February 2005 AS7C331MPFD32A AS7C331MPFD36A ® 3.3V 1M × 32/36 pipelined burst synchronous SRAM Features • • • • • • • • • • • • • • • Organization: 1,048,576 words × 32 or 36 bits Fast clock speeds to 200 MHz Fast clock to data access: 3.1/3.5/3.8 ns Fast OE access time: 3.1/3.5/3.8 ns Fully synchronous register-to-register operation Double-cycle deselect Asynchronous output enable control Available in 100-pin TQFP package Individual byte write and global write Multiple chip enables for easy expansion 3.3V core power supply 2.5V or 3.3V I/O operation with separate VDDQ Linear or interleaved burst control Snooze mode for reduced power-standby Common data inputs and data outputs Logic block diagram LBO CLK ADV ADSC ADSP CLK CE CLR A[19:0] D Q CE Address register CLK 20 GWE BWE BWd 2 20 18 D DQd Q Byte write registers CLK 1M × 32/36 Memory array 2 20 32/36 32/36 D DQ Q c Byte write registers CLK BWc D DQb Q Byte write registers CLK BWb D DQa Q Byte write registers CLK BWa CE0 CE1 CE2 ZZ Q0 Burst logic Q1 D Q Enable CE register CLK Power down 4 OE Output registers CLK Input registers CLK D Enable Q delay register CLK 32/36 OE DQ[a:d] Selection guide Minimum cycle time Maximum clock frequency Maximum clock access time Maximum operating current Maximum standby current Maximum CMOS standby current (DC) 2/10/05, v.1.1 -200 5 200 3.1 450 170 90 Alliance Semiconductor -166 6 166 3.5 400 150 90 -133 7.5 133 3.8 350 140 90 Units ns MHz ns mA mA mA 1 of 19 Copyright © Alliance Semiconductor. All rights reserved. AS7C331MPFD32A AS7C331MPFD36A ® 32 Mb Synchronous SRAM products list1,2 Org 2MX18 1MX32 1MX36 2MX18 1MX32 1MX36 2MX18 1MX32 1MX36 2MX18 Part Number AS7C332MPFS18A AS7C331MPFS32A AS7C331MPFS36A AS7C332MPFD18A AS7C331MPFD32A AS7C331MPFD36A AS7C332MFT18A AS7C331MFT32A AS7C331MFT36A AS7C332MNTD18A Mode PL-SCD PL-SCD PL-SCD PL-DCD PL-DCD PL-DCD FT FT FT NTD-PL Speed 200/166/133 MHz 200/166/133 MHz 200/166/133 MHz 200/166/133 MHz 200/166/133 MHz 200/166/133 MHz 7.5/8.5/10 ns 7.5/8.5/10 ns 7.5/8.5/10 ns 200/166/133 MHz 1MX32 1MX36 2MX18 1MX32 1MX36 AS7C331MNTD32A AS7C331MNTD36A AS7C332MNTF18A AS7C331MNTF32A AS7C331MNTF36A NTD-PL NTD-PL NTD-FT NTD-FT NTD-FT 200/166/133 MHz 200/166/133 MHz 7.5/8.5/10 ns 7.5/8.5/10 ns 7.5/8.5/10 ns 1 Core Power Supply: VDD = 3.3V + 0.165V 2 I/O Supply Voltage: VDDQ = 3.3V + 0.165V for 3.3V I/O VDDQ = 2.5V + 0.125V for 2.5V I/O PL-SCD PL-DCD FT NTD1-PL NTD-FT : : : : : Pipelined Burst Synchronous SRAM - Single Cycle Deselect Pipelined Burst Synchronous SRAM - Double Cycle Deselect Flow-through Burst Synchronous SRAM Pipelined Burst Synchronous SRAM with NTDTM Flow-through Burst Synchronous SRAM with NTDTM 1NTD: No Turnaround Delay. NTDTM is a trademark of Alliance Semiconductor Corporation. All trademarks mentioned in this document are the property of their respective owners. 2/10/05, v.1.1 Alliance Semiconductor 2 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Pin assignment 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 TQFP 14 x 20mm 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DQPb/NC DQb7 DQb6 VDDQ VSSQ DQb5 DQb4 DQb3 DQb2 VSSQ VDDQ DQb1 DQb0 VSS NC VDD ZZ DQa7 DQa6 VDDQ VSSQ DQa5 DQa4 DQa3 DQa2 VSSQ VDDQ DQa1 DQa0 DQPa/NC LBO A A A A A1 A0 NC A VSS VDD A A A A A A A A A 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 NC/DQPc DQc0 DQc1 VDDQ VSSQ DQc2 DQc3 DQc4 DQc5 VSSQ VDDQ DQc6 DQc7 NC VDD NC VSS DQd0 DQd1 VDDQ VSSQ DQd2 DQd3 DQd4 DQd5 VSSQ VDDQ DQd6 DQd7 NC/DQPd 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A CE0 CE1 BWd BWc BWb BWa CE2 VDD VSS CLK GWE BWE OE ADSC ADSP ADV A A 100-pin TQFP - top view Note: For pins 1, 30, 51, and 80, NC applies to the x32 configuration. DQPn applies to the x36 configuration. 