FARM™ FARMxxxx Actual size: 2.28 x 2.2 x 0.5 in 57,9 x 55,9 x 12,7 mm ® S US C C NRTL US Filter/Autoranging Rectifier Module Up to 1000 Watts Absolute Maximum Rating Features & Benefits Parameter • RoHS compliant (with F or G pin style) Rating Unit Notes VAC VAC VDC Continuous 100ms • EMI filtering L to N voltage • Choice of 500W or 750W modules +OUT to –OUT voltage 264 280 400 • 96% efficiency B OK to –OUT voltage 16 VDC EN to –OUT voltage 16 VDC • Autoranging 115/230VAC input Mounting torque • Microprocessor controlled • Inrush current limiting • Mini sized package 4 – 6 (0.45 – 0.68) in-lbs (N-m) Operating temperature –40 to 100 °C H-Grade Storage temperature – 55 to 125 °C H-Grade 500 (260) °F (°C) <5sec; wave solder 750 (390) °F (°C) <7sec; hand solder Output current 3.5 A Baseplate temperature 100 °C Pin soldering temperature • Power fail signal • Module enable Product Highlights The FARM (Filter/Autoranging Rectifier Module) is an AC front-end module which provides EMI filtering, autoranging line rectification and inrush current limiting. The FARM is available in either 500/750W or 750/1000W models in a mini sized package measuring only 2.28” x 2.2” x 0.5”. The FARM interfaces directly with worldwide AC mains and may be used with Vicor 300V input DC-DC converters to realize an autoranging, high density, low profile switching power supply. The FARM includes a microcontroller that continuously monitors the AC line to control bridge / doubler operation. The user need only provide external capacitance to satisfy system hold-up requirements. 6 each, 4-40 screw Thermal Resistance and Capacity Parameter Min Baseplate to sink flat, greased surface with thermal pad (P/N 20264) Baseplate to ambient Free convection 1000LFM Typ Max Unit 0.16 0.14 °C/Watt °C/Watt 8.0 1.9 °C/Watt °C/Watt Part Numbering FARM Product Vicor 2nd Generation packaging technology offers flexible mounting options for various manufacturing processes. The FARM may be installed as a conventional leaded device for onboard applications, inboard for low profile, height restricted applications, socketed or surface mounted with optional ModuMate interconnect products. 1 C Type 1 = 500/750W 2 = 750/1000W Product Grade Temperatures (°C) Grade Operating Storage E = –10 to +100 –20 to +125 C = –20 to +100 –40 to +125 T = –40 to +100 –40 to +125 H = –40 to +100 –55 to +125 [1] 1 1= 2= S= N= F = G= K= Pin Style Short Pin Long Pin [1] Short ModuMate [1] Long ModuMate [1] Short RoHS [1] Long RoHS [2] Extra Long RoHS 1 Baseplate 1 = Slotted 2 = Threaded 3 = Thru hole Pin styles S, N, F & G are compatible with the ModuMate interconnect system for socketing and surface mounting [2] Not intended for socket or Surfmate mounting FARM™ Page 1 of 11 Rev 6.9 06/2017 vicorpower.com 800 927.9474 FARMxxxx Electrical Characteristics Electrical characteristics apply over the full operating range of input voltage, output power and baseplate temperature, unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate. Specifications apply for AC mains having up to 5% total harmonic distortion. INPUT SPECIFICATIONS (FARM1xxx, FARM2xxx) Parameter Operating input voltage low range high range Min Typ Max Unit Notes 132 VAC Autoranging (doubler mode) 180264 VAC Autoranging (bridge mode) 90 VAC No damage 4763 47 880 Hz Hz C-Grade T-Grade, H-Grade 90 Input undervoltage AC line frequency Power factor 0.60 Dependent on line source impedance, hold up capacitance and load. Inrush current 30 Amps 264VAC peak line OUTPUT SPECIFICATIONS FARM1xxx Parameter Min Typ Output power 