NI NIPCIE-8371 Pci express control of pxi express/compactpci express Datasheet

PCI Express Control of PXI Express
(MXI-Express x4 for PXI Express)
NI PXIe-PCIe8371, NI PXIe-PCIe8372, NI PCIe-8371,
NI PCIe-8372, NI PXIe-8370 Higher Throughput!
• PCI Express control of
PXI Express/CompactPCI Express
• Control of two PXI Express/CompactPCI
Express chassis from a single
PCI Express board (NI PCIe-8372)
• Sustained throughput
• 832 MB/s (2 chassis combined,
NI PXIe-PCIe8372)
• 798 MB/s (1 chassis, NI PXIe-PCIe837x)
• Cabled PCI Express spec compliant
• Software transparent link that requires
no programming
• Cabling up to 7 m
• Rugged connectivity
Overview
Cabled PCI Express Technology
With National Instruments MXI-Express x4 (“by four”) for PXI Express
interface kits, PC users with x4 or higher PCI Express slots can exercise
direct control of PXI Express systems using cabled PCI Express technology.
NI MXI-Express x4 for PXI Express, a high-bandwidth serial link transparent
to software applications and drivers provides the ability to use highperformance desktop computers, servers, and workstations to control
PXI Express systems.
The NI PCIe-8371 and NI PCIe-8372 boards provide one and two cabled
PCI Express links, respectively. The links have x4 (a link comprised of four
x1 PCI Express lanes) lane widths. The NI PXIe-8370 module connects
these PCI Express links to the PCI Express bus used in the PXI Express
chassis backplane. Thus, all PXI and PXI Express modules appear as PCI
boards within the computer itself.
PCI Express Control of PXI Express
With a MXI-Express x4 for PXI Express link, you can transparently control a
PXI Express system from a x4 or higher PCI Express slot, so you can use
desktop computers, servers, and workstations to control PXI Express systems.
MXI-Express x4 for PXI Express features a fully transparent high bandwidth
cabled PCI Express link where all PXI and PXI Express modules appear as
PCI boards within the computer itself. However, you benefit from the
increased number of slots, power and cooling per slot, module selection,
and synchronization features provided by PXI. The MXI-Express x4 for
PXI Express link consists of an NI PCIe-8371 or NI PCIe-8372 board in the PC
that is connected via a x4 MXI-Express cable to an NI PXIe-8370 module in
slot 1 of a PXI Express chassis. The NI PCIe-8371 board provides one cabled
PCI Express link, which you can cable to an NI PXIe-8370 module in a PXI
Express chassis. The NI PCIe-8372 board provides two cabled PCI Express
links, each of which you can cable to individual NI PXIe-8370 modules in
separate PXI Express chassis. Thus, you can use a single NI PCIe-8372
board and two NI PXIe-8370 modules to simultaneously control two PXI
Express systems. For your convenience, you can purchase a complete
MXI-Express x4 for PXI Express kit with all necessary components or the
PCI Express board, PXI Express module, and cable separately.
PCI Software Compatibility
PCI Express features software compatibility with PCI. Without making any
modifications to your software, you can use a MXI-Express x4 for PXI Express
link with an application written for a PXI system controlled via a PCI or
PCI Express remote controller, such as MXI-3, MXI-4, or MXI-Express.
Multichassis PXI Systems
You can use a single NI PCIe-8372 board to simultaneously control two
PXI Express systems. You also can incorporate multiple NI PCIe-8371 or
NI PCIe-8372 boards in a PC with multiple x4 or higher PCI Express slots
to add PXI Express chassis to a system. You cannot use an NI PXIe-8370
module to daisy chain multiple PXI Express chassis. However, using MXI-4,
you can connect a PXI Express chassis to PXI chassis in a star or daisy-chain
configuration within a single system. To connect a PXI Express chassis
together with a PXI chassis with MXI-4, install a National Instruments
PXI-8331 (copper) or PXI-8336 (fiber-optic) module into any PXI peripheral
slot of the master PXI Express chassis, and connect it with the appropriate
cable to a second PXI-8331 or PXI-8336 in slot 1 of the slave PXI chassis.
PCI Express Control of PXI Express (MXI-Express x4 for PXI Express)
Ordering Information
For online configuration of a complete PXI system, including chassis, modules, and all
accessories, visit ni.com/pxiadvisor.
