ON NCV59151DS25R4G 1.5 a, very low-dropout (vldo) fast transient response regulator sery Datasheet

NCP59150, NCV59150 Series
1.5 A, Very Low-Dropout
(VLDO) Fast Transient
Response Regulator Series
http://onsemi.com
MARKING
DIAGRAMS
TAB
1
5
D2PAK
CASE 936A
Features

TAB
3
D2PAK3
CASE 936
y
59150−xx
AWLYWWG
1
1
DFN8
CASE 488AF
GND
1
VOUT
Output Current in Excess of 1.5 A
300 mV Typical Dropout Voltage at 1.5 A
Adjustable and Fixed Output Voltage Options
Low Ground Current
Fast Transient Response
Stable with Ceramic Output Capacitor
Logic Compatible Enable and Error Flag Pins
Current Limit, Reverse Current and Thermal Shutdown Protection
Operation up to 13.5 V Input Voltage
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These are Pb−Free Devices
1
VIN










y
5915z−xx
AWLYWWG
EN
VIN
GND
VOUT
FLG/ADJ
The NCP59150 series are high precision, very low dropout
(VLDO), low ground current positive voltage regulators that are
capable of providing an output current in excess of 1.5 A with a typical
dropout voltage lower than 300 mV at 1.5 A load current. The devices
are stable with ceramic output capacitors. This series consists of
Adjustable output voltage and fixed voltage versions.
The NCP59150 series can withstand up to 18 V max input voltage.
Internal protection features consist of output current limiting,
built−in thermal shutdown and reverse output current protection.
Logic level enable and error flag pins are available on the 5−pin and
8−pin versions.
The NCP59150 series Adjustable Voltage devices are available in
D2PAK−5 and DFN8 packages, the Fixed Voltage option are available
in D2PAK−5, D2PAK−3 and DFN8 packages.
Ncy59
15z−xx
ALYWG
G
Applications






Consumer and Industrial Equipment Point of Regulation
Servers and Networking Equipment
FPGA, DSP and Logic Power Supplies
Switching Power Supply Post Regulation
Battery Chargers
Functional Replacement for Industry Standard MIC29150,
MIC39150, MIC37150
xx
= Voltage Version
y
= P (NCP), V (NCV)
z
= 1 (Fix Voltage), 2 (Adj)
A
= Assembly Location
L, WL = Wafer Lot
Y, YY
= Year
W, WW = Work Week
G, G
= Pb−Free Package
(*Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
 Semiconductor Components Industries, LLC, 2013
May, 2013 − Rev. 1
1
Publication Order Number:
NCP59150/D
NCP59150, NCV59150 Series
TYPICAL APPLICATIONS
VIN = 3.0 V
+
CIN
NCP59151
VOUT = 2.5 V
VIN
VOUT
EN
FLG
100k
+
+
COUT
47 mF, Ceramic
GND
NCP59152
VIN
CIN
+
CIN
EN
ADJ
1.3 V
R1
R2
+
COUT
47 mF, Ceramic
Figure 2. Adjustable Regulator
NCP59150
VIN
VOUT
GND
Figure 1. Fixed 2.5 Regulator with Error Flag
VIN = 3.0 V
VIN
VOUT = 2.5 V
VOUT
+
COUT
47 mF, Ceramic
GND
Figure 3. Fixed 2.5 Regulator in D2PAK−3 Package
PIN FUNCTION DESCRIPTION
Pin Number
D2PAK−5
Pin Number
D2PAK−3
Pin Number
DFN8
Pin Name
Pin Function
1
−
2
EN
Enable Input: CMOS and TTL logic compatible. Logic high = enable; Logic low
= shutdown.
2
1
3
VIN
Input voltage which supplies both the internal circuitry and the current to the
output load.
3
2
1
GND
Ground
TAB
TAB
−
TAB
TAB is connected to ground.
4
3
6
VOUT
5 (Fixed)
−
8
FLG
Error Flag Open collector output.
