ON MC74LVX4245 Dual supply octal translating transceiver with 3−state output Datasheet

MC74LVX4245
Dual Supply Octal
Translating Transceiver
with 3−State Outputs
The 74LVX4245 is a 24−pin dual−supply, octal translating
transceiver that is designed to interface between a 5.0 V bus and a 3.0 V
bus in a mixed 3.0 V / 5.0 V supply environment such as laptop
computers using a 3.3 V CPU and 5.0 V LCD display. The A port
interfaces with the 5V bus; the B port interfaces with the 3.0 V bus.
The Transmit/Receive (T/R) input determines the direction of data
flow. Transmit (active−High) enables data from the A port to the B
port. Receive (active−Low) enables data from the B port to the A port.
The Output Enable (OE) input, when High, disables both A and B
ports by placing them in 3−State.
http://onsemi.com
MARKING
DIAGRAMS
24
24
1
Features
•
•
•
•
•
•
•
•
1
Bi−directional Interface Between 5.0 V and 3.0 V Buses
Control Inputs Compatible with TTL Level
5.0 V Data Flow at A Port and 3.0 V Data Flow at B Port
Outputs Source/Sink 24 mA at 5.0 V Bus and 12 mA at 3.0 V Bus
Guaranteed Simultaneous Switching Noise Level and Dynamic
Threshold Performance
Available in SOIC and TSSOP Packages
Functionally Compatible with the 74 Series 245
Pb−Free Packages are Available*
VCCB VCCB OE
24
1
23
2
VCCA T/R
LVX
4245
AWLYYWW
SOIC−24
DW SUFFIX
CASE 751E
22
B0
B1
B2
B3
B4
B5
B6
B7
GND
21
20
19
18
17
16
15
14
13
3
4
5
6
7
8
9
10
A0
A1
A2
A3
A4
A5
A6
A7
11
24
24
TSSOP−24
DT SUFFIX
CASE 948H
1
LVXC4245
AWLYYWW
1
A
WL
YY
WW
=
=
=
=
Assembly Location
Wafer Lot
Year
Work Week
PIN NAMES
Pins
Function
OE
T/R
A0−A7
Output Enable Input
Transmit/Receive Input
Side A 3−State Inputs or 3−State
Outputs
Side B 3−State Inputs or 3−State
Outputs
B0−B7
12
GND GND
ORDERING INFORMATION
Figure 1. 24−Lead Pinout
(Top View)
See detailed ordering and shipping information in the package
dimensions section on page 5 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
 Semiconductor Components Industries, LLC, 2005
March, 2005 − Rev. 4
1
Publication Order Number:
MC74LVX4245/D
MC74LVX4245
OE 22
T/R 2
A0
3
21
A1
B0
4
20
A2
B1
5
19
A3
B2
6
18
A4
B3
7
17
A5
B4
8
16
A6
B5
9
15
A7
B6
10
14
B7
Figure 2. Logic Diagram
INPUTS
OE
T/R
OPERATING MODE
Non−Inverting
L
L
B Data to A Bus
L
H
A Data to B Bus
H
X
Z
H = High Voltage Level; L = Low Voltage Level; Z = High Impedance State; X = High or Low Voltage Level
and Transitions are Acceptable; For ICC reasons, Do Not Float Inputs
http://onsemi.com
2
MC74LVX4245
ABSOLUTE MAXIMUM RATINGS
Symbol
VCCA,
VCCB
VI
VI/O
Parameter
DC Input Voltage
DC Input Diode Current
IOK
DC Output Diode Current
IO
DC Output Source/Sink Current
DC Supply Current
TSTG
Storage Temperature Range
Unit
V
OE, T/R
−0.5 to VCCA +0.5
V
An
−0.5 to VCCA +0.5
V
Bn
−0.5 to VCCB +0.5
V
OE, T/R
ICC,
IGND
Condition
−0.5 to +7.0
