AIMTEC AM10CW-2405S-NZ 10 watt | dc-dc converter Datasheet

Series AM10CW-NZ
10 Watt | DC-DC Converter
Picture coming soon
FEATURES:










Wide 4:1 Input Voltage Range
High efficiency up to 88%
1500 VDC Isolation
Over Current Protection
No load consumption ≤ 0.12W
Operating Temperature -40ºC to +85ºC
Output Over Voltage protection
Continuous Short Circuit Protection
Input Under voltage Protection
Remote On/Off control
Models
Single output
Model
Input
Voltage (V)
Output
Voltage
(V)
Output
Current max
(A)
Isolation
(VDC)
Max
Capacitive
Load (uF)
Efficiency
(%)
AM10CW-2403S-NZ
AM10CW-2405S-NZ
AM10CW-2409S-NZ
AM10CW-2412S-NZ
AM10CW-2415S-NZ
AM10CW-2424S-NZ
AM10CW-4803S-NZ
AM10CW-4805S-NZ
AM10CW-4812S-NZ
AM10CW-4815S-NZ
AM10CW-4824S-NZ
9-36
9-36
9-36
9-36
9-36
9-36
18-75
18-75
18-75
18-75
18-75
3.3
5
9
12
15
24
3.3
5
12
15
24
2.4
2
1.11
0.83
0.66
0.41
2.4
2
0.83
0.66
0.41
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
2200
2200
680
470
330
100
2200
2200
470
330
100
79
83
86
87
87
88
79
83
87
87
88
Input
Voltage (V)
Output
Voltage
(V)
Output
Current max
(A)
Isolation
(VDC)
Max
Capacitive
Load (uF)
Efficiency
(%)
Models
Dual output
Model
AM10CW-2405D-NZ
9-36
±5
±1
1500
±1000
83
AM10CW-2412D-NZ
9-36
±12
±0.41
1500
±470
87
AM10CW-2415D-NZ
9-36
±15
±0.33
1500
±330
87
AM10CW-2424D-NZ
9-36
±24
±0.2
1500
±100
87
AM10CW-4805D-NZ
18-75
±5
±1
1500
±1000
83
AM10CW-4812D-NZ
18-75
±12
±0.41
1500
±470
87
AM10CW-4815D-NZ
18-75
±15
±0.33
1500
±330
87
AM10CW-4824D-NZ
18-75
±24
±0.2
1500
±100
87
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Voltage range
Nominal
Typical
24 Vin
48 Vin
9-36
18-75
Filter
Absolute Maximum Rating (100ms)
No Load Input Current
Input reflected current
Input Under voltage turn off
Startup time
Remote On/Off Control
www.aimtec.com
F 051e R13
Maximum
Units
VDC
Pi
24 Vin
48 Vin
24 Vin
48 Vin
24 Vin
48 Vin
24 Vin
48 Vin
Nominal input, resistive load
On
Off
-0.7 - 50
-0.7 - 100
12
8
40
30
6.5
15.5
10
mA
mA
VDC
ms
3.5-12VDC or leave open
0-1.2VDC or connect to GND, idle current 6-10mA
Tel: +1 514 620 2722
1 of 3
VDC
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM10CW-NZ
10 Watt | DC-DC Converter
Isolation Specifications
Parameters
Tested I/O voltage
Resistance
Capacitance
Conditions
Typical
60 sec, <1mA
500VDC
I/O, 100KHz/0.1V
1500
Maximum
Units
>1000
VDC
MOhm
pF
1000
Output Specifications
Parameters
Voltage accuracy
Voltage balance (Dual Output Models)
Over voltage protection
Over current protection
Short Circuit protection
Short circuit restart
Line voltage regulation (Single)
Line voltage regulation (Dual)
Load voltage regulation (Single)
Load voltage regulation (Dual)
Cross Regulation (Dual Output Models)
Temperature coefficient
Ripple & Noise
Transient recovery time
Transient recovery deviation
Conditions
Typical
Maximum
Units
5% to 100% load
Balanced Load
±2
±3
±1.5
