ON MC74HC4053 High-performance silicon-gate cmo Datasheet

http://onsemi.com
This document,
MC74HC4051/D
has been canceled and
replaced by
MC74HC4051A/D
LAN was sent 9/28/01
MC54/74HC4051 MC74HC4052 MC54/74HC4053
Analog Multiplexers/
Demultiplexers
MC54/74HC4051
MC74HC4052
MC54/74HC4053
High–Performance Silicon–Gate CMOS
The MC54/74HC4051, MC74HC4052 and MC54/74HC4053 utilize silicon–gate CMOS technology to achieve fast propagation delays, low ON
resistances, and low OFF leakage currents. These analog multiplexers/
demultiplexers control analog voltages that may vary across the complete
power supply range (from VCC to VEE).
The HC4051, HC4052 and HC4053 are identical in pinout to the
metal–gate MC14051B, MC14052B and MC14053B. The Channel–Select
inputs determine which one of the Analog Inputs/Outputs is to be connected,
by means of an analog switch, to the Common Output/Input. When the
Enable pin is HIGH, all analog switches are turned off.
The Channel–Select and Enable inputs are compatible with standard
CMOS outputs; with pullup resistors they are compatible with LSTTL
outputs.
These devices have been designed so that the ON resistance (Ron) is
more linear over input voltage than R on of metal–gate CMOS analog
switches.
For multiplexers/demultiplexers with channel–select latches, see
HC4351, HC4352 and HC4353.
• Fast Switching and Propagation Speeds
• Low Crosstalk Between Switches
• Diode Protection on All Inputs/Outputs
• Analog Power Supply Range (VCC – VEE) = 2.0 to 12.0 V
• Digital (Control) Power Supply Range (VCC – GND) = 2.0 to 6.0 V
• Improved Linearity and Lower ON Resistance Than Metal–Gate
Counterparts
• Low Noise
• In Compliance With the Requirements of JEDEC Standard No. 7A
• Chip Complexity: HC4051 — 184 FETs or 46 Equivalent Gates
HC4052 — 168 FETs or 42 Equivalent Gates
HC4053 — 156 FETs or 39 Equivalent Gates
16
1
1
1
1
DW SUFFIX
SOIC PACKAGE
CASE 751G–02
1
DT SUFFIX
TSSOP PACKAGE
CASE 948F–01
16
16
ORDERING INFORMATION
MC54HCXXXXJ
MC74HCXXXXN
MC74HCXXXXD
MC74HCXXXXDW
MC74HCXXXXDT
Ceramic
Plastic
SOIC
SOIC Wide
TSSOP
FUNCTION TABLE – MC54/74HC4051
Control Inputs
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
COMMON
OUTPUT/
INPUT
X
D SUFFIX
SOIC PACKAGE
CASE 751B–05
16
13
3
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
16
LOGIC DIAGRAM
MC54/74HC4051
Single–Pole, 8–Position Plus Common Off
X0
14
X1
15
X2
ANALOG
12
MULTIPLEXER/
INPUTS/ X3
DEMULTIPLEXER
OUTPUTS X4 1
5
X5
2
X6
4
X7
11
A
CHANNEL
10
B
SELECT
9
INPUTS
C
6
ENABLE
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
J SUFFIX
CERAMIC PACKAGE
CASE 620–10
VCC
X2
X1
X0
X3
A
B
C
16
15
14
13
12
11
10
9
6
7
1
2
3
4
5
X6
X
X7
X5
Enable VEE
L
L
H
H
L
L
H
H
X
L
H
L
H
L
H
L
H
X
ON Channels
X0
X1
X2
X3
X4
X5
X6
X7
NONE
X = Don’t Care
Pinout: MC54/74HC4051 (Top View)
X4
Select
B
A
8
GND
MC54/74HC4051 MC74HC4052 MC54/74HC4053
FUNCTION TABLE – MC74HC4052
LOGIC DIAGRAM
MC74HC4052
Double–Pole, 4–Position Plus Common Off
12
ANALOG
INPUTS/OUTPUTS
CHANNELSELECT
INPUTS
X0
14
X1
15
X2
11
X3
Y0
Y1
Y2
Y3
A
B
ENABLE
X SWITCH
13
COMMON
OUTPUTS/INPUTS
2
Y SWITCH
3
Select
Enable
B
A
ON Channels
L
L
L
L
H
L
L
H
H
X
L
H
L
H
X
Y0
Y1
Y2
