OX-4033-EAE-1080-20M00 OCXO Preliminary version: Subject to technical modification. Nominal frequency (f0) 20 MHz Frequency stabilities Parameter Frequency stability Operating temp. range Over all (df/f0) -4.6 to 4.6 ppm vs. operating temp. range (df/f@25 °C) -10 to 10 ppb Additional information Drift 24 Hr and ±2.8°C temp. change < ±1ppb over all include: Temp Stab, supply, load stab, inital, 20 years aging S3E compliant according GR1244 Parameter -40 ... 85 °C Value Condition -500 to 500 ppb -10 to 10 ppb -10 to 10 ppb <± 1 ppb <± 25 ppb <± 100 ppb <± 1 ppm ± 10 ppb @25 °C static; 3.3 V ±5 % static; Load ± 5 % after 30 days ; @ 25 °C after 30 days ; @ 25 °C after 30 days ; @ 25 °C after 30 days ; @ 25 °C incl. Drift and -40...85°C temperature stability Parameter Value Condition Signal Load Fan out Rise Time Fall Time Duty cycle V Low V High LVCMOS 15 pF ±10 % 3 < 10 ns < 10 ns 45 / 55 % x < 0.4 V x > 2.4 V initial tolerance (df/f0) vs. supply voltage change (df/f) vs. load change (df/f) vs. aging / daily (df/f) vs. aging / month (df/f) vs. aging / year (df/f) vs. aging / 10 years (df/f) Holdover 24 h RF output @ 10 to 90 %Vout @ 90 to 10 %Vout @ 1.65 V Supply voltage Parameter Supply voltage (Vs) Current consumption steady state Current consumption during warm up Value Condition 3.3 V ± 5 % < 330 mA < 757 mA @ Vsnom & 25 °C @ Vs Additional Parameters Parameter Phase Noise MTIE Parameter Typ. Max. Condition -85 -110 -130 -143 -150 0.5 ns 3 ns 5 ns 20 ns 30 ns -60 -90 -115 -130 -145 dBc/Hz@1Hz dBc/Hz@10Hz dBc/Hz@100Hz dBc/Hz@1kHz dBc/Hz@10kHz 1 sec 10 sec 100 sec 1000 sec 10000 sec Value Jitter < 1.00 psec (RMS) TDEV 0.015 ns TDEV 0.12 ns TDEV 0.5 ns TDEV 2 ns Warm-up time < 3 min Additional information TDEV:Typical Wander Generation performance when locked through a 1mHz system loop bandwidth Holdover 10ppb peak-peak: incl. of 24 h aging and a 40°C temperature change Processing & Packing handling&processing note Vectron International • Product Specifications OX-4033-EAE-1080 www.vectron.com Condition @ 12 kHz to 20 Hz 1s 10 s 100 s 1000 s @ 25 °C to final frequency 20-May-10 by Göhrig, Detlef Index : P3 printed 2011-05-10 • page 1 of 5 OX-4033-EAE-1080-20M00 OCXO Preliminary version: Subject to technical modification. Additional environmental conditions Tensile strength of leads DIN IEC 68-2-21 (Ua 1) Flexibility of leads DIN IEC 68-2-21 (Ub) Sealing test A hermetisch dicht (hermetically sealed) Solderability DIN IEC 68-2-20, (Ta) 100% RoHS 6 compliant Solvent resistance DIN IEC 68-2-45 (xA) washable device Absolute Maximum Ratings Parameter Min Operable temperature range Storage temperature range -40 -50 Vectron International • Product Specifications OX-4033-EAE-1080 www.vectron.com Typ Max Units 85 85 °C °C 20-May-10 by Göhrig, Detlef Index : P3 Condition printed 2011-05-10 • page 2 of 5 OX-4033-EAE-1080-20M00 OCXO Preliminary version: Subject to technical modification. Enclosure Type G311 Height 12.2 mm all units in mm Pin Connections Pin 1: N.C. Pin 7: GND(Case) Pin 8: RF-Output Pin 14: Vs (supply voltage) Marking OX-4033-EAE-1080 20,000 MHz * VI AYYWW * pin-1 marking Vectron International • Product Specifications OX-4033-EAE-1080 www.vectron.com 20-May-10 by Göhrig, Detlef Index : P3 printed 2011-05-10 • page 3 of 5 OX-4033-EAE-1080-20M00 OCXO Preliminary version: Subject to technical modification. Reflow profile Profile Feature Pb-Free Assembly/Sn-Pb Assembly Average ramp-up rate (TL to Tp) 3°C/second max. Preheat -Temperature Min (Tsmin) 150°c -Temperature Min (Tsmax) 200°c -Time (min to max) (ts) 60-180 seconds Tsmax to TL - Ramp-up Rate 3°C/second max. Time maintainted above - Temperature (TL) 217°C - Time (tL) 60-150 seconds Peak Temperature (Tp) max 260°C Time within 5°C of actual Peak Temperature (tp) 20-40 seconds Ramp-down Rate 6°C/second max. Time 25°C to Peak Temperature 8 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Additional Information This SMD oscillator has been designed for pick and place reflow soldering. SMD oscillators must be on the top side of the PCB during the reflow process. Vectron International • Product Specifications OX-4033-EAE-1080 www.vectron.com 20-May-10 by Göhrig, Detlef Index : P3 printed 2011-05-10 • page 4 of 5 OX-4033-EAE-1080-20M00 OCXO Preliminary version: Subject to technical modification. Notes: Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C) . Preliminary version: Subject to technical modification. Vectron International • Product Specifications OX-4033-EAE-1080 www.vectron.com 20-May-10 by Göhrig, Detlef Index : P3 printed 2011-05-10 • page 5 of 5