Ordering information Rugged PCB type LEB100F LEB 100 1 2 F 3 -05 Recommended Noise Filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series *The Noise Filter is recommended *to connect with several devices. MODEL V1 V2 DC OUTPUT LEB100F-0512 +5V 5A +12V 5(Peak 10)A LEB100F-0324 +3.3V 5A +24V 4(Peak 7)A LEB100F-0524 +5V 5A +24V 4(Peak 7)A 24 4 5 -O 6 1Series name 2Output wattage 3Universal input 4V1 Output voltage 5V2 Output voltage 6Optional *1 G :Low leakage current R :with Remote ON/OFF S :with Chassis SN :with Chassis & cover T :Vertical terminal block Y :with Potentiometer Z :with ZT LEB100F-0530 +5V 5A +30V 3.2(Peak 5.6)A LEB100F-0536 +5V 5A +36V 2.7(Peak 4.7)A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT LEB OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 *3 *4 ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] *2 TOTAL OUTPUT WATTAGE[W] *3 LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *4 RIPPLE[mVp-p] -10 - 0C *4 0 to +50C *4 RIPPLE NOISE[mVp-p] -10 - 0C *4 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C DRIFT[mV] *5 START-UP TIME[ms] *6 HOLD-UP TIME[ms] *6 OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] V1 OVERCURRENT PROTECTION V2 V1 OVERVOLTAGE PROTECTION V2 REMOTE ON/OFF INPUT-OUTPUT -RC *7 INPUT-FG OUTPUT-RC-FG *7 OUTPUT-OUTPUT(V1 -RC-V2) *7 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LEB100F-0512 LEB100F-0324 LEB100F-0524 LEB100F-0530 AC85 - 264 1f or DC 120 - 370 1.2typ (Io=100%) 1.4typ (Io=100%) 0.6typ (Io=100%) 0.7typ (Io=100%) 50/60 (47 - 63) or DC 74typ (Io=100%) 78typ (Io=100%) 78typ (Io=100%) 78typ (Io=100%) 76typ (Io=100%) 80typ (Io=100%) 80typ (Io=100%) 80typ (Io=100%) 0.98typ 0.99typ 0.93typ 15typ (Io=100%) (At cold start) (Ta=25 C) 30typ (Io=100%) (At cold start) (Ta=25 C) 0.75max (60Hz, According to IEC60950 and DEN-AN) +5 +12 +3.3 +24 +5 +24 +5 +30 0-5 0 - 5 (Peak 10) 0 - 5 0 - 4 (Peak 7) 0 - 5 0 - 4 (Peak 7) 0 - 5 0 - 3.2 (Peak 5.6) 85 (Peak 145) 100 (Peak 172) 100 (Peak 172) 100 (Peak 172) 20max 48max 20max 96max 20max 96max 20max 120max 40max 100max 40max 150max 40max 150max 40max 180max 80max 120max 80max 120max 80max 120max 80max 200max 140max 160max 140max 160max 140max 160max 140max 240max 120max 150max 120max 150max 120max 150max 120max 300max 160max 180max 160max 180max 160max 180max 160max 360max 50max 120max 50max 240max 50max 240max 50max 300max 60max 150max 60max 290max 60max 290max 60max 350max 20max 48max 20max 96max 20max 96max 20max 120max 250max 500max 250max 500max 250max 500max 250max 500max 40typ 20typ 40typ 20typ 40typ 20typ 40typ 20typ 4.5 - 5.5 Fixed 2.85 - 3.60 Fixed 4.5 - 5.5 Fixed 4.5 - 5.5 Fixed 11.5 - 12.5 xx 23.0 - 25.0 xx 23.0 - 25.0 xx 28.7 - 31.5 xx Works over 105% of rating current and recovers automatically Works over 101% of peak current and recovers automatically Works over 115% of rating, by zener diode clamping Works at 115 - 140% of rating Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL, EN60950-1, EN50178 Complies with DEN-AN and IEC60950-1 (At only AC input) Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B Complies with IEC61000-3-2 75X35X222mm (WXHXD) /420g max (without chassis and cover) Convection Specification is changed at option, refer to Instruction Manual 5. Peak loading for 10sec. And Duty 35% max, refer to Instruction Manual 4. In detail. Refer to Instruction Manual 2.2 in detail. This is the value that measured on measuring board with capacitor of 22mF within 150mm from output terminal.Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM101). *5 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, F-2 *6 *7 * * * with the input voltage held constant at the rated input/output. ACIN 100V,lo=100% Applicable when remote control (optional) is added. Series/Parallel operation is not possible. Derating is required when operated with chassis and cover. A sound may occur from power supply at peak loading. LEB100F-0536 78typ (Io=100%) 80typ (Io=100%) +5 +36 0-5 0 - 2.7 (Peak 4.7) 100 (Peak 172) 20max 144max 40max 180max 80max 200max 140max 240max 120max 300max 160max 360max 50max 300max 60max 350max 20max 144max 250max 500max 40typ 20typ 4.5 - 5.5 Fixed 34.5 - 37.5 xx LEB100F External view CN1 CN2 4.5 85 25-+0.5 4 5 8 (17) CN3 Voltage adjust(V1) Connector for Remote ON/OFF (option) Connector for -Z (option) (197) 212 -+ 0.5 CN4 222 252 º4.5 235-+0.5 2-M4 Mounting Hole 8 3max CN3 20 (Lead) CN4 RC(-) PCB t=1.6 15 4.5 32 CN3 46 CN4 5 4-M4 Mounting Hole 8 42 20 1 G2 +V2 G1 +V1 C119 FG AC(N) AC(L) 45-+0.5 65-+0.5 5 3 1 5 RC(+) + COM - PIN CONNECTION I / O Connector Mating Connector Terminal Chain : SVH-21T-P1.1 CN1 VHR-5N B3P5-VH Loose: BVH-21T-P1.1 Chain : SVH-21T-P1.1 CN2 VHR-8N B8P-VH Loose: BVH-21T-P1.1 Chain : SXH-001T-P0.6 CN3 XHP-2 (Option) B2B-XH-A Loose: BXH-001T-P0.6 Chain : SXH-001T-P0.6 CN4 XHP-3 (Option) B3B-XH-A Loose: BXH-001T-P0.6 (Mfr: J.S.T.) CN1 Pin No. Input 1 AC(L) 2 3 AC(N) 4 5 FG CN3 (Option) Pin No. Remote ON/OFF 1 RC(+) 2 RC(-) CN2 Pin No. Output G2 1, 2 V2 3, 4 G1 5, 6 V1 7, 8 ¶Weight: 420g or less (Without chassis and cover) ¶Tolerance: t1 ¶Dimensions in mm. ¶PCB Material : CEM3 ¶Chassis and cover is optional. ¶Mounting torque: 1.5N · m(16kgf · cm)max CN4 (Option) Pin No. -Z 1 + COM 2 3 ¶Keep drawing current per pin below 5A for CN2 Performance data LEB ¡RISE TIME & FALL TIME (LEB100F-0524) ¡EFFICIENCY (LEB100F-0524) 82 +24V 80 ACIN 100V Io=100% DC Output EFFICIENCY 78 +5V 76 74 AC Input 72 100ms/DIV 70 60 20ms/DIV ¡INPUT HARMONIC CURRENT (LEB100F-0524) 100 140 180 220 260 300 V ¡INPUT HARMONIC CURRENT (LEB100F-0524) 10 HARMONIC CURRENT Load factor 100% Input voltage AC 100V 1 0.1 0.01 10 20 30 Harmonic current standard class A (at odd number) A A Harmonic current standard class A (at odd number) 0.001 0 Load factor100% Load factor 50% INPUT VOLTAGE 10 HARMONIC CURRENT 75 CN2 CN1 235-+0.5 2-º4.5 4-º3.5 Mounting Hole 30 Name plate 1 Load factor 100% Input voltage AC 230V 0.1 0.01 0.001 0 40 HARMONIC ORDER 10 20 Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ Änderungen vorbehalten / subject to change without notice 30 40 HARMONIC ORDER ■ ■ ■ F-3