Maxim MAX530BCNG 5v, low-power, parallel-input, voltage-output, 12-bit dac Datasheet

19-0168; Rev 3; 7/95
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
________________________Applications
Battery-Powered Data-Conversion Products
Minimum Component-Count Analog Systems
Digital Offset/Gain Adjustment
Industrial Process Control
Arbitrary Function Generators
Automatic Test Equipment
Microprocessor-Controlled Calibration
________________Functional Diagram
REFOUT
18
REFIN
13
ROFS
22
AGND
20
17
A0
A1
12-BIT DAC LATCH
8
9
CS 11
WR 10
LDAC
MAX530
15
CONTROL
LOGIC
NBL
INPUT
LATCH
♦
♦
♦
♦
______________Ordering Information
PART
TEMP. RANGE
PIN-PACKAGE
ERROR
(LSB)
MAX530ACNG
0°C to +70°C
24 Narrow Plastic DIP
±1/2
MAX530BCNG 0°C to +70°C 24 Narrow Plastic DIP
MAX530ACWG 0°C to +70°C 24 Wide SO
MAX530BCWG 0°C to +70°C 24 Wide SO
MAX530ACAG
0°C to +70°C 24 SSOP
MAX530BCAG
0°C to +70°C 24 SSOP
MAX530BC/D
0°C to +70°C Dice*
Ordering Information continued on last page.
* Dice are tested at TA = +25°C, DC parameters only.
±1
±1/2
±1
±1/2
±1
±1
__________________Pin Configuration
D1/D9 1
24 D0/D8
D2/D10 2
23 VDD
D3/D11 3
22 ROFS
D4 4
23
POWER-ON
RESET
CLR
VOUT
DAC LATCH
14
♦
♦
Buffered Voltage Output
Internal 2.048V Voltage Reference
Operates from Single +5V or Dual ±5V Supplies
Low Power Consumption:
250µA Operating Current
40µA Shutdown-Mode Current
SSOP Package Saves Space
Relative Accuracy: ±1/2 LSB Max Over
Temperature
Guaranteed Monotonic Over Temperature
4-Quadrant Multiplication with No External
Components
Power-On Reset
Double-Buffered Parallel Logic Inputs
TOP VIEW
21 RFB
2.048V
REFERENCE
REFGND
____________________________Features
♦
♦
♦
♦
NBM
INPUT
LATCH
16
24 1 2 3 4 5 6 7
D4 D6
D0/D8 D2/D10
D1/D9 D3/D11 D5 D7
NBH
INPUT
LATCH
12
19
VDD
D5 5
21 RFB
MAX530
20 VOUT
DGND
D6 6
19 VSS
VSS
D7 7
18 REFOUT
A0 8
17 REFGND
A1 9
16 LDAC
WR 10
15 CLR
CS 11
14 AGND
DGND 12
13 REFIN
DIP/SO/SSOP
________________________________________________________________ Maxim Integrated Products
Call toll free 1-800-998-8800 for free samples or literature.
1
MAX530
_______________General Description
The MAX530 is a low-power, 12-bit, voltage-output digital-to-analog converter (DAC) that uses single +5V or
dual ±5V supplies. This device has an on-chip voltage
reference plus an output buffer amplifier. Operating current is only 250µA from a single +5V supply, making it
ideal for portable and battery-powered applications. In
addition, the SSOP (Shrink-Small-Outline-Package) measures only 0.1 square inches, using less board area than
an 8-pin DIP. 12-bit resolution is achieved through laser
trimming of the DAC, op amp, and reference. No further
adjustments are necessary.
Internal gain-setting resistors can be used to define a
DAC output voltage range of 0V to +2.048V, 0V to
+4.096V, or ±2.048V. Four-quadrant multiplication is possible without the use of external resistors or op amps. The
parallel logic inputs are double buffered and are compatible with 4-bit, 8-bit, and 16-bit microprocessors. For DACs
with similar features but with a serial data interface, refer
to the MAX531/MAX538/MAX539 data sheet.