Active−low indicates an output fault condition.
5 (Adj)
−
7 (Adj)
ADJ
Adjustable Regulator Feedback Input.
Connect to output voltage resistor divider central node.
−
−
7 (Fixed)
VOUT
SENSE
−
−
EP
EXPOSED
PAD
−
−
4, 5
NC
Linear Regulator Output.
Fixed Voltage Regulator Feedback Input.
Connect to output voltage node.
PAD for removing heat from the device. Must be connected to GND.
Not internally connected.
http://onsemi.com
2
NCP59150, NCV59150 Series
ABSOLUTE MAXIMUM RATINGS
Value
Unit
VIN
Symbol
Supply Voltage
Rating
0 to 18
V
VEN
Enable Input Voltage
0 to 18
V
VFLG
Error Flag Open Collector Output Maximum Voltage
0 to 18
V
VOUT – VIN
Reverse VOUT – VIN Voltage (EN = Shutdown or Vin = 0 V) (Note 1)
0 to 6.5
V
PD
Power Dissipation (Notes 2 and 5)
Internally Limited
TJ
Junction Temperature
−40 v TJ v +125
C
TS
Storage Temperature
−65 v TJ v +150
C
2000
200
V
ESD Rating (Notes 3 and 4)
Human Body Model
Machine Model
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
NOTE: All voltages are referenced to GND pin unless otherwise noted.
1. The ENABLE pin input voltage must be  0.8 V or Vin must be connected to ground potential.
2. PD(max) = (TJ(max) – TA) / RqJA, where RqJA depends upon the printed circuit board layout.
3. Devices are ESD sensitive. Handling precautions recommended..
4. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model (HBM) tested per AEC−Q100−002 (EIA/JESD22−A114C)
ESD Machine Model (MM) tested per AEC−Q100−003 (EIA/JESD22−A115C)
This device contains latch−up protection and exceeds 100 mA per JEDEC Standard JESD78.
5. This protection is not guaranteed outside the Recommended Operating Conditions.
RECOMMENDED OPERATING CONDITIONS (Note 6)
Symbol
Rating
Value
Unit
2.24 to 13.5
V
VIN
Supply Voltage
VEN
Enable Input Voltage
0 to 13.5
V
VFLG
Error Flag Open Collector Voltage
0 to 13.5
V
TJ
Junction Temperature
−40 v TJ v +125
C
6. The device is not guaranteed to function outside it’s Recommended operating conditions.
http://onsemi.com
3
NCP59150, NCV59150 Series
ELECTRICAL CHARACTERISTICS
TJ = 25C with VIN = VOUT nominal + 1 V; VEN = VIN; IL = 10 mA; bold values indicate –40C < TJ < +125C, unless noted.
