NXP MK10DX256ZVLQ10 K10 sub-family Datasheet

Freescale Semiconductor
Data Sheet: Technical Data
K10 Sub-Family Data Sheet
Document Number: K10P144M100SF2
Rev. 7, 02/2013
K10P144M100SF2
Supports the following:
MK10DX128ZVLQ10,
MK10DX128ZVMD10,
MK10DX256ZVLQ10,
MK10DX256ZVMD10,
MK10DN512ZVLQ10,
MK10DN512ZVMD10
Features
• Operating Characteristics
– Voltage range: 1.71 to 3.6 V
– Flash write voltage range: 1.71 to 3.6 V
– Temperature range (ambient): -40 to 105°C
• Performance
– Up to 100 MHz ARM Cortex-M4 core with DSP
instructions delivering 1.25 Dhrystone MIPS per
MHz
• Memories and memory interfaces
– Up to 512 KB program flash memory on nonFlexMemory devices
– Up to 128 KB RAM
– Serial programming interface (EzPort)
– FlexBus external bus interface
• Clocks
– 3 to 32 MHz crystal oscillator
– 32 kHz crystal oscillator
– Multi-purpose clock generator
• System peripherals
– Multiple low-power modes to provide power
optimization based on application requirements
– Memory protection unit with multi-master
protection
– 16-channel DMA controller, supporting up to 63
request sources
– External watchdog monitor
– Software watchdog
– Low-leakage wakeup unit
• Security and integrity modules
– Hardware CRC module to support fast cyclic
redundancy checks
– 128-bit unique identification (ID) number per chip
• Human-machine interface
– Low-power hardware touch sensor interface (TSI)
– General-purpose input/output
• Analog modules
– Two 16-bit SAR ADCs
– Programmable gain amplifier (PGA) (up to x64)
integrated into each ADC
– Two 12-bit DACs
– Three analog comparators (CMP) containing a 6-bit
DAC and programmable reference input
– Voltage reference
• Timers
– Programmable delay block
– Eight-channel motor control/general purpose/PWM
timer
– Two 2-channel quadrature decoder/general purpose
timers
– Periodic interrupt timers
– 16-bit low-power timer
– Carrier modulator transmitter
– Real-time clock
• Communication interfaces
– Two Controller Area Network (CAN) modules
– Three SPI modules
– Two I2C modules
– Six UART modules
– Secure Digital host controller (SDHC)
– I2S module
Freescale reserves the right to change the detail specifications as may be
required to permit improvements in the design of its products.
© 2011–2013 Freescale Semiconductor, Inc.
Table of Contents
1 Ordering parts...........................................................................3
5.4.2
Thermal attributes.................................................21
1.1 Determining valid orderable parts......................................3
6 Peripheral operating requirements and behaviors....................22
2 Part identification......................................................................3
6.1 Core modules....................................................................22
2.1 Description.........................................................................3
6.1.1
Debug trace timing specifications.........................22
2.2 Format...............................................................................3
6.1.2
JTAG electricals....................................................23
2.3 Fields.................................................................................3
6.2 System modules................................................................26
2.4 Example............................................................................4
6.3 Clock modules...................................................................26
3 Terminology and guidelines......................................................4
6.3.1
MCG specifications...............................................26
3.1 Definition: Operating requirement......................................4
6.3.2
Oscillator electrical specifications.........................28
3.2 Definition: Operating behavior...........................................5
6.3.3
32 kHz Oscillator Electrical Characteristics...........30
3.3 Definition: Attribute............................................................5
6.4 Memories and memory interfaces.....................................31
3.4 Definition: Rating...............................................................6
6.4.1
Flash electrical specifications................................31
3.5 Result of exceeding a rating..............................................6
6.4.2
EzPort Switching Specifications............................33
3.6 Relationship between ratings and operating
6.4.3
Flexbus Switching Specifications..........................34
requirements......................................................................6
6.5 Security and integrity modules..........................................37
3.7 Guidelines for ratings and operating requirements............7
6.6 Analog...............................................................................37
3.8 Definition: Typical value.....................................................7
6.6.1
ADC electrical specifications.................................37
3.9 Typical value conditions....................................................8
6.6.2
CMP and 6-bit DAC electrical specifications.........45
4 Ratings......................................................................................9
6.6.3
12-bit DAC electrical characteristics.....................47
4.1 Thermal handling ratings...................................................9
6.6.4
Voltage reference electrical specifications............50
4.2 Moisture handling ratings..................................................9
6.7 Timers................................................................................51
4.3 ESD handling ratings.........................................................9
6.8 Communication interfaces.................................................51
4.4 Voltage and current operating ratings...............................9
6.8.1
CAN switching specifications................................51
5 General.....................................................................................10
6.8.2
DSPI switching specifications (limited voltage
5.1 AC electrical characteristics..............................................10
5.2 Nonswitching electrical specifications...............................10
range)....................................................................52
6.8.3
DSPI switching specifications (full voltage range).53
5.2.1
Voltage and current operating requirements.........10
6.8.4
Inter-Integrated Circuit Interface (I2C) timing........55
5.2.2
LVD and POR operating requirements.................11
6.8.5
UART switching specifications..............................56
5.2.3
Voltage and current operating behaviors..............12
6.8.6
SDHC specifications.............................................56
5.2.4
Power mode transition operating behaviors..........14
6.8.7
I2S switching specifications..................................57
5.2.5
Power consumption operating behaviors..............15
5.2.6
EMC radiated emissions operating behaviors.......18
5.2.7
Designing with radiated emissions in mind...........19
7 Dimensions...............................................................................61
5.2.8
Capacitance attributes..........................................19
7.1 Obtaining package dimensions.........................................61
5.3 Switching specifications.....................................................19
8 Pinout........................................................................................61
6.9 Human-machine interfaces (HMI)......................................60
6.9.1
TSI electrical specifications...................................60
5.3.1
Device clock specifications...................................19
8.1 K10 Signal Multiplexing and Pin Assignments..................61
5.3.2
General switching specifications...........................19
8.2 K10 Pinouts.......................................................................67
5.4 Thermal specifications.......................................................20
9 Revision History........................................................................69
5.4.1
Thermal operating requirements...........................20
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
2
Freescale Semiconductor, Inc.
Ordering parts
1 Ordering parts
1.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web. To determine the orderable part
numbers for this device, go to freescale.com and perform a part number search for the
following device numbers: PK10 and MK10 .
