2 37 Rx Pwr H Warning LSB5 115 Reserved 12 VCC H Warning MSB2 38 Rx Pwr L Warning MSB5 116 Flag Bits - see Table 7 13 VCC H Warning LSB2 39 Rx Pwr L Warning LSB5 117 Flag Bits - see Table 7 14 VCC L Warning MSB2 40-55 Reserved 118 Reserved 119 Reserved Reserved 15 VCC L Warning LSB2 56-94 External Calibration Constants6 16 Tx Bias H Alarm MSB3 95 Checksum for Bytes 0-947 120-122 123 17 Tx Bias H Alarm LSB3 96 Real Time Temperature MSB1 18 Tx Bias L Alarm MSB3 97 Real Time Temperature LSB1 124 19 Tx Bias L Alarm LSB3 98 Real Time Vcc MSB2 125 20 Tx Bias H Warning MSB3 99 Real Time Vcc LSB2 126 21 Tx Bias H Warning LSB3 100 Real Time Tx Bias MSB3 127 Reserved8 22 Tx Bias L Warning MSB3 101 Real Time Tx Bias LSB3 128-247 Customer Writable9 23 Tx Bias L Warning LSB3 102 Real Time Tx Power MSB4 248-254 Vendor Specific 24 Tx Pwr H Alarm MSB4 103 Real Time Tx Power LSB4 255 25 Tx Pwr H Alarm LSB4 Notes: 1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256 °C. 2. Supply voltage (VCC) is decoded as a 16 bit unsigned integer in increments of 100 μV. 3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 μA. 4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW. 5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW. 6. Bytes 55-94 are not intended from use with AFCT-5765xxxx, but have been set to default values per SFF-8472. 7. Bytes 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment. 8. Byte 127 accepts a write but performs no action (reserved legacy byte). 9. Bytes 128-247 are write enabled (customer writable). 10. Byte 255 bits 2 and 3 control laser margining (per Table 7) when an enabling password is entered into bytes 123-126. 11 Table 6. EEPROM Serial ID Memory Contents - Address A2h, Byte 110 (AFCT-5765Z family only) Bit # Status/Control Name Description 7 Tx Disable State Digital state of SFP Tx Disable Input Pin (1 = Tx_ Disable asserted) 6 Soft Tx Disable Read/write bit for changing digital state of SFP Tx_Disable function1 5 Reserved 4 Rx Rate Select State 3 Reserved 2 Tx Fault State Digital state of the SFP Tx Fault Output Pin (1 = Tx Fault asserted) 3 1 Rx LOS State Digital state of the SFP LOS Output Pin (1 = LOS asserted) 0 Data Ready (Bar) Indicates transceiver is powered and real time sense data is ready (0 = Ready) Digital state of SFP Rate Select Input Pin (1 = full bandwidth of 155 Mbit)2 Notes: 1. Bit 6 is logic OR’d with the SFP Tx_Disable input pin 3 ... either asserted will disable the SFP transmitter. 2. AFCT-5765Z does not respond to state changes on Rate Select Input Pin. It is internally hardwired to full bandwidth. 3. By default, TX_FAULT is set to trigger on hardware faults only. Table 7. EEPROM Serial ID Memory Contents - Address A2h, Bytes 112, 113, 116, 117 (AFCT-5765Z family only) Byte 112 113 116 117 12 Bit # Flag Bit Name Description 7 Temp High Alarm Set when transceiver nternal temperature exceeds high alarm threshold. 6 Temp Low Alarm Set when transceiver internal temperature exceeds alarm threshold. 5 VCC High Alarm Set when transceiver internal supply voltage exceeds high alarm threshold. 4 VCC Low Alarm Set when transceiver internal supply voltage exceeds low alarm threshold. 3 Tx Bias High Alarm Set when transceiver laser bias current exceeds high alarm threshold. 2 Tx Bias Low Alarm Set when transceiver laser bias current exceeds low alarm threshold. 1 Tx Power High Alarm Set when transmitted average optical power exceeds high alarm threshold. 