2/10/05, v.1.1 Alliance Semiconductor 3 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Functional description The AS7C331MPFD32A/36A is a high-performance CMOS 32-Mbit Synchronous Static Random Access Memory (SRAM) device organized as 1,048,576 words x 32/36. It incorporates a two-stage register-register pipeline for highest frequency on any given technology. Fast cycle times of 5/6/7.5 ns with clock access times (tCD) of 3.1/3.5/3.8 ns enable 200,166and 133MHz bus frequencies. Three chip enable (CE) inputs permit easy memory expansion. Burst operation is initiated in one of two ways: the controller address strobe (ADSC), or the processor address strobe (ADSP). The burst advance pin (ADV) allows subsequent internally generated burst addresses. Read cycles are initiated with ADSP (regardless of WE and ADSC) using the new external address clocked into the on-chip address register when ADSP is sampled low, the chip enables are sampled active, and the output buffer is enabled with OE. In a read operation, the data accessed by the current address registered in the address registers by the positive edge of CLK are carried to the data-out registers and driven on the output pins on the next positive edge of CLK. ADV is ignored on the clock edge that samples ADSP asserted, but is sampled on all subsequent clock edges. Address is incremented internally for the next access of the burst when ADV is sampled low and both address strobes are high. Burst mode is selectable with the LBO input. With LBO unconnected or driven high, burst operations use an interleaved count sequence. With LBO driven low, the device uses a linear count sequence. Write cycles are performed by disabling the output buffers with OE and asserting a write command. A global write enable GWE writes all 32/36 bits regardless of the state of individual BW[a:d] inputs. Alternately, when GWE is high, one or more bytes may be written by asserting BWE and the appropriate individual byte BWn signals. BWn is ignored on the clock edge that samples ADSP low, but it is sampled on all subsequent clock edges. Output buffers are disabled when BWn is sampled LOW regardless of OE. Data is clocked into the data input register when BWn is sampled low. Address is incremented internally to the next burst address if BWn and ADV are sampled low. This device operates in doublecycle deselect feature during read cycles. Read or write cycles may also be initiated with ADSC instead of ADSP. The differences between cycles initiated with ADSC and ADSP follow. ADSP must be sampled high when ADSC is sampled low to initiate a cycle with ADSC. WE signals are sampled on the clock edge that samples ADSC low (and ADSP high). Master chip enable CE0 blocks ADSP, but not ADSC. The AS7C331MPFD32A/36A family operates from a core 3.3V power supply. I/Os use a separate power supply that can operate at 2.5V or 3.3V. These devices are available in a 100-pin TQFP package. TQFP capacitance Parameter Input capacitance I/O capacitance Symbol CIN* CI/O* Test conditions VIN = 