ETAL BMS01-2110-0 Utility vehicles for hazardous good Datasheet

Battery Master Switch BMS01
Description
The BMS01 is a battery master switch designed for dangerous goods road
vehicles complying with international ADR regulations. Environmental
protection and the intrinsically safe control circuitry of the BMS01 are
in accordance with ADR 2015. The battery switch must be installed
between the battery and the vehicle’s electrical system. It is operated
on and off by means of a control switch in the driver’s cab, additional
control switches can be sited around the vehicle as required. The
BMS01 is a double pole device, but can be connected as 1-pole
version (see connection diagram).
An integral safety barrier permits siting of the BMS01 in hazardous
areas. Additional auxiliary contacts are provided for disconnection of
the ignition circuit, de-energisation of the alternator field winding, or a
controlled shutdown of the CANBUS system followed after a delay by
disconnection of the battery.
Typical applications
Technical data
Utility vehicles for hazardous goods.
Type number
BMS01 Battery Master Switch (to ADR 2015)
Number of poles
2 2-pole
Rated voltage
0 DC 12 V
1 DC 24 V
Control function: delay time between
auxiliary contact K13 and main contacts
1 1 sec / ADR-compliant
2 9.5 sec / ADR-compliant
5 180 sec / version for SCRT (BlueTec) motors
Control function: low voltage monitoring
0
without low voltage monitoring
1
with low voltage monitoring and disconnection device switches off in undervoltage condition
3
with low voltage monitoring and signalisation
Version
0 neutral
1
1
1 - 0
ordering example
Rubber caps and mounting screws are supplied with the product.
Accessories (e.g. external control switch, 7-pole and 4-pole connectors) should be
ordered separately.
Approvals
Authority
TÜV
Standard
Rated voltage
- ADR 2015 Teil/part 9, 9.2.2 und /
and 9.7.8
- VdTÜV-Merkblatt 5205, Ausgabe /
edition 03.2015
- IEC 60079-0:2011
- IEC 60079-11:2011
- IEC 60529:2001
KBA
ECE Regelung Nr. 10 (E1) Rev. 4
DC 12 V
DC 24 V
ZELM
EN60079-0:2012+A11:2013
EN60079-11:2012
DC 12 V
DC 24 V
Protection Class
2
Operating data
Ordering information
BMS01 - 2
BMS01
Voltage rating
DC 12 V
DC 24 V
Voltage range
9...16 V
18...32 V
Rated current
200 A / pole
Max. overload current
2,400 A 1 s; 600 A 20 s
Power consumption of
electronic module
typically 5 mA (in OFF condition)
Excitation current / time of
the bistable main relay
12 V:
24 V:
typically 2.6 A / 200 ms
typically 1.3 A / 200 ms
Control circuit (EX)
ZELM 04 ATEX 0213X
Ex II (2) G [Ex ib] II C
Temperature range
-40...+70 °C (-40...+158 °F)
Reverse polarity protection
integral (in the event of reverse polarity
the master switch will disconnect
instantaneously)
Low voltage monitoring
switching thresholds:
hysteresis:
trip time:
DC 12 V
11.0 V ± 0. 3 V
typically 0.25 V
typically 60 sec
Typical life
10,000 cycles at rated current
100,000 cycles without load
Protection class: housing
Protection class: terminals
IP65
IP54 with rubber caps
Vibration
5 g (57-200 Hz), ± 0.38 mm (10-57 Hz),
test to IEC 60068-2-6, test Fc,
10 frequency cycles / axis
Shock
10 g, test to IEC 60068-2-27, test Ea
Corrosion
96 hrs 5 % salt mist, test to IEC 60068-2-11, test Ka
Humidity
240 hrs. 95 % RH,
test to IEC 60068-2-78, test Cab
Terminals
battery terminals:
control terminals:
M10 terminal studs
AUX connectors to DIN 72 585, 7-pole
CRTL connectors to DIN 72 585, 2-pole
Auxiliary contact
max. 10 A (circuit unprotected)
DC 24 V
22.8 V ± 0.3 V
typically 0.5 V
typically 60 sec
Aux. energy output for
permanently energised loads
(e.g. tachograph)
max. 1 A (internally protected)
Mass
approx. 1,700 g
IP65
1615
www.e-t-a.de
1
Battery Master Switch BMS01
Signalisation by bicoloured LED
Signalisation by bicoloured LED
red and green LED
via control switch
- Main contact closed “ON“
status LED flashes green (100 ms on; 900 ms off)
- Main contact open “OFF“
status LED flashes red (100 ms on; 900 ms off)
Low voltage detected
- Main contact closed
status LED flashes green / red (900 ms green; 100 ms red)
- Main contact open due to low voltage
status LED red permanently on
Main contact monitoring
- Main contact does not follow control switch
status LED flashes red / green (500 ms red; 500 ms green)
“error”
Dimensions
2
tightening torque max. 10 Nm
4 rubber caps (supplied with product)
max. 62
max. 2.44
200
7.87
5
mounting holes
61.6
2.42
Ø 8.8 max.
Ø .346 max.
