OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 0.03-μV/°C Drift, Low-Noise, Rail-to-Rail Output, 36-V, Zero-Drift OPERATIONAL AMPLIFIERS Check for Samples: OPA2188 FEATURES DESCRIPTION 1 • • • • • • • The OPA2188 operational amplifier uses TI proprietary auto-zeroing techniques to provide low offset voltage (25 μV, max), and near zero-drift over time and temperature. This miniature, high-precision, low quiescent current amplifier offers high input impedance and rail-to-rail output swing within 15 mV of the rails. The input common-mode range includes the negative rail. Either single or dual supplies can be used in the range of +4.0 V to +36 V (±2 V to ±18 V). Low Offset Voltage: 25 μV (max) Zero-Drift: 0.03 μV/°C Low Noise: 8.8 nV/√Hz 0.1-Hz to 10-Hz Noise: 0.25 µVPP Excellent DC Precision: PSRR: 142 dB CMRR: 146 dB Open-Loop Gain: 136 dB Gain Bandwidth: 2 MHz Quiescent Current: 475 μA (max) Wide Supply Range: ±2 V to ±18 V Rail-to-Rail Output: Input Includes Negative Rail RFI Filtered Inputs MicroSIZE Packages The OPA2188 is available in MSOP-8 and SO-8 packages. The device is specified for operation from –40°C to +105°C. 145 APPLICATIONS • • • • • • • • • OPA2188 Zero-Drift Architecture Precision Laser Trim Architecture 125 Offset Voltage (mV) • • • 2 Bridge Amplifiers Strain Gauges Test Equipment Transducer Applications Temperature Measurement Electronic Scales Medical Instrumentation Resistance Temperature Detectors Precision Active Filters 105 85 65 45 25 5 -55 -35 -15 5 25 45 65 85 105 125 Temperature (°C) Zero-Drift Amplifier Portfolio VERSION Single Dual Quad PRODUCT OFFSET VOLTAGE (µV) OFFSET VOLTAGE DRIFT (µV/°C) OPA188 (4 V to 36 V) 25 0.085 2 OPA333 (5 V) 10 0.05 0.35 BANDWIDTH (MHz) OPA378 (5 V) 50 0.25 0.9 OPA735 (12 V) 5 0.05 1.6 OPA2188 (4 V to 36 V) 25 0.085 2 OPA2333 (5 V) 10 0.05 0.35 OPA2378 (5 V) 50 0.25 0.9 OPA2735 (12 V) 5 0.05 1.6 OPA4188 (4 V to 36 V) 25 0.085 2 OPA4330 (5 V) 50 0.25 0.35 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2011–2012, Texas Instruments Incorporated OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE INFORMATION (1) PRODUCT PACKAGELEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING SO-8 D –40°C to +105°C 2188 MSOP-8 DGK –40°C to +105°C 2188 OPA2188 (1) ORDERING NUMBER TRANSPORT MEDIA, QUANTITY OPA2188AID Rails, 100 OPA2188AIDR Tape and Reel, 2500 OPA2188AIDGKT Tape and Reel, 250 OPA2188AIDGKR Tape and Reel, 2500 For the most current package and ordering information, see the Package Option Addendum at the end of this document, or visit the device product folder at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) Supply voltage Signal input terminals (2) VALUE UNIT ±20, 40 (single supply) V Voltage (V–) – 0.5 to (V+) + 0.5 V Current ±10 mA Output short-circuit (3) Temperature range Electrostatic discharge (ESD) ratings (1) (2) (3) 2 Continuous Operating, TA –55 to +125 °C Storage, Tstg –65 to +150 °C Junction, TJ +150 °C 1.5 kV 1 kV Human body model (HBM) Charged device model (CDM) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only and functional operation of the device at these or any other conditions beyond those specified is not implied. Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5 V beyond the supply rails should be current-limited to 10 mA or less. Short-circuit to ground, one amplifier per package. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 ELECTRICAL CHARACTERISTICS: High-Voltage Operation, VS = ±4 V to ±18 V (VS = +8 V to +36 V) At TA = +25°C, RL = 10 kΩ connected to VS / 2, and VCOM = VOUT = VS / 2, unless otherwise noted. OPA2188 PARAMETER CONDITIONS MIN TYP MAX UNIT OFFSET VOLTAGE VOS Input offset voltage PSRR Power-supply rejection ratio VS = 4 V to 36 V, VCM = VS / 2 25 0.085 μV/°C 0.075 0.3 μV/V 0.3 μV/V VS = 4 V to 36 V, VCM = VS / 2, TA = –40°C to +105°C Long-term stability 4 Channel separation, dc μV 6 0.03 TA = –40°C to +105°C (1) μV μV/V 1 INPUT BIAS CURRENT IB Input bias current IOS Input offset current VCM = VS / 2 ±160 TA = –40°C to +105°C ±320 TA = –40°C to +105°C ±850 pA ±4 nA ±1700 pA ±2 nA NOISE 0.25 μVPP f = 1 kHz 8.8 nV/Hz f = 1 kHz 7 fA/Hz en Input voltage noise f = 0.1 Hz to 10 Hz en Input voltage noise density in Input current noise density INPUT VOLTAGE RANGE VCM Common-mode voltage range CMRR Common-mode rejection ratio V– (V+) – 1.5 V (V–) < VCM < (V+) – 1.5 V 120 134 dB (V–) + 0.5 V < VCM < (V+) – 1.5 V, VS = ±18 V 130 146 dB (V–) + 0.5 V < VCM < (V+) – 1.5 V, VS = ±18 V, TA = –40°C to +105°C 120 126 dB INPUT IMPEDANCE Differential 100 || 6 MΩ || pF Common-mode 6 || 9.5 1012 Ω || pF OPEN-LOOP GAIN AOL Open-loop voltage gain (V–) + 500 mV < VO < (V+) – 500 mV, RL = 10 kΩ 130 136 dB (V–) + 500 mV < VO < (V+) – 500 mV, RL = 10 kΩ, TA = –40°C to +105°C 120 126 dB FREQUENCY RESPONSE GBW Gain-bandwidth product SR Slew rate Settling time, 0.1% THD+N (1) 2 MHz G = +1 0.8 V/μs VS = ±18 V, G = 1, 10-V step 20 μs Settling time, 0.01% VS = ±18 V, G = 1, 10-V step 27 μs Overload recovery time VIN × G = VS 1 μs Total harmonic distortion + noise 1 kHz, G = 1, VOUT = 1 VRMS 0.0001 % 1000-hour life test at +125°C demonstrated randomly distributed variation in the range of measurement limits—approximately 4 μV. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 3 OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com ELECTRICAL CHARACTERISTICS: High-Voltage Operation, VS = ±4 V to ±18 V (VS = +8 V to +36 V) (continued) At TA = +25°C, RL = 10 kΩ connected to VS / 2, and VCOM = VOUT = VS / 2, unless otherwise noted. OPA2188 PARAMETER CONDITIONS MIN TYP MAX UNIT OUTPUT No load Voltage output swing from rail ISC Short-circuit current RO Open-loop output resistance CLOAD Capacitive load drive 6 15 mV RL = 10 kΩ 220 250 mV RL = 10 kΩ, TA = –40°C to +105°C 310 350 mV ±18 f = 1 MHz, IO = 0 mA 120 Ω 1 nF POWER SUPPLY VS IQ Operating voltage range Quiescent current (per amplifier) 4 to 36 (±2 to ±18) VS = ±4 V to VS = ±18 V 415 IO = 0 mA, TA = –40°C to +105°C V 475 μA 525 μA TEMPERATURE RANGE Temperature range 4 Specified –40 +105 °C Operating –40 +125 °C Storage –65 +150 °C Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 ELECTRICAL CHARACTERISTICS: Low-Voltage Operation, VS = ±2 V to < ±4 V (VS = +4 V to < +8 V) At TA = +25°C, RL = 10 kΩ connected to VS / 2, and VCOM = VOUT = VS / 2, unless otherwise noted. OPA2188 PARAMETER CONDITIONS MIN TYP MAX UNIT OFFSET VOLTAGE VOS Input offset voltage PSRR Power-supply rejection ratio TA = –40°C to +105°C VS = 4 V to 36 V, VCM = VS / 2 25 0.085 μV/°C 0.075 0.3 μV/V 0.3 μV/V VS = 4 V to 36 V, VCM = VS / 2, TA = –40°C to +105°C Long-term stability 4 Channel separation, dc μV 6 0.03 (1) μV 1 μV/V INPUT BIAS CURRENT IB Input bias current IOS Input offset current VCM = VS / 2 ±160 TA = –40°C to +105°C ±320 TA = –40°C to +105°C ±850 pA ±4 nA ±1700 pA ±2 nA NOISE en in 0.25 μVPP f = 1 kHz 8.8 nV/Hz f = 1 kHz 7 fA/Hz Input voltage noise f = 0.1 Hz to 10 Hz Input