0V VOUT = 0V Min - Max 5 7 Unit pF pF * Guaranteed not tested TQFP thermal resistance Description Thermal resistance (junction to ambient)1 Thermal resistance (junction to top of case)1 Conditions Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA/JESD51 1–layer Symbol θJA Typical Units 4–layer θJA 40 22 °C/W °C/W θJC 8 °C/W 1 This parameter is sampled 2/10/05, v.1.1 Alliance Semiconductor 4 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Signal descriptions Pin CLK A,A0,A1 DQ[a,b,c,d] I/O I I I/O Properties CLOCK SYNC SYNC CE0 I SYNC CE1, CE2 I SYNC ADSP ADSC ADV I I I SYNC SYNC SYNC GWE I SYNC BWE I SYNC BW[a,b,c,d] I SYNC OE I ASYNC LBO I STATIC ZZ NC I - ASYNC - Description Clock. All inputs except OE, ZZ, and LBO are synchronous to this clock. Address. Sampled when all chip enables are active and when ADSC or ADSP are asserted. Data. Driven as output when the chip is enabled and when OE is active. Master chip enable. Sampled on clock edges when ADSP or ADSC is active. When CE0 is inactive, ADSP is blocked. Refer to the “Synchronous truth table” for more information. Synchronous chip enables, active high, and active low, respectively. Sampled on clock edges when ADSC is active or when CE0 and ADSP are active. Address strobe processor. Asserted low to load a new address or to enter standby mode. Address strobe controller. Asserted low to load a new address or to enter standby mode. Advance. Asserted low to continue burst read/write. Global write enable. Asserted low to write all 32/36 and 18 bits. When high, BWE and BW[a:d] control write enable. Byte write enable. Asserted low with GWE high to enable effect of BW[a:d] inputs. Write enables. Used to control write of individual bytes when GWE is high and BWE is low. If any of BW[a:d] is active with GWE high and BWE low, the cycle is a write cycle. If all BW[a:d] are inactive, the cycle is a read cycle. Asynchronous output enable. I/O pins are driven when OE is active and chip is in read mode. Selects Burst mode. When tied to VDD or left floating, device follows interleaved Burst order. When driven Low, device follows linear Burst order. This signal is internally pulled High. Snooze. Places device in low power mode; data is retained. Connect to GND if unused. No connect Snooze Mode SNOOZE MODE is a low current, power-down mode in which the device is deselected and current is reduced to ISB2. The duration of SNOOZE MODE is dictated by the length of time the ZZ is in a High state. The ZZ pin is an asynchronous, active high input that causes the device to enter SNOOZE MODE. When the ZZ pin becomes a logic High, ISB2 is guaranteed after the time tZZI is met. After entering SNOOZE MODE, all inputs except ZZ is disabled and all outputs go to High-Z. Any operation pending when entering SNOOZE MODE is not guaranteed to successfully complete. Therefore, SNOOZE MODE (READ or WRITE) must not be initiated until valid pending operations are completed. Similarly, when exiting SNOOZE MODE during tPUS, only a DESELECT or READ cycle should be given while the SRAM is transitioning out of SNOOZE MODE. 2/10/05, v.1.1 Alliance Semiconductor 5 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Write enable truth table (per byte) Function Write All Bytes Write Byte a Write Byte c and d Read GWE L H H H H H BWE X L L L H L BWa X L L H X H BWb X L H H X H BWc X L H L X H BWd X L H L X H Key: X = don’t care, L = low, H = high, n = a, b, c, d; BWE, BWn = internal write signal. Asynchronous Truth Table Operation Snooze mode Read Write Deselected ZZ H L L L L OE X L H X X I/O Status High-Z Dout High-Z Din, High-Z High-Z Notes: 1. X means “Don’t Care” 2. ZZ pin is pulled down internally 3. For write cycles that follows read cycles, the output buffers must be disabled with OE, otherwise data bus contention will occur. 