PRELIMINARY CM2010 VGA Port Protection with Integrated Sync Buffers Features Product Description • The CM2010 connects between a video graphics controller, embedded in a PC or in a graphics adapter card, and the VGA port connector. The CM2010 integrates ESD protection for 3 VGA output signals implemented with low-capacitance current steering diodes such that an ESD pulse is diverted into either the positive supply rail or ground, where it may be safely dissipated. • • • • • 3 channels of ESD protection for RGB output pins meeting IEC-61000-4-2 Level 4 ESD requirements (8kV contact discharge) Very low loading capacitance from ESD protection diodes on VIDEO lines, 4pF typical 3.3/5V 24mA buffer drivers for HSYNC and VSYNC lines VESA Video Signal Standard (VSIS) - Version 1, Rev. 2 Compatible Outputs Compact 10-lead MSOP package Lead-free version available Two 24mA non-inverting drivers provide buffering for the HSYNC and VSYNC signals from the video controller IC (SYNC1, SYNC2). These buffers accept low voltage input levels and convert them to CMOS output levels that swing between Ground and VCC_SYNC, which is typically 5V for Legacy VESA compatibility, but can be operated at 3.3V. Additionally, the output impedance of the drivers can be discretely adjusted via external series termination resistors (RT) for maximum flexibility. The output impedance of the drivers can be adjusted over a wide range from 15Ω to over 100Ω. Applications • All ESD diodes are designed to safely handle the high current spikes specified by IEC61000-4-2 Level 4 ESD (8kV contact discharge). VGA and DVI-I ports in: - Desktop and Notebook PCs - Graphics Cards - Set Top Boxes The CM2010 is supplied in a 10-lead MSOP package and is available with optional lead-free finishing. Simplified Electrical Schematic VCC_VIDEO VCC_SYNC 2 1 3 4 5 GND VIDEO_1 VIDEO_2 VIDEO_3 SYNC_IN2 SYNC_IN1 9 10 7 8 SYNC_OUT2 SYNC_OUT1 6 © 2004 California Micro Devices Corp. All rights reserved. 09/10/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 1 PRELIMINARY CM2010 PACKAGE / PINOUT DIAGRAM TOP VIEW SYNC_OUT2 VCC_SYNC 1 10 VCC_VIDEO 2 9 SYNC_IN2 VIDEO_1 3 8 SYNC_OUT1 VIDEO_2 4 7 SYNC_IN1 VIDEO_3 5 6 GND 10-PIN MSOP Note: This drawing is not to scale. Ordering Information PART NUMBERING INFORMATION Standard Finish Lead-free Finish Pins Package Ordering Part Number1 Part Marking Ordering Part Number1 Part Marking 10 MSOP CM2010-02MS 2010 02MS CM2010-02MR 2010 02MR Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Pin Descriptions PIN DESCRIPTIONS LEAD(s) NAME 1 VCC_SYNC This is an isolated supply input for the SYNC_1 and SYNC_2 level shifters and their associated ESD protection circuits. 2 VCC_VIDEO This is a supply pin specifically for the VIDEO_1, VIDEO_2 and VIDEO_3 ESD protection circuits. 3 VIDEO_1 Video signal ESD protection channel. This pin is typically tied one of the video lines between the VGA controller device and the video connector. 4 VIDEO_2 Video signal ESD protection channel. This pin is typically tied one of the video lines between the VGA controller device and the video connector. 5 VIDEO_3 Video signal ESD protection channel. This pin is typically tied one of the video lines between the VGA controller device and the video connector. 6 GND 7 SYNC_IN1 8 SYNC_OUT1 9 SYNC_IN2 10 SYNC_OUT2 DESCRIPTION Ground reference supply pin. Sync signal buffer input. Connects to the VGA controller side of one of the sync lines. Sync signal buffer output. Connects to the video connector side of one of the sync lines. Sync signal buffer input. Connects to the VGA controller side of one of the sync lines. Sync signal buffer output. Connects to the video connector side of one of the sync lines. © 2004 California Micro Devices Corp. All rights reserved. 