Y3
X
1
5
Control Inputs
X0
X1
X2
X3
NONE
X = Don’t Care
Y
4
Pinout: MC74HC4052 (Top View)
10
9
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
6
VCC
X2
X1
X
X0
X3
A
B
16
15
14
13
12
11
10
9
6
7
1
2
3
4
5
Y0
Y2
Y
Y3
Y1
Enable VEE
8
GND
FUNCTION TABLE – MC54/74HC4053
LOGIC DIAGRAM
MC54/74HC4053
Triple Single–Pole, Double–Position Plus Common Off
12
X0
13
X1
X SWITCH
2
ANALOG
INPUTS/OUTPUTS
Y0
1
Y1
Y SWITCH
5
Z0
3
Z1
Z SWITCH
14
15
4
Control Inputs
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
X
Y
COMMON
OUTPUTS/INPUTS
Z
Select
B
A
L
L
H
H
L
L
H
H
X
ON Channels
L
H
L
H
L
H
L
H
X
Z0
Z0
Z0
Z0
Z1
Z1
Z1
Z1
Y0
Y0
Y1
Y1
Y0
Y0
Y1
Y1
NONE
X0
X1
X0
X1
X0
X1
X0
X1
X = Don’t Care
11
A
10
B
9
C
6
ENABLE
CHANNELSELECT
INPUTS
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
Pinout: MC54/74HC4053 (Top View)
VCC
Y
X
X1
X0
A
B
C
16
15
14
13
12
11
10
9
6
7
NOTE: This device allows independent control of each switch.
Channel–Select Input A controls the X–Switch, Input B controls
the Y–Switch and Input C controls the Z–Switch
1
2
3
4
5
Y1
Y0
Z1
Z
Z0
Enable VEE
8
GND
MC54/74HC4051 MC74HC4052 MC54/74HC4053
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
MAXIMUM RATINGS*
Symbol
Parameter
(Referenced to GND)
(Referenced to VEE)
Value
Unit
– 0.5 to + 7.0
– 0.5 to + 14.0
V
VCC
Positive DC Supply Voltage
VEE
Negative DC Supply Voltage (Referenced to GND)
– 7.0 to + 5.0
V
VIS
Analog Input Voltage
VEE – 0.5 to
VCC + 0.5
V
Vin
Digital Input Voltage (Referenced to GND)
– 0.5 to VCC + 0.5
V
DC Current, Into or Out of Any Pin
± 25
mA
PD
Power Dissipation in Still Air, Plastic or Ceramic DIP†
SOIC Package†
TSSOP Package†
750
500
450
mW
Tstg
Storage Temperature Range
– 65 to + 150
C
TL
Lead Temperature, 1 mm from Case for 10 Seconds
Plastic DIP, SOIC or TSSOP Package
Ceramic DIP
I
C
260
300
* Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
†Derating — Plastic DIP: – 10 mW/C from 65 to 125C
Ceramic DIP: – 10 mW/C from 100 to 125C
SOIC Package: – 7 mW/C from 65 to 125C
TSSOP Package: – 6.1 mW/C from 65 to 125C
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
(Referenced to GND)
(Referenced to VEE)
Min
Max
Unit
2.0
2.0
6.0
12.0
V
VCC
Positive DC Supply Voltage
VEE
Negative DC Supply Voltage, Output (Referenced to
GND)
– 6.0
GND
V
VIS
Analog Input Voltage
VEE
VCC
V
Vin
Digital Input Voltage (Referenced to GND)
GND
VCC
V
VIO*
Static or Dynamic Voltage Across Switch
1.2
V
– 55
+ 125
C
0
0
0
1000
500
400
ns
TA
Operating Temperature Range, All Package Types
tr, tf
Input Rise/Fall Time
(Channel Select or Enable Inputs)
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
* For voltage drops across switch greater than 1.2V (switch on), excessive VCC current may be
drawn; i.e., the current out of the switch may contain both VCC and switch input components. The
reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high–impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND (Vin or Vout) VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
MC54/74HC4051 MC74HC4052 MC54/74HC4053
DC CHARACTERISTICS — Digital Section (Voltages Referenced to GND) VEE = GND, Except Where Noted
Condition
Guaranteed Limit
VCC
V