0 Tx Power Low Alarm Set when transmitted average optical power exceeds low alarm threshold. 7 Rx Power High Alarm Set when received P_Avg optical power exceeds high alarm threshold. 6 Rx Power Low Alarm Set when received P_Avg optical power exceeds low alarm threshold. 0-5 Reserved 7 Temp High Warning Set when transceiver internal temperature exceeds high warning threshold. 6 Temp Low Warning Set when transceiver internal temperature exceeds low warning threshold. 5 VCC High Warning Set when transceiver internal supply voltage exceeds high warning threshold. 4 VCC Low Warning Set when transceiver internal supply voltage exceeds low warning threshold. 3 Tx Bias High Warning Set when transceiver laser bias current exceeds high warning threshold. 2 Tx Bias Low Warning Set when transceiver laser bias current exceeds low warning threshold. 1 Tx Power High Warning Set when transmitted average optical power exceeds high warning threshold. 0 Tx Power Low Warning Set when transmitted average optical power exceeds low warning threshold. 7 Rx Power High Warning Set when received P_Avg optical power exceeds high warning threshold. 9 Rx Power Low Warning Set when received P_Avg optical power exceeds low warning threshold. 0-5 Reserved Optical Parameters Absolute Maximum Ratings Absolute maximum ratings are those values beyond which functional performance is not intended, device reliability is not implied, and damage to the device may occur. Parameter Symbol Minimum Maximum Unit Storage Temperature (non-operating) TS -40 +85 °C Notes Relative Humidity RH 0 85 % Supply Voltage VCC -0.5 3.63 V Input Voltage on any Pin VI -0.5 VCC V Receiver Optical Input PINABS 0 dBm Recommended Multirate Operating Conditions Typical operating conditions are those values for which functional performance and device reliability is implied. Parameter Symbol Minimum Case Operating Temperature AFCT-576xLZ/PZ/TLZ/TPZ AFCT-576xALZ/APZ/ATLZ/ATPZ TC TC -10 -40 Supply Voltage VCC 3.1 Typical 3.3 Maximum Unit +85 +85 °C °C 3.5 V Notes Transceiver Electrical Characteristics for multirate operations at Fast Ethernet (125 Mbit/s) and OC-3 (155 Mbit/s) *6 Parameter Symbol Module supply current ICCT Power Dissipation PDISS Minimum Typical Maximum Unit Notes 250 mA 1 875 mW AC Electrical Characteristics Power Supply Noise Rejection PSNR 100 In-rush Current mV 30 mA 2 DC Electrical Characteristics Signal Outputs: Transmit Fault (TX_FAULT) Loss of Signal (LOS) Signal Inputs: Transmitter Disable (TX_DISABLE MOD-DEF1, 2 VOH 2.0 3.5 V VOL 0 0.8 V VIH 2.0 3.5 V 3 VIL 0 0.8 V 6 Data Input: Transmitter Single Ended Input Voltage (TD±) VI 250 1200 mV 4 Data Ouput: Receiver Single Ended Output Voltage (RD±) VO 160 1000 mV 5 Notes: 1. MSA gives max current at 300 mA. 2. MSA filter is required on host board 10 Hz to 2 MHz. 3. LVTTL, External 4.7-10 K pull up resistor required on host board to voltage less than Vcc + 0.3 V. 4. Internally ac coupled and terminated (100 differential). 5. Internally ac coupled and load termination located at the user SERDES. 