Parameter
Conditions
Min
Typ
Max
Unit
Output Voltage Accuracy
DFN package
IL = 10 mA
−1
1
%
10 mA < IOUT < 1.5 A , VOUT nominal + 1  VIN  13.5 V
−2
2
%
Output Voltage Accuracy
D2PAK package
IL = 10 mA
−1.5
1.5
%
10 mA < IOUT < 1.5 A , VOUT nominal + 1  VIN  13.5 V
−2.5
2.5
%
Output Voltage Line Regulation
VIN = VOUT nominal + 1.0 V to 13.5 V; IL = 10 mA
0.5
%
Output Voltage Load Regulation
IL = 10 mA to 1.5 A
0.02
0.2
1.0
%
175
350
mV
IL = 1.5 A
300
500
mV
Ground Pin Current (Note 8)
IL = 1.5 A
40
60
80
mA
Ground Pin Current in Shutdown
VEN v 0.5 V
1.0
5.0
mA
Overload Protection Current Limit
VOUT = 0 V
2.0
3.0
A
Start−up Time
VEN = VIN, VOUT nominal = 2.5 V, IOUT = 10 mA,
COUT = 47 mF
100
500
ms
Output Voltage Start−up Slope
Fixed Voltage Devices
VEN = VIN, IOUT = 10 mA, COUT = 47 mF (Note 9)
40
200
ms/V
VIN – VOUT Dropout Voltage (Note 7) IL = 750 mA
ENABLE INPUT
Enable Input Signal Levels
Enable Pin Input Current
Regulator Enable
V
1.8
Regulator Shutdown
0.8
V
VEN v 0.8 V (Regulator Shutdown)
2.0
4.0
mA
30
40
mA
1.0
2.0
mA
400
500
mV
6.5 V > VEN w 1.8 V (Regulator enable)
1.0
15
FLAG OUTPUT
IFLG(leak)
Voh = 13.5 V, Flag OFF
VFLG(LO)
VIN = 2.24 V, IFLG = 1 mA, Flag ON
VFLG
Low Threshold, % of particular VOUT
210
95
%
Hysteresis, % of particular VOUT
93
2
%
High Threshold, % of particular VOUT
97
99.2
%
1.240
1.252
1.265
1.259
1.271
V
200
350
nA
NCP/NCV59152 ADJ VOLTAGE DEVICES ONLY
Reference Voltage
1.228
1.215
1.221
1.209
DFN Package
D2PAK Package
Adjust Pin Bias Current
1.240
100
7. VDO = VIN – VOUT when VOUT decreases to 98% of its nominal output voltage with VIN = VOUT + 1 V. For output voltages below 1.74 V, dropout
voltage specification does not apply due to a minimum input operating voltage of 2.24 V.
8. IIN = IGND + IOUT.
9. Fixed Voltage Device Start−up Time = Output Voltage Start−up Slope * VOUT nominal.
Package
Conditions / PCB Footprint
D2PAK–3, Junction−to−Case
Thermal Resistance
RqJC = 2.1C/W
D2PAK–5, Junction−to−Case
RqJC = 2.1C/W
mm2
D2PAK–3, Junction−to−Air
PCB with 100
2.0 oz Copper Heat Spreading Area
RqJA = 52C/W
D2PAK–5, Junction−to−Air
PCB with 100 mm2 2.0 oz Copper Heat Spreading Area
RqJA = 52C/W
DFN8, Junction−to−Air
PCB with 500 mm2 2.0 oz Copper Heat Spreading Area
RqJA = 75C/W
http://onsemi.com
4
NCP59150, NCV59150 Series
450
450
400
DROPOUT VOLTAGE (mV)
500
400
350
300
250
200
150
100
50
0
0
0.25
OUTPUT VOLTAGE (V)
250
200
150
100
0.50
0.75
1.00
1.25
0
−50 −30
1.50
10
30
50
70
90
110 130
Figure 4. Dropout Voltage vs. Output Current
(VOUTnom = 2.5 V)
Figure 5. Dropout Voltage vs. Temperature
(VOUTnom = 2.5 V, IOUT = 1.5 A)
3.0
0.5 A
2.5
1.0 A
1.0
1.5 A
0.8
0.6
0.4
2.0
10 mA
0.5 A
1.5
1.5 A
1.0
1.0 A
0.5
0.2
1.0 1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
0
2.0
1.9
1.4
1.6
1.8
2.0
2.2
2.4
2.6
SUPPLY VOLTAGE (V)
Figure 6. Dropout Characteristics
(VOUTnom = 1.24 V)
Figure 7. Dropout Characteristics
(VOUTnom = 2.5 V)
25
1.2
GROUND CURRENT (mA)
1.4
20
15
10
5
0
1.0 1.2
SUPPLY VOLTAGE (V)
30
0
−10
TEMPERATURE (C)
10 mA
1.2
GROUND CURRENT (mA)
300
OUTPUT CURRENT (A)
1.4
0
350
50