7-pole
connector
auxiliary
to DIN 72585
BMS01
CTRL
BATT +
Ex ib
110
4.33
GERMANY
LOAD +
15
Status
Made in Germany
4-pole
connector
control
to DIN 72585
LOAD –
61.6
2.42
bicoloured
status LED
BATT –
Tmax = 10 Nm
15
.590
AUX
cylinder head screw
M5 DIN 912 / ISO 4762
tightening torque max. 3 Nm
supplied with product
.590
182
7.16
max. 99
max. 3.89
snap-on cover
max. 91
max. 3.58
female connector
(not supplied
with product)
max. 82
max. 3.23
approx. 102 (4.01) plus cable gland
M 10
M5
M 10
Notes:
1) CTRL Pin 1 has to be connected to battery minus.
2) Observe instructions for installation!.
2
This is a metric design and millimeter dimensions take precedence ( mm )
inch
www.e-t-a.de
1615
Battery Master Switch BMS01
Connection diagram 1-pole
15
tachograph
86
87
31
85
BMS01
AUX
31a
B
Ø 13
Ø .512
A
87a
Ø 21
Ø .827
Ø 16
Ø .63
D+
Terminal design
1
2
shutdown
control
K13
3
31a
4
30a
31a
5
6
signal
7
K14
- Batt
- Load
+ Batt
+ Load
A
B
30a
CTRL
1
1
2
EX-barrier
2
ADR switch
Outside
31
2
30
+
ADR switch
Inside
2
3
cable lug
Note: Ground terminal has to be connected via -Batt.
Connection diagram 2-pole
D+
15
87a
tachograph
86
87
31
85
BMS01
AUX
31a
1
2
shutdown
control
K13
3
31a
4
30a
31a
5
6
signal
7
K14
31a
- Batt
- Load
+ Batt
+ Load
30a
ADR switch
Outside
1
2
EX-barrier
IP54
2
1
CTRL
31
2
30
+
cable binder
3
ADR switch
Inside
Pin Assignment
CTRL
1 and 2 to switch the battery isolation switch ON and OFF by
means of a control switch in the driver´s cab and one
or more control switches outside the vehicle (if required)
AUX
1 and 2 current-limited supply line for permanently energised loads, e. g. tachograph, limited to 1 A
This is a metric design and millimeter dimensions take precedence ( mm )
inch
3 and 4 shutdown contact, which opens immediately after the
control switch has been operated and remains open until
the battery is disconnected
5 to de-activate low voltage disconnection when driving;
only for configuration “1” for “Control function: low
voltage monitoring”
6 and 7 signal contact, closes during the response delay and may
be used for an acoustic alarm signal during the period
until final disconnection of the battery
1615
Note: the rubber caps can be cut to match the outer diameter of the
connected cable.
Rubber caps
Outer cable dia.
(mm)
Inner dia. of rubber
caps (mm)
Cutting position
14 - 17
> 17 - 22
> 22 - 25.4
13
16
21
A-A
B-B
www.e-t-a.de
3
Battery Master Switch BMS01
Functional diagrams
Diagram 1
2
Type: BMS01-2120
switch on/off via control switch
control switch emergency
stop
ON
OFF
battery isolation switch
ON
OFF
K13 aux. contact
active
passive
K14 aux. contact
active
passive
Diagram 2
ON
OFF
battery isolation switch
ON
OFF
control input pin 5
Plus
Minus
voltage monitoring
U > 23.3 V
U < 22.8 V
K13 aux. contact
active
passive
K14 aux. contact
active
passive
ON
OFF
battery isolation switch
ON
OFF
4
tN
60 s
active
passive
control input pin 5
Plus
Minus
voltage monitoring
U > 23.3 V
U < 22.8 V
K14 aux. contact
tN
10 s
tV
9.5 s
tN
Type: BMS01-2123
with low voltage monitoring and signalisation via K14
and ON/OFF operation via control switch
control switch emergency
stop
K13 aux. contact
tN
Type: BMS01-2121
with low voltage monitoring and automatic disconnection
control switch emergency
stop
Diagram 3
tV
9.5 s
tV
9.5 s
tN
10 s
active
passive
www.e-t-a.de
1615
Battery Master Switch BMS01
Mounting holes Mounting holes:
Accessories
External Control Switch
XSB-A-...
60
2.36
Ø6
Ø .236
For more info please enquire
for a separate data sheet
182
7.16
2
1615
www.e-t-a.de
5
Battery Master Switch BMS01
Accessories
Connector sleeve (for 2- and 7-pole connectors)
4-pole connector CTRL
X 222 581 01
Y 307 978 01 (NW10)
Y 307 979 01 (d=11 mm)
Y 307 977 01 (NW10)
female connector
blanking
plug
crimp contact
seal
lock
7-pole connector AUX
X 222 580 01
2
female connector
crimp contact
seal
lock
All dimensions without tolerances are for reference only. In the interest of improved design,
performance and cost effectiveness the right to make changes in these specifications without
notice is reserved. Product markings may not be exactly as the ordering codes. Errors and
omissions excepted.
6
www.e-t-a.de
1615
Similar pages