2 Part identification
2.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
2.2 Format
Part numbers for this device have the following format:
Q K## A M FFF R T PP CC N
2.3 Fields
This table lists the possible values for each field in the part number (not all combinations
are valid):
Field
Description
Values
Q
Qualification status
• M = Fully qualified, general market flow
• P = Prequalification
K##
Kinetis family
• K10
A
Key attribute
• D = Cortex-M4 w/ DSP
• F = Cortex-M4 w/ DSP and FPU
M
Flash memory type
• N = Program flash only
• X = Program flash and FlexMemory
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
3
Terminology and guidelines
Field
Description
Values
FFF
Program flash memory size
•
•
•
•
•
•
•
32 = 32 KB
64 = 64 KB
128 = 128 KB
256 = 256 KB
512 = 512 KB
1M0 = 1 MB
2M0 = 2 MB
R
Silicon revision
• Z = Initial
• (Blank) = Main
• A = Revision after main
T
Temperature range (°C)
• V = –40 to 105
• C = –40 to 85
PP
Package identifier
•
•
•
•
•
•
•
•
•
•
•
FM = 32 QFN (5 mm x 5 mm)
FT = 48 QFN (7 mm x 7 mm)
LF = 48 LQFP (7 mm x 7 mm)
LH = 64 LQFP (10 mm x 10 mm)
MP = 64 MAPBGA (5 mm x 5 mm)
LK = 80 LQFP (12 mm x 12 mm)
LL = 100 LQFP (14 mm x 14 mm)
MC = 121 MAPBGA (8 mm x 8 mm)
LQ = 144 LQFP (20 mm x 20 mm)
MD = 144 MAPBGA (13 mm x 13 mm)
MJ = 256 MAPBGA (17 mm x 17 mm)
CC
Maximum CPU frequency (MHz)
•
•
•
•
•
5 = 50 MHz
7 = 72 MHz
10 = 100 MHz
12 = 120 MHz
15 = 150 MHz
N
Packaging type
• R = Tape and reel
• (Blank) = Trays
2.4 Example
This is an example part number:
MK10DN512ZVMD10
3 Terminology and guidelines
3.1 Definition: Operating requirement
An operating requirement is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation and
possibly decreasing the useful life of the chip.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
4
Freescale Semiconductor, Inc.
Terminology and guidelines
3.1.1 Example
This is an example of an operating requirement:
Symbol
VDD
Description
1.0 V core supply
voltage
Min.
0.9
Max.
1.1
Unit
V
3.2 Definition: Operating behavior
An operating behavior is a specified value or range of values for a technical
characteristic that are guaranteed during operation if you meet the operating requirements
and any other specified conditions.
3.2.1 Example
This is an example of an operating behavior:
Symbol
IWP
Description
Min.
Digital I/O weak pullup/ 10
pulldown current
Max.
130
Unit
µA
3.3 Definition: Attribute
An attribute is a specified value or range of values for a technical characteristic that are
guaranteed, regardless of whether you meet the operating requirements.
3.3.1 Example
This is an example of an attribute:
Symbol
CIN_D
Description
Input capacitance:
digital pins
Min.
—
Max.
7
Unit
pF
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
5
Terminology and guidelines
3.4 Definition: Rating
A rating is a minimum or maximum value of a technical characteristic that, if exceeded,
may cause permanent chip failure:
• Operating ratings apply during operation of the chip.
• Handling ratings apply when the chip is not powered.
3.4.1 Example
This is an example of an operating rating:
Symbol
VDD
Description
1.0 V core supply
voltage
Min.
–0.3
Max.
Unit
1.2
V
3.5 Result of exceeding a rating
Failures in time (ppm)
40
30
The likelihood of permanent chip failure increases rapidly as
soon as a characteristic begins to exceed one of its operating ratings.
20
10
0
Operating rating
Measured characteristic
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
6
Freescale Semiconductor, Inc.
Terminology and guidelines
3.6 Relationship between ratings and operating requirements
e
Op
ing
rat
r
(
ng
ati
in.
t (m
)
n.
mi
rat
e
Op
ing
)
t (m
e
ir
qu
re
n
me
ing
rat
e
Op
ax
.)
e
ir
qu
re
n
me
ing
rat
e
Op
ng
ati
ax
(m
.)
r
Fatal range
Degraded operating range
Normal operating range
Degraded operating range
Fatal range
Expected permanent failure
- No permanent failure
- Possible decreased life
- Possible incorrect operation
- No permanent failure
- Correct operation
- No permanent failure
- Possible decreased life
- Possible incorrect operation
Expected permanent failure
–∞
∞
Operating (power on)
g
lin
nd
Ha
in
rat
n.)
mi
g(
nd
Ha
g
lin
ing
rat
ax
(m
.)
Fatal range
Handling range
Fatal range
Expected permanent failure
No permanent failure
Expected permanent failure
–∞
Handling (power off)
∞
3.7 Guidelines for ratings and operating requirements
Follow these guidelines for ratings and operating requirements:
• Never exceed any of the chip’s ratings.
• During normal operation, don’t exceed any of the chip’s operating requirements.
• If you must exceed an operating requirement at times other than during normal
operation (for example, during power sequencing), limit the duration as much as
possible.
3.8 Definition: Typical value
A typical value is a specified value for a technical characteristic that:
• Lies within the range of values specified by the operating behavior
• Given the typical manufacturing process, is representative of that characteristic
during operation when you meet the typical-value conditions or other specified
conditions
Typical values are provided as design guidelines and are neither tested nor guaranteed.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
7
Terminology and guidelines
3.8.1 Example 1
This is an example of an operating behavior that includes a typical value:
Symbol
Description
IWP
Digital I/O weak
pullup/pulldown
current
Min.
10
Typ.
70
Max.
130
Unit
µA
3.8.2 Example 2
This is an example of a chart that shows typical values for various voltage and
temperature conditions:
5000
4500
4000
TJ
IDD_STOP (μA)
3500
150 °C
3000
105 °C
2500
25 °C
2000
–40 °C
1500
1000
500
0
0.90
0.95
1.00
1.05
1.10
VDD (V)
3.9 Typical value conditions
Typical values assume you meet the following conditions (or other conditions as
specified):
Symbol
Description
Value
Unit
TA
Ambient temperature
25
°C
VDD
3.3 V supply voltage
3.3
V
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
8
Freescale Semiconductor, Inc.
Ratings
4 Ratings
4.1 Thermal handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
TSTG
Storage temperature
–55
150
°C
1
TSDR
Solder temperature, lead-free
—
260
°C
2
Solder temperature, leaded
—
245
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
4.2 Moisture handling ratings
Symbol
MSL
Description
Moisture sensitivity level
Min.
