Fairchild FSDM311 Green mode fairchild power switch (fps tm) Datasheet

FSDM311
Green Mode Fairchild Power Switch (FPS™)
Features
Description
ƒ Internal Avalanche Rugged SenseFET
ƒ Precision Fixed Operating Frequency (67KHz)
ƒ Advanced Burst-Mode Operation (power consumption
The FSDM311, consisting of integrated Pulse-Width
Modulator (PWM) and SenseFET, is specifically
designed for high-performance, off-line Switch Mode
Power Supplies (SMPS) with minimal external
components. This device is an integrated high-voltage,
power-switching regulator which combines a VDMOS
SenseFET with a voltage mode PWM control block. The
integrated PWM controller features include: a fixed
oscillator, Under-Voltage Lockout (UVLO) protection,
Leading Edge Blanking (LEB), an optimized gate turnon/turn-off driver, Thermal Shutdown (TSD) protection,
and
temperature-compensated,
precision-current
sources for loop-compensation and fault-protection
circuitry. When compared to a discrete MOSFET and
controller or RCC switching converter solution, the
FSDM311 device reduces total component count and
design size and weight; while increasing efficiency,
productivity, and system reliability. This device provides
a basic platform that is well suited for the design of costeffective flyback converters.
< 0.1W at 265VAC, no-load condition)
ƒ Internal Start-up Circuit
ƒ Pulse-by-Pulse Current Limit
ƒ Over-Voltage Protection (OVP)
ƒ Over-Load Protection (OLP)
ƒ Internal Thermal Shutdown Function (TSD)
ƒ Auto-Restart Mode
ƒ Under-Voltage Lockout (UVLO) with Hysteresis
ƒ Built-in Soft-Start
Applications
ƒ Charger & Adapter for Mobile Phone, PDA & MP3
ƒ Auxiliary Power for White Goods, PC, C-TV & Monitor
Related Application Notes
ƒ AN-4137, AN-4141, AN-4147 (Flyback)
ƒ AN-4134 (Forward)
ƒ AN-4138 (Charger)
Ordering Information
Product Number
Package
Marking Code
BVDSS
fOSC
RDS (ON)
FSDM311
8DIP
DM311
650V
67KHz
14Ω
FSDM311L
8LSOP
DM311
650V
67KHz
14Ω
FPS™ is a trademark of Fairchild Semiconductor Corporation.
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
www.fairchildsemi.com
FSDM311 Green Mode Fairchild Power Switch (FPS™)
July 2006
OUTPUT POWER TABLE
Product
Open Frame(1)
230VAC±15%(2)
85~265VAC
FSDM311
13W
8W
FSDM311L
13W
8W
Notes:
1. Maximum practical continuous power in open-frame
design with sufficient drain pattern as a heat sink,
at 50°C ambient.
2. 230VAC or 100/115VAC with doubler.
Figure 1 Typical Flyback Application
Internal Block Diagram
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Typical Application & Output Power Table
Figure 2 Functional Block Diagram of FSDM311
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
2
www.fairchildsemi.com
Figure 3 Pin Configuration (Top View)
Pin Definitions
Pin Number
Pin Name
1
GND
2
VCC
3
Vfb
4
NC
5
Vstr
6,7,8
Drain
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
Pin Function Description
Ground. SenseFET source terminal on primary side and internal control
ground.
Positive supply voltage input. Although connected to an auxiliary
transformer winding, current is supplied from pin 5 (Vstr) via an internal switch
during start-up (see Internal Block Diagram section). When VCC reaches the
UVLO upper threshold (9V), the internal start-up switch opens and device
power is supplied by the auxiliary transformer winding.
Feedback. Inverting input to the PWM comparator with its normal input level
between 0.5V and 2.5V. It has a 0.4mA current source connected internally,
while a capacitor and opto-coupler are typically connected externally. A
feedback voltage of 4.5V triggers overload protection (OLP). There is a time
delay while charging the external capacitor Cfb from 3V to 4.5V using an
internal 5μA current source. This time delay prevents false triggering under
transient conditions, but allows the protection mechanism to operate under true
overload conditions.
No Connection.
Start-up. This pin connects directly to the rectified AC line voltage source. At
start-up, the internal switch supplies internal bias and charges an external
storage capacitor placed between the VCC pin and ground. Once the VCC
reaches 9V, the internal switch stops charging the capacitor.
