TECHNICAL DATA POSITIVE VOLTAGE REGULATOR 3-TERMINAL 0.1A POSITIVE VOLTAGE REGULATORS IL78Lxx This series of fixed-voltage monolithic integrated-circuit voltage regulators is designed for a wide range of applications. These applications include on-card regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power-pass elements to make high current voltage regulators. Each of these regulators can deliver up to 100mA output current. The internal limiting and thermal shutdown features of these regulators make them essentially immune to overload. When used as a replacement for a zener diode-resistor combination, an effective improvement in output impedance can be obtained together with lower-bias current. Features • • • • • Output current Up to 100mA No External Components Internal Thermal Overload Protection Internal Short-Circuit Limiting Output Voltage of 5V, 6V, 8V, 9V, 10V, 12V, 15V, 18V and 24V Pin Configuration TO-92 SOT-89 SO-8 Absolute Maximum Ratings Characteristic Input voltage Symbol IL78L05 ~ IL78L10 IL78L12 ~ IL78L18 Value Unit 30 Vl IL78L24 35 V 40 Operating junction temperature Topr -40 ~ +150 Storage temperature Tstg -65 ~ +150 Soldering temperature and time Tsol 260/10sec °C Rev. 01 IL78LXX RECOMMENDED OPERATING CONDITIONS 78Lxx Input voltage, VI Min. Max. IL78L05 7 20 IL78L06 8 20 IL78L08 10.5 23 IL78L09 11.5 24 IL78L10 12.5 25 IL78L12 14.5 27 IL78L15 17.5 30 IL78L18 20.5 33 IL78L24 26.5 39 Output current, Io Operating virtual junction temperature, Tj -40 Unit V 100 ㎃ 125 ℃ TYPICAL APPLICATION Notes 1. To specify an output voltage, substitute voltage for "XX" 2. Bypass capacitors are recommended for optimum stability and transient response and should be located as close as possible to the regulators. Rev. 01 IL78LXX IL78L05 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=10V, lo=40mA (unless otherwise noted) Characteistic Output voltage ** Symbol Vout Test condition * Min Typ. Max. 25℃ 4.8 5 5.2 4.75 5 5.25 4.75 5 5.25 32 150 1㎃≤ Io≤ 40㎃ 7V≤ VI≤ Vmax Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 7≤ VI≤ 20V Line regulation Load regulation Reg line ㎷ 25℃ 8≤ VI≤ 20V 26 100 1㎃≤ Io≤ 100㎃ 15 60 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 8 30 3.8 6 IB ㎃ 125℃ 5.5 9≤ VI≤ 20V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 8≤ VI≤ 20V f=120㎐ 25℃ Dropout voltage VD 25℃ 41 42 ㎶ 49 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX IL78L06 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=12V, lo=40mA (unless otherwise noted) Characteistic Symbol Test condition * 25℃ Output voltage ** Vout 1㎃≤ Io≤ 40㎃ 8V≤ VI≤ 20V Min Typ. Max. 5.75 6 6.25 5.7 6 6.3 5.7 6 6.3 35 175 Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 8≤ VI≤ 20V Line regulation Load regulation Reg line ㎷ 25℃ 9≤ VI≤ 20V 29 125 1㎃≤ Io≤ 100㎃ 16 80 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 9 40 3.9 6 IB ㎃ 125℃ 5.5 9≤ VI≤ 20V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 9≤ VI≤ 19V f=120㎐ 25℃ Dropout voltage VD 25℃ 40 46 ㎶ 48 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX IL78L08 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=14V, lo=40mA (unless otherwise noted) Characteistic Symbol Test condition * 25℃ Output voltage ** Vout 1㎃≤ Io≤ 40㎃ 10.5V≤ VI≤ 23V Min Typ. Max. 7.7 8 8.3 7.6 8 8.4 7.6 8 8.4 42 175 Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 10.5≤ VI≤ 23V Line regulation Load regulation Reg line ㎷ 25℃ 11≤ VI≤ 23V 36 125 1㎃≤ Io≤ 100㎃ 18 80 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 10 40 4 6 IB ㎃ 125℃ 5.5 11≤ VI≤ 23V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 13≤ VI≤ 23V f=120㎐ 25℃ Dropout voltage VD 25℃ 37 54 ㎶ 46 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX IL78L09 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=14V, lo=40mA (unless otherwise noted) Characteistic Symbol Test condition * 25℃ Output voltage ** Vout 1㎃≤ Io≤ 40㎃ 12V≤ VI≤ 24V Min Typ. Max. 806 9 9.4 8.55 9 9.45 8.55 9 9.45 45 175 Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 12≤ VI≤ 24V Line regulation Load