–55 to 25°C
≤85°C
≤125°C
Unit
Symbol
Parameter
VIH
Minimum High–Level Input Voltage,
Channel–Select or Enable Inputs
Ron = Per Spec
2.0
4.5
6.0
1.50
3.15
4.20
1.50
3.15
4.20
1.50
3.15
4.20
V
VIL
Maximum Low–Level Input Voltage,
Channel–Select or Enable Inputs
Ron = Per Spec
2.0
4.5
6.0
0.3
0.9
1.2
0.3
0.9
1.2
0.3
0.9
1.2
V
Iin
Maximum Input Leakage Current,
Channel–Select or Enable Inputs
Vin = VCC or GND,
VEE = – 6.0 V
6.0
± 0.1
± 1.0
± 1.0
µA
ICC
Maximum Quiescent Supply
Current (per Package)
Channel Select, Enable and
VIS = VCC or GND;
VEE = GND
VEE = – 6.0
VIO = 0 V
6.0
6.0
2
8
20
80
40
160
µA
DC CHARACTERISTICS — Analog Section
Guaranteed Limit
Symbol
Ron
Parameter
Maximum “ON” Resistance
VCC
VEE
–55 to 25°C
≤85°C
≤125°C
Unit
Vin = VIL or VIH; VIS = VCC to
VEE; IS ≤ 2.0 mA
(Figures 1, 2)
4.5
4.5
6.0
0.0
– 4.5
– 6.0
190
120
100
240
150
125
280
170
140
Ω
Vin = VIL or VIH; VIS = VCC or
VEE (Endpoints); IS ≤ 2.0 mA
(Figures 1, 2)
4.5
4.5
6.0
0.0
– 4.5
– 6.0
150
100
80
190
125
100
230
140
115
Condition
∆Ron
Maximum Difference in “ON”
Resistance Between Any Two
Channels in the Same Package
Vin = VIL or VIH;
VIS = 1/2 (VCC – VEE);
IS ≤ 2.0 mA
4.5
4.5
6.0
0.0
– 4.5
– 6.0
30
12
10
35
15
12
40
18
14
Ioff
Maximum Off–Channel Leakage
Current, Any One Channel
Vin = VIL or VIH;
VIO = VCC – VEE;
Switch Off (Figure 3)
6.0
– 6.0
0.1
0.5
1.0
Maximum Off–Channel HC4051
Leakage Current,
HC4052
Common Channel
HC4053
Vin = VIL or VIH;
VIO = VCC – VEE;
Switch Off (Figure 4)
6.0
6.0
6.0
– 6.0
– 6.0
– 6.0
0.2
0.1
0.1
2.0
1.0
1.0
4.0
2.0
2.0
Maximum On–Channel HC4051
Leakage Current,
HC4052
Channel–to–Channel
HC4053
Vin = VIL or VIH;
Switch–to–Switch =
VCC – VEE; (Figure 5)
6.0
6.0
6.0
– 6.0
– 6.0
– 6.0
0.2
0.1
0.1
2.0
1.0
1.0
4.0
2.0
2.0
Ion
Ω
µA
µA
MC54/74HC4051 MC74HC4052 MC54/74HC4053
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Symbol
Parameter
Guaranteed Limit
VCC
V
–55 to 25°C
≤85°C
≤125°C
Unit
tPLH,
tPHL
Maximum Propagation Delay, Channel–Select to Analog Output
(Figure 9)
2.0
4.5
6.0
370
74
63
465
93
79
550
110
94
ns
tPLH,
tPHL
Maximum Propagation Delay, Analog Input to Analog Output
(Figure 10)
2.0
4.5
6.0
60
12
10
75
15
13
90
18
15
ns
tPLZ,
tPHZ
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
4.5
6.0
290
58
49
364
73
62
430
86
73
ns
tPZL,
tPZH
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
4.5
6.0
345
69
59
435
87
74
515
103
87
ns
Cin
Maximum Input Capacitance, Channel–Select or Enable Inputs
10
10
10
pF
CI/O
Maximum Capacitance
Analog I/O
35
35
35
pF
Common O/I: HC4051
HC4052
HC4053
130
80
50
130
80
50
130
80
50
Feedthrough
1.0
1.0
1.0
(All Switches Off)
Typical @ 25°C, VCC = 5.0 V, VEE = 0 V
CPD
Power Dissipation Capacitance (Figure 13)*
HC4051
HC4052
HC4053
45
80
45
pF
MC54/74HC4051 MC74HC4052 MC54/74HC4053
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
Symbol
BW
—
—
—
THD
Parameter
Condition
Maximum On–Channel Bandwidth
or Minimum
Mi i
Frequency
F
Response
R
(Figure 6)
fin = 1MHz Sine Wave; Adjust fin Voltage to
Obt i 0dB
Obtain
0dBm att VOS; IIncrease fin F
Frequency
Until dB Meter Reads –3dB;
RL = 50Ω, CL = 10pF
Off–Channel Feedthrough Isolation
(Figure 7)
Feedthrough Noise.
