ISL84781 ® Data Sheet July 31, 2006 Ultra Low ON-Resistance, Low-Voltage, Single Supply, 8 to 1 Analog Multiplexer The Intersil ISL84781 device contains precision, bidirectional, analog switches configured as an 8 channel multiplexer/demultiplexer. It is designed to operate from a single +1.6V to +3.6V supply. The device has an inhibit pin to simultaneously open all signal paths. ON resistance is 0.4Ω with a +3.0V supply and 0.55Ω with a single +1.8V supply. Each switch can handle rail to rail analog signals. The off-leakage current is only 4nA max at +25°C or 40nA max at +85°C with a +3.3V supply. All digital inputs are 1.8V logic-compatible when using a single +3V supply. The ISL84781 is a 8 to 1 multiplexer device that is offered in a 16 Ld TSSOP package, and a 16 Ld thin QFN package. Table 1 summarizes the performance of this family. FN6095.3 Features • Pin Compatible Replacement for the MAX4781, and MAX4617 • ON Resistance (RON) - V+ = +3.0V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4Ω - V+ = +1.8V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.55Ω • RON Matching Between Channels. . . . . . . . . . . . . . . . 0.12Ω • RON Flatness Across Signal Range . . . . . . . . . . . . . .0.056Ω • Single Supply Operation. . . . . . . . . . . . . . . . . +1.6V to +3.6V • Low Power Consumption (PD). . . . . . . . . . . . . . . . . . <0.2µW • Fast Switching Action (VS = +3V) - tON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16ns - tOFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13ns • Guaranteed Break-Before-Make • High Current Handling Capacity (300mA Continuous) TABLE 1. FEATURES AT A GLANCE • Available in 16 Ld TSSOP and 16 Ld 3x3 Thin QFN ISL84781 • 1.8V CMOS-Logic Compatible (+3V Supply) Configuration 8:1 Mux 3V RON 0.4Ω 3V tON/tOFF 16ns/13ns 1.8V RON 0.55Ω 1.8V tON/tOFF 24ns/16ns Packages 16 Ld TSSOP, 16 Ld 3x3 thin QFN • Pb-Free Plus Anneal Available (RoHS Compliant) • ISL84781IR Replaces the ISL43L680IR. Applications Related Literature • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” • Battery Powered, Handheld, and Portable Equipment - Cellular/Mobile Phones - Pagers - Laptops, Notebooks, Palmtops • Portable Test and Measurement • Medical Equipment • Audio Switching and Routing • Application Note AN557 “Recommended Test Procedures for Analog Switches” 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL84781 (Note 1) 15 NO2 COM 3 14 NO1 NO7 4 NO5 5 15 14 13 12 NO1 13 NO0 NO7 2 11 NO0 12 NO3 NO5 3 10 NO3 INH 4 9 N.C. 7 10 ADD1 GND 8 9 ADD2 5 6 7 8 ADD1 1 ADD2 COM 11 ADD0 LOGIC 16 GND INH 6 NO2 NO6 2 V+ 16 V+ NO4 NO4 1 ISL84781IR (3x3 THIN QFN) TOP VIEW NO6 ISL84781IV (TSSOP) TOP VIEW N.C. Pinouts ADD0 NOTE: 1. Switches Shown for Logic “0” Inputs. Truth Table Ordering Information PART MARKING TEMP. RANGE (°C) PACKAGE PKG. DWG. # ISL84781IV 84781IV -40 to 85 16 Ld TSSOP M16.173 ISL84781IV-T 84781IV -40 to 85 16 Ld TSSOP Tape & Reel M16.173 ISL84781 INH ADD2 ADD1 ADD0 SWITCH ON 1 X X X NONE 0 0 0 0 NO0 0 0 0 1 NO1 0 0 1 0 NO2 ISL84781IR 781I -40 to 85 16 Ld TQFN L16.3x3A 0 0 1 1 NO3 ISL84781IR-T 781I -40 to 85 16 Ld TQFN Tape & Reel L16.3x3A 0 1 0 0 NO4 0 1 NO5 -40 to 85 16 Ld TSSOP (Pb-free) M16.173 1 ISL84781IVZ (See Note) 84781IVZ 0 0 1 1 0 NO6 0 1 1 1 NO7 NOTE: Care. Logic “0” ≤0.5V. Logic “1” ≥1.4V, with a 3V supply. X = Don’t Pin Descriptions PIN V+ FUNCTION System Power Supply Input (1.6V to 3.6V) N.C. No Connect. Not internally connected. GND Ground Connection INH Digital Control Input. Connect to GND for Normal Operation. Connect