voltage noise density Input current noise density INPUT VOLTAGE RANGE VCM Common-mode voltage range CMRR Common-mode rejection ratio TA = –40°C to +105°C V– (V+) – 1.5 V (V–) < VCM < (V+) – 1.5 V 106 114 dB (V–) + 0.5 V < VCM < (V+) – 1.5 V, VS = ±2 V 114 120 dB (V–) + 0.5 V < VCM < (V+) – 1.5 V, VS = ±2 V, TA = –40°C to +105°C 110 120 dB INPUT IMPEDANCE Differential Common-mode 100 || 6 MΩ || pF 6 || 95 1012 Ω || pF OPEN-LOOP GAIN AOL Open-loop voltage gain (V–) + 500 mV < VO < (V+) – 500 mV, RL = 5 kΩ, VS = 5 V 110 120 dB (V–) + 500 mV < VO < (V+) – 500 mV, RL = 10 kΩ 120 130 dB (V–) + 500 mV < VO < (V+) – 500 mV, RL = 10 kΩ, TA = –40°C to +105°C 114 120 dB FREQUENCY RESPONSE GBW Gain-bandwidth product SR Slew rate G = +1 Overload recovery time VIN × G = VS Total harmonic distortion + noise 1 kHz, G = 1, VOUT = 1 VRMS THD+N (1) 2 MHz 0.8 V/μs 1 μs 0.0001 % 1000-hour life test at +125°C demonstrated randomly distributed variation in the range of measurement limits—approximately 4 μV. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 5 OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com ELECTRICAL CHARACTERISTICS: Low-Voltage Operation, VS = ±2 V to < ±4 V (VS = +4 V to < +8 V) (continued) At TA = +25°C, RL = 10 kΩ connected to VS / 2, and VCOM = VOUT = VS / 2, unless otherwise noted. OPA2188 PARAMETER CONDITIONS MIN TYP MAX UNIT OUTPUT No load Voltage output swing from rail ISC Short-circuit current RO Open-loop output resistance CLOAD Capacitive load drive 6 15 mV RL = 10 kΩ 220 250 mV RL = 10 kΩ, TA = –40°C to +105°C 310 350 mV ±18 f = 1 MHz, IO = 0 mA 120 Ω 1 nF POWER SUPPLY VS Operating voltage range IQ 4 to 36 (±2 to ±18) VS = ±2 V to VS = ±4 V Quiescent current (per amplifier) V 385 IO = 0 mA, TA = –40°C to +105°C 440 μA 525 μA TEMPERATURE RANGE Temperature range Specified –40 +105 °C Operating –40 +125 °C Storage –65 +150 °C THERMAL INFORMATION: OPA2188 OPA2188ID THERMAL METRIC (1) OPA2188IDGK D DGK 8 PINS 8 PINS θJA Junction-to-ambient thermal resistance 111.0 159.3 θJCtop Junction-to-case (top) thermal resistance 54.9 37.4 θJB Junction-to-board thermal resistance 51.7 48.5 ψJT Junction-to-top characterization parameter 9.3 1.2 ψJB Junction-to-board characterization parameter 51.1 77.1 θJCbot Junction-to-case (bottom) thermal resistance n/a n/a (1) UNITS °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. PIN CONFIGURATION D, DGK PACKAGES SO-8, MSOP-8 (TOP VIEW) OUT A 6 1 -IN A 2 +IN A 3 V- 4 A B 8 V+ 7 OUT B 6 -IN B 5 +IN B Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 TYPICAL CHARACTERISTICS Table 1. Characteristic Performance Measurements DESCRIPTION FIGURE Offset Voltage Production Distribution Figure 1 Offset Voltage Drift Distribution Figure 2 Offset Voltage vs Temperature Figure 3 Offset Voltage vs Common-Mode Voltage Figure 4, Figure 5 Offset Voltage vs Power Supply Figure 6 IB and IOS vs Common-Mode Voltage Figure 7 Input Bias Current vs Temperature Figure 8 Output Voltage Swing vs Output Current (Maximum Supply) Figure 9 CMRR and PSRR vs Frequency (Referred-to-Input) Figure 10 CMRR vs Temperature Figure 11, Figure 12 PSRR vs Temperature Figure 13 0.1-Hz to 10-Hz Noise Figure 14 Input Voltage Noise Spectral Density vs Frequency Figure 15 THD+N Ratio vs Frequency Figure 16 THD+N vs Output Amplitude Figure 17 Quiescent Current vs Supply Voltage Figure 18 Quiescent Current vs Temperature Figure 19 Open-Loop Gain and Phase vs Frequency Figure 20 Closed-Loop Gain vs Frequency