Channel–Select Input to Common
I/O (Figure 8)
Crosstalk Between Any Two
Switches (Figure 12)
(Test does not apply to HC4051)
Total Harmonic Distortion
(Figure 14)
VCC
V
Limit*
VEE
V
25°C
‘51
‘52
‘53
80
80
80
95
95
95
120
120
120
2.25
4.50
6.00
–2.25
–4.50
–6.00
fin = Sine Wave; Adjust fin Voltage to Obtain
0dBm at VIS
fin = 10kHz, RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–50
–50
–50
fin = 1.0MHz, RL = 50Ω, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–40
–40
–40
Vin ≤ 1MHz Square Wave (tr = tf = 6ns);
Adjust RL at Setup so that IS = 0A;
Enable = GND
RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
25
105
135
RL = 10kΩ, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
35
145
190
fin = Sine Wave; Adjust fin Voltage to Obtain
0dBm at VIS
fin = 10kHz, RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–50
–50
–50
fin = 1.0MHz, RL = 50Ω, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–60
–60
–60
fin = 1kHz, RL = 10kΩ, CL = 50pF
THD = THDmeasured – THDsource
VIS = 4.0VPP sine wave
VIS = 8.0VPP sine wave
VIS = 11.0VPP sine wave
* Limits not tested. Determined by design and verified by qualification.
Unit
MHz
dB
mVPP
dB
%
2.25
4.50
6.00
–2.25
–4.50
–6.00
0.10
0.08
0.05
300
120
250
100
200
Ron , ON RESISTANCE (OHMS)
Ron , ON RESISTANCE (OHMS)
MC54/74HC4051 MC74HC4052 MC54/74HC4053
125°C
150
25°C
100
-55°C
50
0
0
0.25
0.50
0.75
1.0
1.25
1.5
1.75
2.0
80
25°C
60
-55°C
40
20
0
2.25
125°C
0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
1.5
2.5
3.0
3.5
4.0
90
125°C
75
25°C
Ron , ON RESISTANCE (OHMS)
105
60
45
-55°C
30
0
0.5
1.0
1.5 2.0
2.5
3.0
3.5
4.0 4.5
5.0
5.5
6.0
75
Figure 1c. Typical On Resistance, VCC – VEE = 6.0 V
125°C
60
25°C
45
-55°C
30
15
0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
Figure 1d. Typical On Resistance, VCC – VEE = 9.0 V
PLOTTER
70
60
125°C
50
25°C
40
PROGRAMMABLE
POWER
SUPPLY
-
MINI COMPUTER
VCC
DEVICE
UNDER TEST
20
ANALOG IN
10
0
1.0 2.0
3.0
4.0
5.0 6.0
7.0
8.0 9.0 10.0 11.0 12.0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1e. Typical On Resistance, VCC – VEE = 12.0 V
DC ANALYZER
+
-55°C
30
9.0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
80
0
4.5
90
15
Ron , ON RESISTANCE (OHMS)
2.0
Figure 1b. Typical On Resistance, VCC – VEE = 4.5 V
120
Ron , ON RESISTANCE (OHMS)
1.0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1a. Typical On Resistance, VCC – VEE = 2.0 V
0
0.5
GND
COMMON OUT
VEE
Figure 2. On Resistance Test Set–Up
MC54/74HC4051 MC74HC4052 MC54/74HC4053
VCC
VCC
VCC
16
VEE
OFF
A
VCC
VEE
VIH
OFF
VIH
6
7
8
VEE
6
7
8
VCC
COMMON O/I
OFF
fin
N/C
VOS
16
0.1µF
ON
VEE
Figure 4. Maximum Off Channel Leakage Current,
Common Channel, Test Set–Up
VCC
16
A
VCC
COMMON O/I
VEE
Figure 3. Maximum Off Channel Leakage Current,
Any One Channel, Test Set–Up
VCC
OFF
VCC
COMMON O/I
OFF
NC
VCC
16
ANALOG I/O
dB
METER
ON
RL
CL*
ANALOG I/O
VIL
6
7
8
6
7
8
VEE
VEE
Figure 5. Maximum On Channel Leakage Current,
Channel to Channel, Test Set–Up