MAX530
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
ABSOLUTE MAXIMUM RATINGS
VOUT to AGND (Note 1) .............................................. VSS, VDD
Continuous Current, Any Input ........................................±20mA
Continuous Power Dissipation (TA = +70°C)
Narrow Plastic DIP (derate 13.33mW/°C above +70°C)......1067mW
Wide SO (derate 11.76mW/°C above +70°C) .......... 941mW
SSOP (derate 8.00mW/°C above +70°C) ..................640mW
Operating Temperature Ranges:
MAX530_C_ _ ...................................................0°C to +70°C
MAX530_E_ _ ................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +165°C
Lead Temperature (soldering, 10sec ) .......................... +300°C
VDD to DGND and VDD to AGND ................................-0.3V, +6V
VSS to DGND and VSS to AGND .................................-6V, +0.3V
VDD to VSS ............................................................... -0.3V, +12V
AGND to DGND........................................................-0.3V, +0.3V
REFGND to AGND........................................-0.3V, (VDD + 0.3V)
Digital Input Voltage to DGND ................... -0.3V, (VDD + 0.3V)
REFIN .................................................(VSS - 0.3V), (VDD + 0.3V)
REFOUT .............................................(VSS - 0.3V), (VDD + 0.3V)
REFOUT to REFGND ................................... -0.3V, (VDD + 0.3V)
RFB ...................................................(VSS - 0.3V), (VDD + 0.3V)
ROFS .................................................(VSS - 0.3V), (VDD + 0.3V)
Note 1: The output may be shorted to VDD, VSS, DGND, or AGND if the continuous package power dissipation and current ratings
are not exceeded. Typical short-circuit currents are 20mA.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Single +5V Supply
(VDD = 5V ±10%, VSS = 0V, AGND = DGND = REFGND = 0V, REFIN = 2.048V (external), RFB = ROFS = VOUT, CREFOUT = 33µF,
RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE
Resolution
N
12
Relative Accuracy
INL
VDD = 5V (Note 2)
Differential Nonlinearity
DNL
Guaranteed monotonic
Unipolar Offset Error
VOS
VDD = 5V
Unipolar Offset
Temperature Coefficient
TCVOS
Unipolar Offset-Error
Power-Supply Rejection
PSRR
Gain Error (Note 2)
GE
±0.5
MAX530BC/BE
±1
MAX530_C/E
0
1
4.5V ≤ VDD ≤ 5.5V (Note 3)
DAC latch = all 1s,
VOUT < VDD - 0.4V
(Note 2)
0.4
MAX530_C/E
LSB
8
LSB
ppm/°C
1
LSB/V
±1
LSB
1
PSRR
4.5V ≤ VDD ≤ 5.5V (Note 3)
0.4
LSB
±1
3
Gain-Error Temperature Coefficient
Gain-Error Power-Supply Rejection
Bits
MAX530AC/AE
ppm/°C
1
LSB/V
DAC VOLTAGE OUTPUT (VOUT)
Output Voltage Range
0
VOUT = 2V, load regulation ≤ ±1LSB
Resistive Load
DC Output Impedance
Short-Circuit Current
VDD - 0.4
2
ISC
V
kΩ
0.2
Ω
20
mA
REFERENCE INPUT (REFIN)
Reference Input Range
0
Reference Input Resistance
Code dependent, minimum at code 555hex
40
Reference Input Capacitance
Code dependent (Note 4)
10
AC Feedthrough
(Note 5)
2
VDD - 2
V
kΩ
50
-80
_______________________________________________________________________________________
pF
dB
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
(VDD = 5V ±10%, VSS = 0V, AGND = DGND = REFGND = 0V, REFIN = 2.048V (external), RFB = ROFS = VOUT, CREFOUT = 33µF,
RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
TA = +25°C
2.024
2.048
2.072
MAX530BC
2.017
2.079
MAX530BE
2.013
2.083
UNITS
REFERENCE OUTPUT (REFOUT)
Reference Tolerance
VREFOUT
Reference Output Resistance
RREFOUT
Power-Supply Rejection Ratio
PSRR
Noise Voltage
en
Temperature Coefficient
Minimum Required External
Capacitor
VDD = 5.0V
(Note 8)
4.5V ≤ VDD ≤ 5.5V
0.1Hz to 10kHz
400
MAX530AC/AE
30
MAX530BC/BE
30
CMIN
V
2
Ω
300
µV/V
µVp-p
50
3.3
ppm/°C
µF
DYNAMIC PERFORMANCE
Voltage Output Slew Rate
TA = +25°C
Voltage Output Settling Time
To ±0.5LSB, VOUT = 2V
25
µs
Digital Feedthrough
WR = VDD, digital inputs all 1s to all 0s
5
nV-s
Unity gain (Note 5)
68
Gain = 2 (Note 5)
68
Signal-to-Noise Plus
Distortion Ratio
SINAD
0.15
0.25
V/µs
dB
DIGITAL INPUTS (D0-D7, LDAC, CLR, CS, WR, A0, A1)
Logic High Input
VIH
Logic Low Input
VIL
Digital Leakage Current
2.4
V
VIN = 0V or VDD
Digital Input Capacitance
0.8
V
±1
µA
8
pF
POWER SUPPLIES
Positive Supply-Voltage Range
VDD
(Note 6)
Positive Supply Current
IDD
Outputs unloaded, all digital inputs = 0V or VDD
4.5
250
5.5
V
400
µA
SWITCHING CHARACTERISTICS
Address to WR Setup
tAWS
5
ns
Address to WR Hold
tAWH
5
ns
CS to WR Setup
tCWS
0
ns
CS to WR Hold
0
ns
Data to WR Setup
tCWH
tDS
45
ns
Data to WR Hold
tDH
0
ns
WR Pulse Width
tWR
45
ns
tLDAC
45
ns
tCLR
45
LDAC Pulse Width
CLR Pulse Width
Internal Power-On Reset