4. Snooze mode means power down state of which stand-by current does not depend on cycle times 5. Deselected means power down state of which stand-by current depends on cycle times Burst sequence table Interleaved burst address (LBO = 1) A1 A0 A1 A0 A1 A0 Starting Address First Increment Second Increment Third Increment 2/10/05, v.1.1 00 01 10 11 01 00 11 10 10 11 00 01 Linear burst address (LBO = 0) A1 A0 A1 A0 A1 A0 A1 A0 11 10 01 00 Starting Address First Increment Second Increment Third Increment Alliance Semiconductor 00 01 10 11 01 10 11 10 10 11 00 01 A1 A0 11 00 01 10 6 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Synchronous truth table CE01 CE1 CE2 ADSP ADSC H L L L L L L L L X X X X H H H H L X H X H X L L X X H H H H X X X X X X X X H X X X X X X X H H L L L L X X X X X X X X L X X X X X L H L H L L H H H H H H X X X X H H X H X L X L X L X X L L H H H H H H H H L H H H H ADV WRITE X X X X X X X X X L L H H L L H H X L L H H X X X X X X X H H H H H H H H H H L L L L L OE Address accessed CLK Operation DQ X X X X X L H L H L H L H L H L H X X X X X NA NA NA NA NA External External External External Next Next Current Current Next Next Current Current External Next Next Current Current L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H L to H Deselect Deselect Deselect Deselect Deselect Begin read Begin read Begin read Begin read Continue read Continue read Suspend read Suspend read Continue read Continue read Suspend read Suspend read Begin write Continue write Continue write Suspend write Suspend write Hi−Z Hi−Z Hi−Z Hi−Z Hi−Z Q Hi−Z Q Hi−Z Q Hi−Z Q Hi−Z Q Hi−Z Q Hi−Z D3 D D D D 1 X = don’t care, L = low, H = high 2 For WRITE, L means any one or more byte write enable signals (BWa, BWb, BWc or BWd) and BWE are LOW or GWE is LOW. WRITE = HIGH for all BWx, BWE, GWE HIGH. See "Write enable truth table (per byte)," on page 6 for more information. 3 For write operation following a READ, OE must be high before the input data set up time and held high throughout the input hold time. 4. ZZ pin is always Low. 2/10/05, v.1.1 Alliance Semiconductor 7 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Absolute maximum ratings Parameter Power supply voltage relative to GND Input voltage relative to GND (input pins) Symbol VDD, VDDQ VIN Min –0.5 –0.5 Max +4.6 VDD + 0.5 Unit V V VIN Pd IOUT Tstg Tbias –0.5 – – –65 –65 VDDQ + 0.5 1.8 20 +150 +135 V W mA o C o C Input voltage relative to GND (I/O pins) Power dissipation Short circuit output current Storage temperature Temperature under bias Stresses greater than those listed under “Absolute maximum ratings” may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect reliability. Recommended operating conditions at 3.3V I/O Parameter Supply voltage for inputs Supply voltage for I/O Ground supply Symbol VDD VDDQ Vss Min 3.135 3.135 0 Nominal 3.3 3.3 0 Max 3.465 3.465 0 Unit V V V Min 3.135 2.375 0 Nominal 3.3 2.5 0 Max 3.465 2.625 0 Unit V V V