VCC
VIS
0.1µF
VCC
dB
METER
OFF
RL
Figure 6. Maximum On Channel Bandwidth,
Test Set–Up
VOS
16
fin
*Includes all probe and jig capacitance
CL*
16
RL
OFF/ON
RL
6
7
8
VEE
VIL or VIH
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 7. Off Channel Feedthrough Isolation,
Test Set–Up
VCC
GND
Vin ≤ 1 MHz
tr = tf = 6 ns
6
7
8
VEE
COMMON O/I
ON/OFF
ANALOG I/O
RL
RL
CL*
TEST
POINT
VCC
11
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 8. Feedthrough Noise, Channel Select to
Common Out, Test Set–Up
MC54/74HC4051 MC74HC4052 MC54/74HC4053
VCC
VCC
16
VCC
CHANNEL
SELECT
50%
OFF/ON
GND
tPLH
COMMON O/I
ON/OFF
ANALOG I/O
CL*
TEST
POINT
tPHL
ANALOG
OUT
6
7
8
50%
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 9a. Propagation Delays, Channel Select
to Analog Out
Figure 9b. Propagation Delay, Test Set–Up Channel
Select to Analog Out
VCC
16
ANALOG I/O
VCC
ANALOG
IN
COMMON O/I
ON
50%
CL*
tPLH
tPHL
ANALOG
OUT
TEST
POINT
GND
6
7
8
50%
*Includes all probe and jig capacitance
Figure 10a. Propagation Delays, Analog In
to Analog Out
tf
tr
90%
50%
10%
ENABLE
tPZL
ANALOG
OUT
tPLZ
50%
tPZH
ANALOG
OUT
Figure 10b. Propagation Delay, Test Set–Up
Analog In to Analog Out
tPHZ
90%
GND
VCC
VCC
16
1
ANALOG I/O
VOH
HIGH
IMPEDANCE
1kΩ
ON/OFF
2
CL*
VOL
50%
Figure 11a. Propagation Delays, Enable to
Analog Out
POSITION 1 WHEN TESTING tPHZ AND tPZH
POSITION 2 WHEN TESTING tPLZ AND tPZL
2
HIGH
IMPEDANCE
10%
1
VCC
ENABLE
6
7
8
Figure 11b. Propagation Delay, Test Set–Up
Enable to Analog Out
TEST
POINT
MC54/74HC4051 MC74HC4052 MC54/74HC4053
VCC
VIS
16
RL
fin
A
VCC
16
VOS
ON
COMMON O/I
ON/OFF
ANALOG I/O
0.1µF
OFF/ON
NC
OFF
VEE
RL
RL
CL*
RL
CL*
6
7
8
VEE
VCC
6
7
8
11
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 12. Crosstalk Between Any Two
Switches, Test Set–Up
Figure 13. Power Dissipation Capacitance,
Test Set–Up
0
VIS
VCC
0.1µF
fin
ON
CL*
-20
TO
DISTORTION
METER
-30
-40
dB
RL
-50
DEVICE
-60
6
7
8
VEE
FUNDAMENTAL FREQUENCY
-10
VOS
16
SOURCE
-70
-80
*Includes all probe and jig capacitance
-90
-100
1.0
2.0
3.125
FREQUENCY (kHz)
Figure 14a. Total Harmonic Distortion, Test Set–Up
Figure 14b. Plot, Harmonic Distortion
APPLICATIONS INFORMATION
The Channel Select and Enable control pins should be at
VCC or GND logic levels. VCC being recognized as a logic
high and GND being recognized as a logic low. In this example:
VCC = +5V = logic high
GND = 0V = logic low
The maximum analog voltage swings are determined by
the supply voltages VCC and VEE. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below VEE. In this example, the
difference between VCC and VEE is ten volts. Therefore,
using the configuration of Figure 15, a maximum analog signal of ten volts peak–to–peak can be controlled. Unused
analog inputs/outputs may be left floating (i.e., not connected). However, tying unused analog inputs and outputs to
VCC or GND through a low value resistor helps minimize
crosstalk and feedthrough noise that may be picked up by an
unused switch.