Pulse Width
tPOR
(Note 4)
ns
1.3
10
µs
_______________________________________________________________________________________
3
MAX530
ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued)
MAX530
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
ELECTRICAL CHARACTERISTICS—Dual ±5V Supplies
(VDD = 5V ±10%, VSS = -5V ±10%, AGND = DGND = REFGND = 0V, REFIN = 2.048V (external), RFB = ROFS = VOUT,
CREFOUT = 33µF, RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE
Resolution
N
12
Relative Accuracy
INL
VDD = 5V, VSS = -5V
Differential Nonlinearity
DNL
Guaranteed monotonic
Bipolar Offset Error
VOS
VDD = 5V, VSS = -5V
Bipolar Offset
Temperature Coefficient
TCVOS
Bipolar Offset-Error
Power-Supply Rejection
PSRR
Gain Error
Bits
MAX530AC/AE
±0.5
MAX530BC/BE
±1.5
MAX530_C/E
0
0.4
MAX530_C/E
Gain-Error Temperature Coefficient
TC
Gain-Error Power-Supply Rejection
PSRR
±1
LSB
±8
LSB
3
4.5V ≤ VDD ≤ 5.5V
-5.5V ≤ VSS ≤ -4.5V (Note 3)
ppm/°C
1
±1
1
4.5V ≤ VDD ≤ 5.5V, -5.5V ≤ VSS ≤ -4.5V (Note 3)
0.4
LSB
LSB/V
LSB
ppm/°C
1
LSB/V
DAC VOLTAGE OUTPUT (VOUT)
Output Voltage Range
VSS + 0.4
VOUT = 2V, load regulation ≤ ±1LSB
Resistive Load
DC Output Impedance
Short-Circuit Current
VDD - 0.4
2
ISC
V
kΩ
0.2
Ω
20
mA
REFERENCE INPUT (REFIN)
Reference Input Range
VSS + 2
Reference Input Resistance
Code dependent, minimum at code 555hex
40
Reference Input Capacitance
Code dependent (Note 4)
10
AC Feedthrough
(Note 5)
VDD - 2
V
kΩ
50
-80
pF
dB
REFERENCE OUTPUT (REFOUT)—Specifications are identical to those under Single +5V Supply
DYNAMIC PERFORMANCE—Specifications are identical to those under Single +5V Supply
DIGITAL INPUTS (D0-D7, LDAC, CLR, CS, WR, A0, A1)—Specifications are identical to those under Single +5V Supply
POWER SUPPLIES
Positive Supply Voltage
VDD
(Note 6)
4.5
5.5
Negative Supply Voltage
VSS
(Note 7)
-5.5
-4.5
V
Positive Supply Current
IDD
Outputs unloaded, all digital inputs = 0V or VDD
250
400
µA
Negative Supply Current
ISS
Outputs unloaded, all digital inputs = 0V or VDD
150
200
µA
SWITCHING CHARACTERISTICS—Specifications are identical to those under Single +5V Supply
4
_______________________________________________________________________________________
V
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
MAX530
ELECTRICAL CHARACTERISTICS—Dual ±5V Supplies (continued)
(VDD = 5V ±10%, VSS = -5V ±10%, AGND = DGND = REFGND = 0V, REFIN = 2.048V (external), RFB = ROFS = VOUT,
CREFOUT = 33µF, RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted.)
Note 2: In single supply, INL and GE are calculated from code 11 to code 4095.
Note 3: Zero Code, Bipolar and Gain Error PSRR are input referred specifications. In Unity Gain, the specification is 500µV.
In Gain = 2 and Bipolar modes, the specification is 1mV.
Note 4: Guaranteed by design.
Note 5: REFIN = 1kHz, 2.0Vp-p.
Note 6: For specified performance, VDD = 5V ±10% is guaranteed by PSRR tests.
Note 7: For specified performance, VSS = -5V ±10% is guaranteed by PSRR tests.
Note 8: Tested at IOUT = 100µA. The reference can typically source up to 5mA (see Typical Operating Characteristics).
__________________________________________Typical Operating Characteristics
(TA = +25°C, single supply (+5V), unity gain, code = all 1s, unless otherwise noted).
INTEGRAL NONLINEARITY vs.
DIGITAL INPUT CODE (11–4095)
14
-1.00
-1.25
-0.25
-0.50
SINGLE
SUPPLY
2
6
4
8
10
4
2
0
512 1024 1536 2048 2560 3072 3584 4095
0.2
0.4
0.6
0.8
DIGITAL INPUT CODE (DECIMAL)
OUTPUT PULL-DOWN VOLTAGE (V)
OUTPUT SOURCE CAPABILITY vs.
OUTPUT PULL-UP VOLTAGE
ANALOG FEEDTHROUGH vs.
FREQUENCY
REFERENCE VOLTAGE vs.
TEMPERATURE
-110
MAX531-4
7
-100
ANALOG FEEDTHROUGH (dB)
OUTPUT SOURCE CAPABILITY (mA)
6
DIGITAL INPUT CODE (DECIMAL)
8
6
5
4
3
2
1
-90
-80
-70
REFIN = 2Vp-p
-60
-50
-40
-30
2
3
4
OUTPUT PULL-UP VOLTAGE (V)
5
2.050
CODE = ALL 0s,
DUAL SUPPLIES (±5V)
2.045
0
1
2.055
1.0
-20
-10
0
0
8
0
11
12
12
10
MAX531-6
0
0
MAX531-5
0
REFERENCE VOLTAGE (V)
INTEGRAL NONLINEARITY (LSB)
DUAL
SUPPLIES
OUTPUT SINK CAPABILITY (mA)
16
MAX530-1
0.25
0.25
MAX531-3
OUTPUT SINK CAPABILITY vs.
OUTPUT PULL-DOWN VOLTAGE
INTEGRAL NONLINEARITY (LSB)
INTEGRAL NONLINEARITY vs.
DIGITAL INPUT CODE (0–11)
1
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
-60 -40 -20
0 20
40 60 80 100 120 140
TEMPERATURE (°C)
_______________________________________________________________________________________
5
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
MAX530
____________________________Typical Operating Characteristics (continued)
(TA = +25°C, single supply (+5V), unity gain, code = all 1s, unless otherwise noted).