Recommended operating conditions at 2.5V I/O Parameter Supply voltage for inputs Supply voltage for I/O Ground supply 2/10/05, v.1.1 Symbol VDD VDDQ Vss Alliance Semiconductor 8 of 19 AS7C331MPFD32A AS7C331MPFD36A ® DC electrical characteristics for 3.3V I/O operation Parameter Input leakage current† Output leakage current Sym |ILI| |ILO| Input high (logic 1) voltage VIH Input low (logic 0) voltage VIL Output high voltage Output low voltage VOH VOL Conditions VDD = Max, 0V < VIN < VDD OE ≥ VIH, VDD = Max, 0V < VOUT < VDDQ Address and control pins I/O pins Address and control pins I/O pins IOH = –4 mA, VDDQ = 3.135V IOL = 8 mA, VDDQ = 3.465V Min -2 -2 Max 2 2 Unit µA µA 2* 2* -0.3** -0.5** 2.4 – VDD+0.3 VDDQ+0.3 0.8 0.8 – 0.4 V V V V DC electrical characteristics for 2.5V I/O operation Parameter Input leakage current† Output leakage current Sym |ILI| |ILO| Input high (logic 1) voltage VIH Input low (logic 0) voltage VIL Output high voltage Output low voltage VOH VOL Conditions VDD = Max, 0V < VIN < VDD OE ≥ VIH, VDD = Max, 0V < VOUT < VDDQ Address and control pins I/O pins Address and control pins I/O pins IOH = –4 mA, VDDQ = 2.375V IOL = 8 mA, VDDQ = 2.625V Min -2 -2 1.7* 1.7* -0.3** -0.3** 1.7 – Max 2 2 VDD+0.3 VDDQ+0.3 0.7 0.7 – 0.7 Unit µA µA V V V V V V † LBO and ZZ pins have an internal pull-up or pull-down, and input leakage = ±10 µA. *V max < VDD +1.5V for pulse width less than 0.2 X t IH CYC ** VIL min = -1.5 for pulse width less than 0.2 X tCYC IDD operating conditions and maximum limits Parameter Operating power supply current1 Sym ICC ISB Standby power supply current Conditions CE0 < VIL, CE1 > VIH, CE2 < VIL, f = fMax, IOUT = 0 mA, ZZ < VIL All VIN ≤ 0.2V or > VDD – 0.2V, Deselected, f = fMax, ZZ < VIL -200 -166 -133 450 400 350 170 150 140 ISB1 Deselected, f = 0, ZZ < 0.2V, all VIN ≤ 0.2V or ≥ VDD – 0.2V 90 90 90 ISB2 Deselected, f = fMax, ZZ ≥ VDD – 0.2V, all VIN ≤ VIL or ≥ VIH 80 80 80 Unit mA mA 1 ICC given with no output loading. ICC increases with faster cycle times and greater output loading. 2/10/05, v.1.1 Alliance Semiconductor 9 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Timing characteristics over operating range Parameter Sym fMax tCYC tCD tOE tLZC tOH tLZOE tHZOE tHZC tOHOE tCH tCL tAS tDS tWS tCSS tAH tDH tWH tCSH tADVS tADSPS tADSCS tADVH tADSPH tADSCH Clock frequency Cycle time Clock access time Output enable low to data valid Clock high to output low Z Data output invalid from clock high Output enable low to output low Z Output enable high to output high Z Clock high to output high Z Output enable high to invalid output Clock high pulse width Clock low pulse width Address setup to clock high Data setup to clock high Write setup to clock high Chip select setup to clock high Address hold from clock high Data hold from clock high Write hold from clock high Chip select hold from clock high ADV setup to clock high ADSP setup to clock high ADSC setup to clock high ADV hold from clock high ADSP hold from clock high ADSC hold from clock high –200 Min Max – 200 5 – – 3.1 – 3.1 0 – 1.5 – 0 – – 3.0 – 3.0 0 – 2.0 – 2.0 – 1.4 – 1.4 – 1.4 – 1.4 – 0.4 – 0.4 – 0.4 – 0.4 – 1.4 – 1.4 – 1.4 – 0.4 – 0.4 – 0.4 – –166 Min Max – 166 6 – – 3.5 – 3.5 0 – 1.5 – 0 – – 3.4 – 3.4 0 – 2.4 – 2.4 – 1.5 – 1.5 – 1.5 – 1.5 – 0.5 – 0.5 – 0.5 – 0.5 – 1.5 – 1.5 – 1.5 – 0.5 – 0.5 – 0.5 – -133 Min – 7.5 – – 0 1.5 0 – – 0 2.4 2.4 1.5 