Although used here, balanced supplies are not a requirement. The only constraints on the power supplies are that:
VCC – GND = 2 to 6 volts
VEE – GND = 0 to –6 volts
VCC – VEE = 2 to 12 volts
and VEE ≤ GND
When voltage transients above VCC and/or below VEE are
anticipated on the analog channels, external Germanium or
Schottky diodes (Dx) are recommended as shown in Figure
16. These diodes should be able to absorb the maximum
anticipated current surges during clipping.
MC54/74HC4051 MC74HC4052 MC54/74HC4053
VCC
+5V
+5V
16
ANALOG
SIGNAL
-5V
ON
6
7
8
Dx
+5V
ANALOG
SIGNAL
VCC
16
Dx
Dx
VEE
VEE
7
8
-5V
VEE
Figure 15. Application Example
Figure 16. External Germanium or
Schottky Clipping Diodes
+5V
+5V
16
ANALOG
SIGNAL
VEE
ON/OFF
6
7
8
VEE
Dx
ON/OFF
-5V
TO EXTERNAL CMOS
CIRCUITRY 0 to 5V
DIGITAL SIGNALS
11
10
9
VCC
+5V
ANALOG
SIGNAL
+5V
*
R
R
11
10
9
+5V
VEE
+5V
VEE
16
ANALOG
SIGNAL
ON/OFF
R
VEE
+5V
6
7
8
LSTTL/NMOS
CIRCUITRY
VEE
* 2K ≤ R ≤ 10K
+5V
ANALOG
SIGNAL
a. Using Pull–Up Resistors
11
10
9
LSTTL/NMOS
CIRCUITRY
HCT
BUFFER
b. Using HCT Interface
Figure 17. Interfacing LSTTL/NMOS to CMOS Inputs
A
11
13
LEVEL
SHIFTER
14
B
10
15
LEVEL
SHIFTER
12
C
9
1
LEVEL
SHIFTER
5
ENABLE
6
2
LEVEL
SHIFTER
4
3
Figure 18. Function Diagram, HC4051
X0
X1
X2
X3
X4
X5
X6
X7
X
MC54/74HC4051 MC74HC4052 MC54/74HC4053
A
10
12
LEVEL
SHIFTER
14
B
9
15
LEVEL
SHIFTER
11
13
ENABLE
6
1
LEVEL
SHIFTER
5
2
4
3
X0
X1
X2
X3
X
Y0
Y1
Y2
Y3
Y
Figure 19. Function Diagram, HC4052
A
11
13
LEVEL
SHIFTER
12
14
B
10
1
LEVEL
SHIFTER
2
15
C
9
3
LEVEL
SHIFTER
5
4
ENABLE
6
LEVEL
SHIFTER
Figure 20. Function Diagram, HC4053
X1
X0
X
Y1
Y0
Y
Z1
Z0
Z
MC54/74HC4051 MC74HC4052 MC54/74HC4053
OUTLINE DIMENSIONS
J SUFFIX
CERAMIC PACKAGE
CASE 620–10
ISSUE V
–A
–
16
9
1
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIM F MAY NARROW TO 0.76 (0.030) WHERE
THE LEAD ENTERS THE CERAMIC BODY.