-2
270
260
-4
-6
-8
250
DUAL SUPPLIES (±5V)
-10
240
REFIN = 4Vp-p
SIGNAL-TO-NOISE RATIO (dB)
0
280
80
MAX531-8
MAX530-7
REFIN = 4Vp-p
2
GAIN (dB)
-20
0
20
40
60
80 100
TEMPERATURE (°C)
MAX530-10
180
100
1k
10k
10
100k
0
0
PHASE
-100
150
REFGND = VDD
50
-200
100k
2.0480
2.0475
200
100
10k
REFERENCE OUTPUT VOLTAGE
vs. REFERENCE LOAD CURRENT
REFGND = AGND
GAIN
1k
100
FREQUENCY (Hz)
250
SUPPLY CURRENT (µA)
GAIN (dB)
-100
DUAL SUPPLIES (±5V)
SUPPLY CURRENT vs. REFIN
PHASE SHIFT (Degrees)
(G = 2)
(G = 1)
30
20
FREQUENCY (Hz)
GAIN AND PHASE vs.
FREQUENCY
-200
50
40
0
1
REFERENCE OUTPUT (V)
-40
-14
MAX530-14
-60
60
10
-12
230
70
MAX530-15
SUPPLY CURRENT (µA)
290
AMPLIFIER SIGNAL-TO- NOISE RATIO
GAIN vs. FREQUENCY
4
MAX531-9
SUPPLY CURRENT vs. TEMPERATURE
300
2.0470
2.0465
2.0460
2.0455
REFIN = EXTERNAL
-180
-300
1
10
100
800
0
2.0450
0
FREQUENCY (kHz)
50 100 150 200 250 300 350 400 450 500
REFIN (mV)
DIGITAL FEEDTHROUGH
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
REFERENCE LOAD CURRENT (mA)
SETTLING TIME (RISING)
SETTLING TIME (FALLING)
A
A
A
B
B
B
2µs/div
A: D0...D7 = 100kHz, 4Vp-p
B: VOUT, 10mV/div
LDAC = CS = HIGH
6
5µs/div
A: DIGITAL INPUTS RISING EDGE,
B: VOUT, NO LOAD, 1V/div
DUAL SUPPLY (±5V)
LDAC = LOW
BIPOLAR CONFIGURATION
VREFIN = 2V
5µs/div
A: DIGITAL INPUTS FALLING EDGE, 5V/div
B: VOUT, NO LOAD, 1V/div
DUAL SUPPLY (±5V)
LDAC = LOW
BIPOLAR CONFIGURATION
VREFIN = 2V
_______________________________________________________________________________________
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
PIN
NAME
FUNCTION
1
D1/ D9
D1 Input Dta, when A0 = 0 and A1 = 1, or D9 Input when A0 = A1 = 1*
2
D2/ D10
D2 Input Dta, when A0 = 0 and A1 = 1, or D10 Input when A0 = A1 = 1*
3
D3/ D11
D3 Input Dta, when A0 = 0 and A1 = 1, or D11 (MSB) Input when A0 = A1 =1*
4
D4
D4 Input Dta, or tie to D0 and multiplex when A0 = 1 and A1 = 0*
5
D5
D5 Input Dta, or tie to D1 and multiplex when A0 = 1 and A1 = 0*
6
D6
D6 Input Dta, or tie to D2 and multiplex when A0 = 1 and A1 = 0*
7
D7
D7 Input Dta, or tie to D3 and multiplex when A0 = 1 and A1 = 0*
8
A0
Address Line A0. With A1, used to multiplex 4 of 12 data lines to load low (NBL), middle (NBM),
and high (NBH) 4-bit nibbles. (12 bits can also be loaded as 8+4.)
9
A1
Address Line A1. Set A0 = A1 = 0 for NBL and NBM, A0 = 0 and A1 = 1 for NBL, A0 = 1 and
A1 = 0 for NBM, or A0 = A1 = 1 for NBH. See Table 2 for complete input latch addressing.
10
WR
Write Input (active low). Used with CS to load data into the input latch selected by A0 and A1.
11
CS
Chip Select (active low). Enables addressing and writing to this chip from common bus lines.
12
DGND
Digital Ground
13
REFIN
Reference Input. Input for the R-2R DAC. Connect an external reference to this pin or a jumper to
REFOUT (pin 18) to use the internal 2.048V reference.
14
AGND
Analog Ground
15
CLR
16
LDAC
Load DAC Input (active low). Driving this asynchronous input low transfers the contents of the input
latch to the DAC latch and updates VOUT.
17
REFGND
Reference Ground must be connected to AGND when using the internal reference. Connect to VDD
to disable the internal reference and save power.
18
REFOUT
Reference Output. Output of the internal 2.048V reference. Tie to REFIN to drive the R-2R DAC.
19
VSS
20
VOUT
21
RFB
22
ROFS
23
VDD
24
D0/D8
Clear (active low). A low on CLR resets the DAC latches to all 0s.
Negative Power Supply. Usually ground for single-supply or -5V for dual-supply operation.
Voltage Output. Op-amp buffered DAC output.
Feedback Pin. Op-amp feedback resistor. Always connect to VOUT.
Offset Resistor Pin. Connect to VOUT for G = 1, to AGND for G = 2, or to REFIN for bipolar output.
Positive Power Supply (+5V)
D0 (LSB) Input Dta when A0 = 0 and A1 = 1, or D8 Input when A0 = A1= 1*
* This applies to 4 + 4 + 4 input loading mode. See Table 2 for 8 + 4 input loading mode.