0 0 Efficiency 94 Output voltage 250 FARM2xxx Max Min 500 750 0 0 96 370 Typ 94 Max Unit Notes 750 1000 Watts Watts 90 – 132VAC 180 – 264VAC 96 250 370 1,750 External hold-up capacitance 1,100 % 120/240VAC VDC 90 – 264VAC µF 2 – 3,300µF in series; HUB3300-S µF 2 – 2,200µF in series; HUB2200-S CONTROL PIN SPECIFICATIONS Parameter Min Typ Max Unit Notes AC Bus OK (B OK) Low state resistance 15 Ω Low state voltage 0.1 VDC High state voltage 14.0 15.0 15.4 VDC B OK true threshold 235 240 245 VDC B OK false threshold 200 205 210 VDC To negative output – Bus normal Bus normal 50mA max. Bus abnormal, 27kΩ internal pull up to 15VDC (see Figure11) Output Bus voltage (see Figure 8) Output Bus voltage Module Enable (EN) Low state resistance Low state voltage High state voltage 12 14 Enable threshold 235 240 Disable threshold 185 190 15 Ω 0.1 VDC 16 VDC 245 VDC 195 VDC To negative output – Converters disabled 50mA max. 150kΩ internal pull up to 15VDC (see Figure 10) Output bus voltage (see Figure 8) Output bus voltage AC Bus OK - Module Enable, differential error* 16 AC Bus OK and Module Enable thresholds track 12 14 VDC * Tracking error between BUS OK and Enable thresholds FARM™ Page 2 of 11 Rev 6.9 06/2017 vicorpower.com 800 927.9474 FARMxxxx Electrical Characteristics (Cont.) ELECTROMAGNETIC COMPATIBILITY Parameter Standard Notes 2kV–50µs Line or neutral to earth EN61000-4-5 1kV–50µs Line to neutral Transient / surge immunity Line disturbance / immunity EN61000-4-11 Flicker / inrush EN61000-3-3 Interruptions and brownouts SAFETY SPECIFICATIONS (FARM1xxx, FARM2xxx) Parameter Min Typ Isolation voltage (IN to OUT) Dielectric withstand (I/O to baseplate) Max Unit Notes None Isolation provided by DC-DC converter(s) 2,121 VDC Leakage current 1.5 Baseplate earthed mA 264 VAC AGENCY APPROVALS Safety Standards Agency Markings Notes FARM1 xxx UL60950, EN60950, CSA 60950 cTÜVus CE Marked Baseplate earthed, fast acting line fuse, Bussman ABC10 or Wickman 10A 194 series Low voltage directive FARM2 xxx UL60950, EN60950, CSA 60950 cTÜVus CE Marked Baseplate earthed, fast acting line fuse, Bussman ABC15 or Wickman 16A 194 Series Low voltage directive GENERAL SPECIFICATIONS Parameter Min MTBF Typ Max >1,000,000 Unit Notes Hours 25˚C, Ground Benign, MIL-HDBK-217F Baseplate material Aluminum Cover Ends: Zenite® 6130 Center section: Kapton insulated aluminum Pin Material Style 1 & 2 Copper, Tin / Lead plated Styles S & N (ModuMate compatible) Styles F & G (RoHS compliant) Copper, Nickel / Gold plated Copper, Nickel / Gold plated 3.1Ounces Weight (88) (grams) Size FARM™ Page 3 of 11 2.28 x 2.2 x 0.5 (57,9 x 55,9 x 12,7) Rev 6.9 06/2017 Inches (mm) vicorpower.com 800 927.9474 FARMxxxx Operating Characteristics VDC output fi VDC output Strap Engaged Enable Enable B OK B OK Figure 2 — Start up at 240VAC input Figure 1 — Start up at 120VAC input VDC output VDC output IAC input @2 A / mV IAC input @2A / mV Enable Enable B OK B OK Figure 3 — Power down, from 120VAC Figure 4 — Power down, from 240VAC VDC output Enable B OK Figure 5 — Output overvoltage protection 240VAC range FARM™ Page 4 of 11 Rev 6.9 06/2017 Figure 6 — Typical Conducted Emissions vicorpower.com 800 927.9474 FARMxxxx Application Note 2.1. If the bus voltage is greater than 200V, the doubler is not activated. The Filtered, Autoranging Rectifier Module (FARM) provides an effective solution for the AC frontend of a power supply built with Vicor DC-DC converters. This high-performance power system building block satisfies a broad spectrum of requirements and agency