SenseFET Drain. The drain pins are designed to connect directly to the
primary lead of the transformer and are capable of switching a maximum of
650V. Minimizing the length of the trace connecting these pins to the
transformer is recommended to decrease leakage inductance.
3
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Pin Assignments
www.fairchildsemi.com
The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The
device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables
are not guaranteed at the absolute maximum ratings.
TA=25°C, unless otherwise specified.
Symbol
VDRAIN
VSTR
VDG
VGS
IDM
ID
ID
EAS
VCC
VFB
PD
TJ
TA
TSTG
Parameter
Drain Pin Voltage
Vstr Pin Voltage
Drain-Gate Voltage
Gate-Source Voltage
Drain Current Pulsed(3)
Continuous Drain Current (Tc=25°C)
Continuous Drain Current (Tc=100°C)
Single Pulsed Avalanche Energy(4)
Supply Voltage
Feedback Voltage Range
Total Power Dissipation
Operating Junction Temperature
Operating Ambient Temperature
Storage Temperature
Value
Unit
650
650
650
±20
1.5
0.5
0.32
10
20
-0.3 to VSTOP
1.40
Internally limited
-25 to +85
-55 to +150
V
V
V
V
A
A
A
mJ
V
V
W
°C
°C
°C
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Absolute Maximum Ratings
Notes:
3. Repetitive rating: Pulse width is limited by maximum junction temperature.
4. L = 24mH, starting TJ = 25°C.
Thermal Impedance
FSDM311 8DIP. TA=25°C, unless otherwise specified.
Symbol
Parameter
(5)
Value
Unit
θJA
Junction-to-Ambient Thermal Impedance
88.84
°C/W
θJC
Junction-to-Case Thermal Impedance(6)
13.94
°C/W
Notes:
5. Free standing with no heat sink, without copper clad. (Measurement Condition – Just before junction temperature
TJ enters into OTP.)
6. Measured on the DRAIN pin close to plastic interface.
All items are tested with the standards JESD 51-2 and 51-10 (DIP).
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
4
www.fairchildsemi.com
TA=25°C, unless otherwise specified.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
-
-
25
-
-
200
1.0
-
14
1.3
162
18
3.8
9.5
19
33
42
7.0
3.1
0.4
19
-
61
60
8
6
0.35
10
4.2
67
±5
67
9
7
0.40
15
4.5
73
±10
74
10
8
0.45
20
4.8
KHz
%
%
V
V
mA
ms
V
-
0.3
0.6
mV/°C
Hysteresis
0.6
0.45
-
0.7
0.55
150
0.8
0.65
-
V
V
mV
0.55
145
4.5
5
0.625
5.0
6
A
°C
V
V
3V ≤ VFB ≤ VSD
0.475
125
4.0
20
4
μA
-
1.5
3.0
mA
450
550
650
μA
SenseFET SECTION
IDSS
Zero-Gate-Voltage Drain Current
RDS(ON)
Drain-Source On-State Resistance(7)
gfs
Forward Trans-Conductance
CISS
Input Capacitance
COSS
Output Capacitance
CRSS
Reverse Transfer Capacitance
td(on)
Turn-On Delay Time
tr
Rise Time
td(off)
Turn-Off Delay Time
tf
Fall Time
Qg
Total Gate Charge
Qgs
Gate-Source Charge
Qgd
Gate-Drain (Miller) Charge
CONTROL SECTION
fOSC
Switching Frequency
ΔfOSC
Switching Frequency Variation(8)
DMAX
Maximum Duty Cycle
VSTART
UVLO Threshold Voltage
VSTOP
IFB
Feedback Source Current
tS/S
Internal Soft-Start Time
VREF
Reference Voltage(9)
Reference Voltage Variation with
ΔVREF/ΔT
Temperature(8)(9)
BURST-MODE SECTION
VBURH
Burst-Mode Voltage
VBURL
VBUR(HYS)
PROTECTION SECTION
ILIM
Peak Current Limit
TSD
Thermal Shutdown Temperature(9)
VSD
Shutdown Feedback Voltage
VOVP
Over-Voltage Protection
IDELAY
Shutdown Delay Current
TOTAL DEVICE SECTION
IOP
Operating Supply Current (control part only)
ICH
Start-Up Charging Current
VDS=650V, VGS=0V
VDS=520V, VGS=0V,
TC=125°C
VGS=10V, ID=0.5A
VDS=50V, ID=0.5A
VGS=0V, VDS=25V,
f=1MHz
VDS=325V, ID=1.0A
VGS=10V, ID=1.0A,
VDS=325V
-25°C ≤ TA ≤ 85°C
VFB=GND
VFB=GND
0V ≤ VFB ≤ 3V
-25°C ≤ TA ≤ 85°C
TJ=25°C
VCC ≤ 16V
VCC=0V , VSTR=50V
μA
Ω
S
pF
ns
nC
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Electrical Characteristics
Notes:
