1/4 ◇Structure ◇Product name ◇Type ◇Applications ◇Functions Silicon Monolithic integrated circuit USB host AAC+WMA+MP3 Decoder LSI BU94603KV Audio products, etc. BU94603KV is AAC+WMA+MP3 decoder IC which contains USB host and SD card I/F, audio DAC, system controller, regulator for internal CORE power supply. ・USB2.0 Full Speed host I/F function contained. ・SD card I/F function contained. 2 ・ I C I/F function contained. ・ FAT analysis function contained. ・ MP3 decode function contained. (available for MPEG1, 2 and 2.5, Layer 1, 2 and 3) ・ WMA decode function contained. (available for WMA9 standard and not available for DRM) ・ AAC decode function contained. (available for MPEG4 AAC-LC and not available for DRM) ・Sample Rate Converter contained. ・ System Controller contained. ・ LED Controller contained. ・ KEY matrix Controller contained. ・ Stand Alone mode contained. ・ External processor can control. ・ Audio DAC contained. ・ Sound Effect function contained. 2 ・ Digital Audio Out(I S, S/PDIF) function contained. ・ File Name, Folder Name Sorting. ・ ID3TAG and WMATAG and AACTAG Analysis. ・ Reading a specified file data is possible from USB memory. ・ LUN is selectable. ・ Regulator for internal CORE power supply contained. ・ VQFP64pin(0.5mm pitch) ◇ Absolute maximum ratings (Ta = 25℃) Parameter Symbol Supply voltage(Analog, I/O) VDD1MAX Limits -0.3～4.5 Input voltage VIN -0.3 ～ VDD1 + 0.3 Storage temperature range TSTG -55～125 Operating temperature range TOPR -40～85 Power dissipation *1 PD 750 *1：In the case of use at Ta=25℃ or more, 7.5mW should be reduced per 1℃. Radiation resistance design is not arranged. ◇ Operating conditions Unit V Comment DVDDIO, VDD_PLL, DAVDD, AVDDC V ℃ ℃ mW (Ta = 25℃) Parameter Supply voltage(Analog, I/O) Symbol VDD1 Limits 3.0～3.6 REV. A Unit V Comment DVDDIO,VDD_PLL, DAVDD, AVDDC 2/4 ◇Electrical characteristics （Unless specified, Ta=25℃、VDD1=3.3V, DVSS=AVSSC=VSS_PLL=DAVSS=0V, XIN_PLL=16.9344MHz） Limits Parameter Symbol Unit Condition MIN. TYP. MAX. <Total > Circuit current (VDD1 USB1) Circuit current (VDD1 SD1) <Digital block> H-Level input voltage L-Level input voltage H-Level output voltage1 L-Level output voltage1 H-Level output voltage2 L-Level output voltage2 H-Level output voltage3 L-Level output voltage3 H-Level output voltage4 L-Level output voltage4 <USB-HOST > H-Level input voltage L-Level input voltage Output impedance(H) Output impedance(L) H-Level output voltage L-Level output voltage Rise/Fall time Voltage of crossing point Range of differential input Differential input sensitivity Pull-down resistance <Audio DAC> Distortion rate Dynamic range S/N ratio Max output level IDD1USB1 IDD1SD1 - 65 80 - 35 50 mA mA VIH VIL VOH1 VOL1 VOH2 VOL2 VOH3 VOL3 VOH4 VOL4 VDD1*0.7 DVSS VDD1-0.4 0 VDD1-0.4 0 VDD1-0.4 0 VDD1-1.0 0 － － － － － － － － － － VDD1 VDD1*0.3 VDD1 0.4 VDD1 0.4 VDD1 0.4 VDD1 1.0 V V V V V V V V V V VIHUSB VILUSB ZOH ZOL VOHUSB VOLUSB Tr/Tf VCRS VDIFF VSENS RPD VDD1*0.6 AVSSC 22.0 22.0 VDD1-0.5 0 － － 0.8 0.2 14.25 － － 45.0 45.0 － － 11 VDD1/2 － － 15.0 VDD1 VDD1*0.3 60.0 60.0 VDD1 0.3 － － 2.5 － 24.8 V V Ω Ω V V ns V V V kΩ THD DR S/N VSMAX － － － － 0.02 88 96 0.92 － － － － % dB dB Vrms *1 3.3V system I/O, Analog Power supply(VDD1), 1kHz, 0dB, sine-wave playing *3 1-17, 19-20, 25-26, 40, 49-52, 56, 58-61, 63 pin *4 10-11, 14-16, 48-55 pin *5 13 pin *6 21-23, 26 pin *7 41 pin *8 33, 34 pin *9 44, 46 pin REV. A *1 When USB memory is played. *1 When SD card is played. *3 *3 IOH=-1.6mA, *4 IOL=1.6mA. *4 IOH=-3.6mA, *5 IOL=3.6mA, *5 IOH=-0.6mA, *6 IOL=0.6mA, *6 IOH=-0.6mA, *7 IOL=0.6mA, *7 *8 *8 *8 *8 *8 *8 *8, Output capacity 50pF *8, Output capacity 50pF *8 *8 *8 1kHz, 0dB, sine, *9 1kHz, -60dB, sine, *9 *9 1kHz, 0dB, sine, *9 3/4 ◇Description of Terminals No. Name I/O Description of terminals 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 RESETX SEL_SLAVE