standards. In addition to providing transient/surge immunity and EMI filtering, the FARM contains all of the power switching and control circuitry necessary for autoranging rectification, inrush current limiting, and overvoltage protection. This module also provides converter enable and status functions for orderly power up/down control or sequencing. To complete the AC front-end configuration, the user only needs to add hold-up capacitors, and a few discrete components. Functional Description Initial Conditions: The switch that bypasses the inrush limiting PTC (positive temperature coefficient) thermistor is open when power is applied, as is the switch that engages the strap for voltage doubling. (See Figure 7). In addition, the converter modules are disabled via the Enable (EN) line, and BusOK (BOK) is high. Power Up Sequence (See Figure 8): 3.1. If the bus voltage is greater than 235V as the slope approaches zero, the inrush limiting thermistor is bypassed. Below 235V, it is not bypassed. 4.1. The converters are enabled ~150 milliseconds after the thermistor bypass switch is closed. 5.1. Bus-OK is asserted after an additional ~150 millisecond delay to allow the converter outputs to settle within specification. Power Down Sequence: (See Figure 8). When input power is turned off or fails, the following sequence occurs as the bus voltage decays: 1.2. Bus-OK is de-asserted when the bus voltage falls below 205VDC (Typical). 2.2. The converters are disabled when the bus voltage falls below 190VDC. If power is reapplied after the converters are disabled, the entire power-up sequence is repeated. If a momentary power interruption occurs and power is re-established before the bus reaches the disable threshold, the power up sequence is not repeated, i.e., the power conversion system “rides through” the momentary interruption. 1.1. Upon application of input power, the output bus capacitors begin to charge. The thermistor limits the charge current, and the exponential time constant is determined by the hold-up capacitor value and the thermistor cold resistance. The slope (dV/dt) of the capacitor voltage versus time approaches zero as the capacitors become charged to the peak of the AC line voltage. Power Up Power Down +OUT 90 – 132V AC Line PTC Thermistor L Strap Strap Output Bus (VDC) EMI Filter –OUT N EN Microcontroller BOK EMI GRD Figure 7 — Functional block diagram: autoranging rectifier FARM™ Page 5 of 11 Rev 6.9 06/2017 Strap 400 300 200 100 0 1.1 2.1 PTC Thermistor Bypass Converter Enable Bus OK 3.1 ~150ms ~150ms 4.1 5.1 2.2 1.2 Figure 8 — Timing diagram: power up/down sequence vicorpower.com 800 927.9474 Timing Diagram, Power Up/Down Sequence FARMxxxx Application Note (Cont.) Off-Line Power Supply Configuration The FARM maintains the DC output bus voltage between 250 and 370VDC over the entire input voltage range, which is compatible with Vicor 300V input converters. The FARM automatically switches to the proper bridge or doubler mode depending on the input voltage, eliminating the possibility of damage due to improper line connection. The FARM1xxx is rated at 500W in the low range (90 – 132VAC input), and 750W in the high range (180 – 264VAC input). The FARM2xxx is rated for 750W and 1000W for the low and high input ranges respectively. Either of these modules can serve as the AC front end for any number and combination of compatible converters as long as the maximum power rating is not exceeded. Strap (ST) Pin: In addition to input and output power pin connections, it is necessary to connect the