RoHS MUR105-MUR160 D T ,. L FEATURES Super fast switching speed. Low leakage. VOLTAGE RANGE CURRENT Low forward voltage. 1250 to 1300 Volts 1.0 Ampere High current capability. High surge capability. .034(0.9) DO-41 DIA. .028(0.7) High temperature soldering guaranteed: o 260 C/10 seconds/0.375 ＂ (9.5mm)lead length 1.0(25.4) MIN at 5 lbs (2,3kg) tension C MECHANICAL DATA Case: Transfer molded plastic .205(5.2) Epoxy: UL94V-0 rate flame retardant .165(4.2) IC Polarity: Color band denotes cathode end Lead: Plated axial lead ,solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.041 ounce,0.39 gram O .107(2.7) DIA .080(2.0) 1.0(25.4) N MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o O MIN Dimensions in inches and (millimeters) Ratings at 25 C ambient temperature unless otherwise specified. R T Single phase,half wave,60Hz,resistive or inductive load. For capacitive load derate current by 20%. C E L Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage SYMBOLS MUR105 MUR110 MUR115 MUR120 MUR140 MUR160 V RRM 50 100 150 200 300 400 V olts V RMS 35 50 70 105 140 210 280 V olts 100 150 200 300 400 V olts V DC Maximum Average Forward Rectified Current o 0.375”(9.5mm)Lead length at T A=55 C I (AV) 1.0 Peak Forward Surge Current 8.3ms single half sine-wave superimposed on I FSM 35 J E E UNITS A mps A mps rated load (JEDEC Method) Maximum Instantaneous Forward Voltage Drop at 1.0A Maximum DC Reverse Current at rated DC blocking voltage per element W VF 0.95 o T A =25 C o t rr Typical Junction Capacitance(NOTE2) CJ Typical Thermal Resistance(NOTE3). Operating and Storage Temperature Range R JA T J ,T STG V olts 5.0 50 IR T A =125 C Maximum Reverse Recovery Time(NOTE 1) 1.25 A 35 nS 20 30 40 -65 to +150 pF O C/W NOTES: 1.Test condition:I F=0.5A,I R=1.0A.I RR=0.25A. 2.Measured at 1MHz and applied reverse of 4.0volts. 3.Thermal resistance from junction to ambient with 0.375”(9.5mm) lead length,P.C.B.mounted. WEJ ELECTRONIC CO. Http:// www.wej.cn E-mail:[email protected] O C RoHS MUR105-MUR160 FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE FORWARD SURGE CURRENT 80 (A) Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375 ＂(9.5mm) Lead Length 0 0 25 50 55 75 100 125 150 8.3ms Single Half Sine-Wave 50 40 30 20 175 10 o AMBIENT TEMPERATURE,( C) R T o T j=25 C Pulse Width=300us 1% Duty Cycle C E L O MUR105-MUR120 MUR140-MUR160 0.001 0.4 0.6 0.8 1.0 E 1.2 1.4 2 J E 1.6 N 10 20 40 60 100 CHARACTERISTICS o Tj=100 C 1.0 0.1 o T j=25 C 0.01 0 20 40 60 80 100 120 140 REVERSE VOLTAGE,(%) FIG.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC MUR105-MUR120 MUR140-MUR160 50 NONINDUCTIVE +0.5A 10 NONINDUCTIVE Trr (-) (+) D.U.T. 25 Vdc (approx.) PULSE GENERATIOR (NOTE 2) (+) (-) 1 NON INDUCTIVE 1.0 0 -0.25A OSCILLOSCOPE (NOTE 1) o Tj=25 C f=1MHz Vsig=50mVp-p 0.1 8 PERCENT OF RATED PEAK 10 1 O 10 1.8 FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE,(pF) 6 FIG.4-TYPICAL REVERSE INSTANTANEOUS FORWARD VOLTAGE,(V) 100 C 4 (uA) (A) 1.0 0.01 1 IC FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 0.1 1 Cycle NUMBER OF CYCLES AT 60 Hz INSTANTANEOUS REVERSE CURRENT, INSTANTANEOUS FORWARD CURRENT, 10 (JEDEC Method) T j=Tjmax 60 CURRENT,(A) 2.0 1.0 70 PEAK FORWARD SURGE AVERAGE FORWARD CURRENT, 30. W D T ,. L FIG.2-MAXIMUM NON-REPETITIVE PEAK -1.0A 10 100 NOTES: 1.Rise Time=7ns max.Input Impedance= 1 megohm.22pF 2.Rise time=10ns max.Source Impedance= 50 ohms 1cm SET TIME BASE FOR 50/100ns/cm REVRESE VOLTAGE,(V) WEJ ELECTRONIC CO. Http:// www.wej.cn E-mail:[email protected]