7. Pulse test: Pulse width ≤ 300μs, duty ≤ 2%.
8. These parameters, although guaranteed, are tested in EDS (wafer test) process.
9. These parameters, although guaranteed, are not 100% tested in production.
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
5
www.fairchildsemi.com
1.15
1.15
1.10
1.10
1.05
1.05
1.00
1.00
IOP
Vref
These characteristic graphs are normalized at TA = 25°C.
0.95
0.95
0.90
0.90
0.85
-50
0
50
100
0.85
150
-50
0
1.15
1.15
1.10
1.10
1.05
1.05
1.00
0.95
0.90
0.90
0
50
100
0.85
150
-50
0
Temperature [°C]
1.10
1.10
1.05
1.05
DMAX
fOSC
1.15
1.00
0.95
0.90
0.90
50
100
0.85
150
-50
0
50
100
150
Temperature [°C]
Temperature [°C]
Figure 8. Operating Frequency (fOSC) vs. TA
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
150
1.00
0.95
0
100
Figure 7. Stop Threshold Voltage (VSTOP) vs. TA
1.15
-50
50
Temperature [°C]
Figure 6. Start Threshold Voltage (VSTART) vs. TA
0.85
150
1.00
0.95
-50
100
Figure 5. Operating Supply Current (IOP) vs. TA
VSTOP
VSTAART
Figure 4 Reference Voltage (VREF) vs. TA
0.85
50
Temperature [°C]
Temperature [°C]
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Temperature Characteristics
Figure 9. Maximum Duty Cycle (DMAX) vs. TA
6
www.fairchildsemi.com
1.15
1.10
1.10
1.05
1.05
1.00
1.00
IFB
ILIM
1.15
0.95
0.95
0.90
0.90
0.85
-50
0
50
100
0.85
150
-50
0
Temperature [°C]
1.15
1.15
1.10
1.10
1.05
1.05
1.00
0.95
0.90
0.90
0
50
150
1.00
0.95
-50
100
Figure 11. Feedback Source Current (IFB) vs. TA
VSD
IDELAY
Figure 10. Peak Current Limit (ILIM) vs. TA
0.85
50
Temperature [°C]
100
0.85
150
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Temperature Characteristics (continued)
-50
0
50
100
150
Temperature [°C]
Temperature [°C]
Figure 12. Shutdown Delay Current (IDELAY) vs. TA
Figure 13. Shutdown Feedback Voltage (VSD) vs. TA
1.15
1.10
VOVP
1.05
1.00
0.95
0.90
0.85
-50
0
50
100
150
Temperature [°C]
Figure 14. Over-Voltage Protection (VOVP) vs. TA
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
7
www.fairchildsemi.com
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Functional Description
1. Start-up: At start-up, the internal high-voltage current
source supplies the internal bias and charges the
external Vcc capacitor, as shown in Figure 15. In the
case of the FSDM311, when Vcc reaches 9V, the device
starts switching and the internal high-voltage current
source stops charging the capacitor. The device is in
normal operation provided that Vcc does not drop below
7V. After start-up, the bias is supplied from the auxiliary
transformer winding.
Figure 15. Internal Startup Circuit
Calculating the Vcc capacitor is an important step in
design with the FSDM311. At initial start-up in the
FSDM311, the maximum value of start operating current
ISTART is about 100μA, which supplies current to UVLO
and Vref Blocks. The charging current IVcc of the Vcc
capacitor is equal to ISTR - ISTART. After VCC reaches the
UVLO start voltage, only the bias winding supplies Vcc
current to the device. When the bias winding voltage is
not sufficient, the Vcc level decreases to the UVLO stop
voltage and the internal current source is activated
again to charge the Vcc capacitor. To prevent this Vcc
fluctuation (charging/discharging), a Vcc with a value
between 10uF and 47μF should be chosen.
