LIGITEK LRGB9553-S6-TR1 Surface mount led tape and reel Datasheet

LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
SURFACE MOUNT LED TAPE AND REEL
Pb
Lead-Free Parts
LRGB9553/S6/TR1
DATA SHEET
DOC. NO
:
QW0905-LRGB9553/S6/TR1
REV.
:
B
DATE
: 21 - Dec. - 2007
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LRGB9553/S6/TR1
Page 1/9
Package Dimensions
3.5
3.2
3
0.7±0.05
G
1.95
2
B
2.6
0.7±0.05
2.8
R
4
0.7±0.05
1
2.2
0.7±0.05
0.6
1.95
1.05
Common Anode
4
1.Cathode Red
2.Cathode Blue
3.Cathode Green
4.Common Anode
1.5
0.9
0.9
2
1
3
B R G
Note : 1.All dimension are in millimeter tolerance is ± 0.2mm unless otherwise noted.
2.Specifications are subject to change without notice.
Carrier Type Dimensions
4.0±0.2
2.0
0.23
1.55
1.75
5.5±0.2
12.0±0.3
4.06
9.3
4.0±0.5
3.12
Note : The tolerances unless mentioned is ±0.2mm,Unit=mm.
2.24
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LRGB9553/S6/TR1
Page 2/9
Reel Dimensions
16.0±1.0
ψ178±2.0
14.2±1.0
74.0±1.5
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LRGB9553/S6/TR1
Page 3/9
Absolute Maximum Ratings at Ta=25 ℃
Ratings
Symbol
Parameter
UNIT
HRF
9UG
SBK-S
Forward Current
IF
30
30
30
mA
Peak Forward Current
Duty 1/10@10KHz
IFP
90
60
100
mA
Power Dissipation
PD
75
75
120
mW
ESD
2000
500
V
Reverse Current @5V
Ir
10
50
μA
Operating Temperature
Topr
-20 ~ +80
℃
Storage Temperature
Tstg
-30 ~ +100
℃
Electrostatic Discharge( * )
Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic
* glove
is recommended when handing these LED. All devices, equipment and machinery must be properly
grounded.
Typical Electrical & Optical Characteristics (Ta=25 ℃)
PART NO
COLOR
MATERIAL
Emitted
LRGB9553/S6-TR1
AlGaInP
Red
AlGaInP
Green
InGaN/SiC Blue
Lens
Water Clear
Forward
Luminous
Viewing
Dominant Spectral
voltage
intensity
wave
angle
halfwidth
length
△λ nm @20mA(V) @20mA(mcd) 2θ 1/2
λDnm
(deg)
Typ.
Typ.
Max.
Min.
Min.
630
20
1.5 --- 2.4
80
125
120
574
20
1.7 --- 2.6
32
50
120
475
26
--- 3.5 4.2
50
80
120
Note : 1.The forward voltage data did not including ±0.1V testing tolerance.
2. The luminous intensity data did not including ±15% testing tolerance.
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Page 4/9
PART NO. LRGB9553/S6/TR1
Typical Electro-Optical Characteristics Curve
HRF CHIP
Fig.1 Forward current vs. Forward Voltage
Fig.2 Relative Intensity vs. Forward Current
3.5
Relative Intensity
Normalize @20mA
Forward Current(mA)
1000
100
10
1.0
0.1
3.0
2.5
2.0
1.5
1.0
0.5
0
1.0
1.5
2.0
2.5
3.0
1.0
10
Fig.3 Forward Voltage vs. Temperature
Fig.4 Relative Intensity vs. Temperature
3.0
Relative Intensity@20mA
Normalize@25 ℃
1.2
Forward Voltage@20mA
Normalize @25℃
1000
Forward Current(mA)
Forward Voltage(V)
1.1
1.0
0.9
0.8
-40
-20
-0
20
40
60
80
100
2.5
2.0
1.5
1.0
0.5
0
-40
-20
0
20
40
60
80
Ambient Temperature( ℃)
Ambient Temperature( ℃)
Fig.5 Relative Intensity vs. Wavelength
Relative Intensity@20mA
100
Fig.6 Directive Radiation
0°
1.0
-30°
30 °
-60 °
0.5
0
550
600
650
Wavelength (nm)
700
100% 75% 50%
60 °
25%
0
25% 50% 75% 100%
100
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LRGB9553/S6/TR1
Page 5/9
Typical Electro-Optical Characteristics Curve
9UG CHIP
Fig.1 Forward current vs. Forward Voltage
Fig.2 Relative Intensity vs. Forward Current
3.0
Relative Intensity
Normalize @20mA
Forward Current(mA)
1000
100
10
1.0
0.1
2.5
2.0
1.5
1.0
0.5
0
1.0
2.0
3.0
4.0
5.0
1.0
10
1.2
Fig.4 Relative Intensity vs. Temperature
Relative Intensity @20mA
Normalize @25℃
Forward Voltage@20mA
Normaliz @25℃
Fig.3 Forward Voltage vs. Temperature
1.1
1.0
0.9
0.8
-20
0
20
40
60
1000
Forward Current(mA)
Forward Voltage(V)
-40
100
80
100
3.0
2.5
2.0
1.5
1.0
0.5
0
-40
-20
0
20
40
60
80
100
Ambient Temperature( ℃)
Ambient Temperature( ℃)
Fig.5 Relative Intensity vs. Wavelength
Relative Intensity @20mA
Fig.6 Directive Radiation
0°
1.0
-30°
0.5
30°
-60°
60 °
0
500
550
600
Wavelength (nm)
650
100% 75% 50%
25%
0
25% 50% 75% 100%
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LRGB9553/S6/TR1
Page 6/9
Typical Electro-Optical Characteristics Curve
SBK-S CHIP
Fig.2 Relative Intensity vs. Forward Current
30
1.5
Relative Intensity
Normalize @20mA
Forward Current(mA)
Fig.1 Forward current vs. Forward Voltage
25
20
15
10
5
0
1
2
3
4
1.25
1.0
0.75
0.5
0.25
0
5
0
5
Relative Intensity@20mA
Forward Current@20mA
40
30
20
10
0
50
75
100
Ambient Temperature( ℃)
0°
30 °
-60 °
100% 75% 50%
60 °
25%
0
25
30
1.0
0.5
0
380
430
480
530
580
Wavelength (nm)
Fig.5 Directive Radiation
-30°
20
Fig.4 Relative Intensity vs. Wavelength
Fig.3 Forward Current vs. Temperature
25
15
Forward Current(mA)
Forward Voltage(V)
0
10
25% 50% 75% 100%
630
680
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LRGB9553/S6/TR1
Page 7/9
Recommended Soldering Conditions
1. Hand Solder
Basic spec is ≦ 280℃ 3 sec one time only.