Strap pin to the center junction of the series hold-up capacitors (C1, C2, see Figure 9) for proper (autoranging) operation. Metal oxide varistors, V1 and V2 provide capacitor protection. The bleeder resistors (R1, R2, see Figure 9) discharge the hold-up capacitors when power is switched off. Capacitors C7 and C8 are recommended if the hold-up capacitors are located more than 3 inches (75mm) from the FARM output pins. Enable (EN) Pin: (See Figure 10) The Enable pin must be connected to the PC or Gate-In pin of all converter modules to disable the converters during power up. Otherwise, the converters would attempt to start while the hold-up capacitors were being charged through an unbypassed current limiting thermistor, preventing the bus voltage from reaching the thermistor bypass threshold, thus disabling the power supply. The Enable output (the drain of an N channel MOSFET) is internally pulled up to 15V through a 150kΩ resistor. A signal diode should be placed close to and in series with the PC or (Gate-In) pin of each converter to eliminate the possibility of control interference between converters. The Enable pin switches to the high state (15V) with respect to the negative output power pin to turn on the converters after the power up inrush is over. The Enable function also provides input overvoltage protection for the converters by turning off the converters if the DC bus voltage exceeds 400VDC. The thermistor bypass switch opens if this condition occurs, placing the thermistor in series with the input voltage, which reduces the bus voltage to a safe level while limiting input current in case the varistors conduct. The thermistor bypass switch also opens if a fault or overload reduces the bus voltage to less than 180VDC. CAUTION: There is no input to output isolation in the FARM, hence the –OUT of the FARM and thus the –In of the downstream DC-DC converter(s) are at a high potential. If it is necessary to provide an external enable/ disable function by controlling the DC-DC converter’s PC pin (referenced to the –IN) of the converter an opto-isolator or isolated relay should be employed. C3 N EMI GND Z1 L PE Part C1,2 C3-C6 C7,8** C9 C10,C11 D1, 2 D3, 4 F1, F2 R1, 2 R3, 4*** V1,2 Z1 C9 * F3 Vicor Description Part Number Hold-up capacitors 4,700pF (Y2 type) 01000 Film Cap., 0.61µF 34610 0.47µF 03047 0.001µF Diode 00670 1N5817 26108 Use recommended fusing for specific DC-DC Converters 150kΩ, 0.5W 250Ω 220VMOV 30234-220 MOV 270 30076 R1 + N FARM BOK Filter/Autoranging ST Rectifier Module EN N/C L C1 F1 D3 C8** V2 – R2 PC (GATE IN) PR Vicor DC-DC Converter –IN C2 R3 C4 D1 C5 Sizing PCB traces: All traces shown in bold carry significant current and should be sized accordingly. N/ST/L ± IN 10A RMS at 90VAC and 500W 4 ADC at 190VDC and 750W FARM2-xxx N/ST/L 20A RMS at 90VAC and 750W ± IN 8ADC at 190VDC and 1000W * See Agency Approvals on FARM data sheet. **Required if C1 & C2 are located more than 3 in (75mm) from output of the FARM. ***Not used with VI-260/VI-J60 F2 R4 +IN C11 D2 D4 –IN C6 Figure 9 — Offline Power Supply Configuration Rev 6.9 06/2017 PC (GATE IN) PR Not used with VI-260/VI-J60 To additional modules FARM™ Page 6 of 11 +IN C10 C7** V1 vicorpower.com 800 927.9474 Vicor DC-DC Converter FARMxxxx Application Note (Cont.) Bus-OK (BOK) Pin: (See Figure 11) The Bus-OK pin is intended to provide early-warning power fail information and is also referenced to the negative output pin. Not used with VI-260/VI-J60 N EMI GND N/C L +IN + 15 VDC 150k FARM Microcontroller PC (GATE IN) BOK ST EN