regulation Reg line ㎷ 25℃ 13≤ VI≤ 24V 40 125 1㎃≤ Io≤ 100㎃ 19 90 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 11 40 4.1 6 IB ㎃ 125℃ 5.5 13≤ VI≤ 24V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 13≤ VI≤ 23V f=120㎐ 25℃ Dropout voltage VD 25℃ 38 58 ㎶ 45 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX IL78L10 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=16V, lo=40mA (unless otherwise noted) Characteistic Symbol Test condition * 25℃ Output voltage ** Vout 1㎃≤ Io≤ 40㎃ 13V≤ VI≤ 25V Min Typ. Max. 9.6 10 10.4 9.5 10 10.5 9.5 10 10.5 51 175 Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 13≤ VI≤ 25V Line regulation Load regulation Reg line ㎷ 25℃ 14≤ VI≤ 25V 42 125 1㎃≤ Io≤ 100㎃ 20 90 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 11 40 4.2 6 IB ㎃ 125℃ 5.5 14≤ VI≤ 25V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 15≤ VI≤ 25V f=120㎐ 25℃ Dropout voltage VD 25℃ 37 62 ㎶ 44 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX IL78L12 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=17V, lo=40mA (unless otherwise noted) Characteistic Symbol Test condition * 25℃ Output voltage ** Vout 1㎃≤ Io≤ 40㎃ 14V≤ VI≤ 27V Min Typ. Max. 11.5 12 12.5 11.4 12 12.6 11.4 12 12.6 55 250 Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 14.5≤ VI≤ 27V Line regulation Load regulation Reg line ㎷ 25℃ 16≤ VI≤ 27V 49 200 1㎃≤ Io≤ 100㎃ 22 100 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 13 50 4.3 6.5 IB ㎃ 125℃ 6 16≤ VI≤ 27V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 15≤ VI≤ 25V f=120㎐ 25℃ Dropout voltage VD 25℃ 37 70 ㎶ 42 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX IL78L15 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=19V, lo=40mA (unless otherwise noted) Characteistic Symbol Test condition * 25℃ Output voltage ** Vout 1㎃≤ Io≤ 40㎃ 17.5V≤ VI≤ 30V Min Typ. Max. 14.4 15 15.6 14.25 15 15.75 14.25 15 15.75 65 300 Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 17.5≤ VI≤ 30V Line regulation Load regulation Reg line ㎷ 25℃ 19≤ VI≤ 30V 58 250 1㎃≤ Io≤ 100㎃ 25 150 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 15 75 4.2 6.5 IB ㎃ 125℃ 6 19≤ VI≤ 30V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 18.5≤ VI≤ 28.5V f=120㎐ 25℃ Dropout voltage VD 25℃ 37 82 ㎶ 44 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX IL78L18 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=23V, lo=40mA (unless otherwise noted) Characteistic Symbol Test condition * 25℃ Output voltage ** Vout 1㎃≤ Io≤ 40㎃ 20.5V≤ VI≤ 33V Min Typ. Max. 17.3 18 18.7 17.1 18 18.9 17.1 18 18.9 70 360 Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 20.5≤ VI≤ 33V Line regulation Load regulation Reg line ㎷ 25℃ 22≤ VI≤ 33V 64 300 1㎃≤ Io≤ 100㎃ 27 180 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 19 90 4.7 6.5 IB ㎃ 125℃ 6 22≤ VI≤ 33V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 21.5≤ VI≤ 31.5V f=120㎐ 25℃ Dropout voltage VD 25℃ 32 82 ㎶ 36 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX IL78L24 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, Vl=26V, lo=40mA (unless otherwise noted) Characteistic Symbol Test condition * 25℃ Output voltage ** Vout 1㎃≤ Io≤ 40㎃ 26.5V≤ VI≤ 39V Min Typ. Max. 23 24 25 22.8 24 25.2 22.8 24 25.2 95 480 Unit V -40 ~ 125℃ 1㎃≤Io≤ 70㎃ 26.5≤ VI≤ 39V Line regulation Load regulation Reg line ㎷ 25℃ 29≤ VI≤ 39V 78 400 1㎃≤ Io≤ 100㎃ 41 240 Reg load ㎷ 25℃ 1㎃≤ Io≤ 40㎃ 25℃ Bias current 28 120 4.8 6.5 IB ㎃ 125℃ 6 28≤ VI≤ 39V Bias current change △IB 1.5 ㎃ -40 ~ 125℃ 1㎃≤ Io≤ 40㎃ 0.1 Output noise voltage VN 10㎐≤ f≤ 100㎑ 25℃ Ripple rejection RR 27.5≤ VI≤ 37.5V f=120㎐ 25℃ Dropout voltage VD 25℃ 30 82 ㎶ 33 dB 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Rev. 01 IL78LXX • TO-92 Rev. 01 IL78LXX • SO-8 D SUFFIX SOIC (MS - 012AA) Dimension, mm A 8 5 B H 1 G P 4 D K MIN MAX A 4.8 5 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 R x 45 C -T- Symbol SEATING PLANE J F 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. M G 1.27 H 5.72 J 0° 8° K 0.1 0.25 M 0.19 0.25 P 5.8 6.2 R 0.25 0.5 Rev. 01 IL78LXX Rev. 01