Figure 21 Open-Loop Gain vs Temperature Figure 22 Open-Loop Output Impedance vs Frequency Figure 23 Small-Signal Overshoot vs Capacitive Load (100-mV Output Step) Figure 24, Figure 25 No Phase Reversal Figure 26 Positive Overload Recovery Figure 27 Negative Overload Recovery Figure 28 Small-Signal Step Response (100 mV) Figure 29, Figure 30 Large-Signal Step Response Figure 31, Figure 32 Large-Signal Settling Time (10-V Positive Step) Figure 33 Large-Signal Settling Time (10-V Negative Step) Figure 34 Short-Circuit Current vs Temperature Figure 35 Maximum Output Voltage vs Frequency Figure 36 Channel Separation vs Frequency Figure 37 EMIRR IN+ vs Frequency Figure 38 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 7 OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT DISTRIBUTION 40 Distribution Taken From 1400 Amplifiers Percentage of Amplifiers (%) 16 14 12 10 8 6 4 Distribution Taken From 78 Amplifiers 35 30 25 20 15 10 5 2 OFFSET VOLTAGE vs TEMPERATURE 5 Typical Units Shown VS = ±18 V 0 0 -5 -5 -10 -10 -55 -35 -15 5 25 45 65 85 105 -15 -2.5 125 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5 VCM (V) Temperature (°C) Figure 3. Figure 4. OFFSET VOLTAGE vs COMMON-MODE VOLTAGE OFFSET VOLTAGE vs POWER SUPPLY 15 5 Typical Units Shown VS = ±18 V 5 Typical Units Shown VSUPPLY = ±2 V to ±18 V 10 5 VOS (mV) 5 VOS (mV) 0.09 5 VOS (mV) VOS (mV) 5 Typical Units Shown VS = ±2 V 10 -15 0 0 -5 -5 -10 -10 -15 -15 -20 -15 -10 -5 0 5 10 15 20 0 VCM (V) 2 4 6 8 10 12 14 16 18 20 VSUPPLY (V) Figure 5. 8 0.08 OFFSET VOLTAGE vs COMMON-MODE VOLTAGE 15 5 10 0.07 Figure 2. 15 15 0.06 Offset Voltage Drift (mV/°C) Figure 1. 10 0.05 0.04 0.01 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 18 20 Offset Voltage (mV) 0.1 0 0 0.03 Percentage of Amplifiers (%) 18 0.02 20 Figure 6. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 TYPICAL CHARACTERISTICS (continued) VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. IB AND IOS vs COMMON-MODE VOLTAGE 500 INPUT BIAS CURRENT vs TEMPERATURE 4000 IB+ +IB 400 IB and IOS (pA) IOS Input Bias Current (pA) IOS 300 IB- 3000 -IB 200 100 0 -100 2000 1000 0 -1000 -200 -300 -2000 -20 -15 -10 0 -5 5 10 15 20 -55 -35 5 -15 65 85 105 Figure 8. OUTPUT VOLTAGE SWING vs OUTPUT CURRENT (Maximum Supply) CMRR AND PSRR vs FREQUENCY (Referred-to-Input) 125 160 -40°C +85°C +125°C 140 120 100 80 60 40 +PSRR -PSRR CMRR 20 0 0 2 4 6 8 10 12 14 16 18 20 22 1 24 10 100 Figure 9. 10k 100k 1M Figure 10. CMRR vs TEMPERATURE CMRR vs TEMPERATURE Common-Mode Rejection Ratio (mV/V) 40 (V-) < VCM < (V+) - 1.5 V 35 1k Frequency (Hz) Output Current (mA) Common-Mode Rejection Ratio (mV/V) 45 Figure 7. 20 19 18 17 16 15 14 -14 -15 -16 -17 -18 -19 -20 30 25 Temperature (°C) Common-Mode Rejection Ratio (dB), Power-Supply Rejection Ratio (dB) Output Voltage (V) VCM (V) (V-) + 0.5 V < VCM < (V+) - 1.5 V VSUPPLY = ±2 V 25 20 15 10 5 0 8 (V-) < VCM < (V+) - 1.5 V 7 6 (V-) + 0.5 V < VCM < (V+) - 1.5 V VSUPPLY = ±18 V 5 4 3 2 1 0 -55 -35 -15 5 25 45 65 85 105 125 -55 -35 -15 5 25 45 Temperature (°C) Temperature (°C) Figure 11. Figure 12. 