SEL_MP3 SEL_DOUT SEL_VOL SEL_APLAY SEL_UTPKT TEST1 TEST2 KEY_ROW1/MCHNG KEY_ROW2/BUSY KEY_ROW3/SCL KEY_ROW4/SDA KEY_COL1/A0 KEY_COL2/A1 KEY_COL3/SEL_SMAN TEST3 DVDDIO SD_CON SD_DO SD_CLK SD_DI SD_CS DVSS TEST4 TEST5/CLKOUT12 DVDD_M2 TEST6 TEST7 TEST8 ATEST1 AVDDC USB_DM USB_DP AVSSC REXTI VOREFI VDD_PLL TEST_PLL XIN_PLL XOUT_PLL VSS_PLL DAVSS RDACO VCDACO LDACO DAVDD AMUTE LED_ERROR/TEST9 LED_PLAY/TEST10 I I I I I I I I I I/O I/O I I/O I/O I/O I/O I － I I O O O － I O － I I I O － I/O I/O － O O － I I O － － O O O － O O O O System reset terminal Slave mode selection（H：Stand Alone mode, L：Slave mode） MPEG Audio Layer selection（H：Only MP3 is playback, L：MP1, MP2 and MP3 can be playback） Digital Audio out selection（H：Disable、L：Enable） Volume operation selection（H：Volume+- Effective, L：VOL+-Invalid） At device(USB,SD) connection, Auto Play mode selection(H:It stop, L:It playback) USB test packet output selection（H：Normal operation、L：Test packet output） Pull-up to VDD1 system power supply terminal(TEST PIN) Pull-up to VDD1 system power supply terminal(TEST PIN) [KEY_ROW1]KEY Matrix terminal, [MCHNG]Music change flag terminal [KEY_ROW2]KEY Matrix terminal, [BUSY]Busy flag terminal [KEY_ROW3]KEY Matrix terminal, [SCL]I2C I/F clock terminal [KEY_ROW4]KEY Matrix terminal, [SDA]I2C I/F data terminal [KEY_COL1]KEY Matrix terminal, [A0]I2C Slave address selection [KEY_COL2]KEY Matrix terminal, [A1]I2C Slave address selection [KEY_COL3] KEY Matrix terminal, [SEL_SMAN]Manual mode selection（H：Auto, L：Manual） Pull-up to VDD1 system power supply terminal(TEST PIN) IO Power supply(VDD1) terminal SD card Connect terminal SD card Data In terminal SD card Clock terminal SD card Data Out terminal SD card Chip select terminal GND terminal Pull-up to VDD1 system power supply terminal(TEST PIN) [TEST5]Pull-up to VDD1 system power supply terminal(TEST PIN),[CLKOUT12]12MHz clock output terminal CORE Power supply(VDD2) monitor terminal. Connect to 57PIN. Pull-up to VDD1 system power supply terminal(TEST PIN) Pull-up to VDD1 system power supply terminal(TEST PIN) Pull-up to VDD1 system power supply terminal(TEST PIN) USB TEST terminal(TEST PIN) USB Power supply(VDD1)terminal USB D－I/O terminal USB D+ I/O terminal USB GND terminal USB bias resistor(12kΩ) connecting terminal USB TEST terminal(TEST PIN) PLL Power supply(VDD1) terminal PLL TEST terminal(TEST PIN) X'tal(16.9344MHz) connecting input terminal X'tal(16.9344MHz) connecting output terminal PLL GND terminal Audio DAC GND terminal Audio DAC Rch Line output terminal Audio DAC Reference voltage output terminal Audio DAC Lch Line output terminal Audio DAC Power supply(VDD1) terminal Audio Mute output terminal（H：MUTE OFF, L：MUTE ON） [LED]Lighting output terminal at ERROR, [TEST9]Pull-up to VDD1 system power supply terminal(TEST PIN) [LED]Lighting output terminal at PLAY, [TEST10]Pull-up to VDD1 system power supply terminal(TEST PIN) [LED]Lighting output terminal at PLAY for SD card, [TEST11]Pull-up to VDD1 system power supply terminal(TEST PIN) [LED]Lighting output terminal at PLAY for USB memory, [TEST12] Pull-up to VDD1 system power supply terminal(TEST PIN) [LED]Lighting output terminal when memory is being accessed,[LRCK]Digital Audio channel clock or SPDIF output terminal [LED]Lighting output terminal at PLAY for RANDOM, [BCK]Digital Audio bit clock output terminal [LED]Lighting output terminal at PLAY for REPEAT, [DATA]Digital Audio data output terminal Pull-up to VDD1 system power supply terminal(TEST PIN) CORE Power supply(VDD2) monitor terminal, Connect to bypass condenser Connect to GND(TEST PIN) Pull-up to VDD1 system power supply terminal(TEST PIN) Pull-up to VDD1 system power supply terminal(TEST PIN) Pull-up to VDD1 system power supply terminal(TEST PIN) GND terminal Connect to GND(TEST PIN) IO Power supply(VDD1) terminal 52 53 54 55 56 57 58 59 60 61 62 