GBLA005 THRU GBLA10 Single Phase 4.0 AMPS. Glass Passivated Bridge Rectifiers Voltage Range 50 to 1000 Volts Current 4.0 Amperes GBL Features Glass passivated chip junction Ideal for printed circuit board High case dielectric strength Plastic material has Underwriters Laboratory Flammability Classification 94V-0 Typical IR less than 0.1µA High surge current capability High temperature soldering guaranteed: 260OC / 10 seconds / .375”, (9.5mm) lead lengths. C2.5 .146(3.70) .130(3.30) .799(20.3) .776(19.7) .445(11.3) .421(10.7) .106(2.70) .091(2.30) .047(1.20) .031(0.80) .067(1.70) .051(1.30) .043(1.10) .035(0.90) .106(2.70) .091(2.30) .551(14.0) .512(13.0) .024(0.60) .016(0.40) 1 Mechanical Data 2 205(5.20) 189(4.80) 3 4 .205(5.20) .205(5.20) .189(4.80) .189(4.80) 1 Case: Molded plastic body. Terminals: Plated leads solderable per MIL-STD-750, Method 2026. Weight: 0. 071 ounce, 2.0 grams Mounting position: Any 2 3 4 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol GBLA GBLA GBLA GBLA GBLA GBLA GBLA Units Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC = 50 (Note 1) @TA = 40 (Note 2) Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) TJ=150 Maximum Instantaneous Forward Voltage @ 4.0A Maximum DC Reverse Current @ TA=25 at Rated DC Blocking Voltage @ TA=125 Typical Thermal Resistance Per Leg (Note 1) (Note 2) Operating Temperature Range Storage Temperature Range VRRM VRMS VDC I(AV) 005 01 02 04 06 08 10 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 4.0 V V V A 3.0 IFSM 120 A VF 1.0 V IR RJA RJL TJ 5.0 500 47 10 -55 to +150 uA uA /W TSTG -55 to + 150 Notes 1. Unit Mounted on 3.0 x 3.0 x 0.11” thick (7.5 x 7.5 x 0.3cm) Al. plate. 2. Units Mounted on P.C.B. 0.5 x 0.5 “ (12x12mm) Copper Pads, 0.375”(9.5mm) Lead Length. REV.1 Oct.-2003 RATINGS AND CHARACTERISTIC CURVES (GBLA005 THRU GBLA10 ) FIG.1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 120 60 Hz Resistive or Inductive Load Heat-Sink Mounting 3.0 x 3.0 x 0.11" Thick (7.5 x 7.5 x0.3cm) Aluminum Substrate 4.0 3.0 2.0 P.C.B. Mounting 0.47 x 0.47" (12 x 12mm) Copper pads with 0.375" (9.5mm) lead length 1.0 Ta=40 C Single Half Sine-Wave (JEDEC Method) PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD RECTIFIED CURRENT. (A) 5.0 100 50 1 Cycle 0 0 0 50 100 150 10 1 O FIG.4- TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG.3- TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG INSTANTANEOUS REVERSE LEAKAGE CURRENT. (mA) INSTANTANEOUS FORWARD CURRENT. (A) 100 10 1 0.1 Tj=25 C Pulse Width=300ms 1% Duty Cycle 0.01 0.4 500 100 50 600 1 400V 1000V 0.1 Tj=25 0C 0.01 0.6 0.8 1.0 1.2 INSTANTANEOUS FORWARD VOLTAGE. (V) 1.4 1.6 0 80 20 40 60 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 100 FIG.6- TYPICAL TRANSIENT THERMAL CHARACTERISTICS 100 TRANSIENT THERMAL IMPEDANCE ( C/W) 1000 Tj=25 C JUNCTION CAPACITANCE (pF) Tj=125 0C 10 FIG.5- TYPICAL JUNCTION CAPACTITANCE PER LEG f = 1 MHz Vsig = 50mVp-p 100 50 600 10 0.1 100 NUMBER OF CYCLES AMBIENT TEMPERATURE. ( C) 400V 1000V 1 10 REVERSE VOLTAGE. (V) 100 10 1 0.1 0.01 0.1 1 T, HEATING TIME (SEC.) 10 100