_______________________________________________________________________________________
7
MAX530
______________________________________________________________Pin Description
MAX530
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
________________Detailed Description
The MAX530 consists of a parallel-input logic interface, a
12-bit R-2R ladder, a reference, and an op amp. The
Functional Diagram shows the control lines and signal
flow through the input data latch to the DAC latch, as well
as the 2.048V reference and output op amp. Total supply
current is typically 250µA with a single +5V supply. This
circuit is ideal for battery-powered, microprocessor-controlled applications where high accuracy, no adjustments,
and minimum component count are key requirements.
R-2R Ladder
The MAX530 uses an “inverted” R-2R ladder network with
a BiCMOS op amp to convert 12-bit digital data to analog
voltage levels. Figure 1 shows a simplified diagram of the
R-2R DAC and op amp. Unlike a standard DAC, the
MAX530 uses an “inverted” ladder network. Normally, the
REFIN pin is the current output of a standard DAC and
would be connected to the summing junction, or virtual
ground, of an op amp. In this standard DAC configura-
tion, however, the output voltage would be the inverse of
the reference voltage. The MAX530’s topology makes the
ladder output voltage the same polarity as the reference
input, which makes the device suitable for single-supply
operation. The BiCMOS op amp is then used to buffer,
invert, or amplify the ladder signal.
Ladder resistors are nominally 80kΩ to conserve power
and are laser trimmed for gain and linearity. The input
impedance at REFIN is code dependent. When the DAC
register is all 0s, all rungs of the ladder are grounded
and REFIN is open or no load. Maximum loading (minimum REFIN impedance) occurs at code 010101... or
555hex. Minimum reference input impedance at this
code is guaranteed to be not less than 40kΩ.
The REFIN and REFOUT pins allow the user to choose
between driving the R-2R ladder with the on-chip reference or an external reference. REFIN may be below analog ground when using dual supplies. See the External
Reference and Four-Quadrant Multiplication sections for
more information.
Internal Reference
2R
2R
MAX530
R
2R
*
2R
RFB
R
2R
ROFS
R
2R
LSB
2R
VOUT
OUTPUT
BUFFER
MSB
R = 80kΩ
REFIN
AGND
REFOUT
LSB
DAC LATCH
MSB
NBL
INPUT
LATCH
NBM
INPUT
LATCH
NBH
INPUT
LATCH
CLR
2.048V
REFGND
D4 D6
D0/D8
D2/D10
D1/D9
D5 D7
D3/D11
*SHOWN FOR ALL 1s
The on-chip reference is laser trimmed to generate
2.048V at REFOUT. The output stage can source and
sink current so REFOUT can settle to the correct voltage quickly in response to code-dependent loading
changes. Typically source current is 5mA and sink current is 100µA.
REFOUT connects the internal reference to the R-2R
DAC ladder at REFIN. The R-2R ladder draws 50µA
maximum load current. If any other connection is made
to REFOUT, ensure that the total load current is less
than 100µA to avoid gain errors.
A separate REFGND pin is provided to isolate reference currents from other analog and digital ground
currents. To achieve specified noise performance, connect a 33µF capacitor from REFOUT to REFGND (see
Figure 2). Using smaller capacitance values increases
noise, and values less than 3.3µF may compromise the
reference’s stability. For applications requiring the lowest noise, insert a buffered RC filter between REFOUT
and REFIN. When using the internal reference,
REFGND must be connected to AGND. In applications
not requiring the internal reference, connect REFGND
to VDD, which shuts down the reference and saves typically 100µA of VDD supply current.
Figure 1. Simplified MAX530 DAC Circuit
8
_______________________________________________________________________________________
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
TOTAL
REFERERNCE
NOISE
CS
CREFOUT
REFERENCE NOISE (µVRMS)
250
1.6
CREFOUT = 3.3µF
1.4
200
1.2
1.0
150
0.8
100
0.6
0.4
50
CREFOUT = 47µF
0
0.1
1
10
100
REFERENCE NOISE (mVp-p)
1.8
SINGLE POLE ROLLOFF
MAX531-FIG02
TEK 7A22
300
0.2
0.0
1000
FREQUENCY (kHz)
Figure 2. Reference Noise vs. Frequency
Output Buffer
The output amplifier uses a folded cascode input stage
and a type AB output stage. Large output devices with
low series resistance allow the output to swing to
ground in single-supply operation. The output buffer is
unity-gain stable. Input offset voltage and supply current are laser trimmed. Settling time is 25µs to 0.01% of
final value. The output is short-circuit protected and
can drive a 2kΩ load with more than 100pF of load
capacitance. The op amp may be placed in unity-gain
(G = 1), in a gain of two (G = 2), or in a bipolar-output
mode by using the ROFS and RFB pins. These pins are
used to define a DAC output voltage range of 0V to
+2.048V, 0V to +4.096V or ±2.048V, by connecting
ROFS to VOUT, GND, or REFIN. RFB is always connected to VOUT. Table 1 summarizes ROFS usage.
Table 1. ROFS Usage
ROFS
CONNECTED TO:
DAC OUTPUT
RANGE
OP-AMP
GAIN
VOUT
0V to 2.048V
G=1
AGND
0V to 4.096V
G=2
REFIN
-2.048V to +2.048V
Bipolar
An external reference in the range (V SS + 2V) to
(VDD - 2V) may be used with the MAX530 in dual-supply, unity-gain operation. In single-supply, unity-gain
operation, the reference must be positive and may not
exceed (VDD - 2V). The reference voltage determines
the DAC’s full-scale output. Because of the codedependent nature of reference input impedances, a
high-quality, low-output-impedance amplifier (such as
the MAX480 low-power, precision op amp) should be
used to drive REFIN.