Max.
Unit
Notes
—
3
—
1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
4.3 ESD handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
VHBM
Electrostatic discharge voltage, human body model
-2000
+2000
V
1
VCDM
Electrostatic discharge voltage, charged-device model
-500
+500
V
2
Latch-up current at ambient temperature of 105°C
-100
+100
mA
3
ILAT
1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human Body
Model (HBM).
2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for
Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components.
3. Determined according to JEDEC Standard JESD78, IC Latch-Up Test.
4.4 Voltage and current operating ratings
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
9
General
Symbol
Description
Min.
Max.
Unit
VDD
Digital supply voltage
–0.3
3.8
V
IDD
Digital supply current
—
185
mA
VDIO
Digital input voltage (except RESET, EXTAL, and XTAL)
–0.3
5.5
V
VAIO
Analog1,
RESET, EXTAL, and XTAL input voltage
–0.3
VDD + 0.3
V
Maximum current single pin limit (applies to all digital pins)
–25
25
mA
VDD – 0.3
VDD + 0.3
V
–0.3
3.8
V
ID
VDDA
Analog supply voltage
VBAT
RTC battery supply voltage
1. Analog pins are defined as pins that do not have an associated general purpose I/O port function.
5 General
5.1 AC electrical characteristics
Unless otherwise specified, propagation delays are measured from the 50% to the 50%
point, and rise and fall times are measured at the 20% and 80% points, as shown in the
following figure.
Figure 1. Input signal measurement reference
All digital I/O switching characteristics assume:
1. output pins
• have CL=30pF loads,
• are configured for fast slew rate (PORTx_PCRn[SRE]=0), and
• are configured for high drive strength (PORTx_PCRn[DSE]=1)
2. input pins
• have their passive filter disabled (PORTx_PCRn[PFE]=0)
5.2 Nonswitching electrical specifications
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
10
Freescale Semiconductor, Inc.
General
5.2.1 Voltage and current operating requirements
Table 1. Voltage and current operating requirements
Symbol
Description
Min.
Max.
Unit
VDD
Supply voltage
1.71
3.6
V
VDDA
Analog supply voltage
1.71
3.6
V
VDD – VDDA VDD-to-VDDA differential voltage
–0.1
0.1
V
VSS – VSSA VSS-to-VSSA differential voltage
–0.1
0.1
V
1.71
3.6
V
• 2.7 V ≤ VDD ≤ 3.6 V
0.7 × VDD
—
V
• 1.7 V ≤ VDD ≤ 2.7 V
0.75 × VDD
—
V
• 2.7 V ≤ VDD ≤ 3.6 V
—
0.35 × VDD
V
• 1.7 V ≤ VDD ≤ 2.7 V
—
0.3 × VDD
V
0.06 × VDD
—
V
-5
—
mA
VBAT
VIH
VIL
RTC battery supply voltage
Input high voltage
Input low voltage
VHYS
Input hysteresis
IICDIO
Digital pin negative DC injection current — single pin
• VIN < VSS-0.3V
IICAIO
IICcont
1
Analog2, EXTAL, and XTAL pin DC injection current —
single pin
3
mA
• VIN < VSS-0.3V (Negative current injection)
-5
—
• VIN > VDD+0.3V (Positive current injection)
—
+5
-25
—
—
+25
Contiguous pin DC injection current —regional limit,
includes sum of negative injection currents or sum of
positive injection currents of 16 contiguous pins
• Negative current injection
• Positive current injection
mA
VODPU
Open drain pullup voltage level
VDD
VDD
V
VRAM
VDD voltage required to retain RAM
1.2
—
V
VPOR_VBAT
—
V
VRFVBAT
Notes
VBAT voltage required to retain the VBAT register file
4
1. All 5 V tolerant digital I/O pins are internally clamped to VSS through an ESD protection diode. There is no diode
connection to VDD. If VIN is less than VDIO_MIN, a current limiting resistor is required. The negative DC injection current
limiting resistor is calculated as R=(VDIO_MIN-VIN)/|IICDIO|.
2. Analog pins are defined as pins that do not have an associated general purpose I/O port function. Additionally, EXTAL and
XTAL are analog pins.
3. All analog pins are internally clamped to VSS and VDD through ESD protection diodes. If VIN is less than VAIO_MIN or greater
than VAIO_MAX, a current limiting resistor is required. The negative DC injection current limiting resistor is calculated as
R=(VAIO_MIN-VIN)/|IICAIO|. The positive injection current limiting resistor is calculated as R=(VIN-VAIO_MAX)/|IICAIO|. Select the
larger of these two calculated resistances if the pin is exposed to positive and negative injection currents.
4. Open drain outputs must be pulled to VDD.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
11
General
5.2.2 LVD and POR operating requirements
Table 2. VDD supply LVD and POR operating requirements
Symbol
Description
Min.
Typ.
Max.
Unit
VPOR
Falling VDD POR detect voltage
0.8
1.1
1.5
V
VLVDH
Falling low-voltage detect threshold — high
range (LVDV=01)
2.48
2.56
2.64
V
Low-voltage warning thresholds — high range
1
VLVW1H
• Level 1 falling (LVWV=00)
2.62
2.70
2.78
V
VLVW2H
• Level 2 falling (LVWV=01)
2.72
2.80
2.88
V
VLVW3H
• Level 3 falling (LVWV=10)
2.82
2.90
2.98
V
VLVW4H
• Level 4 falling (LVWV=11)
2.92
3.00
3.08
V
—
±80
—
mV
1.54
1.60
1.66
V
VHYSH
Low-voltage inhibit reset/recover hysteresis —
high range
VLVDL
Falling low-voltage detect threshold — low range
(LVDV=00)
Low-voltage warning thresholds — low range
1
VLVW1L
• Level 1 falling (LVWV=00)
1.74
1.80
1.86
V
VLVW2L
• Level 2 falling (LVWV=01)
1.84
1.90
1.96
V
VLVW3L
• Level 3 falling (LVWV=10)
1.94
2.00
2.06
V
VLVW4L
• Level 4 falling (LVWV=11)
2.04
2.10
2.16
V
—
±60
—
mV
VHYSL
Low-voltage inhibit reset/recover hysteresis —
low range
Notes
VBG
Bandgap voltage reference
0.97
1.00
1.03
V
tLPO
Internal low power oscillator period — factory
trimmed
900
1000
1100
μs
1. Rising thresholds are falling threshold + hysteresis voltage
Table 3. VBAT power operating requirements
Symbol
Description
VPOR_VBAT Falling VBAT supply POR detect voltage
Min.
Typ.
Max.
Unit
0.8
1.1
1.5
V
Notes
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
12
Freescale Semiconductor, Inc.
General
5.2.3 Voltage and current operating behaviors
Table 4. Voltage and current operating behaviors
Symbol
VOH
Min.
Typ.1
Max.
Unit
• 2.7 V ≤ VDD ≤ 3.6 V, IOH = -9mA
VDD – 0.5
—
—
V
• 1.71 V ≤ VDD ≤ 2.7 V, IOH = -3mA
VDD – 0.5
—
—
V
• 2.7 V ≤ VDD ≤ 3.6 V, IOH = -2mA
VDD – 0.5
—
—
V
• 1.71 V ≤ VDD ≤ 2.7 V, IOH = -0.6mA
VDD – 0.5
—
—
V
—
—
100
mA
Description
Notes
Output high voltage — high drive strength
Output high voltage — low drive strength
IOHT
Output high current total for all ports
VOL
Output low voltage — high drive strength
2
• 2.7 V ≤ VDD ≤ 3.6 V, IOL = 9mA
—
—
0.5
V
• 1.71 V ≤ VDD ≤ 2.7 V, IOL = 3mA
—
—
0.5
V
• 2.7 V ≤ VDD ≤ 3.6 V, IOL = 2mA
—
—
0.5
V
• 1.71 V ≤ VDD ≤ 2.7 V, IOL = 0.6mA
—
—
0.5
V
—
—
100
mA
Output low voltage — low drive strength
IOLT
Output low current total for all ports
IINA
Input leakage current, analog pins and digital
pins configured as analog inputs
3, 4
• VSS ≤ VIN ≤ VDD
• All pins except EXTAL32, XTAL32,
EXTAL, XTAL
• EXTAL (PTA18) and XTAL (PTA19)
• EXTAL32, XTAL32
IIND
—
0.002
0.5
μA
—
0.004
1.5
μA
—
0.075
10
μA
Input leakage current, digital pins
4, 5
• VSS ≤ VIN ≤ VIL
• All digital pins
—
0.002
0.5
μA
—
0.002
0.5
μA
—
0.004
1
μA
• VIN = VDD
• All digital pins except PTD7
• PTD7
IIND
Input leakage current, digital pins
4, 5, 6
• VIL < VIN < VDD
• VDD = 3.6 V
—
18
26
μA
• VDD = 3.0 V
—
12
49
μA
• VDD = 2.5 V
—
8
13
μA
• VDD = 1.7 V
—
3
6
μA
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
13
General
Table 4. Voltage and current operating behaviors (continued)
Symbol
IIND
Description
Min.
Max.
Unit
Input leakage current, digital pins
• VDD < VIN < 5.5 V
ZIND
Typ.1
Notes
4, 5
—
1
50
μA
Input impedance examples, digital pins
4, 7
• VDD = 3.6 V
—
—
48
kΩ
• VDD = 3.0 V
—
—
55
kΩ
• VDD = 2.5 V
—
—
57
kΩ
• VDD = 1.7 V
—
—
85
kΩ
RPU
Internal pullup resistors
20
35
50
kΩ
8
RPD
Internal pulldown resistors
20
35
50
kΩ
9
1.
2.
3.
4.
5.
6.
7.
Typical values characterized at 25°C and VDD = 3.6 V unless otherwise noted.
Open drain outputs must be pulled to VDD.
Analog pins are defined as pins that do not have an associated general purpose I/O port function.
Digital pins have an associated GPIO port function and have 5V tolerant inputs, except EXTAL and XTAL.
Internal pull-up/pull-down resistors disabled.
Characterized, not tested in production.
Examples calculated using VIL relation, VDD, and max IIND: ZIND=VIL/IIND. This is the impedance needed to pull a high
signal to a level below VIL due to leakage when VIL < VIN < VDD. These examples assume signal source low = 0 V.
8. Measured at VDD supply voltage = VDD min and Vinput = VSS
9. Measured at VDD supply voltage = VDD min and Vinput = VDD
I IND
Digital input
Source
+
–
Z IND
5.2.4 Power mode transition operating behaviors
All specifications except tPOR, and VLLSx→RUN recovery times in the following table
assume this clock configuration:
•
•
•
•
•
CPU and system clocks = 100 MHz
Bus clock = 50 MHz
FlexBus clock = 50 MHz
Flash clock = 25 MHz
MCG mode: FEI
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
14
Freescale Semiconductor, Inc.
General
Table 5. Power mode transition operating behaviors
Symbol
tPOR
Description
Min.
Max.
After a POR event, amount of time from the point VDD
reaches 1.71 V to execution of the first instruction
across the operating temperature range of the chip.
• VDD slew rate ≥ 5.7 kV/s
• VDD slew rate < 5.7 kV/s
• VLLS1 → RUN
• VLLS2 → RUN
• VLLS3 → RUN
• LLS → RUN
• VLPS → RUN
• STOP → RUN
Unit
Notes
μs
1
—
300
—
1.7 V / (VDD
slew rate)
—
134
μs
—
96
μs
—
96
μs
—
6.2
μs
—
5.9
μs
—
5.9
μs
1. Normal boot (FTFL_OPT[LPBOOT]=1)
5.2.5 Power consumption operating behaviors
Table 6. Power consumption operating behaviors
Symbol
IDDA
IDD_RUN
Description
Analog supply current
Typ.
Max.
Unit
Notes
—
—
See note
mA
1
Run mode current — all peripheral clocks
disabled, code executing from flash
• @ 1.8V
• @ 3.0V
IDD_RUN
Min.
2
—
45
70
mA
—
47
72
mA
Run mode current — all peripheral clocks
enabled, code executing from flash
• @ 1.8V
3, 4
—
61
85
mA
—
63
71
mA
—
72
87
mA
• @ 3.0V
• @ 25°C
• @ 125°C
IDD_WAIT
Wait mode high frequency current at 3.0 V — all
peripheral clocks disabled
—
35
—
mA
2
IDD_WAIT
Wait mode reduced frequency current at 3.0 V —
all peripheral clocks disabled
—
15
—
mA
5
IDD_VLPR
Very-low-power run mode current at 3.0 V — all
peripheral clocks disabled
—
N/A
—
mA
6
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
15
General
Table 6. Power consumption operating behaviors (continued)
Symbol
Description
Min.
Typ.
Max.