65 85 105 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 125 9 OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. PSRR vs TEMPERATURE 0.1-Hz TO 10-Hz NOISE 5 Typical Units Shown VSUPPLY = ±2 V to ±18 V 0.8 0.6 0.4 50 nV/div Power-Supply Rejection Ratio (mV/V) 1 0.2 0 -0.2 -0.4 -0.6 -0.8 Peak-to-Peak Noise = 250 nV -1 -55 -35 -15 5 25 45 65 85 105 Time (1 s/div) 125 Temperature (°C) Figure 13. Figure 14. INPUT VOLTAGE NOISE SPECTRAL DENSITY vs FREQUENCY THD+N RATIO vs FREQUENCY Total Harmonic Distortion + Noise (%) 0.01 10 -80 VOUT = 1 VRMS BW = 80 kHz 0.001 -100 0.0001 -120 G = +1, RL = 10 kW G = -1, RL = 10 kW 0.00001 1 0.1 1 10 100 1k 10k 10 100k 100 1k Figure 15. Figure 16. THD+N vs OUTPUT AMPLITUDE QUIESCENT CURRENT vs SUPPLY VOLTAGE BW = 80 kHz 0.01 -80 0.001 -100 0.0001 -120 G = +1, RL = 10 kW G = -1, RL = 10 kW -140 1 10 20 0.5 0.48 0.46 0.44 IQ (mA) Total Harmonic Distortion + Noise (%) -60 Total Harmonic Distortion + Noise (dB) 0.1 0.1 0.42 0.4 0.38 0.36 0.34 0.32 Specified Supply-Voltage Range 0.3 0 Output Amplitude (VRMS) 4 8 12 16 20 24 28 32 36 Supply Voltage (V) Figure 17. 10 -140 20k Frequency (Hz) Frequency (Hz) 0.00001 0.01 10k Total Harmonic Distortion + Noise (dB) Voltage Noise Density (nV/ÖHz) 100 Figure 18. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 TYPICAL CHARACTERISTICS (continued) VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. QUIESCENT CURRENT vs TEMPERATURE OPEN-LOOP GAIN AND PHASE vs FREQUENCY 0.5 180 140 VS = ±18 V 0.48 120 VS = ±2 V 0.46 Gain Phase 135 100 0.42 0.4 0.38 90 60 40 0.36 45 20 0.34 Phase (°) 80 Gain (dB) IQ (mA) 0.44 0 0.32 −20 0.3 -55 -35 5 -15 25 45 65 85 105 1 10 100 125 1k 10k 100k Frequency (Hz) 1M 10M 0 100M G001 Temperature (°C) Figure 19. Figure 20. CLOSED-LOOP GAIN vs FREQUENCY OPEN-LOOP GAIN vs TEMPERATURE 3 25 20 VSUPPLY = 4 V, RL = 10 kW VSUPPLY = 36 V, RL = 10 kW 2.5 15 2 AOL (mV/V) Gain (dB) 10 5 0 1.5 1 -5 -10 G = 10 G = +1 G = -1 -15 0.5 0 -20 10k 100k 1M 10M -55 -35 5 -15 Frequency (Hz) 25 45 65 85 105 125 Temperature (°C) Figure 21. Figure 22. OPEN-LOOP OUTPUT IMPEDANCE vs FREQUENCY SMALL-SIGNAL OVERSHOOT vs CAPACITIVE LOAD (100-mV Output Step) 10k 40 RL = 10 kW 35 ROUT = 0 W 30 Overshoot (%) ZO (W) 1k 100 10 ROUT = 25 W 25 ROUT = 50 W 20 15 G = +1 +18 V ROUT 10 Device 1 -18 V 5 RL CL 0 1m 1 10 100 1k 10k 100k 1M 10M 0 Frequency (Hz) 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Figure 23. Figure 24. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 11 OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. SMALL-SIGNAL OVERSHOOT vs CAPACITIVE LOAD (100-mV Output Step) NO PHASE REVERSAL 40 ROUT = 0 W 35 Device ROUT = 50 W 30 25 -18 V 37 VPP Sine Wave (±18.5 V) 5 V/div Overshoot (%) +18 V ROUT = 25 W 20 15 RI = 10 kW 10 RF = 10 kW G = -1 +18 V VIN VOUT ROUT Device 5 CL RL = 10 kW -18 V 0 0 Time (100 ms/div) 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Figure 25. Figure 26. POSITIVE OVERLOAD RECOVERY NEGATIVE OVERLOAD RECOVERY VIN VOUT 20 kW 20 kW +18 V Device 5 V/div 5 V/div 2 kW VOUT VIN -18 V 2 kW +18 V VOUT Device VIN G = -10 -18 V G = -10 VOUT VIN Time (5 ms/div) Time (5 ms/div) Figure 27. Figure 28. SMALL-SIGNAL STEP RESPONSE (100 mV) SMALL-SIGNAL STEP RESPONSE (100 mV) +18 V G = +1 RL = 10 kW CL = 10 pF 20 mV/div 20 mV/div RL = 10 kW CL = 10 pF RI = 2 kW RF = 2 kW +18 V Device Device -18 V RL CL CL -18 V G = -1 Time (20 ms/div) Time (1 ms/div) Figure 29. 12 Figure 30. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 TYPICAL CHARACTERISTICS (continued) VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. LARGE-SIGNAL STEP RESPONSE LARGE-SIGNAL STEP RESPONSE G = +1 RL = 10 kW CL = 10 pF 5 V/div 5 V/div G = -1 RL = 10 kW CL = 10 pF Time (50 ms/div) Time (50 ms/div) Figure 31. Figure 32. LARGE-SIGNAL SETTLING TIME (10-V Positive Step) LARGE-SIGNAL SETTLING TIME (10-V Negative Step) 10 6 4 12-Bit Settling 2 0 -2 (±1/2 LSB = ±0.024%) -4 -6 -8 6 4 12-Bit Settling 2 0 -2 (±1/2 LSB = ±0.024%) -4 -6 -8 -10 -10 0 10 20 30 40 50 60 0 10 20 30 Time (ms) Time (ms) Figure 33. Figure 34. SHORT-CIRCUIT CURRENT vs TEMPERATURE 40 50 60 MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 30 15 20 12.5 Output Voltage (VPP) VS = ±15 V 10 ISC (mA) G = -1 8 D From Final Value (mV) D From Final Value (mV) 10 G = -1 8 ISC, Source 0 ISC, Sink -10 -20 10 Maximum output voltage without slew-rate induced distortion. 7.5 VS = ±5 V 5 2.5 -30 VS = ±2.25 V 0 -55 -35 -15 5 25 45 65 85 105 125 1k 10k 100k 1M 10M Frequency (Hz) Temperature (°C) Figure 35. Figure 36. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 13 OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. CHANNEL SEPARATION vs FREQUENCY Channel A to B Channel B to A -70 140 -80 120 EMIRR IN+ (dB) Channel Separation (dB) EMIRR IN+ vs FREQUENCY 160 -60 -90 -100 -110 -120 80 60 40 -130 20 -140 -150 1 14 100 10 100 1k 10k 100k 1M 10M 100M 0 10M 100M Frequency (Hz) Frequency (Hz) Figure 37. Figure 38. Submit Documentation Feedback 1G 10G Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 APPLICATION INFORMATION The OPA2188 operational amplifier combines precision offset and drift with excellent overall performance, making the device ideal for many precision applications. The precision offset drift of only 0.085 µV per degree Celsius provides stability over the entire temperature range. In addition, the device offers excellent overall performance with high CMRR, PSRR, and AOL. As with all amplifiers, applications with noisy or high-impedance power supplies require decoupling capacitors close to the device pins. In most cases, 0.1-µF capacitors are adequate. OPERATING CHARACTERISTICS The OPA2188 is specified for operation from 4 V to 36 V (±2 V to ±18 V). Many of the specifications apply from –40°C to +105°C. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in the Typical Characteristics. EMI REJECTION The OPA2188 uses integrated electromagnetic interference (EMI) filtering to reduce the effects of EMI interference from sources such as wireless communications and densely populated boards with a mix of analog signal chain and digital components. EMI immunity can be improved with circuit design techniques; the OPAx188 benefits from these design improvements. Texas Instruments has developed the ability to accurately measure and quantify the immunity of an operational amplifier over a broad frequency spectrum extending from 10 MHz to 6 GHz. Figure 39 shows the results of this testing on the OPA2188. Detailed information can also be found in the Application Report EMI Rejection Ratio of Operational Amplifiers (SBOA128), available for download from the TI website. 160 140 EMIRR IN+ (dB) 120 100 80 60 40 20 0 10M 100M 1G 10G Frequency (Hz) Figure 39. EMIRR Testing Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 15 OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com GENERAL LAYOUT GUIDELINES For best operational performance of the device, good printed circuit board (PCB) layout practices are recommended. Low-loss, 0.1-µF bypass capacitors should be connected between each supply pin and ground, placed as close to the device as possible. A single bypass capacitor from V+ to ground is applicable to singlesupply applications. PHASE-REVERSAL PROTECTION The OPA2188 has an internal phase-reversal protection. Many op amps exhibit