OUTPUT VOLTAGE (V)
DROPOUT VOLTAGE (mV)
TYPICAL CHARACTERISTICS
0.25
0.50
0.75
1.00
1.25
1.0
0.8
0.6
0.4
0.2
0
1.50
2.8 3.0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5 5.0
OUTPUT CURRENT (A)
SUPPLY VOLTAGE (V)
Figure 8. Ground Current vs. Output Current
(VOUTnom = 1.24 V)
Figure 9. Ground Current vs. Supply Voltage
(VOUTnom = 1.24 V, IOUT = 10 mA)
http://onsemi.com
5
NCP59150, NCV59150 Series
TYPICAL CHARACTERISTICS
2.5
50
GROUND CURRENT (mA)
GROUND CURRENT (mA)
60
40
30
1.5 A
20
1.0 A
0.5 A
10
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5 5.0
SUPPLY VOLTAGE (V)
Figure 10. Ground Current vs. Supply Voltage
(VOUTnom = 1.24 V)
Figure 11. Ground Current vs. Supply Voltage
(VOUTnom = 2.5 V, IOUT = 10 mA)
1.4
GROUND CURRENT (mA)
1.5 A
50
40
30
1.0 A
20
0.5 A
10
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
1.2
1.0
0.8
0.6
0.4
0.2
0
−50 −30
5.0
−10
10
30
50
70
90
110 130
SUPPLY VOLTAGE (V)
TEMPERATURE (C)
Figure 12. Ground Current vs. Supply Voltage
(VOUTnom = 2.5 V)
Figure 13. Ground Current vs. Temperature
(VOUTnom = 2.5 V, IOUT = 10 mA, VIN = 3.5 V)
18
45
16
40
GROUND CURRENT (mA)
GROUND CURRENT (mA)
GROUND CURRENT (mA)
1.0
SUPPLY VOLTAGE (V)
60
0
1.5
0
5.0
4.5
2.0
14
12
10
8
6
4
35
30
25
20
15
10
5
2
0
−50 −30
−10
10
30
50
70
90
110
0
−50 −30
130
−10
10
30
50
70
90
110 130
TEMPERATURE (C)
TEMPERATURE (C)
Figure 14. Ground Current vs. Temperature
(VOUTnom = 2.5 V, IOUT = 0.75 A, VIN = 3.5 V)
Figure 15. Ground Current vs. Temperature
(VOUTnom = 2.5 V, IOUT = 1.5 A, VIN = 3.5 V)
http://onsemi.com
6
NCP59150, NCV59150 Series
TYPICAL CHARACTERISTICS
2.60
90
70
2.55
PSRR (dB)
OUTPUT VOLTAGE (V)
80
2.50
2.45
60
50
Cout = 47 mF
40
30
Cout = 100 mF
20
10
2.40
−50 −30
−10
10
50
30
70
90
0
130
110
0.01
0.1
1
10
100
1000
TEMPERATURE (C)
FREQUENCY (kHz)
Figure 16. Output Voltage vs. Temperature
(VOUTnom = 2.5 V, IOUT = 10 mA)
Figure 17. PSRR vs. Frequency, Vin = 3.5 V +
200 mVpp Modulation, Vout = 2.5 V, Iout = 0.5 A
80
70
PSRR (dB)
60
50
Cout = 100 mF
40
30
20
Cout = 47 mF
10
0
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
Figure 18. PSRR vs. Frequency, Vin = 3.5 V +
200 mVpp Modulation, Vout = 2.5 V, Iout = 1.5 A
10
0.6
Vin = 2.24 V, 25C
Flag Open collector output is ON
8
Vin = 2.24 V, 25C
Flag Open collector output = Logic L
0.5
FLAG VOLTAGE (V)
FLAG CURRENT (mA)
9
7
6
5
4
3
2
0.4
0.3
0.2
0.1
1
0
0
2
4
6
8
10
12
14
16
18
0
20
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
FLAG VOLTAGE (V)
FLAG CURRENT (mA)
Figure 19. Flag Current vs. Flag Voltage
Figure 20. Flag Voltage vs. Flag Current
http://onsemi.com
7
5.0
NCP59150, NCV59150 Series
TYPICAL CHARACTERISTICS
Figure 21. Line Transient Response
Figure 22. Load Transient Response
APPLICATIONS INFORMATION
Output Capacitor and Stability
Enable Input
The NCP59150 series requires an output capacitor for
stable operation. The NCP59150 series is designed to
operate with ceramic output capacitors. The recommended
output capacitance value is 47 mF or greater. Such capacitors
help to improve transient response and noise reduction at
high frequency.
