D100VHI Series Miniature, 1W SIP Ultra-High Isolation DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power • 6.0 kVDC Isolation • Miniature SIP Case • Single & Dual Outputs • Miniature SIP Case • 12 Standard Models • 2.0 MH MTBF • Industry Standard Pin-Out Input Parameter Input Voltage Range Conditions Min. Typ. Max. 5 VDC Input 4.5 5.0 5.5 12 VDC Input 10.8 12.0 13.2 Input Filter VDC Internal Capacitor Reverse Polarity Input Current 0.3 A Units Output Parameter Conditions Min. Typ. Max. ±1.0 ±3.0 % Dual Output , Balanced Loads ±0.1 ±1.0 % For Vin Change of 1% ±1.2 ±1.5 % Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) See Model Selection Guide Ripple & Noise (20 MHz) (Note 2) Ripple & Noise (20 MHz) 100 Over Line, Load & Temp. Ripple & Noise (20 MHz) Output Power Protection 150 mV P - P 200 mV P - P 5 mV rms ±0.02 %/°C Max. Units 120 Temperature Coefficient % ±0.01 Output Short Circuit RoHS Compliant Units Momentary (0.5 Sec.) General Parameter Conditions Isolation Voltage Isolation Test Voltage Min. Typ. 60 Seconds 6,000 VDC Flash Tested For 1 Sec 6,600 VDC Isolation Resistance 500 VDC Isolation Capacitance 10 100 kHz, 1V Switching Frequency GΩ 15 20 pF 50 80 100 kHz Min. Typ. Max. Units +25 Environmental Parameter Conditions Operating Temperature Range Ambient -40 +70 °C Operating Temperature Range Case -40 +90 °C -40 +125 °C 95 % Storage Temperature Range MicroPower Direct Cooling 292 Page Street Suite D Stoughton, MA 02072 USA Humidity Free Air Convection RH, Non-condensing Physical Case Size 0.87 x 0.49 x 0.30 Inches (22.0 x 12.5 x 7.5 mm) Case Material T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Non-Conductive Black Plastic (UL94-V0) Weight 0.13 Oz (3.9g) Reliability Specifications Parameter MTBF Conditions Min. MIL HDBK 217F, 25°C, Gnd Benign Typ. Max. 2.0 Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions Min. Typ. Max. 5 VDC Input -0.7 9.0 12 VDC Input -0.7 18.0 Units VDC 1.5 mm From Case For 10 Sec 260 °C All Models 650 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Input Model Number Voltage (VDC) Output Load Voltage Current Current Regulation Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) Current (mA) Efficiency (%, Typ) Fuse Rating Slow-Blow (mA) Nominal Range D101VHI 5 4.5 - 5.5 303 55 5.0 200.0 4.0 10 66 500 D102VHI 5 4.5 - 5.5 291 55 12.0 80.0 2.0 8 66 500 D103VHI 5 4.5 - 5.5 295 55 15.0 65.0 1.0 8 66 500 D104VHI 5 4.5 - 5.5 303 55 ±5.0 ±100.0 ±2.0 10 66 500 D105VHI 5 4.5 - 5.5 267 55 ±12.0 ±40.0 ±1.0 8 72 500 D106VHI 5 4.5 - 5.5 287 55 ±15.0 ±35.0 ±1.0 8 73 500 D111VHI 12 10.8 - 13.2 126 30 5.0 200.0 4.0 10 66 200 D112VHI 12 10.8 - 13.2 121 30 12.0 80.0 2.0 8 66 200 D113VHI 12 10.8 - 13.2 123 30 15.0 65.0 1.0 8 66 200 D114VHI 12 10.8 - 13.2 126 30 ±5.0 ±100.0 ±2.0 10 66 200 D115VHI 12 10.8 - 13.2 108 30 ±12.0 ±40.0 ±1.0 8 74 200 D116VHI 12 10.8 - 13.2 117 30 ±15.0 ±35.0 ±1.0 8 75 200 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recomended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve Mechanical Dimensions Pin Connections Pin Single Dual 1 +Vin +Vin 2 -Vin -Vin 5 -Vout -Vout 6 No Pin Common 7 +Vout +Vout NC: No Connection Capacitive Load Single Output µF Max Dual Output µF Max 680 ±220 Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]