If an upgrade to the internal reference is required, the
2.5V MAX873A is ideal: ±15mV initial accuracy,
7ppm/°C (max) temperature coefficient.
Power-On Reset
An internal power-on reset (POR) circuit forces the
DAC register to reset to all 0s when VDD is first applied.
The POR pulse is typically 1.3µs; however, it may take
2ms for the internal reference to charge its large filter
capacitor and settle to its trimmed value.
In addition to POR , a clear (CLR) pin, when held low,
sets the DAC register to all 0s. CLR operates asynchronously and independently from chip select (CS). With
the DAC input at all 0s, the op-amp output is at zero for
unity-gain and G = 2 configurations, but it is at -VREF
for the bipolar configuration.
Shutdown Mode
The MAX530 is designed for low power consumption.
Understanding the circuit allows power consumption
management for maximum efficiency. In single-supply
mode (VDD = +5V, VSS = GND) the initial supply current is typically only 160µA, including the reference, op
amp, and DAC. This low current occurs when the
power-on reset circuit clears the DAC to all 0s and
forces the op-amp output to zero (unipolar mode only).
See the Supply Current vs. REFIN graph in the Typical
Operating Characteristics. Under this condition, there
is no internal load on the reference (DAC = 000hex,
REFIN is open circuit) and the op amp operates at its
minimum quiescent current. The CLR signal resets the
MAX530 to these same conditions and can be used to
control a power-saving mode when the DAC is not
being used by the system.
Note: Assumes RFB = VOUT and REFIN = REFOUT = 2.048V
_______________________________________________________________________________________
9
MAX530
External Reference
RS
REFOUT
MAX530
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
REFOUT
REFIN
ROFS
33µF
2.048V
REFERENCE
RFB
REFGND
VOUT
2N7002
AGND
DGND
DAC
POWER-ON
RESET
MAX530
VDD
12-BIT DAC LATCH
CLR
+5V
VSS
NBL
INPUT
LATCH
A0
A1
CONTROL
LOGIC
NBM
INPUT
LATCH
NBH
INPUT
LATCH
CS
WR
LDAC
D4 D6
D0/D8
D2/D10
D1/D9
D5 D7
D3/D11
Figure 3. Low-Current Shutdown Mode
An additional 110µA of supply current can be saved
when the internal reference is not used by connecting
REFGND to VDD. A low on resistance N-channel FET,
such as the 2N7002, can be used to turn off the internal
reference to create a shutdown mode with minimum
current drain (Figure 3). When CLR is high, the transistor pulls REFGND to AGND and the reference and DAC
operate normally. When CLR goes low, REFGND is
pulled up to VDD and the reference is shut down. At the
same time, CLR resets the DAC register to all 0s, and
the op-amp output goes to 0V for unity-gain and G = 2
Table 2. Input Latch Addressing
CLR CS WR LDAC
X
X
A0
X
A1
X
H
X
H
X
X
No Operation
X
H
H
X
X
No Operation
H
L
L
H
H
H
NBH (D8-D11)
H
L
L
H
H
L
NBM (D4-D7)
H
L
L
H
L
H
NBL (D0-D3)
H
H
H
L
X
X
Update DAC Only
H
H
L
L
L
L
X
L
L
H
L
H
DAC NOT UPDATED
NBH and Update DAC
L
X
H
H
10
DATA UPDATED
Reset DAC Latches
modes. This reduces the total single-supply operating
current from 250µA (400µA max) to typically 40µA in
shutdown mode.
A small error voltage is added to the reference output
by the reference current flowing through the N-channel
pull-down transistor. The switch’s on resistance should
be less than 5Ω. A typical reference current of 100µA
would add 0.5mV to REFOUT. Since the reference current and on resistance increase with temperature, the
overall temperature coefficient will degrade slightly.
As data is loaded into the DAC and the output moves
above GND, the op-amp quiescent current increases to
its nominal value and the total operating current averages 250µA. Using dual supplies (±5V), the op amp is
fully biased continuously, and the VDD supply current is
more constant at 250µA. The VSS current is typically
150µA.
The MAX530 logic inputs are compatible with TTL and
CMOS logic levels. However, to achieve the lowest
power dissipation, drive the digital inputs with rail-to-rail
CMOS logic. With TTL logic levels, the power requirement increases by a factor of approximately 2.
______________________________________________________________________________________
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
MAX530
ADDRESS BUS VALID
VIH
A0-A1
VIL
tAWH
CS
tCWS
tCWH
WR
tAWS
tWR
tDS
DATA BITS
(8-BIT BYTE OR
4-BIT NIBBLE)
CLR
tDH
VIH
VIL
DATA BUS
VALID
tCLR
LDAC
NOTE: TIMING MEASUREMENT REFERENCE LEVEL IS
VIH + VIL
2
tLDAC
Figure 4. MAX530 Write-Cycle Timing Diagram
Parallel Logic Interface
Designed to interface with 4-bit, 8-bit, and 16-bit microprocessors (µPs), the MAX530 uses 8 data pins and
double-buffered logic inputs to load data as 4 + 4 + 4
or 8 + 4. The 12-bit DAC latch is updated simultaneously through the control signal LDAC. Signals A0, A1,
WR, and CS select which input latches to update. The
12-bit data is broken down into nibbles (NB); NBL is
the enable signal for the lowest 4 bits, NBM is the
enable for the middle 4 bits, and NBH is the enable for
the highest and most significant 4 bits. Table 2 lists the
address decoding scheme.