63 64 LED_PSD/TEST11 LED_PUSB/TEST12 LED_ACCESS LED_RANDOM LED_REPEAT TEST13 DVDD_M1 TEST14 TEST15 TEST16 TEST17 DVSS TMODE DVDDIO O O O O I － I I I I － I － REV. A 4/4 ◇ External dimensions・Block diagram 49 32 VOREFI REXTI AVSSC USB_DP USB_DM 41 40 39 38 37 36 35 34 33 32 AVDDC USB PHY PLL Audio DAC 31 ATEST1 LED_PSD/TEST11 51 BU94603KV 10.0±0.1 42 LED_ERROR/TEST9 49 LED_PLAY/TEST10 50 30 TEST8 USB Controller LED_PUSB/TEST12 52 Sound Effecter LED_ACCESS 53 29 TEST7 28 TEST6 64 1.25 Lot No. 0.5±0.15 LED_RANDOM 54 17 27 DVDD_M2 LED_REPEAT 55 1.0±0.2 DVDD_M1 57 1.25 1 0.145 +0.05 -0.03 23 SD_CS SD I/F Controller 21 SD_CLK TEST17 61 20 SD_DO System Controller 1.6MAX DVSS 62 4゜ 22 SD_DI TEST16 60 +6゜ -4゜ I2C I/F Controller TMODE 63 19 SD_CON 18 DVDDIO 10 11 12 13 14 15 KEY_COL2/A1 KEY_COL3/ SEL_SMAN TEST1 9 KEY_COL1/A0 8 KEY_ROW4/SDA 7 KEY_ROW3/SCL 6 TEST2 5 KEY_ROW1/ MCHNG KEY_ROW2/ BUSY 4 SEL_UTPKT M 3 SEL_VOL 0.08 2 SEL_APLAY +0.05 -0.04 17 TEST3 1 SEL_MP3 0.2 S RESETX 0.08 SEL_SLAVE 0.1±0.05 1.4±0.05 DVDDIO 64 0.5±0.1 TEST5/ CLKOUT12 25 TEST4 24 DVSS TEST15 59 16 1 PIN mark AAC / WMA / MP3 Decoder LDO TEST14 58 26 FAT File system TEST13 56 SEL_DOUT 12.0±0.2 VDD_PLL 43 TEST_PLL 44 XIN_PLL 45 VSS_PLL DAVSS 46 XOUT_PLL RDACO 47 LDACO 48 VCDACO 33 DAVDD 10.0±0.1 48 AMUTE 12.0±0.2 16 ( UNIT : mm ) PKG: VQFP64 Drawing No. EX252-5001-1 Figure 1. External dimension Figure 2. Block diagram ◇Caution （１） Power on Reset Please keep the terminal RESETX at the Low level when the power supply starts. After completely starting up 3.3V system power supply, afterwards, please make the terminal RESETX High level after 5us after the oscillation of the system clock is steady. Moreover, please make the terminal RESETX Low level during 5us or more when resetting it while operating. （２） About compatibility in USB memory device and SD memory card According to the file structure and communication speed of an USB memory, SD memory card, this LSI might not play back correctly. （３） About turning on the power supply Current rush might flow momentarily by the order of turning on the power supply and the delay in IC with two or more power supplies, and note the capacity of the power supply coupling, the power supply, and width and drawing the GND pattern wiring. （４） About absolute maximum rating When the absolute maximum rating such as the applied voltage and the ranges of the operating temperature is exceeded, LSI might be destroyed. Please apply neither voltage nor the temperature that exceeds the absolute maximum rating. Please execute physical measures for safety such as fuse when it is thought to exceed the absolute maximum rating, and examine it so that the condition to exceed the absolute maximum rating is not applied to LSI. （５） About GND Voltage In any state of operation must be the lowest voltage about the voltage of the terminal GND. Please actually confirm the voltage of each terminal is not a voltage that is lower than the terminal GND including excessive phenomenon. （６） About design of overheating malfunction preventive circuit Please design overheating malfunction preventive circuit with an enough margin in consideration of a permissible loss in the state of using actually. （７） About the short between terminals and the mounting by mistake Please note the direction and the gap of position of LSI enough about LSI when you mount on the substrate. LSI might be destroyed when mounting by mistake and energizing. Moreover, LSI might be destroyed when short-circuited by entering of the foreign substances between the terminal and GND, between terminals, between the terminal and the power supply of LSI. （８） About operation in strong electromagnetic field Use in strong electromagnetic field has the possibility of malfunctioning and evaluate it enough, please. REV. A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A