to V+ to turn all switches off. COM Analog Switch Common Pin NO0 NO7 Analog Switch Input Pin ADD Address Input Pin 2 PART NO. ISL84781IVZ-T 84781IVZ (See Note) -40 to 85 16 Ld TSSOP M16.173 Tape and Reel (Pb-free) ISL8478IRZ (See Note) 781Z -40 to 85 16 Ld TQFN (Pb-free) ISL8478IRZ-T (See Note) 781Z L16.3x3A -40 to 85 16 Ld TQFN Tape and Reel (Pb-free) L16.3x3A Add “-T” suffix for tape and reel. NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD020C. FN6095.3 July 31, 2006 ISL84781 Absolute Maximum Ratings Thermal Information V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V Input Voltages INH, NO, ADD (Note 2) . . . . . . . . . . . . . . . . . -0.3 to (V+) + 0.3V Output Voltages COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (V+) + 0.3V Continuous Current NO or COM . . . . . . . . . . . . . . . . . . . . . ±300mA Peak Current NO or COM (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±500mA ESD Rating HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >4kV MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >300V CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >1000V Thermal Resistance (Typical, Note 3) θJA (°C/W) 16 Ld TSSOP Package . . . . . . . . . . . . . . . . . . . . . . 150 16 Ld 3x3 Thin QFN Package . . . . . . . . . . . . . . . . . 75 Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C (Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 2. Signals on NO, COM, ADD, or INH exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings. 3. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications - 3V Supply Test Conditions: VSUPPLY = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Notes 4, 8), Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 5) MIN Full 0 - V+ V 25 - 0.41 0.75 Ω TYP (NOTE 5) MAX UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON Resistance, RON V+ = 2.7V, ICOM = 100mA, VNO = 0V to V+, (See Figure 5) RON Matching Between Channels, ΔRON V+ = 2.7V, ICOM = 100mA, VNO = Voltage at max RON, (Note 6) RON Flatness, RFLAT(ON) V+ = 2.7V, ICOM = 100mA, VNO = 0V to V+, (Note 7 NO OFF Leakage Current, INO(OFF) V+ = 3.3V, VCOM = 0.3V, 3V, VNO = 3V, 0.3V, (Note 8) COM ON Leakage Current, ICOM(ON) V+ = 3.3V, VCOM = VNO = 0.3V, 3V, (Note 8) Full - - 0.8 Ω 25 - 0.12 0.2 Ω Full - - 0.2 Ω 25 - 0.056 0.15 Ω Full - - 0.15 Ω 25 -4 - 4 nA Full -40 - 40 nA 25 -15 - 15 nA Full -70 - 70 nA Input Voltage High, VINH, VADDH Full 1.4 - - V Input Voltage Low, VINL, VADDL Full - - 0.5 V V+ = 3.6V, VINH = VADD = 0V or V+ (Note 9) Full -0.5 - 0.5 μA Inhibit Turn-ON Time, tON V+ = 2.7V, VNO = 1.5V, RL = 50Ω, CL = 35pF, (See Figure 1, Note 9) 25 - 16 25 ns Inhibit Turn-OFF Time, tOFF V+ = 2.7V, VNO = 1.5V, RL = 50Ω, CL = 35pF, (See Figure 1, Note 9) Address Transition Time, tTRANS V+ = 2.7V, VNO = 1.5V, RL = 50Ω, CL = 35pF, (See Figure 1, Note 9) Break-Before-Make Time, tBBM V+ = 3.3V, VNO = 1.5V, RL = 50Ω, CL = 35pF, (See Figure 3, Note 9) Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω, (See Figure 2) Input OFF Capacitance, COFF f = 1MHz, VNO = VCOM = 0V, (See Figure 6) DIGITAL INPUT CHARACTERISTICS Input Current, IINH, IINL, IADDH, IADDL DYNAMIC CHARACTERISTICS 3 Full - - 27 ns 25 - 14 23 ns Full - - 25 ns 25 - 19 28 ns Full - - 30 ns 25 - 4 - ns Full 1 - - ns 25 - -39 - pC 25 - 65 - pF FN6095.3 July 31, 2006 ISL84781 Electrical Specifications - 3V Supply Test Conditions: VSUPPLY = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Notes 4, 8), Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 5) MIN TYP (NOTE 5) MAX