Figure 16. Charging Vcc Capacitor Through Vstr
2. Feedback Control: The FSDM311 is a voltage-mode
controlled device, as shown in Figure 17. Usually, an
opto-coupler with shunt regulator, like KA431, is used to
implement the feedback network. The feedback voltage
is compared with an internally generated sawtooth
waveform, which directly controls the duty cycle. When
the KA431 reference pin voltage exceeds the internal
reference voltage of 2.5V, the opto-coupler LED current
increases, the feedback voltage Vfb is pulled down, and
it reduces the duty cycle. This happens when the input
voltage increases or the output load decreases.
Figure 17. PWM and Feedback Circuit
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
8
www.fairchildsemi.com
4. Protection Circuit: The FSDM311 has several
protective functions, such as overload protection (OLP),
over-voltage protection (OVP), under-voltage lockout
(UVLO), and thermal shutdown (TSD). Because these
protection circuits are fully integrated in the IC without
external components, the reliability is improved without
increasing cost. Once a fault condition occurs, switching
is terminated and the SenseFET remains off. This
causes Vcc to fall. When Vcc reaches the UVLO stop
voltage VSTOP (7V), the protection is reset and the
internal high-voltage current source charges the Vcc
capacitor via the Vstr pin. When Vcc reaches the UVLO
start voltage VSTART (9V), the device resumes normal
operation. In this manner, the auto-restart can
alternately enable and disable the switching of the
power SenseFET until the fault condition is eliminated.
t1 2 = C F B
V ( t 2 ) - V ( t1 )
;
ID E L A Y
I D E L A Y = 5 μ A , V ( t1 ) = 3V , V ( t 2 ) = 4 .5V
Figure 19. Overload Protection (OLP)
FSDM311 Green Mode Fairchild Power Switch (FPS™)
increases until it reaches 4.5V, when the switching
operation is terminated, as shown in Figure 19. The
shutdown delay time is the time required to charge Cfb
from 3V to 4.5V with a 5μA current source.
3. Leading Edge Blanking (LEB): At the instant the
internal SenseFET is turned on, the primary-side
capacitance and secondary-side rectifier diode reverse
recovery typically cause a high current spike through the
SenseFET. Excessive voltage across the Rsense resistor
leads to incorrect pulse-by-pulse current limit protection.
To avoid this, a leading edge blanking (LEB) circuit
disables pulse-by-pulse current limit protection block for
a fixed time (tLEB) after the SenseFET turns on.
4.2 Thermal Shutdown (TSD): The SenseFET and the
control IC are integrated, making it easier for the control
IC to detect the temperature of the SenseFET. When
the temperature exceeds approximately 145°C, thermal
shutdown is activated.
5. Soft-Start: The FPS has an internal soft-start circuit
that slowly increases the feedback voltage, together with
the SenseFET current, right after it starts up. The typical
soft-start time is 15ms, as shown in Figure 20, where
progressive increment of the SenseFET current is
allowed during the start-up phase. The soft-start circuit
progressively increases current limits to establish proper
working conditions for transformers, inductors,
capacitors, and switching devices. It also helps to
prevent transformer saturation and reduces the stress
on the secondary diode.
Figure 18. Protection Block
4.1 Overload Protection (OLP): Overload is defined as
the load current exceeding a pre-set level due to an
unexpected event. In this situation, the protection circuit
should be activated to protect the SMPS. However,
even when the SMPS is operating normally, the
overload protection (OLP) circuit can be activated during
the load transition. To avoid this undesired operation,
the OLP circuit is designed to be activated after a
specified time to determine whether it is a transient
situation or true overload situation. If the output
consumes more than the maximum power determined
by ILIM, the output voltage (Vo) decreases below its rating
voltage. This reduces the current through the optocoupler LED, which also reduces the opto-coupler
transistor current, thus increasing the feedback voltage
(VFB). If VFB exceeds 3V, the feedback input diode is
blocked and the 5μA current source (IDELAY) starts to
charge Cfb slowly up to Vcc. In this condition, VFB
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
Figure 20. Internal Soft-Start
9
www.fairchildsemi.com
FSDM311 Green Mode Fairchild Power Switch (FPS™)
6. Burst Operation: To minimize the power dissipation
in standby mode, the FSDM311 enters burst--mode
operation. As the load decreases, the feedback voltage
decreases. The device automatically enters burst mode
when the feedback voltage drops below VBURL(0.55V). At
this point, switching stops and the output voltages start
to drop. This causes the feedback voltage to rise. Once
it passes VBURH (0.70V), switching starts again. The
feedback voltage falls and the process repeats. Burstmode operation alternately enables and disables
switching of the power MOSFET to reduce the switching
loss in the standby mode.