%
%
% of Vout
% of Iout
±0.5
±1
±1
±1.5
% of Vin
% of Vin
%
%
110-160
110-190
Continuous
Auto-Recovery
Full load, LL to HL
Full load, LL to HL
5% to 100% load
5% to 100% load
50% load on one output & 10-100%
load on second load
100% load
20MHz Bandwidth, 5-100% load
25% load step change
25% load step change
±5
%
±0.03
80
500
±5
%/oC
mV p-p
µs
%
General Specifications
Parameters
Conditions
Typical
Switching frequency
Operating temperature
Storage temperature
Maximum case temperature
Cooling
Humidity
Case material
Weight
Dimensions (L x W x H)
MTBF
Maximum soldering temperature
100% load
See derating curve
350
Maximum
Units
100
KHz
oC
oC
oC
-40 to +85
-55 to +125
Free air convection
95
Aluminum Alloy
15
1 x 1 x 0.46 inches
25.40 x 25.40 x 11.70 mm
o
>1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C)
1.5mm from case for 10 sec
300
% RH
g
oC
Environmental Specifications
Parameters
Vibration
Test mode
Acceleration
10-55Hz
10G, 30min one cycle, every axis tested
Safety Specifications
Parameters
Approval
Standards
www.aimtec.com
F 051e R13
CE, UL, pending
EN 55022, class B (with the recommended EMC circuit)
Electrostatic Discharge Immunity
IEC 61000-4-2, Contact ±4KV, Criteria B
RF, Electromagnetic Field Immunity
IEC 61000-4-3, 10V/m, Criteria A
Electrical Fast Transient / Burst Immunity
IEC 61000-4-4, ±2KV, Criteria B (with the recommended EMC circuit)
Surge Immunity
IEC 61000-4-5, ±2KV, Criteria B (with the recommended EMC circuit)
RF, Conducted Disturbance Immunity
IEC 61000-4-6, 3 Vrms, Criteria A
Voltage dips, Short Interruptions & Voltage
IEC 61000-4-29: 0-70%, Criteria B
variations Immunity
Tel: +1 514 620 2722
2 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM10CW-NZ
10 Watt | DC-DC Converter
Pin Out Specifications
Bottom View
2.54
(0.10)
Top View
25.40
(1.00)
10.16 2.54
(0.40) (0.10)
10.16
(0.40)
5
4
+V Output
20.32
(0.80)
1
2
3
4
5
6
Dimensions
Dual
+V Input
-V Input
On/Off Control
+V Output
Common
-V Output
25.40
(1.00)
Single
+V Input
-V Input
On/Off Control
+V Output
No pin
-V Output
Pin
+V
Input
Derating
1
6
-V Output
-V
Input CTRL
2
3
65 ºC 3.3, 5V & ±5V models
Side View
71ºC Other models
80
10.16
(0.40)
5.08 7.62
(0.20) (0.30)
Printed Face
11.70
(0.46)
60
Safe Operating Area
40
2.54
(0.10)
ᴓ 1.00
(0.39)
4.10
(0.16)
Output Power (%)
100
2.54
(0.10)
Free Air Convection
20
0
- 20
- 40
0
20
40
65 71
60
Dimensions mm (inch)
Case Tolerance ±0.50 (±0.02)
Pin Diameter 1.0 ± 0.10 (0.04 ± 0.004)
80 85 100
Ambient Temperature º C
Recommended EMC Circuits
CY1
1nF/2KV
LDM
4.7µH
F1
+Vin
C1
MOV
+Vo
C3
C2
DC‐DC Converter
‐Vo
‐Vin
CY2
1nF/2KV
MOV
C1
C2
C3
24V input
S14K35
330µF/50V
1µF/50V
10µF/50V
48V input
S14K60
330µF/100V
1µF/100V
10µF/100V
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R13
Tel: +1 514 620 2722
3 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Similar pages