PR – –IN Vicor DC-DC Converter Figure 10 — Enable (EN) function + N EMI GND 15 VDC PC BOK Secondary referenced ST N/C L Microcontroller +IN +5 VDC EN PR – –IN Vicor DC-DC Converter CAUTION: There is no input-to-output isolation in the FARM. It is necessary to monitor Bus OK via an optoisolator if it is to be used on the secondary (output) side of the converters. A line-isolation transformer should be used when performing scope measurements. Scope probes should never be applied simultaneously to the input and output as this will damage the module. Filter: (See Figure 12) An integral input filter consists of a common mode choke and Y rated capacitors (line-ground) plus two X rated capacitors (line-line). This filter configuration provides common mode and differential mode insertion loss in the frequency range between 100kHz and 30MHz as illustrated in Figure 6. Hold-up Capacitors: Hold-up capacitor values should be determined according to output bus voltage ripple, power fail hold-up time, and ride-through time (See Figure 13). Many applications require the power supply to maintain output regulation during a momentary power failure of specified duration, i.e., the converters must hold-up or ride- through such an event while maintaining undisturbed output voltage regulation. Similarly, many of these same systems require notification of an impending power failure in order to allow time to perform an orderly shut down. The energy stored on a capacitor which has been charged to voltage V is: Figure 11 — Bus OK (BOK) isolated power status indicator ε = 1/2(CV2) Where: N L1 0.47µF N/C ε = stored energy C = capacitance V = voltage across the capacitor + 330µH EMI GND (1) CM 4.7nF 0.099µF BOK ST Energy is given up by the capacitors as they are discharged by the converters. The energy expended (the power-time product) is: EN 4.7nF – L ε = PΔt = C(V12–V22) / 2 Where: Figure 12 — Internal filter (2) P = operating power Δt = discharge interval V1 = capacitor voltage at the beginning of Δt V2 = capacitor voltage at the end of Δt Rearranging Equation 2 to solve for the required capacitance: C = 2PΔt / (V12–V22) FARM™ Page 7 of 11 Rev 6.9 06/2017 vicorpower.com 800 927.9474 (3) FARMxxxx Application Note (Cont.) Example The power fail warning time (∆t) is defined as the interval between B OK and converter shut down (EN) as illustrated in Fig. 13. The Bus-OK and Enable thresholds are 205V and 190V, respectively. A simplified relationship between power fail warning time, operating power, and bus capacitance is obtained by inserting these constants: In this example, the output required from the DC-DC converter at the point of load is 12VDC at 320W. Therefore, the output power from the FARM would be 375W (assuming a converter efficiency of 85%). The desired hold-up time is 9ms over an input range of 90 to 264VAC. C = 2PΔt / (2052 – 1902) C = 2PΔt / (5,925) It should be noted that the series combination (C1, C2, See Figure 9) requires each capacitor to be twice the calculated value, but the required voltage rating of each capacitor is reduced to 200V. Allowable ripple voltage on the bus (or ripple current in the capacitors) may define the capacitance requirement. Consideration should be given to converter ripple rejection and resulting output ripple voltage. For example, a converter whose output is 15V and nominal input is 300V will provide approximately 56dB ripple rejection, i.e., 10Vp-p of input ripple will produce 15mVp-p of output ripple (See Figure 17). Equation 3 is again used to determine the required