TA4303F TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic TA4303F Down Converter for BS/CS Tuner IC Description The TA4303F is a monolithic IC to down-convert the L-band (900~2150 MHz) signal for the satellite tuners. It's integrated circuits that perform the mixer/oscillator function. They have double-balanced mixer, local oscillator, IF amplifier, OSC buffer amplifier and prescaler buffer amplifier circuits. Features z Single chip full band solution, compatible with digital and analog transmissions. z Single 5 V power supply operation z Full band constant convertion Gain and Noise Figure z Local oscillator output circuit for PLL z Low Phase Noise local oscillator Weight: 0.17 g (typ.) 1 2007-11-01 TA4303F Pin Connection Function Block Diagram Marking Caution This devices is electrostatic sensitivity. 2 2007-11-01 TA4303F Explanation Pin No. Pin Name Pin Voltage 0 Explanation 1 GND (IF Amp) 2 IF out 2.2 IF output pin. 3 VCC1 (MIX + IF Amp) 5.0 Supply voltage for MIX + IF Amp. 4 RFin-1 1.7 RF input pin. 5 RFin-2 1.7 RF input pin. 6 NC ― ― ― 7 NC ― ― ― 8 NC ― ― ― 9 NC ― ― ― 10 NC ― ― ― 11 GND (MIX) 0 GND pin for MIX. 12 VCOout 2.0 OSC output pin. 13 VCC2 (OSC Buff + PSC Buff) 5.0 Supply voltage pin for OSC Buff + PSC Buff. ― 14 GND (PSC Buff) GND pin for PSC Buff. ― 15 OSC-c 5.0 OSC collector pin, supply voltage pin. 16 OSC-e 1.8 Emitter pin for OSC. 17 OSC-b 2.6 Base pin for OSC. 0 GND pin for IF Amp. Equivalent Circuit ― ― ― 3 2007-11-01 TA4303F Pin No. Pin Name Pin Voltage 18 GND (OSC) 0 19 RF GND (OSC Buff) 1.4 20 GND (OSC Buff) 0 Explanation GND pin for OSC. Equivalent Circuit ― RF GND pin. GND pin for OSC Buff. 4 ― 2007-11-01 TA4303F Absolute Maximum Ratings (Ta = 25°C) Characteristic Supply voltage Total power dissipation Symbol Rating Unit VCC 6 V 1100 mW PD (Note 1) Operating temperature Topr −20~85 °C Storage temperature Tstg −45~150 °C Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: 100 cm2 × 1.6 t (Cu layer area: 36%) on glass epoxy resins. Operating Ranges Characteristic Symbol Rating Unit Supply voltage VCC (Amp) 4.75~5.25 V Supply voltage VCC (OSC) 4.75~5.25 V Input frequency range fin 900~2150 MHz IF Input frequency range fIF 350~550 MHz Electrical Characteristics (Ta = 25°C) (Note 2) Characteristics Supply current Symbol Test Circuit ICC (Total) 1 Test Condition Min Typ. Max Unit VCC = 5 V, No RF input 61 74 87 mA Conversion gain Gc 1 fin = 1.6 GHz, fIF = 400 MHz 14 18 25 dB Noise figure NF 1 fin = 1.6 GHz, fIF = 400 MHz ― 15 22 dB PO (sat) 1 fin = 1.6 GHz, fIF = 400 MHz 5 10 ― dBmW IP3 1 fin = 1.596 GHz, 1.6 GHz fIF = 400 MHz, 404 MHz 12 17 24 dBmW POSC 1 fLO = 2.0 GHz −14 −8 ― dBmW Saturation output Third-order intercept Posc Note 2: All electrical characteristics measured in Supply Voltage 5.0 V (Amp, OSC, OSC Buffer) Reference Characteristic (Note 3) Symbol Test Circuit Supply current ICC (Amp) 1 Supply current ICC (OSC) 1 Characteristics Test Condition Typ. Unit VCC = 5 V, No RF input 36 mA VCC = 5 V, No RF input 38 mA Note 3: All electrical characteristics measured in Supply Voltage 5.0 V (Amp, OSC, OSC Buffer) 5 2007-11-01 TA4303F Test Circuit Notice The circuits and measurements contained in this document are given only in the context of as examples of applications for these products. Moreover, these example application circuits are not intended for mass production, since the high-frequency characteristics (the AC characteristics) of these devices will be affected by the external components which the customer uses, by the design of the circuit and by various other conditions. It is the responsibility of the customer to design external circuits which correctly implement the intended application, and to check the characteristics of the design. TOSHIBA assume no responsibility for the integrity of customer circuit designs or applications. 6 2007-11-01 TA4303F 7 2007-11-01 TA4303F 8 2007-11-01 TA4303F Package Dimensions 9 2007-11-01 TA4303F RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 10 2007-11-01