2. Wave Solder
Soldering heat Max. 260 ℃
245±5℃ within 5 sec
Preheat
120 ~ 150 ℃
120 ~ 180 sec
3. LEAD Reflow Solder
Temp.
(℃)
240
Rising
+5 ℃/sec
Cooling
-5℃/sec
Preheat
150
120
60 ~ 120 sec
Time
5sec
4. PB-Free Reflow Solder
1~5°C/sec
Preheat
180~200 °C
1~5° C/sec
260° C MaX.
10sec.Max
Above 220 °C
60 sec.Max.
120 sec.Max.
Note: 1.Wave solder and reflow soldering should not be made more than one time.
2.You can just only select one of the soldering conditions as above.
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LRGB9553/S6/TR1
Page 8/9
Precautions For Use:
Storage time:
1.The operation of Temperatures and RH are : 5 ℃~35℃,RH<60%.
2.Once the package is opened, the products should be used within a week.
Otherwise, they should be kept in a damp proof box with descanting agent.
Considering the tape life, we suggest our customers to use our products within
a year(from production date).
3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH<60%,
they should be treated at 60 ℃± 5 ℃fo r 15hrs.
Drive Method:
LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into
the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series
with the LED.
Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd
current should not be allowed to change by more than 40 % of its desired value.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit.
(B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED.
Cleaning:
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED.
ESD(Electrostatic Discharge):
Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic
glove is recommended when handing these LED. All devices, equipment and machinery must be properly
grounded.
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Page 9/9
PART NO. LRGB9553/S6/TR1
Reliability Test:
Classification
Test Item
Test Condition
Reference
Standard
Operating Life Test
1.Ta=Under Room Temperature As Per Data Sheet
Maximum Rating.
2.If=20mA
3.t=1000 hrs (-24hrs, +72hrs)
MIL-STD-750D: 1026
MIL-STD-883D: 1005
JIS C 7021: B-1
High Temperature
Storage Test
1.Ta=105 ℃±5℃
2.t=1000 hrs (-24hrs, +72hrs)
MIL-STD-883D:1008
JIS C 7021: B-10
Low Temperature
Storage Test
1.Ta=-40 ℃±5℃
2.t=1000 hrs (-24hrs, +72hrs)
JIS C 7021: B-12
High Temperature
High Humidity
Storage Test
1.IR-Reflow In-Board, 2 Times
2.Ta=65 ℃±5℃
3.RH=90 %~95%
4.t=1000hrs ±2hrs
MIL-STD-202F:103B
JIS C 7021: B-11
Endurance
Test
1.IR-Reflow In-Board,2 times
2.Ta=105 ℃±5 ℃&
-40 ℃±5 ℃
(10min) (10min)
3.total 10 cycles
MIL-STD-202F: 107D
MIL-STD-750D: 1051
MIL-STD-883D: 1011
Solder Resistance
Test
1.T.Sol=260 ℃±5℃
2.Dwell Time= 10 ±1sec.
MIL-STD-202F: 210A
MIL-STD-750D: 2031
JIS C 7021: A-1
Solderability Test
1.T.Sol=235 ℃±5℃
2.Immersion time 2 ±0.5sec
3.Immersion rate 25 ±2.5mm/sec
4.Immersion rate 25 ±2.5mm/sec
5.Coverage ≧95% of the dipped surface
MIL-STD-202F: 208D
MIL-STD-750D: 2026
MIL-STD-883D: 2003
IEC 68 Part 2-20
JIS C 7021: A-2
1.105 ℃ ~ 25 ℃ ~ 55 ℃ ~ 25℃
30mins 5mins 30mins 5mins
2.10 Cyeles
MIL-STD-202F: 107D
MIL-STD-750D: 1051
MIL-STD-883D: 1010
JIS C 7021: A-4
Ramp-up rate(183 ℃ to Peak) +3 ℃ second max
Temp. maintain at 125( ±25) ℃ 120 seconds max
Temp. maintain above 183 ℃ 60-150 seconds
Peak temperature range 235 ℃+5-0 ℃
Time within 5 ℃ of actual Peak Temperature(tp)
10-30 seconds
Ramp-down rate +6 ℃/second max
MIL-STD-750D:2031.2
J-STD-020
Thermal Shock Test
Environmental
Test
Temperature
Cycling
Solderability Test
Similar pages