UNITS COM OFF Capacitance, COFF f = 1MHz, VNO = VCOM = 0V, (See Figure 6) 25 - 470 - pF COM ON Capacitance, CCOM(ON) f = 1MHz, VNO = VCOM = 0V, (See Figure 6) 25 - 485 - pF OFF Isolation RL = 50Ω, CL = 35pF, f = 100kHz, (See Figure 4) 25 - 65 - dB Total Harmonic Distortion (THD) f = 20Hz to 20kHz, 0.5Vp-p, RL = 32Ω 25 - 0.014 - % Full 1.6 - 3.6 V 25 - - 0.05 μA Full - - 1.2 μA POWER SUPPLY CHARACTERISTICS Power Supply Range V+ = 3.6V, VINH, VADD = 0V or V+, Switch On or Off Positive Supply Current, I+ NOTES: 4. VIN = Input voltage to perform proper function. 5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 6. RON matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron value. 7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range. 8. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation. 9. Guaranteed but not tested. Electrical Specifications: 1.8V Supply Test Conditions: V+ = +1.8V, GND = 0V, VINH = 1V, VINL = 0.4V (Notes 4, 8), Unless Otherwise Specified TEMP (°C) MIN (NOTE 5) Full 0 - V+ V 25 - 0.55 0.85 Ω Full - - 0.9 Ω 25 - 0.1 - Ω Full - 0.13 - Ω 25 - 0.14 - Ω Full - 0.16 - Ω Input Voltage High, VINH, VADDH Full 1 - - V Input Voltage Low, VINL, VADDL Full - - 0.4 V Full -0.5 - 0.5 μA PARAMETER TEST CONDITIONS TYP MAX (NOTE 5) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON Resistance, RON V+ = 1.8V, ICOM = 10.0mA, VNO = 1.0V, (See Figure 5) RON Matching Between Channels, ΔRON) V+ = 1.8V, ICOM = 10.0mA, VNO = 1.0V, (See Figure 5) RON Flatness, RFLAT(ON) V+ = 1.8V, ICOM = 10.0mA, VNO = 0V, 0.9V, 1.6V, (See Figure 5) DIGITAL INPUT CHARACTERISTICS Input Current, IINH, IINL, IADDH, IADDL V+ = 1.8V, VINH, VADD = 0V or V+ (Note 9) DYNAMIC CHARACTERISTICS V+ = 1.8V, VNO = 1.0V, RL = 50Ω, CL = 35pF, (See Figure 1, Note 9) Inhibit Turn-ON Time, tON Inhibit Turn-OFF Time, tOFF V+ = 1.8V, VNO = 1.0V, RL = 50Ω, CL = 35pF, (See Figure 1, Note 9) Address Transition Time, tTRANS V+ = 1.8V, VNO = 1.0V, RL = 50Ω, CL = 35pF, (See Figure 1, Note 9) 25 - 24 33 ns Full - - 35 ns 25 - 16 25 ns Full - - 27 ns 25 - 25 34 ns Full - - 36 ns Break-Before-Make Time, tBBM V+ = 1.8V, VNO = 1.0V, RL = 50Ω, CL = 35pF, (See Figure 3, Note 9) 25 - 9 - ns Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω, (See Figure 2) 25 - -20 - pC 4 FN6095.3 July 31, 2006 ISL84781 Test Circuits and Waveforms V+ C V+ LOGIC INPUT C tr < 5ns tf < 5ns 50% VNO0 0V NO0 tON NO1-NO7 VOUT COM INH VNO0 90% SWITCH OUTPUT VOUT 90% GND ADD2-0 LOGIC INPUT CL 35pF RL 50Ω 0V tOFF Logic input waveform is inverted for switches that have the opposite logic sense. Repeat test for other switches. CL includes fixture and stray capacitance. RL V OUT = V NOx -----------------------------R L + R ( ON ) FIGURE 1B. INHIBIT tON/tOFF TEST CIRCUIT FIGURE 1A. INHIBIT tON/tOFF MEASUREMENT POINTS V+ LOGIC INPUT tr < 5ns tf < 5ns 50% V+ C C 0V tTRANS VNO0 NO1-NO7 VOUT VNO0 NO0 90% SWITCH OUTPUT ADD2-0 GND COM VOUT INH CL 35pF RL 50Ω LOGIC INPUT 10% VNO7 0V tTRANS Logic input waveform is inverted for switches that have the opposite logic sense. Repeat test for other switches. CL includes fixture and stray capacitance. RL -----------------------------V OUT = V NOx R + R L ( ON ) FIGURE 1D. ADDRESS tTRANS TEST CIRCUIT FIGURE 1C. ADDRESS tTRANS MEASUREMENT POINTS FIGURE 1. SWITCHING TIMES V+ C V+ LOGIC INPUT OFF OFF ON VOUT RG COM NOx 0V 0Ω SWITCH OUTPUT VOUT ΔVOUT ADD2 ADD1 ADD0 VG CHANNEL SELECT GND INH LOGIC INPUT CL 1000pF Q = ΔVOUT x CL FIGURE 2A. Q MEASUREMENT POINTS Repeat test for other switches. FIGURE 2B. Q TEST