MXI-Express x4 for PXI Express/CompactPCI Express Kit
NI PXIe-PCIe8372 ..................................................................779722-03
Kit includes one PCI Express board (NI PCIe-8372), one PXI
Express module (PXIe-8370), and one 3 m cable.
NI PXIe-PCIe8371 ..................................................................779721-03
Kit includes one PCI Express board (NI PCIe-8371), one PXI
Express module (PXIe-8370), and one 3 m cable.
PXI Express Interface Module
NI PXIe-8370..........................................................................779720-01
PCI Express MXI-Express Interface Board
NI PCIe-8372..........................................................................779724-01
NI PCIe-8371..........................................................................779723-01
x4 MXI-Express Cable
3 m ......................................................................................779725-03
7 m ......................................................................................779725-07
BUY NOW!
For complete product specifications, pricing, and accessory information,
call (866) 265 9891 (U.S. only) or go to ni.com/pxiadvisor.
BUY ONLINE at ni.com or CALL (800) 813 3693 (U.S.)
2
PCI Express Control of PXI Express (MXI-Express x4 for PXI Express)
Specifications
Specifications are subject to change without notice.
NI PCIe-8371/72
Bus Interface
Form factor............................................................................. x4 PCI Express
Slot compatibility................................................................... x4, x8, and x161 PCI Express slots
1Some motherboard manufacturers intend the x16 slot for graphics use. They may preinstall a graphics board or limit the link to x1.
Check with the motherboard manufacturer if using the x16 slot for a nongraphics board.
NI PCIe-8371 and NI PCIe-8372
Power Rail
+3.3 V
+3.3 V Aux
+12 V
Typical Current
2.5 A
1 mA
0A
Maximum Current
3.000 A
10 mA
0A
Physical
Board dimensions ..................................................................
Slot requirement ....................................................................
Maximum cable length ..........................................................
Compatibility..........................................................................
10.7 by 17.5 cm (4.4 by 6.9 in.)
One PCI Express x4 slot
7m
Fully compatible with the PCI Express Specification 1.0a
Operating Environment
Ambient temperature range .................................................. 0 to 40 °C (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2)
Operating relative humidity ................................................... 10 to 90%, noncondensing (tested in accordance with IEC-60068-2-56)
Storage Environment
Ambient temperature range .................................................. -20 to 70 °C (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2)
Relative humidity range......................................................... 5 to 95%, noncondensing (tested in accordance with IEC-60068-2-56)
NI PXIe-8370
Power Requirements
Power Rail
+3.3 V
+5 V
+12 V
+5 V Aux
Typical Current
2.2 A
1 mA
1 mA
0.3 A
Maximum Current
2.8 A
3 mA
2 mA
0.4 A
Physical
Board dimensions ..................................................................
Slot requirements ..................................................................
Maximum cable length ..........................................................
Compatibility..........................................................................
10.0 by 16.0 cm (3.9 by 6.3 in.)
One 3U PXI Express system controller slot
7m
Fully compatible with the PXI Express Hardware Specification 1.0
Environment
Maximum altitude.................................................................. 2,000 m (800 mbar) (at 25 °C ambient temperature)
Pollution degree..................................................................... 2
Indoor use only
Operating Environment
Ambient temperature range .................................................. 0 to 55 °C (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2;
meets MIL-PRF-28800F Class 3 low temperature limit and MIL-PRF-28800F Class 2
high temperature limit)
Relative humidity range......................................................... 10 to 90%, noncondensing (tested in accordance with IEC-60068-2-56)
BUY ONLINE at ni.com or CALL (800) 813 3693 (U.S.)
3
PCI Express Control of PXI Express (MXI-Express x4 for PXI Express)
Storage Environment
Ambient temperature range .................................................. -40 to 71 °C (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2;
meets MIL-PRF-28800F Class 3 limits)
Relative humidity range......................................................... 5 to 95%, noncondensing (tested in accordance with IEC-60068-2-56)
Shock
Operating shock ..................................................................... 30 g peak, half-sine, 11 ms pulse (tested in accordance with IEC-60068-2-27;
meets MIL-PRF-28800F Class 2 limits)
Vibration
Random Vibration
Operating ............................................................................... 5 to 500 Hz, 0.3 grms
Nonoperating ......................................................................... 5 to 500 Hz, 2.4 grms (tested in accordance with IEC-60068-2-64; nonoperating test
profile exceeds the requirements of MIL-PRF-28800F, Class 3)
Note: For full EMC compliance, operate this device with shielded cabling. In addition, all covers and filler panels must be installed. Refer to the
Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit
ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.