2 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 09/10/04 PRELIMINARY CM2010 Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING VCC_VIDEO and VCC_SYNC Supply Voltage Inputs UNITS 6.0 V 8 mA ESD Clamp Diode Forward DC Current (applies only to SYNC drivers) [GND - 0.5] to [VCC + 0.5] V Operating Temperature Range -40 to +85 °C Storage Temperature Range -40 to +150 °C DC Voltage at any channel Input ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE 1) SYMBOL ICC PARAMETER CONDITIONS MIN TYP MAX UNITS VCC Supply Current VCC_SYNC = 5V; SYNC inputs at GND or VCC_SYNC; SYNC outputs unloaded 50 µA VCC_SYNC = 5V; SYNC inputs at 3.0V; SYNC outputs unloaded 2.0 mA 1.0 V 0.5 V VF Diode Forward Voltage IF = 10mA VIH Logic High Input Voltage VCC_SYNC = 5.0V; Note 2 VIL Logic Low Input Voltage VCC_SYNC = 5.0V; Note 2 VOH Logic High Output Voltage IOH = 8mA, VCC_SYNC = 3.0V; Note 2 2.0 V IOH = 12mA, VCC_SYNC = 5.0V; Note 2 2.0 V IOH = 24mA, VCC_SYNC = 5.0V; Note 2 2.0 V VOL Logic Low Output Voltage ROUT IIN V IOL = 8mA, VCC_SYNC = 3.3V; Note 2 0.8 V IOL = 12mA, VCC_SYNC = 5.0V; Note 2 0.8 V IOL = 24mA, VCC_SYNC = 5.0V; Note 2 0.8 V Ω SYNC Driver Output Resistance VCC_SYNC = 5.0V; SYNC Inputs at GND or 3.0V Input Current VIDEO Inputs VCC_VIDEO = 5.0V; VIN = VCC_VIDEO or GND; TA=25°C ±1 µA VCC_SYNC = 5.0V; VIN = VCC_SYNC or GND; TA=25°C ±1 µA VCC_VIDEO = 5.0V; VIN = 2.5V; ƒ = 1MHz; Note 4 4.0 pF VCC_VIDEO = 2.5V; VIN = 1.25V; ƒ = 1MHz; Note 4 4.5 pF SYNC_IN1, SYNC_IN2 Inputs CIN_VID 1.5 VIDEO Input Capacitance 15 tPLH SYNC Driver L => H Propagation Delay CL = 10pF; VCC = 5.0V; Input tR and tF ≤ 5ns 12 ns tPHL SYNC Driver H => L Propagation Delay CL = 10pF; VCC = 5.0V; Input tR and tF ≤ 5ns 12 ns tR, tF SYNC Driver Output Rise & Fall Times CL = 10pF; VCC = 5.0V; Input tR and tF ≤ 5ns; Notes 2, 4 & 5 3 ns VESD ESD Withstand Voltage VCC_VIDEO = VCC_SYNC = 5V; Notes 3, 4 VCL ±8 Clamping Voltage during ESD Discharge Notes 3 and 4 MIL-STD-883 (Method 3015), 8kV Positive Transients Negative Transients kV +13 -13 V V Note 1: All parameters specified over standard operating conditions unless otherwise noted. Note 2: These parameters apply only to the SYNC drivers. Note 3: Per the IEC-61000-4-2 International ESD Standard, Level 4 contact discharge method. BYP, VCC must be bypassed to GND via a low impedance ground plane with a 0.22µF, low inductance, chip ceramic capacitor at each supply pin. ESD pulse is applied between the applicable pins and GND. ESD pulses can be positive or negative with respect to GND. Applicable pins are: VIDEO_1, VIDEO_2 and VIDEO_3. All other pins are ESD protected to the industry standard ±2kV Human Body Model (MIL-STD-883, Method 3015). Note 4: This parameter is guaranteed by design and characterization. Note 5: Rise and fall times measured between 0.5V and 2.4V. © 2004 California Micro Devices Corp. All rights reserved. 09/10/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 3 PRELIMINARY CM2010 Mechanical Details MSOP Mechanical Specifications: Mechanical Package Diagrams CM2010 devices are supplied in 10-pin MSOP packages. Dimensions are presented below. TOP VIEW For complete information on the MSOP-10 package, see the California Micro Devices MSOP Package Information document. D 10 9 8 6 7 PACKAGE DIMENSIONS Package MSOP Pins Dimensions 10 Millimeters Max Min Max A 0.75 0.95 0.028 0.038 A1 0.05 0.15 0.002 0.006 B 0.18 0.40 0.006 0.016 0.18 1 2 3 5 4 SIDE VIEW 0.007 D 2.90 3.10 0.114 0.122 E 2.90 3.10 0.114 0.122 e Pin 1 Marking Inches Min C E H 0.50 BSC 0.0196 BSC H 4.76 5.00 0.187 0.197 L 0.40 0.70 0.0137 0.029 # per tube 80 pieces* # per tape and reel 4000 A A1 SEATING PLANE B e END VIEW C Controlling dimension: inches L * This is an approximate number which may vary. Package Dimensions for MSOP-10 © 2004 California Micro Devices Corp. All rights reserved. 4 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 09/10/04