CREE LC503TPG1-30Q-A1 5-mm round led Datasheet

Cree® 5-mm Round LED
Model # LC503TPG1-30Q-A1
Data Sheet
30-degree, 5-mm LED lamp in green color with water-transparent lens and no stopper
Applications
•
•
•
•
Advertising Signs
Indicators
LCD Back Lights
Moving-Message Signs
Absolute Maximum Ratings (TA = 25°C)
Items
Symbol
Absolute Maximum Rating
Unit
IF
25
mA
IFP
100
mA
Reverse Voltage
VR
5
V
Power Dissipation
PD
100
mW
Operation Temperature
Topr
-40 ~ +95
°C
Storage Temperature
Tstg
-40 ~ +100
°C
Lead Soldering Temperature
Tsol
Forward Current
Peak Forward Current
Note
Max. 260°C for 3 sec. max.
(3 mm from the base of the epoxy bulb)
Note: Pulse width ≤0.1 msec, duty ≤1/10.
Typical Electrical & Optical Characteristics (TA = 25°C)
Characteristics
Symbol
Condition
Unit
Forward Voltage
VF
IF = 20 mA
V
Forward Voltage
VF
IF = 1.0 µA
V
Reverse Current
IR
VR = 5 V
Dominant Wavelength
Luminous Intensity
D-CT067.000
Data Sheet: CL
50% Power Angle
2
Minimum
Typical
Maximum
3.4
4.0
1.7
2.5
A
100
D
IF = 20 mA
nm
520
527
IV
IF = 20 mA
mcd
4180
7500
½H-H
IF = 20 mA
deg
Subject to change without notice.
www.cree.com/ledlamps
535
30
Standard Bins for LC503TPG1-30Q-A1 (IF = 20 mA)
Lamps are sorted to luminous intensity (IV) and dominant wavelength (
) bins shown.
D
Orders for LC503TPG1-30Q-A1 may be filled with any or all bins contained as below.
All luminous intensity (IV) and dominant wavelength (
Luminous Intensity (IV)
X7
) values shown and specified are at IF = 20 mA.
D
X8
X9
Z1 or
above
12000 mcd
Z
8200 mcd
Y
5860 mcd
X
4180 mcd
520 nm
525 nm
530 nm
Dominant Wavelength (
535 nm
)
D
Important Notes:
1. All ranks will be included per delivery; rank ratio will be based on the dice distribution.
2. Pb content <1000 ppm.
3. Tolerance of measurement of luminous intensity is ±15%.
4. Tolerance of measurement of dominant wavelength is ±1 nm.
5. Tolerance of measurement of VF is ±0.05 V.
6. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document.
7. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions.
8. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED
product safely.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
CLD-CT067.000
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
Document No. SPE/LC503TPG1-30P-A1
Rev. No.
02
Graphs
Graphs
100.0
-50
If (mA)
-40
-30
-10
-20
0
0.0
Vr(V)
-10.0
80.0
-20.0
60.0
-30.0
40.0
-40.0
20.0
0.0
3.0
3.4 3.8
4.2 4.6 5.0
FIG.1 FORWARD CURRENT VS.
FORWARD VOLTAGE.
-50.0
Ir(uA)
Vf(V)
FIG.2 REVERSE CURRENT VS.
REVERSE VOLTAGE.
Half Power WL=38nm
Domi WL= 525nm
I (RELATIVE LUMINOUS INTENSITY)
100%
5.0
4.0
75%
3.0
50%
2.0
25%
1.0
0%
300
If(mA)
0.0
0.0
20.0 40.0 60.0
80.0 100.0
FIG.3 RELATIVE LUMINOUS INTENSITY VS.
FORWARD CURRENT.
50
400
500
600
WL(nm)
800
700
FIG.4 RELATIVE LUMINOUS INTENSITY VS.
WAVELENGTH.
50% Power Angle : 30
IF(mA)
Ie(%)
0
100%
40
80%
30
60%
20
40%
10
0
20%
Ta( C)
0.0
20.0 40.0 60.0
0%
80.0 100.0
-90
FIG.5 MAXIMUM FORWARD DC CURRENT VS
AMBIENT TEMPERATURE (Tjmax=105 C)
tems
ared by
Signatures
Date
LiuZM
2006-03-31
-60
-30
0
oved by
CLD-CT067.000
David
2006-03-31
90
60
FIG.6 FAR FIELD PATTERN
Revision History
Rev. No
Date
Change Description
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
are registered trademarks
of Cree, Inc.
2006-03-31
cked byCree logo Aldosin
30
02
2006-03-31 Cancel VF bin.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
Mechanical Dimensions
Document No. SPE/LC503TPG1-30P-A1
Rev. No.
02
All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted.
An epoxy meniscus may extend
down
Dimabout
ensi1.5
onmm
Dra
winthe
g leads.
Burr around bottom of epoxy may be 0.5 mm max.
C
te maximum
Rating
Unit
25
mA
100
mA
5
V
100
mW
0 ~ +95
°C
0 ~ +100
°C
60°C for 3 sec Max.
the base
of the epoxy bulb)
Notes
RoHS Compliance
tics (
The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or
restricted
materials in this product are below the maximum concentration values (also referred to as the
)
Totherwise
a = 25°C
threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(RoHS), as amended through April 21, 2006.
Vision Advisory Claim
Condition
Min.
Typ.
Max.
Unit
Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye.
IF = 20mA
---
3.4
4.0
V
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks
IF = 1.0ȝA
1.7 of Cree, Inc.
CLD-CT067.000
---
2.5
V
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
Kit Number System
Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage,
and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED
Lamp Packaging Standard” document for more information about shipping and packaging options.
Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following
manner:
Standard/Custom
0: Standard
C: Custom
VF
0: Full forward voltage distribution
1~9, A~Z . . . : special request *
Wd/Color
1: Full-color distribution
2~9, A~Z . . . : special request *
aaaaaaaaa-aaa-aa- x x x x x
IV
0: Full luminous intensity distribution
1~9, A~Z . . . :special request *
Packing type
0: Standard = Bulk pack
1~9, A~Z . . . : special request *
Product P/N
* Contact your Cree sales representative for ordering information.
Standard Available Kits*
Kit Number
Description
LC503TPG1-30Q-A1-00001
5-mm Round 30 Pure-Green 527 nm, FULL RANK, Bulk Pack
LC503TPG1-30Q-A1-00002
5-mm Round 30 Pure-Green 527 nm, X8, X9, Bulk Pack
* Please contact your Cree representative about the availability of non-standard kits.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
CLD-CT067.000
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
Similar pages