6. Minimum input to MOD-DEF1,2 is 0.7*VCC 13 Transmitter Optical Characteristics for multirate operations at Fast Ethernet (125 Mbit/s) and OC-3 (155 Mbit/s) Parameter Maximum Unit Notes -15 -8 dBm 1 -15 -8 dBm 1 1270 1360 nm 40 nm 2 AFCT-576xTLZ/TPZ/ATLZ/ATPZ 7.7 nm 2 Optical Rise Time tr 2.5 ns 3 Optical Fall Time tf 2.5 ns 3 Tx disable OFF power POFF -45 dBm Optical Output Power Symbol Minimum POUT AFCT-576xTLZ/TPZ/ATLZ/ATPZ POUT AFCT-576xLZ/PZ/ALZ/APZ C Center Wavelength Spectral Width - RMS Extinction Ratio AFCT-576xLZ/PZ/ALZ/APZ AFCT-576xLZ/PZ/ALZ/APZ Typical* Er 8.2 dB AFCT-576xTLZ/TPZ/ATLZ/ATPZ Er 8.2 dB 30 % 4 Eye Mask Margin EMM Jitter Generation pk to pk 70 mUI 5 RMS 7 mUI 5 *Typicals indicated expected values for room temperature measurements +25 °C Notes: 1. The output power is coupled into a 1 m single mode fiber. Minimum output optical level is at end of life 2. The relationship between FWHM and RMS values for spectral width can derived from the Gaussian shaped spectrum which results in RMS=FWHM/2.35 3. These are unfiltered 20-80% values. 4. 30% margin to eye mask in Telcordia GR-253-CORE and ITU-T G.957 5. Jitter measurements taken with Avago OMNIBER 718 in accordance with GR253 Receiver Optical Characteristics for multirate operations at Fast Ethernet (125 Mbit/s) and OC-3 (155 Mbit/s) Notes: Parameter Receiver Sensitivity Maximum Unit AFCT-576xLZ/PZ/ALZ/APZ PINMIN Symbol Minimum -23 dBm 1 AFCT-576xTLZ/TPZ/ATLZ/ATPZ PINMIN -31 dBm 1 Receiver Overload PINMAX -8 Input Operating Wavelength 1261 LOS Deassert Typical dBm 1360 nm AFCT-576xLZ/PZ/ALZ/APZ PLOSD -23.5 dBm AFCT-576xTLZ/TPZ/ATLZ/ATPZ PLOSD -31.5 dBm LOS Assert PLOSA -45 LOS Hysteresis PH 0.5 Notes dBm 4 dB 1. The receiver is guaranteed to provide output data with a Bit Error Rate better than or equal to 1 x 10-10 measured with TX powered and carrying data. 14 Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics (AFCT-5765Z family only) Parameter Symbol Min. Max. Unit Reference Transceiver Internal Temperature Accuracy TINT -3.0 Typ. +3.0 °C 1 Transceiver Internal Supply Voltage Accuracy VINT -3.0 +3.0 % 2 Transmitter Laser dc Bias Current Accuracy IINT -10 +10 % 3 Transmitted Average Optical Output Power Accuracy PT -3.0 +3.0 dB Received Average Optical Input Power Accuracy PR -3.0 +3.0 dB Notes: 1. Temperature was measured internal to the transceiver. Valid from = -10 °C to +85 °C or from -40°C to +85°C. For calibration to an external temperature, please contact Avago Technologies. 2. Reference voltage is 3.3 V. 3. Valid from 0 to 50 mA, avg. Transceiver Timing Characteristics Parameter Symbol Hardware TX_DISABLE Assert Time Minimum Maximum Unit Notes t_off 10 ms Note 1 Hardware TX_DISABLE Negate Time t_on 1 ms Note 2 Time to initialize, including reset of TX_FAULT t_init 300 ms Note 3 Hardware TX_FAULT Assert Time t_fault 100 ms Note 4 Hardware TX_DISABLE to Reset t_reset ms Note 5 Hardware RX_LOS Assert Time t_loss_on 100 ms Note 6 Hardware RX_LOS De-Assert Time t_loss_off 100 ms Note 7 Software TX_DISABLE Assert Time t_off_soft 100 ms Note 8 Software TX_DISABLE Negate Time t_on_soft 100 ms Note 9 Software Tx_FAULT Assert Time t_fault_soft 100 ms Note 10 Software Rx_LOS Assert Time t_loss_on_soft 100 ms Note 11 Software Rx_LOS De-Assert Time t_loss_off_soft 100 ms Note 12 Analog parameter data ready t_data 1000 ms Note 13 Serial bus hardware ready t_serial 300 ms Note 14 Write Cycle Time t_write 10 ms Note 15 Serial ID Clock Rate f_serial_clock 400 kHz 10 Notes: 1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal. 2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal. 3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal. 4. From power on or negation of TX_FAULT using TX_DISABLE. 