capacitance. In this case, V1 and V2 are the instantaneous values of bus voltage at the peaks and valleys (See Figure 13) of the ripple, respectively. The capacitors must hold-up the bus voltage for the time interval (∆t) between peaks of the rectified line as given by: Δt = (π – θ) / 2πf Where: (4) The approximate conduction angle is given by: (5) Another consideration in hold-up capacitor selection is their ripple current rating. The capacitors’ rating must be higher than the maximum operating ripple current. The approximate operating ripple current (rms) is given by: IRMS = 2P/VAC Where: Determining Ride-through Time: Figure 15 illustrates ridethrough time as a function of line voltage and output power, and shows that at a nominal line of 90VAC, ride-through would be 68ms. Ride-through time is a function of line voltage. Determining Ripple Voltage on the Hold-up Capacitors: Figure 16 is used to determine ripple voltage as a function of operating power and bus capacitance, and shows that the ripple voltage across the hold-up capacitors will be 12Vp-p. Determining the Ripple on the Output of the DC-DC Converter:. Figure 17 is used to determine the approximate ripple rejection of the DC-DC converter and indicates a ripple rejection of approximately 60dB for a 12V output. Since the ripple on the bus voltage is 12VAC and the ripple rejection of the converter is 60dB, the output ripple of the converter due to ripple on its input (primarily 120Hz) will be 12mVp-p. For more information about designing an autoranging AC input power supply using the FARM and Vicor DC-DC converter modules, contact Vicor Applications Engineering at the nearest Vicor Technical Support Center, or send email to: [email protected]. f = line frequency θ = rectifier conduction angle θ = Cos-1V2 /V1 Determining Required Capacitance for Power Fail Warning: Figure 14 is used to determine capacitance for a given power fail warning time and power level, and shows that the total bus capacitance must be at least 820µF. Since two capacitors are used in series, each capacitor must be at least 1,640µF. Note that warning time is not dependent on line voltage. A hold-up capacitor calculator is available on the Vicor website, at: vicorpower.com/hubcalc. (6) P = operating power level VAC = operating line voltage Storage Vicor products, when not installed in customer units, should be stored in ESD safe packaging in accordance with ANSI/ ESD S20.20, “Protection of Electrical and Electronic Parts, Assemblies and Equipment” and should be maintained in a temperature controlled factory/ warehouse environment not exposed to outside elements controlled between the temperature ranges of 15°C and 38°C. Humidity shall not be condensing, no minimum humidity when stored in an ESD compliant package. Calculated values of bus capacitance for various hold-up time, ride-through time, and ripple voltage requirements are given as a function of operating power level in Figures 14, 15, and 16, respectively. FARM™ Page 8 of 11 Rev 6.9 06/2017 vicorpower.com 800 927.9474 FARMxxxx Application Note (Cont.) Hold-up Time Ripple (Vp-p) π–θ Power Fail Warning θ 254V 205V 190V Ride-Through Time Bus OK Power Fail Converter Shut down Figure 13 — Hold-up time 100 (FARM2XXX) 30 * 25 (FARM1XXX) 20 15 10 5 0 250 Total capacitance 820μF 90 35 * 80 60 50 40 30 20 500 Figure 14 — Power fail warning time vs. operating power and total bus capacitance, series combination of C1, C2 (See Figure 9) 15 80 * 75 * 10 5 0 250 1100μF 1300μF 500 820μF 1600μF 1000 Figure 15 — Ride-through time