a phase reversal when the input is driven beyond its linear common-mode range. This condition is most often encountered in noninverting circuits when the input is driven beyond the specified common-mode voltage range, causing the output to reverse into the opposite rail. The OPA2188 input prevents phase reversal with excessive common-mode voltage. Instead, the output limits into the appropriate rail. This performance is shown in Figure 40. +18 V Device 5 V/div -18 V 37 VPP Sine Wave (±18.5 V) VIN VOUT Time (100 ms/div) Figure 40. No Phase Reversal CAPACITIVE LOAD AND STABILITY The dynamic characteristics of the OPA2188 have been optimized for a range of common operating conditions. The combination of low closed-loop gain and high capacitive loads decreases the phase margin of the amplifier and can lead to gain peaking or oscillations. As a result, heavier capacitive loads must be isolated from the output. The simplest way to achieve this isolation is to add a small resistor (for example, ROUT equal to 50 Ω) in series with the output. Figure 41 and Figure 42 illustrate graphs of small-signal overshoot versus capacitive load for several values of ROUT. Also, refer to the Applications Report, Feedback Plots Define Op Amp AC Performance (SBOA015), available for download from the TI website, for details of analysis techniques and application circuits. 40 40 RL = 10 kW ROUT = 0 W 35 35 ROUT = 0 W ROUT = 25 W 25 ROUT = 50 W 20 15 G = +1 +18 V ROUT 10 ROUT = 50 W -18 V 25 20 15 RI = 10 kW 10 Device 5 ROUT = 25 W 30 Overshoot (%) Overshoot (%) 30 RL G = -1 +18 V ROUT CL Device 5 CL RL = 10 kW -18 V 0 0 0 100 200 300 400 500 600 700 800 900 1000 0 Capacitive Load (pF) 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Figure 41. Small-Signal Overshoot versus Capacitive Load (100-mV Output Step) 16 RF = 10 kW Figure 42. Small-Signal Overshoot versus Capacitive Load (100-mV Output Step) Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 ELECTRICAL OVERSTRESS Designers often ask questions about the capability of an operational amplifier to withstand electrical overstress. These questions tend to focus on the device inputs, but may involve the supply voltage pins or even the output pin. Each of these different pin functions have electrical stress limits determined by the voltage breakdown characteristics of the particular semiconductor fabrication process and specific circuits connected to the pin. Additionally, internal electrostatic discharge (ESD) protection is built into these circuits to protect them from accidental ESD events both before and during product assembly. These ESD protection diodes also provide in-circuit, input overdrive protection, as long as the current is limited to 10 mA as stated in the Absolute Maximum Ratings. Figure 43 shows how a series input resistor may be added to the driven input to limit the input current. The added resistor contributes thermal noise at the amplifier input and its value should be kept to a minimum in noise-sensitive applications. V+ IOVERLOAD 10 mA max VIN 5 kW VOUT Device Figure 43. Input Current Protection An ESD event produces a short duration, high-voltage pulse that is transformed into a short duration, highcurrent pulse as it discharges through a semiconductor device. The ESD protection circuits are designed to provide a current path around the operational amplifier core to prevent it from being damaged. The energy absorbed by the protection circuitry is then