Some NCP59150 series members also feature an enable
input for on/off control of the device. It’s shutdown state
draws “zero” current from input voltage supply (only
microamperes of leakage). The enable input is TTL/CMOS
compatible for simple logic interface, but can be connected
up to VIN.
Input Capacitor
Overcurrent and Reverse Output Current Protection
An input capacitor of 1.0 mF or greater is recommended
when the device is more than 4 inches away from the bulk
supply capacitance, or when the supply is a battery. Small,
surface−mount chip capacitors can be used for the
bypassing. The capacitor should be place within 1 inch of
the device for optimal performance. Larger values will help
to improve ripple rejection by bypassing the input of the
regulator, further improving the integrity of the output
voltage.
The NCP59150 regulator is fully protected from damage
due to output current overload and output short conditions.
When NCP59150 output is overloaded, Output Current
limiting is provided. This limiting is linear; output current
during overload or output short conditions is constant. These
features are advantageous for powering FPGAs and other
ICs having current consumption higher than nominal during
their startup.
Thermal shutdown disables the NCP59150 device when
the die temperature exceeds the maximum safe operating
temperature.
When NCP59150 is disabled and (VOUT – VIN) voltage
difference is less than 6.5 V in the application, the output
structure of these regulators is able to withstand output
voltage (backup battery as example) to be applied without
reverse current flow. Of course the additional current
flowing through the feedback resistor divider inside the
Fixed Voltage devices (30 mA typically at nominal output
voltage) needs to be included in the backup battery
discharging calculations.
Minimum Load Current
The NCP59150 regulator is specified between finite
loads. A 5 mA minimum load current is necessary for proper
operation.
Error Flag
Some NCP59150 series members feature an error flag
circuit that monitors the output voltage and signals an error
condition when the voltage is 5% below the nominal output
voltage. The error flag is an open−collector output that can
sink up to 5 mA typically during a VOUT fault condition.
The FLG output is overload protected when a short circuit
of the pullup load resistor occurs in the application. This is
guaranteed in the full range of FLG output voltage Max
ratings (see Max Ratings table). Please be aware operation in
this mode is not recommended, power dissipated in the device
can impact on output voltage precision and other device
characteristics.
Adjustable Voltage Design
The NCP/NCV59152 Adjustable voltage Device Output
voltage is set by the ratio of two external resistors as shown
in Figure 23.
The device maintains the voltage at the ADJ pin at 1.24 V
referenced to ground. The current in R2 is then equal to
http://onsemi.com
8
NCP59150, NCV59150 Series
Thermal Considerations
1.24 V / R2, and the current in R1 is the current in R2 plus
the ADJ pin bias current. The ADJ pin bias current flows
from VOUT through R1 into the ADJ pin.
The output voltage can be calculated using the formula
shown in Figure 23.
NCP59152
VIN
VIN
VOUT
VOUT
+
CIN
R1
EN
The power handling capability of the device is limited by
the maximum rated junction temperature (125C). The PD
total power dissipated by the device has two components,
Input to output voltage differential multiplied by Output
current and Input voltage multiplied by GND pin current.
P D + ǒV IN * V OUTǓ @ I OUT ) V IN @ I GND
+
The GND pin current value can be found in Electrical
Characteristics table and in Typical Characteristics graphs.