Figure 21. Burst Operation Block
Figure 22. Burst Operation Function
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
10
www.fairchildsemi.com
Methods of Reducing Audible Noise
Switching mode power converters have electronic and
magnetic components, which generate audible noises
when the operating frequency is in the range of
20~20,000Hz. Even though they operate above 20KHz,
they can make noise in some load conditions. Designers
can employ several methods to reduce noise, including:
Glue or Varnish
The most common method involves using glue or
varnish to tighten magnetic components. The motion of
core, bobbin, and coil; and the chattering or
magnetostriction of core, can cause the transformer to
produce audible noise. The use of rigid glue and varnish
helps reduce the transformer noise, but can crack the
core because sudden changes in the ambient
temperature cause the core and the glue to expand or
shrink at different rates.
Figure 23. Equal Loudness Curves
Ceramic Capacitor
Using a film capacitor instead of a ceramic capacitor as
a snubber is another noise reduction solution. Some
dielectric materials show a piezoelectric effect,
depending on the electric field intensity. Hence, a
snubber capacitor becomes one of the most significant
sources of audible noise. It is possible to use a Zener
clamp circuit instead of an RCD snubber for higher
efficiency as well as lower audible noise.
Figure24. Typical Feedback Network of FPS
Other Reference Materials
AN-4134: Design Guidelines for Off-line Forward
Converters Using Fairchild Power Switch (FPS™)
Adjusting Sound Frequency
Moving the fundamental frequency of noise out of the
2~4KHz range is the third method. Generally, humans
are more sensitive to noise in the range of 2~4KHz.
When the fundamental frequency of noise is located in
this range, the noise is perceived as louder, although
the noise intensity level is identical. Refer to Figure 23
for equal loudness curves.
AN-4137: Design Guidelines for Off-line Flyback
Converters Using Fairchild Power Switch (FPS™)
AN-4138: Design Considerations for Battery Charger
Using Green Mode Fairchild Power Switch (FPS™)
AN-4140: Transformer Design Consideration for Off-line
Flyback Converters Using Fairchild Power Switch
(FPS™)
When FPS acts in burst mode and the burst operation is
suspected to be a source of noise, this method may be
helpful. If the frequency of burst mode operation lies in
the range of 2~4KHz, adjusting the feedback loop can
shift the burst operation frequency. To reduce the burst
operation frequency, increase a feedback gain capacitor
(CF), opto-coupler supply resistor (RD), and feedback
capacitor (CB); and decrease a feedback gain resistor
(RF), as shown in Figure 24.
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Application Tips
AN-4141: Troubleshooting and Design Tips for Fairchild
Power Switch (FPS™) Flyback Applications
AN-4147: Design Guidelines for RCD Snubber of
Flyback
AN-4148: Audible Noise Reduction Techniques for
Fairchild Power Switch (FPS™) Applications
11
www.fairchildsemi.com
Application
Output Power
Input Voltage
12.5W
DC 275~375V
10W
DC 120~375V
PC Standby Power
(Demo board)
Output Voltage (Max. Current)
5.1V (2.5A, isolated)
15V (20mA, non-isolated)
5.1V (2.0A, isolated)
15V (20mA, non-isolated)
Features
ƒ Auxiliary Power for PC Power Supply with Passive PFC
DC Input Voltage 275V ~ 375V (Voltage Doubler) for 12.5W Output
DC Input Voltage 120V ~ 375V (Off-Line Universal Input) for 10W Output
ƒ Isolated Secondary Output 5.1V / 2.5A (max), 3.5A (peak) @VIN=275~375VDC
Isolated Secondary Output 5.1V / 2.0A (max), 2.5A (peak) @VIN =120~375VDC
ƒ Non-Isolated Aux-Output 15V(13~17V) / 10mA (up to 20mA)
ƒ Regulation 5.1V ±2.5% - Accuracy depends on Reference (e.g. shunt regulator or precision resistors)
ƒ Low No-Load Power Consumption:
< 100mW @ All Input Voltage
< 820mW @ All Input Voltage, 0.5W Output
ƒ High Efficiency:
> 80% @ 375Vdc Input, 12.5W Output
> 79% @ 160Vdc Input, 10W Output
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Typical Application Example
Schematic
Note:
The selection of aux-winding diode D2 affects Aux-Output (Vcc) regulation. If another component should be used, its
validity must be verified experimentally.