Unit
Notes
IDD_VLPR
Very-low-power run mode current at 3.0 V — all
peripheral clocks enabled
—
N/A
—
mA
7
IDD_VLPW
Very-low-power wait mode current at 3.0 V — all
peripheral clocks disabled
—
N/A
—
mA
8
IDD_STOP
Stop mode current at 3.0 V
• @ –40 to 25°C
—
0.59
1.4
mA
• @ 70°C
—
2.26
7.9
mA
• @ 105°C
—
5.94
19.2
mA
• @ –40 to 25°C
—
93
435
μA
• @ 70°C
—
520
2000
μA
• @ 105°C
—
1350
4000
μA
IDD_VLPS
IDD_LLS
IDD_VLLS3
IDD_VLLS2
IDD_VLLS1
IDD_VBAT
Very-low-power stop mode current at 3.0 V
Low leakage stop mode current at 3.0 V
9
• @ –40 to 25°C
—
4.8
20
μA
• @ 70°C
—
28
68
μA
• @ 105°C
—
126
270
μA
Very low-leakage stop mode 3 current at 3.0 V
9
• @ –40 to 25°C
—
3.1
8.9
μA
• @ 70°C
—
17
35
μA
• @ 105°C
—
82
148
μA
• @ –40 to 25°C
—
2.2
5.4
μA
• @ 70°C
—
7.1
12.5
μA
• @ 105°C
—
41
125
μA
• @ –40 to 25°C
—
2.1
7.6
μA
• @ 70°C
—
6.2
13.5
μA
• @ 105°C
—
30
46
μA
—
0.33
0.39
μA
—
0.60
0.78
μA
—
1.97
2.9
μA
Very low-leakage stop mode 2 current at 3.0 V
Very low-leakage stop mode 1 current at 3.0 V
Average current with RTC and 32kHz disabled at
3.0 V
• @ –40 to 25°C
• @ 70°C
• @ 105°C
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
16
Freescale Semiconductor, Inc.
General
Table 6. Power consumption operating behaviors (continued)
Symbol
Description
Min.
IDD_VBAT
Average current when CPU is not accessing RTC
registers
Typ.
Max.
Unit
Notes
10
• @ 1.8V
• @ –40 to 25°C
• @ 70°C
• @ 105°C
—
0.71
0.81
μA
—
1.01
1.3
μA
—
2.82
4.3
μA
—
0.84
0.94
μA
—
1.17
1.5
μA
—
3.16
4.6
μA
• @ 3.0V
• @ –40 to 25°C
• @ 70°C
• @ 105°C
1. The analog supply current is the sum of the active or disabled current for each of the analog modules on the device. See
each module's specification for its supply current.
2. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock . MCG configured for FEI mode.
All peripheral clocks disabled.
3. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock. MCG configured for FEI mode. All
peripheral clocks enabled.
4. Max values are measured with CPU executing DSP instructions.
5. 25MHz core and system clock, 25MHz bus clock, and 12.5MHz FlexBus and flash clock. MCG configured for FEI mode.
6. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks
disabled. Code executing from flash.
7. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks
enabled but peripherals are not in active operation. Code executing from flash.
8. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks
disabled.
9. Data reflects devices with 128 KB of RAM. For devices with 64 KB of RAM, power consumption is reduced by 2 μA. For
devices with 32 KB of RAM, power consumption is reduced by 3 μA.
10. Includes 32kHz oscillator current and RTC operation.
5.2.5.1
Diagram: Typical IDD_RUN operating behavior
The following data was measured under these conditions:
• MCG in FBE mode for 50 MHz and lower frequencies. MCG in FEE mode at greater
than 50 MHz frequencies.
• No GPIOs toggled
• Code execution from flash with cache enabled
• For the ALLOFF curve, all peripheral clocks are disabled except FTFL
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
17
General
Figure 2. Run mode supply current vs. core frequency
5.2.6 EMC radiated emissions operating behaviors
Table 7. EMC radiated emissions operating behaviors as measured on 144LQFP and
144MAPBGA packages
Symbol
Description
Frequency
band (MHz)
144LQFP
144MAPBGA
Unit
Notes
1,2
VRE1
Radiated emissions voltage, band 1
0.15–50
23
12
dBμV
VRE2
Radiated emissions voltage, band 2
50–150
27
24
dBμV
VRE3
Radiated emissions voltage, band 3
150–500
28
27
dBμV
VRE4
Radiated emissions voltage, band 4
500–1000
14
11
dBμV
IEC level
0.15–1000
K
K
—
VRE_IEC
2, 3
1. Determined according to IEC Standard 61967-1, Integrated Circuits - Measurement of Electromagnetic Emissions, 150
kHz to 1 GHz Part 1: General Conditions and Definitions and IEC Standard 61967-2, Integrated Circuits - Measurement of
Electromagnetic Emissions, 150 kHz to 1 GHz Part 2: Measurement of Radiated Emissions—TEM Cell and Wideband
TEM Cell Method. Measurements were made while the microcontroller was running basic application code. The reported
emission level is the value of the maximum measured emission, rounded up to the next whole number, from among the
measured orientations in each frequency range.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
18
Freescale Semiconductor, Inc.
General
2. VDD = 3.3 V, TA = 25 °C, fOSC = 12 MHz (crystal), fSYS = 96 MHz, fBUS = 48MHz
3. Specified according to Annex D of IEC Standard 61967-2, Measurement of Radiated Emissions—TEM Cell and Wideband
TEM Cell Method
5.2.7 Designing with radiated emissions in mind
To find application notes that provide guidance on designing your system to minimize
interference from radiated emissions:
1. Go to www.freescale.com.
2. Perform a keyword search for “EMC design.”
5.2.8 Capacitance attributes
Table 8. Capacitance attributes
Symbol
Description
Min.
Max.
Unit
CIN_A
Input capacitance: analog pins
—
7
pF
CIN_D
Input capacitance: digital pins
—
7
pF
5.3 Switching specifications
5.3.1 Device clock specifications
Table 9. Device clock specifications
Symbol
Description
Min.
Max.
Unit
Notes
Normal run mode
fSYS
System and core clock
—
100
MHz
fBUS
Bus clock
—
50
MHz
FlexBus clock
—
50
MHz
fFLASH
Flash clock
—
25
MHz
fLPTMR
LPTMR clock
—
25
MHz
FB_CLK
5.3.2 General switching specifications
These general purpose specifications apply to all signals configured for GPIO, UART,
CAN, CMT, and I2C signals.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
19
General
Table 10. General switching specifications
Symbol
Description
Min.
Max.
Unit
Notes
GPIO pin interrupt pulse width (digital glitch filter
disabled) — Synchronous path
1.5
—
Bus clock
cycles
1, 2
GPIO pin interrupt pulse width (digital glitch filter
disabled, analog filter enabled) — Asynchronous path
100
—
ns
3
GPIO pin interrupt pulse width (digital glitch filter
disabled, analog filter disabled) — Asynchronous path
16
—
ns
3
External reset pulse width (digital glitch filter disabled)
100
—
ns
3
2
—
Bus clock
cycles
Mode select (EZP_CS) hold time after reset
deassertion
Port rise and fall time (high drive strength)
4
• Slew disabled
• 1.71 ≤ VDD ≤ 2.7V
—
12
ns
• 2.7 ≤ VDD ≤ 3.6V
—
6
ns
• 1.71 ≤ VDD ≤ 2.7V
—
36
ns
• 2.7 ≤ VDD ≤ 3.6V
—
24
ns
• Slew enabled
Port rise and fall time (low drive strength)
5
• Slew disabled
• 1.71 ≤ VDD ≤ 2.7V
—
12
ns
• 2.7 ≤ VDD ≤ 3.6V
—
6
ns
• 1.71 ≤ VDD ≤ 2.7V
—
36
ns
• 2.7 ≤ VDD ≤ 3.6V
—
24
ns
• Slew enabled
1. This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or
may not be recognized. In Stop, VLPS, LLS, and VLLSx modes, the synchronizer is bypassed so shorter pulses can be
recognized in that case.
2. The greater synchronous and asynchronous timing must be met.
3. This is the minimum pulse width that is guaranteed to be recognized as a pin interrupt request in Stop, VLPS, LLS, and
VLLSx modes.
4. 75 pF load
5. 15 pF load
5.4 Thermal specifications
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
20
Freescale Semiconductor, Inc.
General
5.4.1 Thermal operating requirements
Table 11. Thermal operating requirements
Symbol
Description
Min.
Max.
Unit
TJ
Die junction temperature
–40
125
°C
TA
Ambient temperature
–40
105
°C
5.4.2 Thermal attributes
Board type
Symbol
Description
Unit
Notes
Single-layer
(1s)
RθJA
Thermal
45
resistance,
junction to
ambient (natural
convection)
48
°C/W
1
Four-layer
(2s2p)
RθJA
Thermal
36
resistance,
junction to
ambient (natural
convection)
29
°C/W
1
Single-layer
(1s)
RθJMA
Thermal
36
resistance,
junction to
ambient (200 ft./
min. air speed)
38
°C/W
1
Four-layer
(2s2p)
RθJMA
Thermal
30
resistance,
junction to
ambient (200 ft./
min. air speed)
25
°C/W
1
—
RθJB
Thermal
resistance,
junction to
board
24
16
°C/W
2
—
RθJC
Thermal
resistance,
junction to case
9
9
°C/W
3
—
ΨJT
Thermal
2
characterization
parameter,
junction to
package top
outside center
(natural
convection)
2
°C/W
4
1.
144 LQFP
144
MAPBGA
Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air), or EIA/JEDEC Standard JESD51-6, Integrated Circuit Thermal Test Method
Environmental Conditions—Forced Convection (Moving Air).
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
21
Peripheral operating requirements and behaviors
2.
3.
4.
Determined according to JEDEC Standard JESD51-8, Integrated Circuit Thermal Test Method Environmental
Conditions—Junction-to-Board.
Determined according to Method 1012.1 of MIL-STD 883, Test Method Standard, Microcircuits, with the cold plate
temperature used for the case temperature. The value includes the thermal resistance of the interface material
between the top of the package and the cold plate.
Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air).
6 Peripheral operating requirements and behaviors
6.1 Core modules
6.1.1 Debug trace timing specifications
Table 12. Debug trace operating behaviors
Symbol
Description
Min.
Max.
Unit
Tcyc
Clock period
Frequency dependent
MHz
Twl
Low pulse width
2
—
ns
Twh
High pulse width
2
—
ns
Tr
Clock and data rise time
—
3
ns
Tf
Clock and data fall time
—
3
ns
Ts
Data setup
3
—
ns
Th
Data hold
2
—
ns
Figure 3. TRACE_CLKOUT specifications
TRACE_CLKOUT
Ts
Th
Ts
Th
TRACE_D[3:0]
Figure 4. Trace data specifications
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
22
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
6.1.2 JTAG electricals
Table 13. JTAG limited voltage range electricals
Symbol
J1
Description
Min.
Max.
Unit
Operating voltage
2.7
3.6
V
TCLK frequency of operation
MHz
• Boundary Scan
0
10
• JTAG and CJTAG
0
25
• Serial Wire Debug
0
50
1/J1
—
ns
• Boundary Scan
50
—
ns
• JTAG and CJTAG
20
—
ns
• Serial Wire Debug
10
—
ns
J4
TCLK rise and fall times
—
3
ns
J5
Boundary scan input data setup time to TCLK rise
20
—
ns
J6
Boundary scan input data hold time after TCLK rise
0
—
ns
J7
TCLK low to boundary scan output data valid
—
25
ns
J8
TCLK low to boundary scan output high-Z
—
25
ns
J9
TMS, TDI input data setup time to TCLK rise
8
—
ns
J10
TMS, TDI input data hold time after TCLK rise
1
—
ns
J11
TCLK low to TDO data valid
—
17
ns
J12
TCLK low to TDO high-Z
—
17
ns
J13
TRST assert time
100
—
ns
J14
TRST setup time (negation) to TCLK high
8
—
ns
J2
TCLK cycle period
J3
TCLK clock pulse width
Table 14. JTAG full voltage range electricals
Symbol
J1
J2
Description
Min.
Max.
Unit
Operating voltage
1.71
3.6
V
TCLK frequency of operation
MHz
• Boundary Scan
0
10
• JTAG and CJTAG
0
20
• Serial Wire Debug
0
40
1/J1
—
TCLK cycle period
ns
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
23
Peripheral operating requirements and behaviors
Table 14. JTAG full voltage range electricals (continued)
Symbol
J3
Description
Min.
Max.
