RoHS MLC05 Multilayer Chip Inductors Dimensions: Inches (mm) 0.063±0.006 0.031±0.006 (1.60±0.15) (0.79±0.15) *0.047±0.006 (1.19±0.15) 0.031±0.006 0.012±0.008 (0.79±0.15) (0.30±0.20) 0.023 (0.58) 0.041 (1.04) 0.031 (0.79) Allied Part Number Inductance (µh) Tolerance (%) Q Min. Test Freq. (MHz) SRF Min. (MHz) DCR Max. (Ω) IDC Max. (mA) MLC05-R01M-RC MLC05-R033M-RC .01 .033 20 20 15 15 50 50 300 270 0.20 0.20 50 50 MLC05-R047M-RC MLC05-R056M-RC MLC05-R068M-RC MLC05-R082M-RC MLC05-R10M-RC MLC05-R12M-RC MLC05-R15M-RC MLC05-R18M-RC MLC05-R22M-RC MLC05-R27M-RC MLC05-R33M-RC MLC05-R39M-RC MLC05-R47M-RC MLC05-R56M-RC MLC05-R68M-RC MLC05-R82M-RC MLC05-1R0K-RC MLC05-1R2K-RC MLC05-1R5K-RC MLC05-1R8K-RC MLC05-2R2K-RC MLC05-2R7K-RC MLC05-3R3K-RC MLC05-3R9K-RC MLC05-4R7K-RC MLC05-5R6K-RC MLC05-6R8K-RC MLC05-8R2K-RC MLC05-100K-RC MLC05-120K-RC MLC05-150K-RC MLC05-180K-RC MLC05-220K-RC MLC05-270K-RC MLC05-300K-RC .047 .056 .068 .082 .10 .12 .15 .18 .22 .27 .33 .39 .47 .56 .68 .82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 50 50 50 50 25 25 25 25 25 25 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10 4 4 4 2 2 1 1 1 1 260 255 250 245 240 205 180 165 150 136 125 110 105 95 85 75 65 60 55 50 45 40 38 36 33 22 20 18 17 15 14 13 11 10 0.30 0.30 0.30 0.30 0.50 0.50 0.60 0.60 0.80 0.80 0.85 1.00 1.35 1.50 1.70 2.10 0.60 0.80 0.80 0.95 1.10 1.30 1.50 1.70 2.10 1.55 1.70 2.10 2.55 2.60 1.70 1.80 2.10 2.70 50 50 50 50 50 50 50 50 50 50 35 35 35 35 35 35 25 25 25 25 15 15 15 15 15 5 5 5 5 3 1 1 1 1 33 10 15 15 15 15 25 25 25 25 25 25 25 25 25 25 25 25 35 35 35 35 35 35 35 35 35 35 35 30 30 30 20 20 20 20 20 1 9 2.90 1 Available in tighter tolerances. All specifications subject to change without notice. 714-665-1140 ALLIED COMPONENTS INTERNATIONAL Electrical Q vs. Frequency Characteristics: Measured on Impedance Analyzer HPA4195A. Inductance vs. Te m p e r a t u r e Characteristics: Measured on LCR Meter HP4285A. Impedance vs. Frequency Characteristics: Measured on Impedance Analyzer HPA4195A. Inductance Vs. DC Current Characteristics: Measured on LCR Meter HPA4285A. Tolerance: For 20% use M, 10% use K and 5% use J as part number suffix. Mechanical Solderability: 90% terminal coverage. Preheat: 120 ± 20° C for 60 sec. Solder: H63A. Solder Temp.: 230 ± 5°C. Flux: rosin. Dip time: 4 ± 1 sec. Environmental Thermal Shock: Inductance shall be within ±5% of initial value. Q shall be within ± 30% of initial value within temp. range of -40°C to + 85°C for 30 min. each for > 100 cycles. Humidity Resistance: Same results as above. Temp. 4° C. Humidity: 95% RH. Time: 1000 hrs. High Temp Resistance: Same results as above. Temp: 85° C. Time: 1000 hrs. Low Temp Resistance: Same results as above. Temp: -45° C. Time: 1000 hrs. Operating Temp.: Storage Temp.: -25° C to +85° C. -40° C to +85° C. Physical Packaging: 4000 pieces per 7 inch reel. www.alliedcomponents.com