The Junction temperature TJ is
COUT
47 mF,
Ceramic
ADJ
GND
T J + T A ) P D @ R qJA
R2
ǒ
(eq. 2)
where TA is ambient temperature and RqJA is the Junction to
Ambient Thermal Resistance of the NCP/NCV59150
device mounted on the specific PCB.
To maximize efficiency of the application and minimize
thermal power dissipation of the device it is convenient to
use the Input to output voltage differential as low as possible.
The static typical dropout characteristics for various
output voltage and output current can be found in the Typical
Characteristics graphs.
Ǔ
R1
) I ADJ @ R1
R2
Figure 23. Adjustable Voltage Operation
V OUT + 1.24 V @ 1 )
(eq. 1)
ORDERING INFORMATION
Output
Current
Output
Voltage
Junction Temp. Range
Package
Shipping†
NCP59150DS18R4G
1.5 A
1.8 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP59150DS25R4G
1.5 A
2.5 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP59150DS28R4G
1.5 A
2.8 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP59150DS30R4G
1.5 A
3.0 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP59150DS33R4G
1.5 A
3.3 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP59150DS50R4G
1.5 A
5.0 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCV59150DS18R4G*
1.5 A
1.8 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCV59150DS25R4G*
1.5 A
2.5 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCV59150DS28R4G*
1.5 A
2.8 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCV59150DS30R4G*
1.5 A
3.0 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCV59150DS33R4G*
1.5 A
3.3 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCV59150DS50R4G*
1.5 A
5.0 V
−40C to +125C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP59151DS18R4G
1.5 A
1.8 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and
PPAP Capable
http://onsemi.com
9
NCP59150, NCV59150 Series
ORDERING INFORMATION (continued)
Device
Output
Current
Output
Voltage
Junction Temp. Range
Package
Shipping†
D2PAK−5
800 / Tape & Reel
NCP59151DS25R4G
1.5 A
2.5 V
−40C to +125C
NCP59151DS28R4G
1.5 A
2.8 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCP59151DS30R4G
1.5 A
3.0 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCP59151DS33R4G
1.5 A
3.3 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCP59151DS50R4G
1.5 A
5.0 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCV59151DS18R4G*
1.5 A
1.8 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCV59151DS25R4G*
1.5 A
2.5 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCV59151DS28R4G*
1.5 A
2.8 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCV59151DS30R4G*
1.5 A
3.0 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCV59151DS33R4G
1.5 A
3.3 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCV59151DS50R4G
1.5 A
5.0 V
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCP59151MN18TYG
1.5 A
1.8 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCP59151MN25TYG
1.5 A
2.5 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCP59151MN28TYG
1.5 A
2.8 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCP59151MN30TYG
1.5 A
3.0 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCP59151MN33TYG
1.5 A
3.3 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCP59151MN50TYG
1.5 A
5.0 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCV59151MN18TYG
1.5 A
1.8 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCV59151MN25TYG
1.5 A
2.5 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCV59151MN28TYG
1.5 A
2.8 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCV59151MN30TYG
1.5 A
3.0 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCV59151MN33TYG
1.5 A
3.3 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCV59151MN50TYG
1.5 A
5.0 V
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCP59152MNADJTYG
1.5 A
ADJ
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
NCV59152MNADJTYG
1.5 A
ADJ
−40C to +125C
DFN8−4x4
(Pb−Free)
4000 / Tape & Reel
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and
PPAP Capable
http://onsemi.com
10
NCP59150, NCV59150 Series
ORDERING INFORMATION (continued)
Device
Output
Current
Output
Voltage
Junction Temp. Range
Package
Shipping†
NCP59152DSADJR4G
1.5 A
ADJ
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCV59152DSADJR4G
1.5 A
ADJ
−40C to +125C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and
PPAP Capable
http://onsemi.com
11
NCP59150, NCV59150 Series
PACKAGE DIMENSIONS
D2PAK 5
CASE 936A−02
ISSUE C
−T−
OPTIONAL
CHAMFER
A
TERMINAL 6
E
U
S
K
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A
AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 6.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED 0.025
(0.635) MAXIMUM.