1.5 1.5 1.5 0.5 0.5 0.5 0.5 1.5 1.5 1.5 0.5 0.5 0.5 Max 133 – 3.8 3.8 – – – 3.8 3.8 – – – – – – – – – – – – – – – – – Unit MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Notes1 2,3,4 2 2,3,4 2,3,4 2,3,4 5 5 6 6 6,7 6,8 6 6 6,7 6,8 6 6 6 6 6 6 1 See “Notes” on page 16. Snooze Mode Electrical Characteristics Description Current during Snooze Mode ZZ active to input ignored ZZ inactive to input sampled ZZ active to SNOOZE current ZZ inactive to exit SNOOZE current 2/10/05, v.1.1 Conditions Symbol ZZ > VIH ISB2 tPDS tPUS tZZI tRZZI Alliance Semiconductor Min Max Units 80 mA cycle cycle cycle 2 2 2 0 10 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Key to switching waveforms Rising input Falling input don’t care Undefined Timing waveform of read cycle tCYC tCL tCH CLK tADSPS tADSPH ADSP tADSCS tADSCH ADSC LOAD NEW ADDRESS tAH tAS A1 Address A2 tWS A3 tWH GWE, BWE tCSS tCSH CE0, CE2 CE1 tADVS tADVH ADV ADV inserts wait states OE tOE tHZOE tLZOE Dout Q(A1) Read Q(A1) Suspend Read Q(A1) Read Q(A2) tCD tHZC tOH Q(A2) Q(A2Ý01) Q(A2Ý10) Q(A2Ý11) Q(A3) Q(A3Ý01) Q(A3Ý10) Burst Burst Read Suspend Burst Burst Burst Burst Read Read Q(A3) DSEL* Read Read Read Read Read Q(A 2Ý01) Q(A 2Ý10) Q(A 2Ý10) Q(A 2Ý11) Q(A 3Ý01) Q(A 3Ý10) Q(A 3Ý11) Note: Ý = XOR when LBO = high/no connect; Ý = ADD when LBO = low. BW[a:d] is don’t care. *Outputs are disabled within two clk cycles after DSEL command 2/10/05, v.1.1 Alliance Semiconductor 11 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Timing waveform of write cycle tCYC tCL tCH CLK tADSPS tADSPH ADSP tADSCS tADSCH ADSC ADSC LOADS NEW ADDRESS tAS tAH A1 Address A3 A2 tWS tWH tADVS tADVH tDS tDH BWE BW[a:d] tCSS tCSH CE0, CE2 CE1 ADV SUSPENDS BURST ADV OE Din D(A1) Read Q(A1) Suspend Write D(A1) D(A2) Read Q(A2) D(A2Ý01) Suspend Write D(A 2) D(A2Ý01) D(A2Ý10) D(A2Ý11) D(A3) ADV ADV ADV Suspend Burst Burst Burst Write Write Write D(A 2Ý01) Write D(A 2Ý01) D(A 2Ý10) D(A 2Ý11) D(A3Ý01) Write D(A 3) D(A3Ý10) Burst Write D(A 3Ý01) ADV Burst Write D(A 3Ý10) Note: Ý = XOR when LBO = high/no connect; Ý = ADD when LBO = low. 2/10/05, v.1.1 Alliance Semiconductor 12 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Timing waveform of read/write cycle (ADSP Controlled; ADSC High) tCYC tCL tCH CLK tADSPH tADSPS ADSP tAH tAS A2 A1 Address A3 tWH tWS GWE CE0, CE2 CE1 tADVH tADVS ADV OE tDS tDH Din D(A2) tOE tCD tLZC Dout DSEL Read Q(A1) tHZOE Q(A1) Suspend Read Q(A1) tOH tLZOE Q(A3) Read Q(A2) Suspend Write D(A 2) Read Q(A3) ADV Burst Read Q(A 3Ý01) Q(A3Ý01) ADV Burst Read Q(A 3Ý10) Q(A3Ý10) Q(A3Ý11) ADV Burst Read Q(A 3Ý11) Note: Ý = XOR when LBO = high/no connect; Ý = ADD when LBO = low. 2/10/05, v.1.1 Alliance Semiconductor 13 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Timing waveform of read/write cycle(ADSC controlled, ADSP = HIGH) tCYC tCL tCH CLK tADSCS tADSCH ADSC tAS A1 ADDRESS A5 A4 A3 A2 A7 A6 tWS tAH A8 A9 tWH GWE tCSS tCSH CE0,CE2 CE1 ADV OE tOE tLZOE Q(A1) Dout tLZOE tHZOE Q(A2) Q(A3) Q(A8) Q(A4) D(A5) READ Q(A1) 2/10/05, v.1.1 READ Q(A2) READ Q(A3) READ Q(A4) Q(A9) tDH tDS Din tOH D(A6) D(A7) WRITE WRITE WRITE D(A6) D(A7) D(A5) Alliance Semiconductor READ Q(A8) READ Q(A9) 14 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Timing waveform of power down cycle tCH tCYC tCL CLK tADSPS tADSPS ADSP ADSC A2 A1 ADDRESS tWH tWS GWE tCSS tCSH CE0,CE2 CE1 ADV OE tOE Din tLZOE tHZOE