Figure 25. Schematic of FSDM311 PC Standby Power
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
12
www.fairchildsemi.com
TOP
BOTTOM
(pin side)
Figure 26. Transformer Construction Diagram
3~4mm
3~4mm
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Transformer Construction
Return
Wire
Insulation Tape
R
<
Wire (W5v or Wcc)
Core
Figure 27. Winding Direction for Each Winding (Left) and
Cross-Sectional View for W5v / Wcc Insulation Taping (Right)
Figure 28. Details on W5v / Wcc Insulation Taping
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
13
www.fairchildsemi.com
All windings should be wound tightly and evenly across the bobbin.
Winding
Pin(S → F)
Wire (φ:mm)
Turns
Winding Method
(10)
Top
Insulation: Polyester Tape t = 0.025mm, 2 Layers
f2 → 1
Wp4
0.22φ ×1
53
Solenoid winding
(10)
Insulation: Polyester Tape t = 0.025mm, 1 Layers
Wp3
2 → f2
0.22φ ×1
53
Solenoid winding
(11)
Insulation: Polyester Tape t = 0.025mm, 2 Layers
W5v
7,8,9 → 11,12
0.55φ ×2
12
Bifilar Solenoid winding
Insulation: Polyester Tape t = 0.025mm, 2 Layers(11)
Wcc
5→6
0.35φ ×1
34
Solenoid winding
Insulation: Polyester Tape t = 0.025mm, 1 Layers(10)
Wp2
f1 → 2
0.22φ ×1
53
Solenoid winding
(10)
Insulation: Polyester Tape t = 0.025mm, 1 Layers
Bottom
Wp1
3 → f1
0.22φ ×1
53
Solenoid winding
Notes:
10. Overlapped section length between the start and the end of insulation tape is about 3mm – see Figure 29.
11. See Figure 27 (right) and Figure 28 for details.
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Winding Specification
Figure 29. Overlapped Section of Insulation Taping
Electrical Characteristics
Pin
Specification
Remark
Magnetizing Inductance (Lm)
1–3
2.3mH (typical)
(2.2mH < Lm ≤ 2.4mH)
Leakage Inductance
1–3
< 35μH
67KHz, 1 V
All other pins open
67KHz, 1V
All other pins shorted
First Resonant Frequency
1–3
> 630KHz
All other pins open
Core & Bobbin
ƒ Core: EE1927S (SAMWHA Electronics, PL7 / Ae = 23.4mm2)
ƒ Bobbin: Vertical, 12 pins, 6 pins at each side, 20mm width (bobbin wall to wall)
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
14
www.fairchildsemi.com
Item
Qty.