vs. operating power Ripple Rejection (dB) P-P Ripple Voltage (VAC) 20 750 Operating Power (W) Operating Power (W) 25 115VAC 70 0 250 1000 750 30 90VAC 10 * 500 Ride-through Time (ms) Power Fail Warning Time (ms) 40 680μF * 2200μF (FARM1XXX) (FARM2XXX) 750 1000 70 65 60 55 50 45 40 2 5 15 30 50 Output Voltage Operating Power (W) Figure 16 — Ripple voltage vs. operating power and bus capacitance, series combination of C1, C2 (See Figure 9) Figure 17 — Converter ripple rejection vs. output voltage (typical) FARM™ Page 9 of 11 vicorpower.com 800 927.9474 Rev 6.9 06/2017 FARMxxxx Mechanical Drawings 12 7 7 6 6 0.700 * 17,78 0.700 *1.000 * 17,78 25,40 1.000 *1.400 * 25,40 35,56 1.400 * ications 35,56 5 2.20 55,9 1.76 44,7 2.20 55,9 1.76 44,7 0.23 0.23 (REF) (REF) 5,8 5,8 1 0.3000.300 ±0.015 ±0.015 7,62 ±0,38 7,62 ±0,38 9 5 0.400 10,16 FULL R (6X) Slotted FULL R (6X) 3 style 2 & 3style 2 & 0.12* 0.20** 0.12* 0.20** only baseplatesbaseplates only 3,1 5,1 3,1 5,1 (4X)*** (4X)*** (6X) * DENOTES TOL= ±0.003 ±0,08 3,3 (6X) Threaded 9 7 4 3 4 1.900 48,26 6 8 7 5 6 0.13 3,3 Pin CL 1.900 48,26 Pin CL 0.080 DIA,(7X) 2,03 Thru Hole #30 Drill Thru (6X) (0.1285) *** Reserved for Vicor Not for mounting CL Pin center line Thru Hole #30 Drill Thru (6X) (0.1285) PLATED THROUGH HOLE DIA 1.790** 45,47 0.06 (4X) 1,5 1 2 INBOARD SOLDER MOUNT ONBOARD SOLDER MOUNT SHORT PIN STYLE LONG PIN STYLE (7X) 0.094 ±0.003 2,39 ±0,08 0.094 ±0.003 2,39 ±0,08 (2X) 0.164 ±0.003 4,16 ±0,08 0.164 ±0.003 4,16 ±0,08 3,30 0.06 (3X) 55,9 (REF.) 1,5 13,7 (9X) Pin Style 1&S (Short Pin) 15,7 (9X) Pin Style 2&N (Long Pin) (6X) 0.130 3,30 (6X) Use a 4-40 Screw (6X) Torque to: Use a 4-40 Screw (6X) 5 in-lbs Torque to: 0.57 N-m 2.20 R FULL R (6X) 0.130 33,0 (3X) FULL R (6X) 5 in-lbs 0.57 N-m 2.20 55,9 (REF.) Pin Style K (Extra Long Pin) 0.71 (9X) Pin Style K 3 8 7 6 ONBOARD SOCKET SURFACE MOUNT SOCKET SURFACE MOUNT 0.183 ±0.003 4,65 ±0,08 N/A ALL MARKINGS0.266 ±0.003 THIS SURFACE 6,76 ±0,08 N/A PINS STYLES SOLDER:TIN / LEAD PLATED MODUMATE: GOLD PLATED COPPER RoHS: GOLD ALUMINUM PLATED COPPER 4 BASEPLATE PINS STYLES SOLDER:TIN / LEAD PLATED MODUMATE: GOLD PLATED COPPER RoHS: GOLD PLATED COPPER 5 00.45 43 0.45 11,5 0.700* 17,78 1.000* 25,40 1.400* 35,56 ALL MARKINGS THIS SURFACE INBOARD SOCKET MOUNT ALUMINUM BASEPLATE 1.575** 40,00 9 0.53 13,5 ** PCB WINDOW Rev 6.9 06/2017 0.46 11,7 0.56 14,2 SOCKETS SOCKET HEADERS 0.080" DIA. PINS (7X) (SURFACE MOUNT) Consult Vicor Application Note: P/N 13632 (100 pcs.) KIT INCLUDES 0.150"procedures DIA. PINS (2X) for INPUT & OUTPUT Soldering methods and P/N 13633 (100 pcs.) P/N 16021 1st and 2nd Generation modules. P/N 16019 (9 pc. Kit) ±0.003 * DENOTES TOL = ±0,08 PCB Mounting Specifications FARM™ Page 10 of 11 0.06 1,5 0.43 0.10 X 45˚ 2,5 CHAMFER 18,0 NOTES: (Extra Long Pin) 1. MATERIAL: BASE: 6000 SERIES ALUMINUM NOTES: COVER: LCP, ALUMINUM 3003 H14 RoHS PINS GOLD PLATE 30 MICRO INCH MIN; NON-RoHS 1. MATERIAL: accessoriesPINS: PINS: TIN/LEAD BRIGHT BASE:90/10 6000 SERIES ALUMINUM 2. DIMENSIONSCOVER: AND VALUES BRACKETS ARE LCP,IN ALUMINUM 3003METRIC H14 3. MANUFACTURING IS IN PLACE ENSURE THAT THE SPACING PINS: CONTROL RoHS PINS GOLDTO PLATE 30 MICRO INCH MIN; NON-RoHS BETWEEN THE MODULES LABEL SURFACE TO THE PRINTED CIRCUIT BOARD PINS: TIN/LEAD 90/10 BRIGHT OF THE APPLICATION RANGES FROM DIRECT CONTACT (ZERO), TO THE 2. DIMENSIONS AND VALUES IN BRACKETS ARE METRIC MAXIMUM GAP AS CALCULATED FROM THE TOLERANCE STACK-UP 3.SUBJECT MANUFACTURING CONTROL IS IN PLACE TO ENSURE THAT THE SPACING AND IS NOT NEGATIVE TOLERANCE