DC Input/Output Voltage
IIK
Latchup
Value
DC Supply Voltage
Per Output Pin
Maximum Current at ICCA
Maximum Current at ICCB
DC Latchup Source/Sink Current
±20
VI < GND
mA
±50
VO < GND; VO > VCC
mA
±50
mA
±50
±200
±100
mA
−65 to +150
°C
±300
mA
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCCA,
VCCB
VI
VI/O
TA
t/V
Parameter
Min
Max
Unit
4.5
2.7
5.5
3.6
V
OE, T/R
0
VCCA
V
An
Bn
0
0
VCCA
VCCB
V
−40
+85
°C
0
8
ns/V
Supply Voltage
VCCA
VCCB
Input Voltage
Input/Output Voltage
Operating Free−Air Temperature
Minimum Input Edge Rate
VIN from 30% to 70% of VCC; VCC at 3.0V, 4.5V, 5.5V
DC ELECTRICAL CHARACTERISTICS
TA = 25°C
Symbol
VIHA
VIHB
VILA
VILB
VOHA
VOHB
VOLA
VOLB
Parameter
Minimum HIGH
Level
I
tV
lt
Input
Voltage
Condition
An,OE
T/R
Bn
Maximum LOW
Level
I
tV
lt
Input
Voltage
An,OE
T/R
Bn
VOUT ≤ 0.1V
or
≥ VCC − 0.1V
VOUT ≤ 0.1V
or
≥ VCC − 0.1V
Typ
TA = −40 to +85°C
VCCA
VCCB
Guaranteed Limits
Unit
5.5
4.5
3.3
3.3
2.0
2.0
2.0
2.0
V
5.0
5.0
3.6
2.7
2.0
2.0
2.0
2.0
V
5.5
4.5
3.3
3.3
0.8
0.8
0.8
0.8
V
5.0
5.0
2.7
3.6
0.8
0.8
0.8
0.8
V
Minimum HIGH
Level
O t tV
lt
Output
Voltage
IOUT = −100A
IOH = −24mA
4.5
4.5
3.0
3.0
4.50
4.25
4.40
3.86
4.40
3.76
V
IOUT = −100A
IOH = −12mA
IOH = −8mA
4.5
4.5
4.5
3.0
3.0
2.7
2.99
2.80
2.50
2.9
2.4
2.4
2.9
2.4
2.4
V
Maximum LOW
Level
O t tV
Output
Voltage
lt
IOUT = 100A
IOL = 24mA
4.5
4.5
3.0
3.0
0.002
0.18
0.10
0.36
0.10
0.44
V
IOUT = 100A
IOL = 12mA
IOL = 8mA
4.5
4.5
4.5
3.0
3.0
2.7
0.002
0.1
0.1
0.10
0.31
0.31
0.10
0.40
0.40
V
http://onsemi.com
3
MC74LVX4245
DC ELECTRICAL CHARACTERISTICS
TA = 25°C
Symbol
IIN
IOZA
IOZB
Parameter
Condition
VCCA
VCCB
OE,
T/R
VI = VCCA, GND
5.5
3.6
±0.1
±1.0
Max 3−State Output Leakage
An
VI = VIH, VIL
OE = VCCA
VO = VCCA, GND
5.5
3.6
±0.5
±5.0
Max 3−State Output Leakage
Bn
VI = VIH, VIL
OE = VCCA
VO = VCCB, GND
5.5
3.6
±0.5
±5.0
VI=VCCA−2.1V
5.5
3.6
1.35
1.5
VI=VCCB−0.6V
5.5
3.6
0.35
0.5
Max Input Leakage
Current
Typ
Guaranteed Limits
ICC
Maximum ICCT
per Input
ICCA
Quiescent VCCA
Supply Current
An=VCCA or GND
Bn=VCCB or GND
OE=GND
T/R=GND
Quiescent VCCB
Supply Current
An=VCCA or GND
Bn=VCCB or GND
OE=GND
T/R=VCCA
5.5
3.6
5
An,OE
T/R
Bn
ICCB
TA = −40 to +85°C
1.0
Unit
A
A
A
mA
mA
A
5.5
3.6
8
80
A
50
VOLPA
VOLPB
Quiet Output Max
Dynamic VOL
Notes 1, 2
5.0
5.0
3.3
3.3
1.5
1.2
V
VOLVA
VOLVB
Quiet Output Min
Dynamic VOL
Notes 1, 2
5.0
5.0
3.3
3.3
−1.2
−0.8
V
VIHDA
VIHDB
Min HIGH Level
Dynamic Input
Voltage
Notes 1, 3
5.0
5.0
3.3
3.3
2.0
2.0
VILDA
VILDB
Max LOW Level
Dynamic Input
Voltage
Notes 1, 3
5.0
5.0
3.3
3.3
0.8
0.8
V
V
1. Worst case package.
2. Max number of outputs defined as (n). Data inputs are driven 0V to VCC level; one output at GND.
3. Max number of data inputs (n) switching. (n−1) inputs switching 0V to VCC level. Input under test switching: VCC level to threshold (VIHD),
0V to threshold (VILD), f = 1MHz.