Reference
Value
1
1
CS1
1.5nF 50V
2
1
CY1
1nF AC250V
3
1
C1
10nF 1KV
4
1
C2
1nF 1KV
Description
MLCC X7R, ±10% Tolerance SMD 0805
Y1 Safety Capacitor
Ceramic
Ceramic
Low ESR (40mΩ) Electrolytic
(e.g. Samwha Electric WB series)
Low ESR (70mΩ) Electrolytic
(e.g. Samwha Electric WB series)
5
2
C3, C4
1000µF 10V
6
1
C5
470µF 10V
7
1
C6
47nF 50V
8
1
C7
150nF 50V
Ceramic X7R, ±5% Tolerance
9
2
C8, C9
47μF 25V
Electrolytic
10
2
D1, D2
1N4007
1A, 1000V Diode (Fairchild Semiconductor)
Ceramic X7R, ±5% Tolerance
11
1
D3
SB540
5A, 40V Schottky Diode
12
1
D4
1N4148
200mA, 100V Fast Switching Diode (Fairchild Semiconductor)
13
1
J1
(Wire)
14
1
L1
1μH
3.5A Inductor
15
1
RS1
10Ω
Resistor 1/4W SMD 1206
16
1
R1
10Ω
Resistor 1/4W
17
1
R2
1Ω
(R3)
Jumper (Test Point)
Resistor 1/4W
Option for V2 Voltage Clamping
18
1
R4
6.2kΩ 2%
2% Precision Resistor 1/4W
19
1
R5
6kΩ 2%
2% Precision Resistor 1/4W
20
1
R6
20kΩ
Resistor 1/4W
21
1
R7
200Ω
Resistor 1/4W
22
1
R8
680Ω
Resistor 1/4W
23
1
T1
EE1927S
Transformer (Core: EE1927S Samwha Electronics)
24
1
U1
FSDM311
Fairchild Power Switch (Fairchild Semiconductor FPS)
25
1
U2
H11A817B
Opto-coupler (Fairchild Semiconductor)
26
1
U3
KA431A
27
1
ZD1
P6KE180A
28
1
ZD2
1N4763A
Shunt Regulator (Fairchild Semiconductor)
180V TVS
91V 1W Zener Diode
(ZD3)
Option for V2 Voltage Clamping
(ZD4)
Option for Protecting VFB Pin
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Circuit Part List
15
www.fairchildsemi.com
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Layout Information
Single layer, size 59 x 40mm
Figure 30. PCB Layout – Top- Side Print (Top) and Bottom-Side Print (Bottom)
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
16
www.fairchildsemi.com
8-DIP
Dimensions are in millimeters (inches) unless otherwise noted.
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
17
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Physical Dimensions
www.fairchildsemi.com
8-LSOP
Dimensions are in millimeters (inches) unless otherwise noted.
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
18
FSDM311 Green Mode Fairchild Power Switch (FPS™)
Physical Dimensions (Continued)
www.fairchildsemi.com
ACEx™
ActiveArray™
Bottomless™
Build it Now™
CoolFET™
CROSSVOLT™
DOME™
EcoSPARK™
2
E CMOS™
EnSigna™
FACT™
FACT Quiet Series™
®
FAST
FASTr™
FPS™
FRFET™
GlobalOptoisolator™
GTO™
HiSeC™
2
I C™
i-Lo™
ImpliedDisconnect™
IntelliMAX™
ISOPLANAR™
LittleFET™
MICROCOUPLER™
MicroFET™
MicroPak™
MICROWIRE™
MSX™
MSXPro™
OCX™
OCXPro™
®
OPTOLOGIC
OPTOPLANAR™
PACMAN™
POP™
Power247™
PowerEdge™
PowerSaver™
®
PowerTrench
®
QFET
QS™
QT Optoelectronics™
Quiet Series™
RapidConfigure™
RapidConnect™
ScalarPump™
μSerDes™
®
SILENT SWITCHER
SMART START™
SPM™
Stealth™
SuperFET™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SyncFET™
TCM™
TinyBoost™
TinyBuck™
®
TinyLogic
TINYOPTO™
TinyPower™
TinyPWM™
TruTranslation™
UHC™
®
UltraFET
UniFET™
VCX™
Wire™
Across the board. Around the world.™
Programmable Active Droop™
®
The Power Franchise
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS
HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF
THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE
UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF
FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE
PRODUCTS.
FSDM311 Green Mode Fairchild Power Switch (FPS™)
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an
exhaustive list of all such trademarks.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1.
Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body or (b) support or sustain life, and (c)
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury of the user.
2.
A critical component in any component of a life
support, device, or system whose failure to
perform can be reasonably expected to cause the
failure of the life support device or system, or to
affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Advance Information
Formative or In Design
This datasheet contains the design specifications for product development.
Specifications may change in any manner without notice.
Definition
Preliminary
First Production
This datasheet contains preliminary data; supplementary data will be
published at a later date. Fairchild Semiconductor reserves the right to make
changes at any time without notice to improve design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild Semiconductor
reserves the right to make changes at any time without notice to improve
design.
Obsolete
Not In Production
This datasheet contains specifications on a product that has been
discontinued by Fairchild Semiconductor. The datasheet is printed for
reference information only.
Rev. I20
© 2003 Fairchild Semiconductor Corporation
FSDM311 Rev. 1.1.0 • 7/14/06
19
www.fairchildsemi.com