FRA1001G THRU FRA1007G 10 AMPS. Glass Passivated Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 10 Amperes TO-220A Features .185(4.70) .175(4.44) Low forward voltage drop High current capability High reliability High surge current capability .412(10.5) MAX .113(2.87) .103(2.62) .27(6.86) .23(5.84) .594(15.1) .587(14.9) Mechanical Data .055(1.40) .045(1.14) DIA .154(3.91) .148(3.74) PIN1 2 .16(4.06) .14(3.56) Cases: ITO-220AC molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Leads solderable per MIL-STD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260℃/10 seconds .16”,(4.06mm) from case. Mounting position: Any Weight: 2.24 grams .56(14.22) .53(13.46) .11(2.79) .10(2.54) .037(0.94) .027(0.68) .025(0.64) .014(0.35) .205(5.20) .195(4.95) PIN 1 PIN 2 CASE Case Positive Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FRA FRA FRA Type Number FRA FRA FRA FRA 1001G 1002G 1003G 1004G 1005G 1006G 1007G Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 Units V V V I(AV) 10 A IFSM 150 A Maximum Instantaneous Forward Voltage @ 10A VF Maximum DC Reverse Current @ TC=25℃ at Rated DC Blocking Voltage @ TC=125℃ IR 1.3 5.0 100 Maximum Reverse Recovery Time ( Note 2 ) Trr Typical Junction Capacitance ( Note 1 ) TJ=25℃ Cj V uA uA nS pF ℃/W ℃ Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range 150 RθJC TJ ,TSTG 250 100 3.0 -65 to +150 Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4..0 Volts D.C. 2. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 3. Thermal Resistance from Junction to Case, with Heatsink size 2” x 3” x 0.25” Al-Plate - 456 - 500 RATINGS AND CHARACTERISTIC CURVES (FRA1001G THRU FRA1007G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 400 10 200 6 4 2 0 0 50 100 150 o PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) 150 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 40 Tj=25oC Pulse Width=300 s 1% Duty Cycle 20 10 4 2 1 0.4 0.2 125 0.1 0.6 0 TJ=125 C 100 8.3ms Single Half Sine Wave JEDEC Method 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE. (V) 75 FIG.6- TYPICAL REVERSE CHARACTERISTICS 50 100 25 0 1 40 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 300 CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 8 250 200 150 100 50 0 0.1 Tj=25 0C f=1.0MHz Vsig=50mVp-p INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE SET TIME BASE FOR 5/ 10ns/ cm Tj=125 0C 10 2 1 0.4 1 5 10 50 100 500 1000 Tj=25 0C 0.2 0.1 0.5 Tj=75 0C 4 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) REVERSE VOLTAGE. (V) - 457 -