dissipated as heat. When the operational amplifier connects into a circuit, the ESD protection components are intended to remain inactive and not become involved in the application circuit operation. However, circumstances may arise where an applied voltage exceeds the operating voltage range of a given pin. Should this condition occur, there is a risk that some of the internal ESD protection circuits may be biased on, and conduct current. Any such current flow occurs through ESD cells and rarely involves the absorption device. If there is an uncertainty about the ability of the supply to absorb this current, external zener diodes may be added to the supply pins. The zener voltage must be selected such that the diode does not turn on during normal operation. However, its zener voltage should be low enough so that the zener diode conducts if the supply pin begins to rise above the safe operating supply voltage level. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 17 OPA2188 SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 www.ti.com APPLICATION EXAMPLES The application examples of Figure 44 and Figure 45 highlight only a few of the circuits where the OPA2188 can be used. 15 V U2 1/2 OPA2188 VOUTP 3.3 V VDIFF/2 -15 V R5 1 kW Ref 1 Ref 2 RG 500 W + VCM 10 R7 1 kW U1 INA159 VOUT Sense -15 V -VDIFF/2 U5 1/2 OPA2188 VOUTN 15 V Figure 44. Discrete INA + Attenuation for ADC with 3.3-V Supply +15 V (5 V) Out REF5050 In 1 mF 1 mF R2 49.1 kW R3 60.4 kW R1 4.99 kW 1/2 OPA2188 VOUT 0°C = 0 V 200°C = 5 V R5 (1) 105.8 kW RTD Pt100 R4 1 kW (1) R5 provides positive-varying excitation to linearize output. Figure 45. RTD Amplifier with Linearization 18 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 OPA2188 www.ti.com SBOS525B – AUGUST 2011 – REVISED SEPTEMBER 2012 REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision A (June 2012) to Revision B • Page Changed second to last Applications bullet .......................................................................................................................... 1 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Links: OPA2188 19 PACKAGE OPTION ADDENDUM www.ti.com 18-Oct-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) OPA2188AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 105 (2188 ~ OPA2188) OPA2188AIDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU | CU NIPDAUAG Level-2-260C-1 YEAR -40 to 105 2188 OPA2188AIDGKT ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAU | CU NIPDAUAG Level-2-260C-1 YEAR -40 to 105 2188 OPA2188AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 105 (2188 ~ OPA2188) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 18-Oct-2013 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 27-Aug-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant OPA2188AIDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2188AIDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2188AIDGKT VSSOP DGK 8 250 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2188AIDGKT VSSOP DGK 8 250 177.8 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2188AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 27-Aug-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2188AIDGKR VSSOP DGK 8 2500 366.0 364.0 50.0 OPA2188AIDGKR VSSOP DGK 8 2500 358.0 335.0 35.0 OPA2188AIDGKT VSSOP DGK 8 250 366.0 364.0 50.0 OPA2188AIDGKT VSSOP DGK 8 250 223.0 270.0 35.0 OPA2188AIDR SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated