MD200xE Series Low Cost, 2W Miniature SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power • Miniature SIP Case • Short Circuit Protected • 1,500 VDC Isolation Input Parameter Conditions Min. 5 VDC Input 4.50 12 VDC Input 10.80 15 VDC Input 13.50 24 VDC Input 21.60 Internal Capacitor Input Voltage Range Input Filter • Single and Dual Outputs Output • >3.5 MHour MTBF Parameter Output Voltage Accuracy 3.3 VDC Output Line Regulation All Other Outputs Load Regulation, See Note 1 • -40°C to +105°C Operation • LOW COST 3.0 kV Isolation Models Available Ripple & Noise (20 MHz), See Note 2 Conditions Min. Typ. 5.0 12.0 15.0 24.0 Max. 5.50 13.20 16.50 26.40 Units Typ. ±2.5 Max. Units % ±1.5 ±1.2 For VIN Change of 1% See Model Selection Guide Output Voltage <12 VDC 60 15 VDC, 24 VDC Output 75 Temperature Coefficient Output Short Circuit VDC % mV P - P ±0.03 %/°C Typ. Max. 20 100 300 Units VDC M pF kHz Continuous (Autorecovery) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency EMI Characteristics Parameter Conditions 60 Seconds 500 VDC 100 kHz, 1V Conditions EMC Compliance, Single Output EMC Compliance, Dual Output Min. Conducted Radiated EMI Compliance, See Note 4 Min. 1,500 1,000 Electrostatic Discharge (ESD) Typ. Max. Units CISPR22/EN 55022 Level B CISPR22/EN 55022 Level B EN 61000-4-2 Level B Contact ±8 kV EN 61000-4-2 Level B Contact ±6 kV Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient Max. +105 +125 Units °C °C 95 % 0.772 x 0.276 x 0.394 Inches (19.6 x 7.0 x 10.0 mm) Non-Conductive Black Plastic (UL-94V0) 0.08 Oz (2.4g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 3.5 Typ. Max. Units MHours Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 21.0 30.0 300 Units Absolute Maximum Ratings Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature 5 VDC Input 12 VDC Input 15 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Model Number MD205S-03E MD205S-05E MD205S-12E MD205S-15E MD205S-24E MD205D-03E MD205D-05E MD205D-12E MD205D-15E MD205D-24E MD212S-03E MD212S-05E MD212S-12E MD212S-15E MD212D-03E MD212D-05E MD212D-12E MD212D-15E MD215D-15E MD224S-03E MD224S-05E MD224S-12E MD224S-15E MD224S-24E MD224D-03E MD224D-05E MD224D-12E MD224D-15E Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.5 - 5.5 476 25 5 4.5 - 5.5 450 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 540 25 5 4.5 - 5.5 500 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 208 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 196 15 12 10.8 - 13.2 198 15 15 13.5 - 16.5 157 10 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 98 8 24 21.6 - 26.4 104 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 Voltage Output Current (VDC) (mA, Max) 3.3 5.0 12.0 15.0 24.0 ±3.3 ±5.0 ±12.0 ±15.0 ±24.0 3.3 5.0 12.0 15.0 ±3.3 ±5.0 ±12.0 ±15.0 ±15.0 3.3 5.0 12.0 15.0 24.0 ±3.3 ±5.0 ±12.0 ±15.0 400 400 167 133 83 ±303 ±200 ±83 ±67 ±42 400 400 167 133 ±303 ±200 ±83 ±67 ±67 400 400 167 133 83 ±303 ±200 ±83 ±67 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external 1 µF ceramic capacitor & 10 µF electrolytic capacitor be placed in parallel from the +Vout pin to the -Vout pin for single output models, or from each output to common for dual output models. 3. Operation at no load will not damage these units, however, they may not meet all specifications. 4. These converters are specified for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. The simple connection shown below will typically meet EN 55022 Class B. For dual output units, a capacitor should be connected from each output to common. VIN C1 L1 VOUT C2 5 VDC 12 VDC 15 VDC 24 VDC 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 6.8 µH 6.8 µH 6.8 µH 6.8 µH 3.3 VDC 5 VDC 12 VDC 15 VDC 24 VDC ±3.3 VDC ±5 VDC ±12 VDC ±15 VDC ±24 VDC 10 µF 10 µF 2.2 µF 1.0 µF 1.0 µF 4.7 µF 4.7 µF 1.0 µF 0.47 µF 0.47 µF Output Load Rating Efficiency Fuse Regulation Capacitive Slow-Blow Load (%, Typ) (mA) (mA, Min) (µF Max) % Typ. 40.0 18.0 220 84 1,000 40.0 12.0 220 89 1,000 17.0 8.0 220 84 1,000 13.0 7.0 220 84 1,000 8.0 6.0 220 84 1,000 ±30.0 18.0 100 74 1,000 ±20.0 12.0 100 80 1,000 ±8.0 8.0 100 84 1,000 ±7.0 7.0 100 84 1,000 ±4.0 6.0 100 84 1,000 40.0 18.0 220 84 500 40.0 12.0 220 84 500 17.0 8.0 220 84 500 13.0 7.0 220 84 500 ±30.0 18.0 100 80 500 ±20.0 12.0 100 84 500 ±8.0 8.0 100 85 500 ±7.0 7.0 100 84 500 ±7.0 7.0 100 85 500 40.0 18.0 220 84 250 40.0 12.0 220 84 250 17.0 8.0 220 84 250 13.0 7.0 220 84 250 8.0 6.0 220 85 250 ±30.0 18.0 100 80 250 ±20.0 12.0 100 84 250 ±8.0 8.0 100 84 250 ±7.0 7.0 100 84 250 Current Derating Curve Mechanical Dimensions 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Pin Connections Pin Single Dual Pin Single Dual 1 +VIN +VIN 5 No Pin Common 6 +VOUT +VOUT 2 -VIN -VIN 4 -VOUT -VOUT MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Pin 1 is marked by a “dot” or indentation on the unit FAX: (781) 344-8481 • E-Mail: [email protected]