D(A2) D(A2(Ý01)) tHZC Dout Q(A1) tPUS tPDS ZZ Recovery Cycle ZZ Normal Operation Mode ZZ Setup Cycle tZZI tRZZI Isupply ISB2 READ SUSPEND Q(A1) READ Q(A1) 2/10/05, v.1.1 Sleep State Alliance Semiconductor READ SUSPEND CONQ(A2) WRITE TINUE D(A2) WRITE D(A2 Ý01) 15 of 19 AS7C331MPFD32A AS7C331MPFD36A ® AC test conditions • Output load: For tLZC, tLZOE, tHZOE, tHZC, see Figure C. For all others, see Figure B. • Input pulse level: GND to 3V. See Figure A. Thevenin equivalent: • Input rise and fall time (measured at 0.3V and 2.7V): 2 ns. See Figure A. +3.3V for 3.3V I/O; /+2.5V for 2.5V I/O • Input and output timing reference levels: 1.5V. +3.0V 90% 10% GND 90% 10% Figure A: Input waveform DOUT Z0 = 50Ω 50Ω VL = 1.5V for 3.3V I/O; 30 pF* = V DDQ/2 for 2.5V I/O Figure B: Output load (A) 319Ω/1667Ω DOUT 353Ω/1538Ω 5 pF* GND *including scope and jig capacitance Figure C: Output load(B) Notes 1 2 3 4 5 6 7 8 For test conditions, see “AC test conditions”, Figures A, B, and C. This parameter is measured with output load condition in Figure C. This parameter is sampled but not 100% tested. tHZOE is less than tLZOE, and tHZC is less than tLZC at any given temperature and voltage. tCH is measured as high if above VIH, and tCL is measured as low if below VIL. This is a synchronous device. All addresses must meet the specified setup and hold times for all rising edges of CLK. All other synchronous inputs must meet the setup and hold times for all rising edges of CLK when chip is enabled. Write refers to GWE, BWE, and BW[a:d]. Chip select refers to CE0, CE1, and CE2. 2/10/05, v.1.1 Alliance Semiconductor 16 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Package dimensions 100-pin quad flat pack (TQFP) TQFP Min Max A1 0.05 0.15 A2 1.35 1.45 b 0.22 0.38 c 0.09 0.20 D 13.90 14.10 E 19.90 20.10 e Hd D b e 0.65 nominal Hd 15.85 16.15 He 21.80 22.20 L 0.45 0.75 L1 He E 1.00 nominal α 0° 7° Dimensions in millimeters c L1 L 2/10/05, v.1.1 A1 A2 Alliance Semiconductor α 17 of 19 AS7C331MPFD32A AS7C331MPFD36A ® Ordering information Package & Width TQFP x32 TQFP x36 -200 AS7C331MPFD32A-200TQC AS7C331MPFD32A-200TQI -166 AS7C331MPFD32A-166TQC AS7C331MPFD32A-166TQI -133 AS7C331MPFD32A-133TQC AS7C331MPFD32A-133TQI AS7C331MPFD36A-200TQC AS7C331MPFD36A-200TQI AS7C331MPFD36A-166TQC AS7C331MPFD36A-166TQI AS7C331MPFD36A-133TQC AS7C331MPFD36A-133TQI Note: Add suffix ‘N’ to the above part numbers for lead free parts (Ex AS7C331MPFD32A-200TQCN) Part numbering guide AS7C 33 1M PF D 32/36 A –XXX TQ C/I X 1 2 3 4 5 6 7 8 9 10 11 1. Alliance Semiconductor SRAM prefix 2. Operating voltage: 33 = 3.3V 3. Organization: 1M = 1Meg 4. Pipelined mode 5. Deselect: D = Double cycle deselect 6. Organization: 32 = x 32; 36 = x 36 7. Production version: A = first production version 8. Clock speed (MHz) 9. Package type: TQ = TQFP 10. Operating temperature: C = commercial (0° C to 70° C); I = industrial (-40° C to 85° C) 11. N = Lead Free Part 2/10/05, v.1.1 Alliance Semiconductor 18 of 19 AS7C331MPFD32A AS7C331MPFD36A ® ® Alliance Semiconductor Corporation 2575, Augustine Drive, Santa Clara, CA 95054 Tel: 408 - 855 - 4900 Fax: 408 - 855 - 4999 www.alsc.com Copyright © Alliance Semiconductor All Rights Reserved Part Number: AS7C331MPFD32A/36A Document Version: v.1.1 © Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/ or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.