CAPACITIVE CHARACTERISTICS
Symbol
Parameter
Condition
Typical
Unit
CIN
Input Capacitance
VCCA = 5.0V; VCCB = 3.3V
4.5
pF
CI/O
Input/Output Capacitance
VCCA = 5.0V; VCCB = 3.3V
15
pF
CPD
Power Dissipation Capacitance
(Measured at 10MHz)
VCCA = 5.0V
VCCB = 3.3V
55
40
pF
B→A
A→B
http://onsemi.com
4
MC74LVX4245
AC ELECTRICAL CHARACTERISTICS
Symbol
Parameter
TA = −40 to +85°C
CL = 50pF
TA = −40 to +85°C
CL = 50pF
VCCA = 5V ±0.5V
VCCB = 3.3V ±0.3V
VCCA = 5V ±0.5V
VCCB = 2.7V
Min
Typ
(Note 4)
Max
Min
Max
Unit
tPHL
tPLH
Propagation Delay A to B
1.0
1.0
5.1
5.3
9.0
9.0
1.0
1.0
10.0
10.0
ns
tPHL
tPLH
Propagation Delay B to A
1.0
1.0
5.4
5.5
9.0
9.0
1.0
1.0
10.0
10.0
ns
tPZL
tPZH
Output Enable Time OE to B
1.0
1.0
6.5
6.7
10.5
10.5
1.0
1.0
11.5
11.5
ns
tPZL
tPZH
Output Enable Time OE to A
1.0
1.0
5.2
5.8
9.5
9.5
1.0
1.0
10.0
10.0
ns
tPHZ
tPLZ
Output Disable Time OE to B
1.0
1.0
6.0
3.3
10.0
7.0
1.0
1.0
10.0
7.5
ns
tPHZ
tPLZ
Output Disable Time OE to A
1.0
1.0
3.9
2.9
7.5
7.0
1.0
1.0
7.5
7.5
ns
1.0
1.5
tOSHL
tOSLH
Output to Output Skew, Data to Output (Note 5)
1.5
ns
4. Typical values at VCCA = 5.0V; VCCB = 3.3V at 25°C.
5. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGH−to−LOW (tOSHL) or LOW−to−HIGH (tOSLH); parameter
guaranteed by design.
ORDERING INFORMATION
Package
Shipping†
MC74LVX4245DW
SOIC−24
30 Units / Rail
MC74LVX4245DWR2
SOIC−24
1000 Tape & Reel
MC74LVX4245DWR2G
SOIC−24
(Pb−Free)
1000 Tape & Reel
MC74LVX4245DT
TSSOP−24*
62 Units / Rail
MC74LVX4245DTR2
TSSOP−24*
2500 Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently Pb−Free.
http://onsemi.com
5
MC74LVX4245
Dual Supply Octal Translating Transceiver
The 74LVX4245 is a is a dual−supply device well capable
of bidirectional signal voltage translation. This level shifting
ability provides an excellent interface between low voltage
CPU local bus and a standard 5.0 V I/O bus. The device
control inputs can be controlled by either the low voltage
CPU and core logic or a bus arbitrator with 5.0 V I/O levels.
The LVX4245 is ideal for mixed voltage applications such
as notebook computers using a 3.3 V CPU and 5.0 V
peripheral devices.
LOW VOLTAGE CPU LOCAL BUS
VCCB
VCCB
LVX4245
VCCA
Applications:
Mixed Mode Dual Supply Interface Solutions
LVX4245
VCCA
EISA − ISA − MCA
(5V I/O LEVELS)
The LVX4245 is designed to solve 3.0 V / 5.0 V interfaces
when CMOS devices cannot tolerate I/O levels above their
applied VCC. If an I/O pin of a 3.0 V device is driven by a 5.0
V device, the P−Channel transistor in the 3.0 V device will
conduct − causing current flow from the I/O bus to the 3.0 V
power supply. The result may be destruction of the 3.0 V
device through latchup effects. A current limiting resistor
may be used to prevent destruction, but it causes speed
degradation and needless power dissipation.
A better solution is provided in the LVX4245. It provides
two different output levels that easily handle the dual voltage
interface. The A port is a dedicated 5.0 V port; the B port is
a dedicated 3.0 V port.
Since the LVX4245 is a ‘245 transceiver, the user may
either use it for bidirectional or unidirectional applications.
The center 20 pins are configured to match a ‘245 pinout.
This enables the user to easily replace this level shifter with
a 3.0 V ‘245 device without additional layout work or re−
manufacture of the circuit board (when both buses are 3.0 V).
Figure 3. 3.3V/5V Interface Block Diagram
Powering Up the LVX4245
When powering up the LVX4245, please note that if the
VCCB pin is powered−up well in advance of the VCCA pin,
several milliamps of either ICCA or ICCB current will result.
