Ironwood CA-MLF32A-A-Z-T-01 Carrier adaptor 32 position mlf zif socket to 32 position surface mountable mlf emulator foot with test probes. Datasheet

30.48mm [1.200"]
31
25
32
26
1
2
24
23
7
8
18
17
30.48mm
[1.200"]
2.54mm
[0.100"]
Top View
10
16
9
15
10.36mm
[0.408"]
Side View
SK-UGA6/33A-03
SF-MLF32A-A-02
Description: Carrier Adaptor
32 position MLF ZIF socket to 32 position surface mountable MLF emulator foot with test probes.
Pin assignment/ interconnect 1:1.
Tolerances: diameters ±0.03mm [±0.001”], PCB perimeters ±0.13mm [±0.005”], PCB thicknesses ±0.18mm [±0.007"], pitches (from true position)
±0.08mm [±0.003"], all other tolerances ±0.13mm [±0.005”] unless stated otherwise. Materials and specifications are subject to change without notice.
CA-MLF32A-A-Z-T-01 Drawing
© 2004 IRONWOOD ELECTRONICS, INC.
PO BOX 21151 ST. PAUL, MN 55121
Tele: (651) 452-8100
www.ironwoodelectronics.com
Status: Released
Scale: 3:1
Rev: B
Drawing: H. Hansen
Date: 4/5/04
File: CA-MLF32A-A-Z-T-01 Dwg
Modified: 9/26/05
Recommended torque = 1.5 in. lbs.
(24 in. oz.)
3
22.31mm
[0.878"]
1
board UGA
SK-UGA6/33A-03
SF-MLF32A-A-02
2
1
2
Apply torque and then
plug into SF-MLF foot.
1
Substrate: 2.34mm ±0.18mm [0.092" ±0.007"]
FR4/G10 or equivalent high temp material. 17µm
[1/2 oz.] Cu clad. SnPb plating.
2
Pins: material- Brass Alloy 360 1/2 hard; finish0.25µm [10µ"] Au over 1.27µm [50µ"] Ni (min.).
3
Test points: material- Phosphor Bronze; platingSn over 1.27µm [50µ"] Ni. Gold flash on contact
end.
NOTE: Do not apply
torque when assemby is
pluged into SF-MLF foot.
User Instructions:
1. Attach SF-MLF32A-A-02 foot to the target board.
2. Turn plastic thumb screws until head touches bottom of CA-MLF32A-A-Z-T-01 board.
3. Insert SK-UGA6/33A-03 into board UGA. Check orientation.
4. Remove socket lid and compression plate.
5. Insert MLF package into IC guide inside socket cavity.
6.Put compression plate and socket lid in place.
7. Hold socket assembly and apply recommended torque.
8. Carefully insert CA-MLF assembly into SF-MLF feet UGA. Check orientation.
9. Unscrew plastic thumb screws until they hit target board.
CA-MLF32A-A-Z-T-01 Drawing
© 2004 IRONWOOD ELECTRONICS, INC.
PO BOX 21151 ST. PAUL, MN 55121
Tele: (651) 452-8100
www.ironwoodelectronics.com
Status: Released
Scale: 3:1
Rev: B
Drawing: H. Hansen
Date: 4/5/04
File: CA-MLF32A-A-Z-T-01 Dwg
Modified: 6/26/05
Similar pages