Refer to Figure 4 for the MAX530 write-cycle timing
diagram.
Figure 5 shows the circuit configuration for a 4-bit µP
application. Figure 6 shows the corresponding timing
sequence. The 4 low bits (D0-D3) are connected in parallel to the other 4 bits (D4-D7) and then to the µP bus.
Address lines A0 and A1 enable the input data latches
for the high, middle, or low data nibbles. The µP sends
chip select (CS) and write (WR) signals to latch in each of
three nibbles in three cycles when the data is valid.
Figure 7 shows a typical interface to an 8-bit or a 16-bit
µP. Connect 8 data bits from the data bus to pins D0-D7
on the MAX530. With LDAC held high, the user can load
NBH or NBL + NBM in any order. Figure 8a shows the
corresponding timing sequence. For fastest throughput,
use Figure 8b’s sequence. Address lines A0 and A1 are
tied together and the DAC is loaded in 2 cycles as 8 + 4.
In this scheme, with LDAC held low, the DAC latch is
transparent. Always load NBL and NBM first, followed by
NBH.
LDAC is asynchronous with respect to WR. If LDAC is
brought low before or at the same time WR goes high,
LDAC must remain low for at least 50ns to ensure the correct data is latched. Data is latched into DAC registers on
LDAC’s rising edge.
______________________________________________________________________________________
11
MAX530
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
D0-D3
DATA BUS
D0-D3
D0-D3
FROM
SYSTEM
RESET
D0-D3
CLR
D4-D7
A0, A1
MC6800
D0-D7
DATA BUS
D0-D7
FROM
SYSTEM
RESET
CLR
MAX530
MAX530
A0-A1
MC6809
CS LDAC
WR
D0-D7
02
CS LDAC
WR
E
EN
R/W
ADDRESS BUS
A0-A15
A0, A1
DECODER
R/W
EN
A0-A15 ADDRESS BUS
A13-A15
A0
DECODER
A13-A15
Figure 7. 8-Bit and 16-Bit µP Interface
Figure 5. 4-Bit µP Interface
A0 = 1, A1 = 1
NBH
NBM
A0 = 1, A1 = 0
NBL
A0 = 0, A1 = 1
CS
WR
LDAC
DAC UPDATE
Figure 6. 4-Bit µP Timing Sequence
NBH
A0 = A1 = 1
NBL & NBM
A0 = A1 = 0
CS
WR
LDAC
DAC UPDATE
Figure 8a. 8-Bit and 16-Bit µP Timing Sequence Using LDAC
12
______________________________________________________________________________________
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
MAX530
A0 = A1 = 0
NBL & NBM
A0 = A1 = 1
NBH
CS
WR
LDAC = 0 (DAC LATCH IS TRANSPARENT)
DAC UPDATE
Figure 8b. 8-Bit and 16-Bit µP Timing Sequence with LDAC = 0
Unipolar Configuration
The MAX530 is configured for a 0V to +2.048V unipolar
output range by connecting ROFS and RFB to VOUT
(Figure 9). The converter operates from either single or
dual supplies in this configuration. See Table 3 for the
DAC-latch contents (input) vs. the analog VOUT (output).
In this range, 1LSB = REFIN (2 -12).
A 0V to 4.096V unipolar output range is set up by connecting ROFS to AGND and RFB to VOUT (Figure 10).
Table 4 shows the DAC-latch contents vs. VOUT. The
MAX530 operates from either single or dual supplies in
this mode. In this range, 1LSB = (2)(REFIN)(2 -12) =
(REFIN)(2 -11).
+5V
REFIN
+5V
VDD
REFIN
ROFS
REFOUT
VDD
REFOUT
33µF
33µF
MAX530
AGND
MAX530
ROFS
RFB
RFB
AGND
DGND
VOUT
VOUT
REFGND
VOUT
DGND
VOUT
REFGND
VSS
G=1
0V TO -5V
Figure 9. Unipolar Configuration (0V to +2.048V Output)
VSS
G=2
0V TO -5V
Figure 10. Unipolar Configuration (0V to +4.096V Output)
______________________________________________________________________________________
13
MAX530
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
Table 3. Unipolar Binary Code Table
(0V to VREFIN Output), Gain = 1
OUTPUT
INPUT
OUTPUT
INPUT
1111
1111
1111
(VREFIN)
4095
4096
1111
1111
1111
+2 (VREFIN)
4095
4096
1000
0000
0001
(VREFIN)
2049
4096
1000
0000
0001
+2 (VREFIN)
2049
4096
1000
0000
0000
1000
0000
0000
+2 (VREFIN)
2048
= +VREFIN
4096
0111
1111
1111
(VREFIN)
2047
4096
0111
1111
1111
+2 (VREFIN)
2047
4096
0000
0000
0001
(VREFIN)
1
4096
0000
0000
0001
+2 (VREFIN)
1
4096
0000
0000
0000
0000
0000
0000
(VREFIN)
2048
= +VREFIN/2
4096
OV
Bipolar Configuration
A -VREFIN to +VREFIN bipolar range is set up by connecting ROFS to REFIN and RFB to VOUT, and operating from dual (±5V) supplies (Figure 11). Table 5
shows the DAC-latch contents (input) vs. VOUT (output). In this range, 1 LSB = REFIN (2 -11).
Four-Quadrant Multiplication
The MAX530 can be used as a four-quadrant multiplier
by connecting ROFS to REFIN and RFB to VOUT and,
using (1) an offset binary digital code, (2) bipolar
power supplies, and (3) a bipolar analog input at
REFIN within the range VSS + 2V to VDD - 2V, as shown
in Figure 12.