–B
–
L
C
DIM
A
B
C
D
E
F
G
J
K
L
M
N
–T
SEATING
–
PLANE
K
N
E
M
F
J 16 PL
0.25 (0.010)
G
D 16 PL
0.25 (0.010)
T A
M
9
1
8
T B
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
ISSUE R
–A
–
16
M
C
DIM
A
B
C
D
F
G
H
J
K
L
M
S
L
S
–T
–
SEATING
PLANE
K
H
D 16 PL
0.25 (0.010)
M
M
J
G
T A
M
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
ISSUE J
–A
–
16
–B
–
P 8 PL
0.25 (0.010)
8
M
B
M
G
K
F
R X 45°
C
–T
SEATING
–
PLANE
D16PL
0.25 (0.010)
M
M
T
B
S
A
S
INCHES
MILLIMETERS
MIN
MAX
MIN
MAX
0.740 0.770 18.80 19.55
0.250 0.270
6.85
6.35
0.145 0.175
4.44
3.69
0.015 0.021
0.53
0.39
0.040 0.070
1.77
1.02
0.100 BSC
2.54 BSC
0.050 BSC
1.27 BSC
0.008 0.015
0.38
0.21
0.110 0.130
3.30
2.80
0.295 0.305
7.74
7.50
10°
0°
10°
0°
0.020 0.040
1.01
0.51
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
9
1
MILLIMETERS
MIN
MAX
19.05 19.93
6.10
7.49
5.08
0.39
0.50
1.27 BSC
1.40
1.65
2.54 BSC
0.21
0.38
3.18
4.31
7.62 BSC
15°
0°
1.01
0.51
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
B
F
S
S
INCHES
MIN
MAX
0.750 0.785
0.240 0.295
0.200
0.015 0.020
0.050 BSC
0.055 0.065
0.100 BSC
0.008 0.015
0.125 0.170
0.300 BSC
15°
0°
0.020 0.040
J
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80 10.00
4.00
3.80
1.75
1.35
0.49
0.35
1.25
0.40
1.27 BSC
0.25
0.19
0.25
0.10
7°
0°
6.20
5.80
0.50
0.25
INCHES
MIN
MAX
0.386 0.393
0.150 0.157
0.054 0.068
0.014 0.019
0.016 0.049
0.050 BSC
0.008 0.009
0.004 0.009
0°
7°
0.229 0.244
0.010 0.019
MC54/74HC4051 MC74HC4052 MC54/74HC4053
OUTLINE DIMENSIONS
DW SUFFIX
PLASTIC SOIC PACKAGE
CASE 751G–02
ISSUE A
–A–
16
9
–B–
8X
P
0.010 (0.25)
1
B
M
M
8
16X
J
D
0.010 (0.25)
M
T A
S
B
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN
EXCESS OF D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
S
DIM
A
B
C
D
F
G
J
K
M
P
R
F
R X 45 C
–T–
14X
G
K
0.10 (0.004)
M
T U
V
S
S
S
ÉÉ
ÇÇ
ÇÇ
ÉÉ
ÇÇ
ÉÉ
K
K1
2X
L/2
16
9
J1
B
–U–
L
SECTION N–N
J
PIN 1
IDENT.
8
1
N
0.15 (0.006) T U
S
0.25 (0.010)
A
–V–
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH OR
GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER
SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED AT
DATUM PLANE -W-.
N
F
DETAIL E
–W–
C
0.10 (0.004)
–T– SEATING
PLANE
H
D
INCHES
MIN
MAX
0.400
0.411
0.292
0.299
0.093
0.104
0.014
0.019
0.020
0.035
0.050 BSC
0.010
0.012
0.004
0.009
0
7
0.395
0.415
0.010
0.029
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948F–01
ISSUE O
16X K REF
0.15 (0.006) T U
M
SEATING
PLANE
MILLIMETERS
MIN
MAX
10.15
10.45
7.40
7.60
2.35
2.65
0.35
0.49
0.50
0.90
1.27 BSC
0.25
0.32
0.10
0.25
0
7
10.05
10.55
0.25
0.75
G
DETAIL E
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
--1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0
8
INCHES
MIN
MAX
0.193
0.200
0.169
0.177
--0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.007
0.011
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0
8
MC54/74HC4051 MC74HC4052 MC54/74HC4053
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
MC74HC4051/D