Unit
• Boundary Scan
50
—
ns
• JTAG and CJTAG
25
—
ns
• Serial Wire Debug
12.5
—
ns
TCLK clock pulse width
J4
TCLK rise and fall times
—
3
ns
J5
Boundary scan input data setup time to TCLK rise
20
—
ns
J6
Boundary scan input data hold time after TCLK rise
0
—
ns
J7
TCLK low to boundary scan output data valid
—
25
ns
J8
TCLK low to boundary scan output high-Z
—
25
ns
J9
TMS, TDI input data setup time to TCLK rise
8
—
ns
J10
TMS, TDI input data hold time after TCLK rise
1.4
—
ns
J11
TCLK low to TDO data valid
—
22.1
ns
J12
TCLK low to TDO high-Z
—
22.1
ns
J13
TRST assert time
100
—
ns
J14
TRST setup time (negation) to TCLK high
8
—
ns
J2
J3
J3
TCLK (input)
J4
J4
Figure 5. Test clock input timing
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
24
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
TCLK
J5
Data inputs
J6
Input data valid
J7
Data outputs
Output data valid
J8
Data outputs
J7
Data outputs
Output data valid
Figure 6. Boundary scan (JTAG) timing
TCLK
J9
TDI/TMS
J10
Input data valid
J11
TDO
Output data valid
J12
TDO
J11
TDO
Output data valid
Figure 7. Test Access Port timing
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
25
Peripheral operating requirements and behaviors
TCLK
J14
J13
TRST
Figure 8. TRST timing
6.2 System modules
There are no specifications necessary for the device's system modules.
6.3 Clock modules
6.3.1 MCG specifications
Table 15. MCG specifications
Symbol
Description
Min.
Typ.
Max.
Unit
—
32.768
—
kHz
31.25
—
38.2
kHz
—
± 0.3
± 0.6
%fdco
1
Total deviation of trimmed average DCO output
frequency over fixed voltage and temperature
range of 0–70°C
—
± 1.5
± 4.5
%fdco
1
fintf_ft
Internal reference frequency (fast clock) —
factory trimmed at nominal VDD and 25°C
—
4
—
MHz
fintf_t
Internal reference frequency (fast clock) — user
trimmed at nominal VDD and 25 °C
3
—
5
MHz
fints_ft
Internal reference frequency (slow clock) —
factory trimmed at nominal VDD and 25 °C
fints_t
Internal reference frequency (slow clock) — user
trimmed — over fixed voltage and temperature
range of 0–70°C
Δfdco_res_t Resolution of trimmed average DCO output
frequency at fixed voltage and temperature —
using SCTRIM and SCFTRIM
Δfdco_t
floc_low
Loss of external clock minimum frequency —
RANGE = 00
(3/5) x
fints_t
—
—
kHz
floc_high
Loss of external clock minimum frequency —
RANGE = 01, 10, or 11
(16/5) x
fints_t
—
—
kHz
31.25
—
39.0625
kHz
Notes
FLL
ffll_ref
FLL reference frequency range
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
26
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 15. MCG specifications (continued)
Symbol
fdco
Description
DCO output
frequency range
Low range (DRS=00)
Min.
Typ.
Max.
Unit
Notes
20
20.97
25
MHz
2, 3
40
41.94
50
MHz
60
62.91
75
MHz
80
83.89
100
MHz
—
23.99
—
MHz
—
47.97
—
MHz
—
71.99
—
MHz
—
95.98
—
MHz
—
180
—
—
150
—
—
—
1
ms
48.0
—
100
MHz
—
1060
—
µA
—
600
—
µA
2.0
—
4.0
MHz
640 × ffll_ref
Mid range (DRS=01)
1280 × ffll_ref
Mid-high range (DRS=10)
1920 × ffll_ref
High range (DRS=11)
2560 × ffll_ref
fdco_t_DMX32 DCO output
frequency
Low range (DRS=00)
4, 5
732 × ffll_ref
Mid range (DRS=01)
1464 × ffll_ref
Mid-high range (DRS=10)
2197 × ffll_ref
High range (DRS=11)
2929 × ffll_ref
Jcyc_fll
FLL period jitter
• fVCO = 48 MHz
• fVCO = 98 MHz
tfll_acquire
FLL target frequency acquisition time
ps
6
PLL
fvco
VCO operating frequency
Ipll
PLL operating current
• PLL @ 96 MHz (fosc_hi_1 = 8 MHz, fpll_ref =
2 MHz, VDIV multiplier = 48)
Ipll
PLL operating current
• PLL @ 48 MHz (fosc_hi_1 = 8 MHz, fpll_ref =
2 MHz, VDIV multiplier = 24)
fpll_ref
PLL reference frequency range
Jcyc_pll
PLL period jitter (RMS)
Jacc_pll
• fvco = 48 MHz
—
120
—
ps
• fvco = 100 MHz
—
50
—
ps
PLL accumulated jitter over 1µs (RMS)
8
• fvco = 48 MHz
—
1350
—
ps
• fvco = 100 MHz
—
600
—
ps
Lock entry frequency tolerance
± 1.49
—
± 2.98
%
Dunl
Lock exit frequency tolerance
± 4.47
—
± 5.97
%
Lock detector detection time
7
8
Dlock
tpll_lock
7
—
—
10-6
150 ×
+ 1075(1/
fpll_ref)
s
9
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
27
Peripheral operating requirements and behaviors
1. This parameter is measured with the internal reference (slow clock) being used as a reference to the FLL (FEI clock
mode).
2. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=0.
3. The resulting system clock frequencies should not exceed their maximum specified values. The DCO frequency deviation
(Δfdco_t) over voltage and temperature should be considered.
4. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=1.
5. The resulting clock frequency must not exceed the maximum specified clock frequency of the device.
6. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed,
DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE,
FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running.
7. Excludes any oscillator currents that are also consuming power while PLL is in operation.
8. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise characteristics of
each PCB and results will vary.
9. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled
(BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes
it is already running.
6.3.2 Oscillator electrical specifications
This section provides the electrical characteristics of the module.
6.3.2.1
Oscillator DC electrical specifications
Table 16. Oscillator DC electrical specifications
Symbol
Description
Min.
Typ.
Max.
Unit
VDD
Supply voltage
1.71
—
3.6
V
IDDOSC
IDDOSC
Supply current — low-power mode (HGO=0)
Notes
1
• 32 kHz
—
500
—
nA
• 4 MHz
—
200
—
μA
• 8 MHz (RANGE=01)
—
300
—
μA
• 16 MHz
—
950
—
μA
• 24 MHz
—
1.2
—
mA
• 32 MHz
—
1.5
—
mA
Supply current — high gain mode (HGO=1)
1
• 32 kHz
—
25
—
μA
• 4 MHz
—
400
—
μA
• 8 MHz (RANGE=01)
—
500
—
μA
• 16 MHz
—
2.5
—
mA
• 24 MHz
—
3
—
mA
• 32 MHz
—
4
—
mA
Cx
EXTAL load capacitance
—
—
—
2, 3
Cy
XTAL load capacitance
—
—
—
2, 3
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
28
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 16. Oscillator DC electrical specifications (continued)
Symbol
RF
RS
Description
Min.
