CY29FCT520T MULTILEVEL PIPELINE REGISTER WITH 3-STATE OUTPUTS SCCS011C – MAY 1994 – REVISED NOVEMBER 2001 D D D D D D D D D D D D D, P, OR SO PACKAGE (TOP VIEW) Function, Pinout, and Drive Compatible With FCT, F Logic, and AM29520 Reduced VOH (Typically = 3.3 V) Version of Equivalent FCT Functions Edge-Rate Control Circuitry for Significantly Improved Noise Characteristics Ioff Supports Partial-Power-Down Mode Operation Matched Rise and Fall Times Fully Compatible With TTL Input and Output Logic Levels ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 200-V Machine Model (A115-A) – 1000-V Charged-Device Model (C101) Single- and Dual-Pipeline Operation Modes Multiplexed Data Inputs and Outputs CY29FCT520T – 64-mA Output Sink Current 32-mA Output Source Current CY29FCT520ATDMB, CY29FCT520BTDMB – 32-mA Output Sink Current 12-mA Output Source Current 3-State Outputs I0 I1 D0 D1 D2 D3 D4 D5 D6 D7 CLK GND 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VCC S0 S1 Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 OE description The CY29FCT520T is a multilevel 8-bit-wide pipeline register. The device consists of four registers, A1, A2, B1, and B2, which are configured by the instruction inputs I0, I1 as a single four-level pipeline or as two two-level pipelines. The contents of any register can be read at the multiplexed output at any time by using the multiplex-selection controls (S0 and S1). The pipeline registers are positive-edge triggered, and data is shifted by the rising edge of the clock input. Instruction I = 0 selects the four-level pipeline mode. Instruction I = 1 selects the two-level B pipeline, while I = 2 selects the two-level A pipeline. I = 3 is the hold instruction; no shifting is performed by the clock in this mode. In the two-level operation mode, data is shifted from level 1 to level 2 and new data is loaded into level 1. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 CY29FCT520T MULTILEVEL PIPELINE REGISTER WITH 3-STATE OUTPUTS SCCS011C – MAY 1994 – REVISED NOVEMBER 2001 PIPELINE INSTRUCTION TABLE I=1 I=0 I1 = 0 I0 = 0 A1 B1 A2 B2 I=2 I=3 I1 = 0 I0 = 1 I1 = 1 I0 = 0 A1 B1 A1 B1 A2 B2 A2 B2 Single four-level I1 = 1 I0 = 1 A1 B1 A2 B2 Dual two-level Hold ORDERING INFORMATION SOIC – SO –40°C to 85°C SOIC – SO DIP – P SOIC – SO 55°C to 125°C –55°C SPEED (ns) ORDERABLE PART NUMBER Tube 6.0 CY29FCT520CTSOC Tape and reel 6.0 CY29FCT520CTSOCT Tube 7.5 CY29FCT520BTSOC Tape and reel 7.5 CY29FCT520BTSOCT Tube 14.0 CY29FCT520ATPC Tube 14.0 CY29FCT520ATSOC Tape and reel 14.0 CY29FCT520ATSOCT Tube 8.0 5962-9220504MLA (CY29FCT520BTDMB) Tube 16.0 5962-9220502MLA (CY29FCT520ATDMB) PACKAGE† TA CDIP – D TOP-SIDE MARKING 29FCT520C 29FCT520B CY29FCT520ATPC 29FCT520A † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE INPUTS 2 OUTPUT S1 1 S0 1 1 0 A2 0 1 B1 0 0 B2 POST OFFICE BOX 655303 A1 • DALLAS, TEXAS 75265 CY29FCT520T MULTILEVEL PIPELINE REGISTER WITH 3-STATE OUTPUTS SCCS011C – MAY 1994 – REVISED NOVEMBER 2001 logic diagram D0–D7 8 Instruction Register Controls I0 I1 MUX MUX CLK Multiplex Selection S0 S1 Octal Register A1 Octal Register B1 Octal Register A2 Octal Register B2 MUX OE 8 Y0–Y7 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range to ground potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V DC input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V DC output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V DC output current (maximum sink current/pin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 mA Package thermal impedance, θJA (see Note 1): P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W (see Note 2): SO package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46°C/W Ambient temperature range with power applied, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 135°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The package thermal impedance is calculated in accordance with JESD 51-3. 