If the VCCA pin is powered−up in advance of the VCCB pin
then only nanoamps of Icc current will result. In actuality the
VCCB can be powered “slightly” before the VCCA without
the current penalty, but this “setup time” is dependent on the
power−up ramp rate of the VCC pins. With a ramp rate of
approximately 50 mV/ns (50V/s) a 25 ns setup time was
observed (VCCB before VCCA). With a 7.0 V/s rate, the
setup time was about 140ns. When all is said and done, the
safest powerup strategy is to simply power VCCA before
VCCB. One more note: if the VCCB ramp rate is faster than
the VCCA ramp rate then power problems might still occur,
even if the VCCA powerup began prior to the VCCB powerup.
http://onsemi.com
6
MC74LVX4245
5V
MICROCHANNEL/
EISA/ISA/AT
5V BUS
LOCAL
3V BUS
KEYBOARD
CONTROLLER
3V
CACHE
SRAM
SUPER
I/O
5V
VCCA
3V
VCCB
CPU
386/486
CORE
LOGIC
LVX4245
TRANSCEIVERS
A PORT
A0:7
B PORT
B0:7
ROM
BIOS
PCMCIA
CONTROLLER
MEMORY
DRIVER
VGA
CONTROLLER
Figure 4. MC74LVX4245 Fits Into a System with 3V Subsystem and 5V Subsystem
VCCA
MC74LVX4245
(T/R) DIR
VCCB
VCCB
A0
OE
A1
B0
A2
A3
A4
STANDARD
74 SERIES
‘245
B1
B2
B3
A5
B4
A6
B5
A7
B6
GND
B7
GND
GND
Figure 5. MC74LVX4245 Pin Arrangement Is Compatible to 20−Pin 74 Series ‘245s
http://onsemi.com
7
MC74LVX4245
VCC
An, Bn
50% VCC
50% VCC
0V
tPLH
tPHL
50% VCC
Bn, An
VOH
50% VCC
VOL
WAVEFORM 1 − PROPAGATION DELAYS
tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns
VCCA
50% VCC
50% VCC
OE, T/R
0V
tPHZ
tPZH
VCC
VOH − 0.3V
50% VCC
An, Bn
≈ 0V
tPZL
tPLZ
≈ VCC
50% VCC
An, Bn
VOL + 0.3V
GND
WAVEFORM 2 − OUTPUT ENABLE AND DISABLE TIMES
tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns
Figure 6. AC Waveforms
VCC
PULSE
GENERATOR
R1
DUT
RT
CL
TEST
RL
SWITCH
tPLH, tPHL, tPZH, tPHZ
Open
2 × VCC
tPZL, tPLZ
CL = 50pF or equivalent (Includes jig and probe capacitance)
RL = R1 = 500 or equivalent
RT = ZOUT of pulse generator (typically 50)
Figure 7. Test Circuit
http://onsemi.com
8
2 × VCC
OPEN
MC74LVX4245
PACKAGE DIMENSIONS
SOIC−24
DW SUFFIX
CASE 751E−04
ISSUE E
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN
EXCESS OF D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
−A−
24
13
−B−
12X
P
0.010 (0.25)
1
M
B
M
12
24X
D
J
0.010 (0.25)
M
T A
S
B
S
F
R
C
−T−
SEATING
PLANE
M
22X
G
K
http://onsemi.com
9
X 45 DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
15.25
15.54
7.40
7.60
2.35
2.65
0.35
0.49
0.41
0.90
1.27 BSC
0.23
0.32
0.13
0.29
0
8
10.05
10.55
0.25
0.75
INCHES
MIN
MAX
0.601
0.612
0.292
0.299
0.093
0.104
0.014
0.019
0.016
0.035
0.050 BSC
0.009
0.013
0.005
0.011
0
8
0.395
0.415
0.010
0.029
MC74LVX4245
PACKAGE DIMENSIONS
TSSOP−24
DT SUFFIX
CASE 948H−01
ISSUE A
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS. MOLD
FLASH OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT
EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
24X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
S
S
2X
24
L/2
13
B
−U−
L
PIN 1
IDENT.
12
1
0.15 (0.006) T U
S
A
−V−
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
C
0.10 (0.004)
−T− SEATING
PLANE
G
D
H
−W−
MILLIMETERS
MIN
MAX
7.70
7.90
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.27
0.37
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0
8
INCHES
MIN
MAX
0.303
0.311
0.169
0.177
−−−
0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.011
0.015
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0
8
DETAIL E
N
J1
K
0.25 (0.010)
K1
M
ÇÇÇ
ÉÉ
ÇÇÇ
ÉÉ
ÇÇÇ
N
F
SECTION N−N
J
DETAIL E
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
10
For additional information, please contact your
local Sales Representative.
MC74LVX4245/D
Similar pages