AZ767 SPDT SUBMINIATURE POWER RELAY FEATURES • • • • Low cost 10 Amp switching Epoxy sealed version available UL, CUR file E44211 CONTACTS GENERAL DATA Arrangement SPST (1 Form A) SPDT (1 Form C) Ratings Resistive Load: SPST-NO Standard coil Sensitive coil SPDT Max. Max. Max. Max. switched switched switched switched power: 150 W or 1250 VA current: 5 ADC or 10 AAC power: 90 W or 750 VA current: 3 A Max. switched power: 90 W or 750 VA Max. switched current: 3 A Max. switched voltage: 150 VDC* or 380 VAC * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory Rated Load UL, CUR Standard coil Sensitive coil Form A 10 A at 125 VAC, Res., 30k cycles 5 A at 30 VDC / 250 VAC, 100k cycles 10 A LRA / 1.5 A FLA at 120 VAC, 100k cycles 1/ 10 HP at 125 VAC, 100k cycles 1/ HP at 250 VAC, 100k cycles 6 5 A at 125 VAC, Res., 100k cycles 3 A at 30 VDC / 250 VAC, 100k cycles Form C 3 A at 30 VDC / 250 VAC, 100k cycles Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 5 A 250 VAC Res. Operate Time (typical) 8 ms at nominal coil voltage Release Time (typical) 5 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 2500 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH Dropout Greater than 5% of nominal coil voltage Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 70°C (158°F) standard -40°C (-40°F) to 85°C (185°F) sensitive -40°C (-40°F) to 105°C (221°F) Storage Vibration 0.062" (1.5 mm) DA at 10–50 Hz Shock 10 g operating, 100 g damage Enclosure P.B.T. polyester Terminals Tinned copper alloy, P. C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Material Silver cadmium oxide Max. Solvent Temp. 80°C (176°F) Resistance < 100 milliohms initially Max. Immersion Time 30 seconds Weight 6 grams Packing unit in pcs 50 per plastic tray / 500 per carton box COIL Power At Pickup Voltage (typical) 253 mW standard coil 113 mW sensitive coil NOTES Max. Continuous Dissipation 1.25 W at 20°C (68°F) ambient Temperature Rise (at nominal voltage) 41°C (74°F) standard coil 22°C (40°F) sensitive coil 1. All values at 20°C (68°F). Max. 130°C (266°F) 3. Specifications subject to change without notice. Temperature ZETTLER 2. Relay may pull in with less than “Must Operate” value. electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2005-03-08 AZ767 RELAY ORDERING DATA STANDARD RELAYS COIL SPECIFICATIONS Nominal Coil VDC 3 ORDER NUMBER* Must Operate VDC 2.25 Max. Continuous VDC 5.0 Coil Resistance Ohm ± 10% 20 Form A (SPST) Form C (SPDT) AZ767–1A–3D AZ767–1C–3D 5 3.75 8.3 55 AZ767–1A–5D AZ767–1C–5D 6 4.5 10.0 80 AZ767–1A–6D AZ767–1C–6D 9 6.75 15.0 180 AZ767–1A–9D AZ767–1C–9D 12 9.0 20.0 320 AZ767–1A–12D AZ767–1C–12D 18 13.5 30.0 720 AZ767–1A–18D AZ767–1C–18D 24 18.0 40.0 1,280 AZ767–1A–24D AZ767–1C–24D SENSITIVE RELAYS COIL SPECIFICATIONS Nominal Coil VDC 3 ORDER NUMBER* Must Operate VDC 2.25 Max. Continuous VDC 7.5 Coil Resistance Ohm ± 10% 45 Form A (SPST) 5 3.75 12.5 125 AZ767–1A–5DS 6 4.5 15.0 180 AZ767–1A–6DS AZ767–1A–3DS 9 6.75 22.4 400 AZ767–1A–9DS 12 9.0 30.0 720 AZ767–1A–12DS 18 13.5 44.7 1,600 AZ767–1A–18DS 24 18.0 59.2 2,800 AZ767–1A–24DS * Add suffix “E” for epoxy sealed version. MECHANICAL DATA PC BOARD LAYOUT .059 [1.50] .073 [1.85] .100 [2.54] .058 [1.49] .417 MAX. [10.59] .740 MAX. [18.80] .300 [7.62] 5 x ø .052 [ø1.3] .441 [11.20] FORM C ONLY Viewed toward terminals WIRING DIAGRAMS .614 MAX. [15.59] Form A Form C .147 [3.73] .073 [1.85] Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2005-03-08