V
H
1 2 3 4 5
M
D
0.010 (0.254)
M
T
DIM
A
B
C
D
E
G
H
K
L
M
N
P
R
S
U
V
P
N
G
L
R
C
SOLDERING FOOTPRINT
8.38
0.33
1.702
0.067
10.66
0.42
16.02
0.63
3.05
0.12
SCALE 3:1
5−LEAD D2PAK
http://onsemi.com
12
1.016
0.04
mm Ǔ
ǒinches
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.067 BSC
0.539
0.579
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 _ REF
0.116 REF
0.200 MIN
0.250 MIN
MILLIMETERS
MIN
MAX
9.804
10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
1.702 BSC
13.691
14.707
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 _ REF
2.946 REF
5.080 MIN
6.350 MIN
NCP59150, NCV59150 Series
PACKAGE DIMENSIONS
D2PAK
CASE 936−03
ISSUE D
T
C
A
K
S
B
J
2
ES
DETAIL C
DETAIL C
3
F
G
SIDE VIEW
2X
TOP VIEW
D
0.010 (0.254)
N
M
P
R
C
OPTIONAL
CHAMFER
V
H
1
U
ED
OPTIONAL
CHAMFER
T
TERMINAL 4
L
SIDE VIEW
BOTTOM VIEW
DUAL GAUGE
CONSTRUCTION
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCHES.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS
A AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 4.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.025 (0.635) MAXIMUM.
6. SINGLE GAUGE DESIGN WILL BE SHIPPED
AFTER FPCN EXPIRATION IN OCTOBER 2011.
SINGLE GAUGE
CONSTRUCTION
T
M
T
SEATING
PLANE
BOTTOM VIEW
DETAIL C
OPTIONAL CONSTRUCTIONS
SOLDERING FOOTPRINT*
10.490
8.380
16.155
2X
3.504
2X
1.016
5.080
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
13
DIM
A
B
C
D
ED
ES
F
G
H
J
K
L
M
N
P
R
S
U
V
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.018
0.026
0.051 REF
0.100 BSC
0.539
0.579
0.125 MAX
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 _ REF
0.116 REF
0.200 MIN
0.250 MIN
MILLIMETERS
MIN
MAX
9.804 10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
0.457
0.660
1.295 REF
2.540 BSC
13.691 14.707
3.175 MAX
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 _ REF
2.946 REF
5.080 MIN
6.350 MIN
NCP59150, NCV59150 Series
PACKAGE DIMENSIONS
DFN8, 4x4
CASE 488AF
ISSUE C
A
B
D
PIN ONE
REFERENCE
2X
0.15 C
2X
0.10 C
8X
0.08 C
NOTE 4
L1
ÉÉ
ÉÉ
0.15 C
DETAIL A
E
OPTIONAL
CONSTRUCTIONS
EXPOSED Cu
DETAIL B
ÇÇÇÇ
A
(A3)
A1
8
ÇÇÇ
ÉÉÉ
A1
C
ALTERNATE
CONSTRUCTIONS
SEATING
PLANE
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.25
0.35
4.00 BSC
1.91
2.21
4.00 BSC
2.09
2.39
0.80 BSC
0.20
−−−
0.30
0.50
−−−
0.15
SOLDERING FOOTPRINT*
ÇÇÇ
Ç
Ç ÇÇ
1
MOLD CMPD
A3
DETAIL B
D2
K
ÇÇ
ÇÇ
ÉÉ
ÉÉ
TOP VIEW
SIDE VIEW
DETAIL A
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. DETAILS A AND B SHOW OPTIONAL
CONSTRUCTIONS FOR TERMINALS.
L
L
8X
L
2.21
4
5
e
8X
0.63
E2
8X
4.30 2.39
b
PACKAGE
OUTLINE
0.10 C A B
0.05 C
NOTE 3
BOTTOM VIEW
8X
0.80
PITCH
0.35
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
14
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP59150/D