2. The package thermal impedance is calculated in accordance with JESD 51-7. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 CY29FCT520T MULTILEVEL PIPELINE REGISTER WITH 3-STATE OUTPUTS SCCS011C – MAY 1994 – REVISED NOVEMBER 2001 recommended operating conditions (see Note 3) CY29FCT520ATDMB CY29FCT520BTDMB CY29FCT520T UNIT MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.75 5 5.25 VCC VIH Supply voltage VIL IOH Low-level input voltage 0.8 0.8 V High-level output current –12 –32 mA IOL TA Low-level output current 32 64 mA 85 °C High-level input voltage 2 Operating free-air temperature 2 –55 125 V V –40 NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER CY29FCT520ATDMB CY29FCT520BTDMB TEST CONDITIONS MIN VIK VOH VCC = 4.5 V, VCC = 4.75 V, IIN = –18 mA IIN = –18 mA VCC = 4.5 V, IOH = –12 mA IOH = –15 mA VCC = 4 4.75 75 V TYP† MAX –0.7 –1.2 2.4 2.4 IOH = –32 mA IOL = 32 mA Vhys All inputs II VCC = 5.5 V, VCC = 5.25 V, VIN = VCC VIN = VCC 5 IIH VCC = 5.5 V, VCC = 5.25 V, VIN = 2.7 V VIN = 2.7 V ±1 IIL VCC = 5.5 V, VCC = 5.25 V, VIN = 0.5 V VIN = 0.5 V ±1 VCC = 0 V, VCC = 5.5 V, VOUT = 4.5 V VOUT = 0 V ±1 VCC = 5.25 V, VCC = 5.5 V, VOUT = 0 V VIN = 2.7 V VCC = 5.25 V, VCC = 5.5 V, VIN = 2.7 V VIN = 0.5 V VCC = 5.25 V, VCC = 5.5 V, VIN = 0.5 V VIN ≤ 0.2 V, IOZH IOZL ICC ∆ICC UNIT TYP† MAX –0.7 –1.2 V V 3.3 2 VOL IOS‡ MIN 3.3 VCC = 4.5 V, VCC = 4.75 V, Ioff CY29FCT520T 0.3 0.55 IOL = 64 mA 0.3 0.2 0.55 0.2 V 5 ±1 ±1 –60 –120 ±1 –225 –60 –120 –225 10 10 –10 –10 VIN ≥ VCC – 0.2 V VCC = 5.25 V, VIN ≤ 0.2 V, VIN ≥ VCC – 0.2 V VCC = 5.5 V, VIN = 3.4 V§, f1 = 0, Outputs open VCC = 5.25 V, VIN = 3.4 V§, f1 = 0, Outputs open 0.1 0.5 V 0.2 0.1 0.2 0.5 2 2 µA µA µA µA mA µA µA mA mA † Typical values are at VCC = 5 V, TA = 25°C. ‡ Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or sample-and-hold techniques are preferable to minimize internal chip heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output can raise the chip temperature well above normal and cause invalid readings in other parametric tests. In any sequence of parameter tests, IOS tests should be performed last. § Per TTL-driven input (VIN = 3.4 V); all other inputs at VCC or GND 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 CY29FCT520T MULTILEVEL PIPELINE REGISTER WITH 3-STATE OUTPUTS SCCS011C – MAY 1994 – REVISED NOVEMBER 2001 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) (continued) PARAMETER CY29FCT520ATDMB CY29FCT520BTDMB TEST CONDITIONS MIN ICCD¶ VCC = 5.5 V, Outputs open, One bit switching at 50% duty cycle, OE = GND, VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V VCC = 5.25 V, Outputs open, One bit switching at 50% duty cycle, OE = GND, VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V VCC = 5.5 V, Out uts o en, Outputs open f0 = 10 MHz, OE = GND IC# VCC = 5.25 V, Out uts o en, Outputs open f0 = 10 MHz, OE = GND One bit switching at f1 = 5 MHz at 50% duty cycle Eight bits switching at f1 = 5 MHz at 50% duty cycle One bit switching at f1 = 5 MHz at 50% duty cycle Eight bits switching at f1 = 5 MHz at 50% duty cycle TYP† MAX 0.06 0.12 CY29FCT520T MIN TYP† UNIT MAX mA/ MHz 0.06 0.12 VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V 0.7 1.4 VIN = 3.4 V or GND 1.2 3.4 VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V 2.8 5.6|| VIN = 3.4 V or GND 5.1 14.3|| VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V 0.7 1.4 VIN = 3.4 V or GND 1.2 3.4 VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V 2.8 5.6|| VIN = 3.4 V or GND 5.1 14.3|| Ci Co † Typical values are at VCC = 5 V, TA = 25°C. ¶ This parameter is derived for use in total power-supply calculations. # IC = ICC + ∆ICC × DH × NT + ICCD (f0/2 + f1 × N1) Where: IC = Total supply current ICC = Power-supply current with CMOS input levels ∆ICC = Power-supply current for a TTL high input (VIN = 3.4 V) DH = Duty cycle for TTL inputs high NT = Number of TTL inputs at DH ICCD = Dynamic current caused by an input transition pair (HLH or LHL) f0 = Clock frequency for registered devices, otherwise zero f1 = Input signal frequency N1 = Number of inputs changing at f1 All currents are in milliamperes and all frequencies are in megahertz. || Values for these conditions are examples of the ICC formula. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mA 5 10 5 10 pF 9 12 9 12 pF 5 CY29FCT520T MULTILEVEL PIPELINE REGISTER WITH 3-STATE OUTPUTS SCCS011C – MAY 1994 – REVISED NOVEMBER 2001 timing requirements over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) CY29FCT520ATDMB MIN tw Pulse duration, CLK high or low tsu S t time, Setup ti before b f CLK↑ th Hold time, time after CLK↑ CY29FCT520BTDMB MAX MIN 8 6 Data 6 2.8 I 6 4.5 Data 2 2 I 2 2 MAX UNIT ns ns ns timing requirements over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) CY29FCT520AT MIN tw Pulse duration, CLK high or low tsu S t time, Setup ti before b f CLK↑ th Hold time, time after CLK↑ MAX CY29FCT520BT MIN MAX CY29FCT520CT MIN 7 5.5 5.5 Data 5 2.5 2.5 I 5 4 4 Data 2 2 2 I 2 2 2 MAX UNIT ns ns ns switching characteristics over operating free-air temperature range (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL CLK Y tPLH tPHL S0 or S1 Y tPHZ tPLZ OE Y tPZH tPZL OE Y CY29FCT520ATDMB CY29FCT520BTDMB MIN MAX MIN MAX 2 16 2 8 2 16 2 8 2 15 2 8 2 15 2 8 1.5 13 1.5 7.5 1.5 13 1.5 7.5 1.5 16 1.5 8 1.5 16 1.5 8 UNIT ns ns ns ns switching characteristics over operating free-air temperature range (see Figure 1) 6 PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL CLK Y tPLH tPHL S0 or S1 Y tPHZ tPLZ OE Y tPZH tPZL OE Y POST OFFICE BOX 655303 CY29FCT520AT CY29FCT520BT CY29FCT520CT MIN MAX MIN MAX MIN MAX 2 14 2 7.5 2 6 2 14 2 7.5 2 6 2 13 2 7.5 2 6 2 13 2 7.5 2 6 1.5 12 1.5 7 1.5 6 1.5 12 1.5 7 1.5 6 1.5 15 1.5 7.5 1.5 6 1.5 15 1.5 7.5 1.5 6 • DALLAS, TEXAS 75265 UNIT ns ns ns ns CY29FCT520T MULTILEVEL PIPELINE REGISTER WITH 3-STATE OUTPUTS SCCS011C – MAY 1994 – REVISED NOVEMBER 2001 PARAMETER MEASUREMENT INFORMATION 7V From Output Under Test From Output Under Test Test Point CL = 50 pF (see Note A) Open TEST GND CL = 50 pF (see Note A) 500 Ω S1 500 Ω S1 Open 7V Open tPLH/tPHL tPLZ/tPZL tPHZ/tPZH 500 Ω LOAD CIRCUIT FOR 3-STATE OUTPUTS LOAD CIRCUIT FOR TOTEM-POLE OUTPUTS 3V 1.5 V Timing Input 0V tw tsu 3V 1.5 V Input 1.5 V th 3V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.5 V Input 1.5 V 0V tPLH tPHL 1.5 V 1.5 V VOL tPHL Out-of-Phase Output tPLZ ≈3.5 V 1.5 V tPZH VOH 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V Output Waveform 1 (see Note B) tPLH 1.5 V 1.5 V tPZL VOH In-Phase Output 3V Output Control Output Waveform 2 (see Note B) VOL + 0.3 V VOL tPHZ 1.5 V VOH – 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 PACKAGE OPTION ADDENDUM www.ti.com 15-Apr-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) 5962-9220502MLA ACTIVE CDIP JT 24 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9220502ML A 5962-9220504MLA ACTIVE CDIP JT 24 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9220504ML A CY29FCT520ATSOC ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 29FCT520A CY29FCT520BTSOC ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 29FCT520B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 15-Apr-2017 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA MCER004A – JANUARY 1995 – REVISED JANUARY 1997 JT (R-GDIP-T**) CERAMIC DUAL-IN-LINE 24 LEADS SHOWN PINS ** A 13 24 B 1 24 28 A MAX 1.280 (32,51) 1.460 (37,08) A MIN 1.240 (31,50) 1.440 (36,58) B MAX 0.300 (7,62) 0.291 (7,39) B MIN 0.245 (6,22) 0.285 (7,24) DIM 12 0.070 (1,78) 0.030 (0,76) 0.100 (2,54) MAX 0.320 (8,13) 0.290 (7,37) 0.015 (0,38) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.014 (0,36) 0.008 (0,20) 0.100 (2,54) 4040110/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP3-T24, GDIP4-T28, and JEDEC MO-058 AA, MO-058 AB POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2017, Texas Instruments Incorporated