Hamamatsu H7827-002 Photosensor modules consist of a 28-mm (1-1/8") diameter side-on photomultiplier tube Datasheet

Photosensor Modules
H7827 Series
The H7827 series photosensor modules incorporate a 19-mm (3/4") diameter
head-on photomultiplier tube, a high-voltage power supply circuit and a low
noise amplifier. Two types of amplifiers are available with a current-to-voltage
conversion factor of 1 V/µA or 0.1 V/µA and a frequency bandwidth of DC to
20 kHz or DC to 200 kHz. Two types of photomultiplier tubes with different
spectral response characteristics are provided for measurement in the visible
range or visible to near IR range.
Product Variations
Type No.
H7827-001
H7827-011
H7827-002
H7827-012
Spectral Response Current-to-Voltage Conversion Factor Frequency Bandwidth
300 nm to 650 nm
1 V/µA
DC to 20 kHz
300 nm to 850 nm
300 nm to 650 nm
0.1 V/µA
DC to 200 kHz
300 nm to 850 nm
Features
For general applications in visible range
For visible to near IR range
For general applications in visible range
For visible to near IR range
Specifications
Anode
Anode
Cathode
Parameter
Suffix
Input Voltage
Max. Input Voltage
Max. Input Current
Max. Control Voltage
Recommended Control Voltage Adjustment Range
Effective Area
Sensitivity Adjustment Range
Peak Sensitivity Wavelength
Min.
Luminous Sensitivity
Typ.
Blue Sensitivity Index (CS 5-58) Typ.
Red/White Ratio
Typ.
Radiant Sensitivity *1
Typ.
Suffix (with internal 20 kHz amp)
Min.
Luminous Sensitivity *2
Typ.
Radiant Sensitivity *1 *2 Typ.
Voltage Output Depending
Typ.
on PMT Dark Current *2 *3 *4 Max.
Max. Output Signal Voltage
Current-to-Voltage Conversion Factor
Suffix (with internal 200 kHz amp)
Min.
Luminous Sensitivity *2
Typ.
Radiant Sensitivity *1 *2 Typ.
Voltage Output Depending
Typ.
on PMT Dark Current *2 *3 *4 Max.
Max. Output Signal Voltage
Current-to-Voltage Conversion Factor
Offset Voltage
Typ.
Ripple Noise *2 *5 (peak to peak) Max.
Settling Time *6
Max.
Operating Ambient Temperature *7
Storage Temperature *7
Weight
H7827 Series
-001 / -002
-011 / -012
±11.5 to ±15.5
±18
+45/-1 (-001/-011), +50/-8 (-002/-012)
+1.2 (Input Impedance 100 kΩ)
+0.5 to +1.1
15
1: 103
380
420
80
60
120
90
—
10.5
0.2
—
49
85
-011
-001
1.0 × 107
1.0 × 107
3.0 × 107
5.0 × 107
13
47
3
3
20
20
+10 (Load resistance 10 kΩ)
1
-012
-002
1.0 × 106
1.0 × 106
3.0 × 106
5.0 × 106
1.3
4.7
0.3
0.3
2
2
+10 (Load resistance 10 kΩ)
0.1
H7827 series
±3
0.6
0.2
+5 to +45
-20 to +50
80
Unit
—
V
V
mA
V
V
mm
—
nm
µA/lm
—
—
mA/W
V/lm
V/nW
mV
V
V/µA
V/lm
V/nW
mV
V
V/µA
mV
mV
s
°C
°C
g
*1: Measured at the peak sensitivity wavelength
*2: Control voltage = +1.0 V
*3: After 30 minutes storage in darkness
*4: Output of anode dark current
*5: Cable RG-174/U, Cable length 450 mm, Load resistance = 1 MΩ, Load capacitance = 22 pF
*6: The time required for the output to reach a stable level following a change in the control voltage from +1.0 V to +0.5 V
*7: No condensation.
HAMAMATSU PHOTONICS K.K.
FEB. 2008
Characteristics (Anode radiant sensitivity, PMT gain)
H7827-001
-011 10
PMT GAIN: 105
TPMOB0156EA
1
H7827-002
-012
108
0.1
-001
-002
0.1
0.01
100
0.01
200
300
400
500
600
700
800
106
PMT GAIN
1
107
ANODE RADIANT SENSITIVITY (V/nW)
ANODE RADIANT SENSITIVITY (V/nW)
-011
-012
TPMOB0159EA
-001
-002
105
104
-011
-012
103
102
0.25 0.3
0.001
900
0.4
WAVELENGTH (nm)
0.5
0.7
1.0 1.2
CONTROL VOLTAGE (V)
Sensitivity Adjustment Method
VOLTAGE PROGRAMMING
RESISTANCE PROGRAMMING
POWER SUPPLY
SIGNAL OUTPUT
LOW VOLTAGE INPUT (RED)
LOW VOLTAGE INPUT (GREEN)
GND (BLACK)
Vref OUTPUT (BLUE)
Vcont INPUT (WHITE)
PHOTOSENSOR MODULE
SIGNAL OUTPUT
LOW VOLTAGE INPUT (RED)
LOW VOLTAGE INPUT (GREEN)
GND (BLACK)
Vref OUTPUT (BLUE)
Vcont INPUT (WHITE)
+15 V
-15 V
GND
+15 V
-15 V
GND
MONITOR
+0.5 V to
+1.1 V
• Adjust the control voltage to
adjust the sensitivity.
• Electrically insulate the
reference voltage output.
POWER SUPPLY
CW
PHOTOSENSOR MODULE
POTENTIOMETER (10 kΩ)
When using a potentiometer, adjust sensitivity
while monitoring the control voltage.
GND
TPMOC0166EB
Dimensional Outlines (Unit: mm)
56.0 +0.5
-0
18
THREADED
HOLE for
OPTION
(4-M2 DEPTH: 5)
10.0 ± 0.5
FRONT VIEW
SIGNAL OUTPUT
BNC-R
19.0 ± 0.5 18.0 ± 0.5
0 +0.1
-0.3
25.0 ± 0.5
14.0 ± 0.5
50.0 +1.0
-0
13.0 ± 0.5
EFFECTIVE AREA
15 MIN.
18.6 ± 0.7
26.0 +0.5
-0
16.0 ± 0.5
SIDE VIEW
POWER INPUT
HIROSE HR10A-7R-6P
1: GND
2: LOW VOLTAGE INPUT (+15 V)
3: Vcont INPUT (+0.5 V to +1.1 V)
4: Vref OUTPUT (+1.2 V)
5: NC
6: LOW VOLTAGE INPUT (-15 V)
MOUNTING THREADED HOLE
(2-M3 DEPTH: 5)
REAR VIEW
Power cable with connector (HIROSE HR10A-7P-6S) is supplied with the H7827 series
700 ± 20
BLACK:
RED:
WHITE:
BLUE:
GREEN:
GND
LOW VOLTAGE INPUT (+15 V)
Vcont INPUT (+0.5 V to +1.1 V)
Vref OUTPUT (+1.2 V)
LOW VOLTAGE INPUT (-15 V)
TPMOA0023EB
1.5
Similar pages