Safety and Compliance
Safety
This product is designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control,
and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CAN/CSA-C22.2 No. 61010-1
Note: For UL and other safety certifications, refer to the product label or visit ni.com/certification, search by model number or product line, and
click the appropriate link in the Certification column.
Electromagnetic Compatibility
This product is designed to meet the requirements of the following standards of EMC for electrical equipment for measurement, control,
and laboratory use:
• EN 61326 EMC requirements; Minimum Immunity
• EN 55011 Emissions; Group 1, Class A
• CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A
Note: For EMC compliance, operate this device according to product documentation.
CE Compliance
This product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows:
• 73/23/EEC; Low-Voltage Directive (safety)
• 89/336/EEC; Electromagnetic Compatibility Directive (EMC)
Note: Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this
product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers: At the end of their life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling
centers and National Instruments WEEE initiatives, visit ni.com/environment/weee.htm.
BUY ONLINE at ni.com or CALL (800) 813 3693 (U.S.)
4
NI Services and Support
SERVICE
NEEDS
NI has the services and support to meet
your needs around the globe and through
the application life cycle – from planning
and development through deployment
and ongoing maintenance. We offer
services and service levels to meet
customer requirements in research,
design, validation, and manufacturing.
Visit ni.com/services.
Training and Certification
NI training is the fastest, most certain route to productivity with our
products. NI training can shorten your learning curve, save development
time, and reduce maintenance costs over the application life cycle. We
schedule instructor-led courses in cities worldwide, or we can hold a
course at your facility. We also offer a professional certification program
that identifies individuals who have high levels of skill and knowledge on
using NI products. Visit ni.com/training.
Professional Services
Our Professional Services Team is composed of NI applications engineers,
NI Consulting Services, and a worldwide National Instruments Alliance
Partner program of more than 600 independent consultants and
integrators. Services range from
start-up assistance to turnkey
system integration.
Visit ni.com/alliance.
OEM Support
We offer design-in consulting and product integration assistance if you
want to use our products for OEM applications. For information about
special pricing and services for OEM customers, visit ni.com/oem.
ni.com • (800) 813 3693
National Instruments • [email protected]
Local Sales and Technical Support
In offices worldwide, our staff is local to the country, giving you access
to engineers who speak your language. NI delivers industry-leading
technical support through online knowledge bases, our applications
engineers, and access to 14,000 measurement and automation
professionals within NI Developer Exchange forums. Find immediate
answers to your questions at ni.com/support.
We also offer service programs that provide automatic upgrades to
your application development environment and higher levels of technical
support. Visit ni.com/ssp.
Hardware Services
NI Factory Installation Services
NI Factory Installation Services (FIS) is the fastest and easiest way to
use your PXI or PXI/SCXI combination systems right out of the box.
Trained NI technicians install the software and hardware and configure
the system to your specifications. NI extends the standard warranty by
one year on hardware components (controllers, chassis, modules)
purchased with FIS. To use FIS, simply configure your system online
with ni.com/pxiadvisor.
Calibration Services
NI recognizes the need to maintain properly calibrated devices for
high-accuracy measurements. We provide manual calibration
procedures, services to recalibrate your products, and automated
calibration software specifically designed for use by metrology
laboratories. Visit ni.com/calibration.
Repair and Extended Warranty
NI provides complete repair services for our products. Express repair
and advance replacement services are also available. We offer
extended warranties to help you meet project life-cycle requirements.
Visit ni.com/services.
*342615A-01*
342615A-01
© 2006 National Instruments Corporation. All rights reserved. MXI, National Instruments, National Instruments Alliance Partner, NI, ni.com, and SCXI
are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies.
A National Instruments Alliance Partner is a business entity independent from NI and has no agency, partnership, or joint-venture relationship with NI.
2006-7514-501-101-D
Similar pages