CIRCUIT FIGURE 2. CHARGE INJECTION 5 FN6095.3 July 31, 2006 ISL84781 Test Circuits and Waveforms (Continued) V+ C C tr < 5ns tf < 5ns V+ LOGIC INPUT NO0-NO7 VNOx 0V SWITCH OUTPUT VOUT COM LOGIC INPUT 90% VOUT CL 35pF RL 50Ω ADD2-0 GND INH 0V tBBM Repeat test for other switches. CL includes fixture and stray capacitance. FIGURE 3A. tBBM MEASUREMENT POINTS FIGURE 3B. tBBM TEST CIRCUIT FIGURE 3. BREAK-BEFORE-MAKE TIME V+ V+ 10nF C RON = V1/100mA SIGNAL GENERATOR NOx NOx VNX 0V or V+ ADD2 ADD1 ADD0 100mA 0V or V+ V1 CHANNEL SELECT ADD2 ADD1 ADD0 0V or V+ ANALYZER COM GND COM INH GND INH CHANNEL SELECT RL Off-Isolation is measured between COM and “Off” NO terminal on each switch. Signal direction through switch is reversed and worst case values are recorded. FIGURE 4. OFF ISOLATION TEST CIRCUIT FIGURE 5. RON TEST CIRCUIT V+ C NOx 0V or V+ 1MHz IMPEDANCE ANALYZER ADD2 ADD1 ADD0 COM GND INH Channel Select FIGURE 6. CAPACITANCE TEST CIRCUIT 6 FN6095.3 July 31, 2006 ISL84781 Detailed Description Power-Supply Considerations The ISL84781 analog multiplexer offers precise switching capability from a single 1.6V to 3.6V supply with ultra low onresistance (0.41Ω) and high speed operation (tON = 16ns, tOFF = 13ns) with +3V supply. The device is especially wellsuited for portable battery powered equipment thanks to the low operating supply voltage (1.6V), low power consumption (0.2μW), and low leakage currents (70nA max). High frequency applications also benefit from the wide bandwidth, and the very high off isolation and crosstalk rejection. The ISL84781 construction is typical of most single supply CMOS analog multiplexers, in that it has two supply pins: V+ and GND. V+ and GND drive the internal CMOS switches and set its analog voltage limits. Unlike switches with a 4V maximum supply voltage, the ISL84781 4.7V maximum supply voltage provides plenty of room for the 10% tolerance of 3.6V supplies, as well as room for overshoot and noise spikes. Supply Sequencing and Overvoltage Protection With any CMOS device, proper power supply sequencing is required to protect the device from excessive input currents which might permanently damage the IC. All I/O pins contain ESD protection diodes from the pin to V+ and to GND (See Figure 7). To prevent forward biasing these diodes, V+ must be applied before any input signals, and the input signal voltages must remain between V+ and GND. If these conditions cannot be guaranteed, then one of the following two protection methods should be employed. Logic inputs can easily be protected by adding a 1kΩ resistor in series with the input (see Figure 7). The resistor limits the input current below the threshold that produces permanent damage, and the sub-microamp input current produces an insignificant voltage drop during normal operation. This method is not applicable for the signal path inputs. Adding a series resistor to the switch input defeats the purpose of using a low RON switch, so two small signal diodes can be added in series with the supply pins to provide overvoltage protection for all pins (see Figure 7). These additional diodes limit the analog signal from 1V below V+ to 1V above GND. The low leakage current performance is unaffected by this approach, but the switch signal range is reduced and the resistance may increase, especially at low supply voltages. OPTIONAL PROTECTION RESISTOR FOR LOGIC INPUTS 1kΩ OPTIONAL PROTECTION DIODE V+ LOGIC VNOx VCOM GND OPTIONAL PROTECTION DIODE FIGURE 7. OVERVOLTAGE PROTECTION 7 The minimum recommended supply voltage