In general, a 12-bit DAC’s output is (D)(V REFIN)(G),
where “G” is the gain (1 or 2) and “D” is the binary representation of the digital input divided by 212 or 4,096.
This formula is precise for unipolar operation. However,
for bipolar, offset binary operation, the MSB is really a
polarity bit. No resolution is lost, because there is the
same number of steps. The output voltage, however,
has been shifted from a range of, for example, 0V to
4.096V (G = 2) to a range of -2.048V to +2.048V.
Keep in mind that when using the DAC as a four-quadrant multiplier, the scale is skewed. The negative full
scale is -VREFIN, while the positive full scale is +VREFIN
- 1LSB.
14
Table 4. Unipolar Binary Code Table
(0V to 2VREFIN Output), Gain = 2
OV
Table 5. Bipolar (Offset Binary) Code Table
(-VREFIN to +VREFIN Output)
OUTPUT
INPUT
1111
1111
1111
(+VREFIN)
2047
2048
1000
0000
0001
(+VREFIN)
1
2048
1000
0000
0000
0111
1111
1111
(-VREFIN)
1
2048
0000
0000
0001
(-VREFIN)
2047
2048
0000
0000
0000
(-VREFIN)
2048
= -VREFIN
2048
0V
______________________________________________________________________________________
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
+5V
VDD
REFIN
REFIN
ROFS
REFOUT
MAX530
+5V
REFIN
ROFS
REFGND
33µF
MAX530
RFB
AGND
MAX530
RFB
AGND
DGND
VOUT
VOUT
DGND
VOUT
VOUT
REFGND
VSS
-5V
Figure 11. Bipolar Configuration (-2.048V to +2.048V Output)
__________Applications Information
Single-Supply Linearity
As with any amplifier, the MAX530’s output op amp offset
can be positive or negative. When the offset is positive, it
is easily accounted for. However, when the offset is negative, the output cannot follow linearly when there is no
negative supply. In that case, the amplifier output (VOUT)
remains at ground until the DAC voltage is sufficient to
overcome the offset and the output becomes positive.
The resulting transfer function is shown in Figure 13.
Normally, linearity is measured after allowing for zero
error and gain error. Since, in single-supply operation,
the actual value of a negative offset is unknown, it cannot be accounted for during test. In the MAX530, linearity and gain error are measured from code 11 to code
4095 (see Note 2 under Electrical Characteristics). The
output amplifier offset does not affect monotonicity, and
these DACs are guaranteed monotonic starting with
code zero. In dual-supply operation, linearity and gain
error are measured from code 0 to 4095.
Power-Supply Bypassing
and Ground Management
Best system performance is obtained with printed circuit boards that use separate analog and digital ground
planes. Wire-wrap boards are not recommended. The
two ground planes should be connected together at the
low-impedance power-supply source.
AGND and REFGND should be connected together,
and then to DGND at the chip. For single-supply appli-
-5V
Figure 12. Four-Quadrant Multiplying Circuit
cations, connect VSS to AGND at the chip. The best
ground connection may be achieved by connecting
the AGND, REFGND, and DGND pins together and
connecting that point to the system analog ground
plane. If DGND is connected to the system digital
ground, digital noise may get through to the DAC’s analog portion.
Bypass V DD (and V SS in dual-supply mode) with a
0.1µF ceramic capacitor connected between VDD and
AGND (and between V SS and AGND). Mount the
capacitors with short leads close to the device.
AC Considerations
Digital Feedthrough
High-speed data at any of the digital input pins may
couple through the DAC package and cause internal
stray capacitance to appear as noise at the DAC output, even though LDAC and CS are held high (see
Typical Operating Characteristics ). This digital
feedthrough is tested by holding LDAC and CS high
and toggling the data inputs from all 1s to all 0s.
Analog Feedthrough
Because of internal stray capacitance, higher-frequency analog input signals at REFIN may couple to the
output, even when the input digital code is all 0s, as
shown in the Typical Operating Characteristics graph
Analog Feedthrough vs. Frequency. It is tested by setting CLR to low (which sets the DAC latches to all 0s)
and sweeping REFIN.
______________________________________________________________________________________
15
___________________Chip Topography
D3/D11 D1/D9
POSITIVE OFFSET
OUTPUT (LSBs)
MAX530
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
4
3
2
1
0
D4
D2/D10 D0/D8
V DD
RFB
ROFS
NEGATIVE OFFSET
1
2 3
4
5
6
7
VOUT
8
D5
0.133"
(3.378mm)
DAC CODE (LSBs)
D6
V SS
D7
Figure 13. Single-Supply DAC Transfer Function
REFOUT
A0
_Ordering Information (continued)
PIN-PACKAGE
ERROR
(LSB)
MAX530AENG -40°C to +85°C
24 Narrow Plastic DIP
±1/2
MAX530BENG
MAX530AEWG
MAX530BEWG
MAX530AEAG
MAX530BEAG
24 Narrow Plastic DIP
24 Wide SO
24 Wide SO
24 SSOP
24 SSOP
±1
±1/2
±1
±1/2
±1
PART
TEMP. RANGE
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
REFGND
LDAC
A1
WR
CS
AGND
DGND
CLR
REFIN
0.087"
(2.210mm)
TRANSISTOR COUNT: 913;
SUBSTRATE CONNECTED TO VDD.
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1995 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.