ACCUMULATION 0.158 4,01 1.900* 48.26 48,26 0.195 4,95 R 0.54 10,9 (9X) Pin Style 1&S 13,7 (Short 0.54Pin) 0.10 X 45˚ 2,5 CHAMFER BETWEEN THE MODULES LABEL SURFACE TO THE PRINTED CIRCUIT BOARD OF THE APPLICATION RANGES FROM DIRECT CONTACT (ZERO), TO THE MAXIMUM GAP AS CALCULATED FROM THE TOLERANCE STACK-UP AND IS NOT SUBJECT NEGATIVE TOLERANCE ACCUMULATION 0.062 ±0.010 PCB THICKNESS 1,57 ±0,25 0.400* 10,16 0.43 10,9 0.71 (9X) 18,0 Module Outline R 0.35 0.65 (2X) 0.65 8,8 16,5 16,5 2.28 1.30 2.28 1.30 ALUMINUM 57,9 33,0 BASEPLATE ALUMINUM 57,9 BASEPLATE 0.10 2,5 50,80 2,5 50,80 0.62 (9X) Pin Style 2&N 15,7 (Long 0.62Pin) * Style 1 baseplate only ** Style 2 & 3 baseplates *** Reserved for 1Vicor accessories * Style baseplate only Not for mounting Style 2 & 3 baseplates CL Pin**center line 4-40 UNC-2B (6X) 2.000 0.10 2.000 5 1.400 35,56 Threaded 0.49 12,4 0.49 12,4 0.35 (2X) 8,8 0.150 DIA,(2X) 3,81 0.150 DIA,(2X) 0.080 DIA,(7X) 3,81 2,03 0.400 0.700 10,16 17,78 4-40 UNC-2B (6X) ns 8 23 1.0000.700 25,4017,78 1.4001.000 35,5625,40 Slotted0.13 * DENOTES TOL= ±0.003 ±0,08 21 0.01 0.01 0.3000.300 ±0.015±0.015 7,62 ±0,38 7,62 ±0,38 (ALL MARKINGS THIS SURFACE) 8 8 3 3 4 4 0.50 ±0.02 0.50 ±0.02 12,7 ±0,5 12,7 ±0,5 (ALL MARKINGS THIS SURFACE) 9 2 Converter Pins No. Function Label 1 Neutral N 2 EMI GND 3 NC (9X)PLATED PLATED 4(9X) Line L THROUGH HOLE DIA THROUGH HOLE DIA 5 –OUT – 6 Enable EN 7 Strap ST 8 BUS OK BOK 9 +OUT + vicorpower.com 800 927.9474 FARMxxxx Vicor’s comprehensive line of power solutions includes high density AC-DC and DC-DC modules and accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power systems. Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication. Vicor reserves the right to make changes to any products, specifications, and product descriptions at any time without notice. Information published by Vicor has been checked and is believed to be accurate at the time it was printed; however, Vicor assumes no responsibility for inaccuracies. Testing and other quality controls are used to the extent Vicor deems necessary to support Vicor’s product warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. Specifications are subject to change without notice. Visit http://www.vicorpower.com/ac-dc/input-modules/filter-autoranging-rectifier for the latest product information. Vicor’s Standard Terms and Conditions and Product Warranty All sales are subject to Vicor’s Standard Terms and Conditions of Sale, and Product Warranty which are available on Vicor’s webpage (http://www.vicorpower.com/termsconditionswarranty) or upon request. Life Support Policy VICOR’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF VICOR CORPORATION. As used herein, life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. Per Vicor Terms and Conditions of Sale, the user of Vicor products and components in life support applications assumes all risks of such use and indemnifies Vicor against all liability and damages. Intellectual Property Notice Vicor and its subsidiaries own Intellectual Property (including issued U.S. and Foreign Patents and pending patent applications) relating to the products described in this data sheet. No license, whether express, implied, or arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Interested parties should contact Vicor’s Intellectual Property Department. Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 Fax: 978-475-6715 email Customer Service: [email protected] Technical Support: [email protected] FARM™ Page 11 of 11 Rev 6.9 06/2017 vicorpower.com 800 927.9474