is 1.6V but the part will operate with a supply below 1.5V. It is important to note that the input signal range, switching times, and onresistance degrade at lower supply voltages. Refer to the electrical specification tables and Typical Performance curves for details. V+ and GND power the internal logic and level shifters. The level shifters convert the logic levels to switched V+ and GND signals to drive the analog switch gate terminals. These multiplexers cannot be operated with bipolar supplies, because the input switching point becomes negative in this configuration. Logic-Level Thresholds This device is 1.8V CMOS compatible (0.5V and 1.4V) over a supply range of 2.0V to 3.6V (See Figure 12). At 3.6V the VIH level is about 1.27V. This is still below the 1.8V CMOS guaranteed high output minimum level of 1.4V, but noise margin is reduced. The digital input stages draw supply current whenever the digital input voltage is not at one of the supply rails. Driving the digital input signals from GND to V+ with a fast transition time minimizes power dissipation. High-Frequency Performance In 50Ω systems, signal response is reasonably flat even past 10MHz with a -3dB bandwidth of 52MHz (See Figure 16). The frequency response is very consistent over a wide V+ range, and for varying analog signal levels. An OFF switch acts like a capacitor and passes higher frequencies with less attenuation, resulting in signal feed through from a switch’s input to its output. Off Isolation is the resistance to this feed through. Figure 17 details the high Off Isolation provided by these devices. At 100kHz, Off Isolation is about 65dB in 50Ω systems, decreasing approximately 20dB per decade as frequency increases. Higher load impedances decrease Off Isolation due to the voltage divider action of the switch OFF impedance and the load impedance. Leakage Considerations Reverse ESD protection diodes are internally connected between each analog-signal pin and both V+ and GND. One of these diodes conducts if any analog signal exceeds V+ or GND. FN6095.3 July 31, 2006 ISL84781 Virtually all the analog leakage current comes from the ESD diodes to V+ or GND. Although the ESD diodes on a given signal pin are identical and therefore fairly well balanced, they are reverse biased differently. Each is biased by either V+ or GND and the analog signal. This means their leakages will vary as the signal varies. The difference in the two diode leakages to the V+ and GND pins constitutes the analog- signal-path leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal. This is why both sides of a given switch can show leakage currents of the same or opposite polarity. There is no connection between the analog signal paths and V+ or GND. Typical Performance Curves TA = 25°C, Unless Otherwise Specified 0.75 0.55 V+ = 3V ICOM = 100mA ICOM = 100mA 0.7 V+ = 1.65V 0.5 0.65 85°C 0.55 RON (Ω) RON (Ω) 0.6 V+ = 1.8V 0.5 0.45 25°C 0.4 0.45 0.35 V+ = 2.7V -40°C 0.4 0.35 V+ = 3V V+ = 3.6V 0 1 2 0.3 3 0 4 0.5 1 2 2.5 3 FIGURE 9. ON RESISTANCE vs SWITCH VOLTAGE FIGURE 8. ON RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE -10 0.7 V+ = 1.8V ICOM = 100mA 0.65 -20 -30 0.6 -40 V+ = 1.8V 85°C -50 0.55 -60 Q (pC) RON (Ω) 1.5 VCOM (V) VCOM (V) 0.5 25°C 0.45 -70 -80 -90 0.4 -40°C -100 0.35 V+ = 3V -110 -120 0.3 0 0.5 1 1.5 VCOM (V) FIGURE 10. ON RESISTANCE vs SWITCH VOLTAGE 8 2 0 0.5 1 1.5 2 2.5 3 VCOM (V) FIGURE 11. CHARGE INJECTION vs SWITCH VOLTAGE FN6095.3 July 31, 2006 ISL84781 Typical Performance Curves TA = 25°C, Unless