5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry. 6. Time from loss of optical signal to Rx_LOS Assertion. 7. Time from valid optical signal to Rx_LOS De-Assertion. 8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured from falling clock edge after stop bit of write transaction. 9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of nominal. 10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted. 11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal. 12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal. 13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional. 14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h). 15. Time from stop bit to completion of a 1-8 byte write command. 15 VCC > 3.15 V VCC > 3.15 V Tx_FAULT Tx_FAULT Tx_DISABLE Tx_DISABLE TRANSMITTED SIGNAL TRANSMITTED SIGNAL t_init t_init t-init: TX DISABLE NEGATED t-init: TX DISABLE ASSERTED VCC > 3.15 V Tx_FAULT Tx_FAULT Tx_DISABLE Tx_DISABLE TRANSMITTED SIGNAL TRANSMITTED SIGNAL t_off t_on t_init INSERTION t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED t-off & t-on: TX DISABLE ASSERTED THEN NEGATED OCCURANCE OF FAULT OCCURANCE OF FAULT Tx_FAULT Tx_FAULT Tx_DISABLE Tx_DISABLE TRANSMITTED SIGNAL TRANSMITTED SIGNAL t_reset t_fault * CANNOT READ INPUT... t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED t_init* t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED OCCURANCE OF FAULT Tx_FAULT LOS TRANSMITTED SIGNAL t_fault t_loss_on t_reset * SFP SHALL CLEAR Tx_FAULT IN t_init IF THE FAILURE IS TRANSIENT t-fault: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL NOT RECOVERED Figure 5. Timing Diagrams 16 OCCURANCE OF LOSS OPTICAL SIGNAL Tx_DISABLE t_init* t-loss-on & t-loss-off t_loss_off AVAGO AFCT-576xZ ### nm LASER PROD 21CFR(J) CLASS 1 COUNTRY OF ORIGIN YYWW ###### Notes: 1. Bail delatch is colored BLUE for SONET/Single-Mode Identification. Figure 6. Module Drawing 17 Figure 7. Assembly Drawing 18 Figure 8. SFP host board mechnical layout 19 Ordering Information Please contact your local field sales engineer or one of Avago Technologies franchised distributors for ordering information. For technical information, please visit Avago Technologies’ web-page at www.avagotech.com or contact one of Avago Technologies’ regional Technical Response Centers. For information related to SFF Committee documentation, visit www.sffcommittee.org. 1300nm FP Laser (Operating Case Temperature -10 to +85 °C) With DMI AFCT-5765LZ SR standard de-latch (2 km) AFCT-5765PZ SR bail de-latch (2 km) AFCT-5765TLZ IR standard de-latch (15 km) AFCT-5765TPZ IR bail de-latch (15 km) Without DMI AFCT-5760LZ SR standard de-latch (2 km) AFCT-5760PZ SR bail de-latch (2 km) AFCT-5760TLZ IR standard de-latch (15 km) AFCT-5760TPZ IR bail de-latch (15 km) 1300nm FP Laser (Operating Case Temperature -40 to +85 °C) With DMI AFCT-5765ALZ SR standard de-latch (2 km) AFCT-5765APZ SR bail de-latch (2 km) AFCT-5765ATLZ IR standard de-latch (15 km) AFCT-5765ATPZ IR bail de-latch (15 km) Without DMI AFCT-5760ALZ SR standard de-latch (2 km) AFCT-5760APZ SR bail de-latch (2 km) AFCT-5760ATLZ IR standard de-latch (15 km) AFCT-5760ATPZ IR bail de-latch (15 km) EEPROM Content and / or Label Options AFCT-5760XXXX-YYY AFCT-5765XXXX-YYY Where “XXXX” refers to product option “YYY” is customer specific For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes AV01-0510EN AV02-0136EN - September 12, 2012