Otherwise Specified (Continued) 1.6 60 1.4 1.2 VINH tRANS (ns) VINH AND VINL (V) 50 1 30 VINL 0.8 40 85°C 25°C 20 0.6 -40°C 1 1.5 2 2.5 3 3.5 4 10 4.5 1 1.5 2 2.5 3 V+ (V) V+ (V) FIGURE 12. DIGITAL SWITCHING POINT vs SUPPLY VOLTAGE 3.5 4 4.5 FIGURE 13. ADDRESS TRANS TIME vs SUPPLY VOLTAGE 25 60 50 tOFF (ns) tON (ns) 20 40 30 85°C 25°C 85°C 25°C 15 -40°C -40°C 20 10 10 1 1.5 2 2.5 3 V+ (V) 3.5 4 3 3.5 0 4 4.5 10 V+ = 3V GAIN 0 PHASE 20 40 60 80 RL = 50Ω VIN = 0.2VP-P to 2VP-P 100 1 10 FREQUENCY (MHz) FIGURE 16. FREQUENCY RESPONSE 9 100 OFF ISOLATION (dB) -10 PHASE (DEGREES) NORMALIZED GAIN (dB) 2.5 FIGURE 15. INHIBIT TURN-OFF TIME vs SUPPLY VOLTAGE V+ = 3V 0.1 2 V+ (V) FIGURE 14. INHIBIT TURN-ON TIME vs SUPPLY VOLTAGE 0 1.5 1 4.5 -10 20 -20 30 -30 40 -40 50 -50 60 ISOLATION -60 70 -70 80 -80 90 -90 100 -100 1k 10k 100k 1M 10M 110 100M 500M FREQUENCY (Hz) FIGURE 17. OFF ISOLATION FN6095.3 July 31, 2006 ISL84781 Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND (QFN Paddle Connection: To Ground or Float) TRANSISTOR COUNT: 228 PROCESS: Submicron CMOS 10 FN6095.3 July 31, 2006 ISL84781 Thin Shrink Small Outline Plastic Packages (TSSOP) M16.173 N 16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE INDEX AREA E 0.25(0.010) M E1 2 INCHES GAUGE PLANE -B1 B M 0.05(0.002) -A- SYMBOL MIN MAX MIN MAX NOTES A - 0.043 - 1.10 - A1 3 L A D -C- e α A1 b 0.10(0.004) M 0.25 0.010 SEATING PLANE c 0.10(0.004) C A M 0.05 0.15 - A2 0.033 0.037 0.85 0.95 - b 0.0075 0.012 0.19 0.30 9 c 0.0035 0.008 0.09 0.20 - B S 0.002 D 0.193 0.201 4.90 5.10 3 0.169 0.177 4.30 4.50 4 0.026 BSC E 0.246 L 0.020 N α NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-153-AB, Issue E. 0.006 E1 e A2 MILLIMETERS 0.65 BSC 0.256 6.25 0.028 0.50 16 0o - 0.70 6 16 8o 0o - 6.50 7 8o Rev. 1 2/02 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (Angles in degrees) 11 FN6095.3 July 31, 2006 ISL84781 Thin Quad Flat No-Lead Plastic Package (TQFN) Thin Micro Lead Frame Plastic Package (TMLFP) ) 2X L16.3x3A 0.15 C A D A 16 LEAD THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE 9 D/2 MILLIMETERS D1 D1/2 2X N 6 INDEX AREA 0.15 C B 1 2 3 E1/2 E/2 MIN NOMINAL MAX NOTES A 0.70 0.75 0.80 - A1 - - 0.05 - A2 - - 0.80 9 0.30 5, 8 A3 E1 E b 9 0.20 REF 0.18 D 2X B TOP VIEW 0.15 C A A2 A D2 / / 0.10 C 0 C A3 SIDE VIEW 9 5 NX b 4X P E 3.00 BSC - 2.75 BSC 9 1.35 1.50 1.65 7, 8, 10 0.50 BSC - k 0.20 - - - L 0.30 0.40 0.50 8 2 8 Nd 4 3 NX k Ne 4 3 D2 2 N 1 (DATUM A) 2 3 6 INDEX AREA 8 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 5 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. SECTION "C-C" C L 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. L TERMINAL TIP FOR ODD TERMINAL/SIDE 9 4. All dimensions are in millimeters. Angles are in degrees. A1 e 9 12 3. Nd and Ne refer to the number of terminals on each D and E. NX b 10 0.60 - 2. N is the number of terminals. BOTTOM VIEW C L - - NOTES: 9 CORNER OPTION 4X (Nd-1)Xe REF. - θ 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. E2/2 N e P Rev. 0 6/04 (Ne-1)Xe REF. E2 7 NX L C C 7, 8, 10 16 7 L1 9 1.65 N 4X P 8 1.50 0.10 M C A B D2 (DATUM B) A1 - 2.75 BSC 1.35 e SEATING PLANE 9 E1 E2 0.08 C 0.23 3.00 BSC D1 0.15 C B 2X 4X SYMBOL L1 10 L e FOR EVEN TERMINAL/SIDE 9. Features and dimensions A2, A3, D1, E1, P & θ are present when Anvil singulation method is used and not present for saw singulation. 10. Compliant to JEDEC MO-220WEED-2 Issue C, except for the E2 and D2 MAX dimension. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 12 FN6095.3 July 31, 2006