Typ.
Max.
Unit
Notes
Feedback resistor — low-frequency, low-power
mode (HGO=0)
—
—
—
MΩ
2, 4
Feedback resistor — low-frequency, high-gain
mode (HGO=1)
—
10
—
MΩ
Feedback resistor — high-frequency, low-power
mode (HGO=0)
—
—
—
MΩ
Feedback resistor — high-frequency, high-gain
mode (HGO=1)
—
1
—
MΩ
Series resistor — low-frequency, low-power
mode (HGO=0)
—
—
—
kΩ
Series resistor — low-frequency, high-gain mode
(HGO=1)
—
200
—
kΩ
Series resistor — high-frequency, low-power
mode (HGO=0)
—
—
—
kΩ
—
0
—
kΩ
Peak-to-peak amplitude of oscillation (oscillator
mode) — low-frequency, low-power mode
(HGO=0)
—
0.6
—
V
Peak-to-peak amplitude of oscillation (oscillator
mode) — low-frequency, high-gain mode
(HGO=1)
—
VDD
—
V
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, low-power mode
(HGO=0)
—
0.6
—
V
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, high-gain mode
(HGO=1)
—
VDD
—
V
Series resistor — high-frequency, high-gain
mode (HGO=1)
5
Vpp
1.
2.
3.
4.
5.
VDD=3.3 V, Temperature =25 °C
See crystal or resonator manufacturer's recommendation
Cx,Cy can be provided by using either the integrated capacitors or by using external components.
When low power mode is selected, RF is integrated and must not be attached externally.
The EXTAL and XTAL pins should only be connected to required oscillator components and must not be connected to any
other devices.
6.3.2.2
Symbol
Oscillator frequency specifications
Table 17. Oscillator frequency specifications
Description
Min.
Typ.
Max.
Unit
fosc_lo
Oscillator crystal or resonator frequency — low
frequency mode (MCG_C2[RANGE]=00)
32
—
40
kHz
fosc_hi_1
Oscillator crystal or resonator frequency — high
frequency mode (low range)
(MCG_C2[RANGE]=01)
3
—
8
MHz
Notes
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
29
Peripheral operating requirements and behaviors
Table 17. Oscillator frequency specifications (continued)
Symbol
Description
Min.
Typ.
Max.
Unit
fosc_hi_2
Oscillator crystal or resonator frequency — high
frequency mode (high range)
(MCG_C2[RANGE]=1x)
8
—
32
MHz
fec_extal
Input clock frequency (external clock mode)
—
—
50
MHz
tdc_extal
Input clock duty cycle (external clock mode)
40
50
60
%
Crystal startup time — 32 kHz low-frequency,
low-power mode (HGO=0)
—
750
—
ms
Crystal startup time — 32 kHz low-frequency,
high-gain mode (HGO=1)
—
250
—
ms
Crystal startup time — 8 MHz high-frequency
(MCG_C2[RANGE]=01), low-power mode
(HGO=0)
—
0.6
—
ms
Crystal startup time — 8 MHz high-frequency
(MCG_C2[RANGE]=01), high-gain mode
(HGO=1)
—
1
—
ms
tcst
Notes
1, 2
3, 4
1. Other frequency limits may apply when external clock is being used as a reference for the FLL or PLL.
2. When transitioning from FBE to FEI mode, restrict the frequency of the input clock so that, when it is divided by FRDIV, it
remains within the limits of the DCO input clock frequency.
3. Proper PC board layout procedures must be followed to achieve specifications.
4. Crystal startup time is defined as the time between the oscillator being enabled and the OSCINIT bit in the MCG_S register
being set.
NOTE
The 32 kHz oscillator works in low power mode by default and
cannot be moved into high power/gain mode.
6.3.3 32 kHz Oscillator Electrical Characteristics
This section describes the module electrical characteristics.
6.3.3.1
32 kHz oscillator DC electrical specifications
Table 18. 32kHz oscillator DC electrical specifications
Symbol
Description
Min.
Typ.
Max.
Unit
VBAT
Supply voltage
1.71
—
3.6
V
Internal feedback resistor
—
100
—
MΩ
Cpara
RF
Parasitical capacitance of EXTAL32 and XTAL32
—
5
7
pF
Vpp1
Peak-to-peak amplitude of oscillation
—
0.6
—
V
1. When a crystal is being used with the 32 kHz oscillator, the EXTAL32 and XTAL32 pins should only be connected to
required oscillator components and must not be connected to any other devices.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
30
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
6.3.3.2
Symbol
fosc_lo
tstart
fec_extal32
32 kHz oscillator frequency specifications
Table 19. 32 kHz oscillator frequency specifications
Description
Min.
Typ.
Max.
Unit
Oscillator crystal
—
32.768
—
kHz
Crystal start-up time
—
1000
—
ms
1
Externally provided input clock frequency
—
32.768
—
kHz
2
700
—
VBAT
mV
2, 3
vec_extal32 Externally provided input clock amplitude
Notes
1. Proper PC board layout procedures must be followed to achieve specifications.
2. This specification is for an externally supplied clock driven to EXTAL32 and does not apply to any other clock input. The
oscillator remains enabled and XTAL32 must be left unconnected.
3. The parameter specified is a peak-to-peak value and VIH and VIL specifications do not apply. The voltage of the applied
clock must be within the range of VSS to VBAT.
6.4 Memories and memory interfaces
6.4.1 Flash electrical specifications
This section describes the electrical characteristics of the flash memory module.
6.4.1.1
Flash timing specifications — program and erase
The following specifications represent the amount of time the internal charge pumps are
active and do not include command overhead.
Table 20. NVM program/erase timing specifications
Symbol
Description
Min.
Typ.
Max.
Unit
thvpgm4
thversscr
Longword Program high-voltage time
—
7.5
18
μs
Sector Erase high-voltage time
—
13
113
ms
1
—
416
3616
ms
1
Notes
thversblk256k Erase Block high-voltage time for 256 KB
Notes
1. Maximum time based on expectations at cycling end-of-life.
6.4.1.2
Symbol
Flash timing specifications — commands
Table 21. Flash command timing specifications
Description
Min.
Typ.
Max.
Unit
—
—
1.7
ms
—
—
60
μs
Read 1s Block execution time
trd1blk256k
trd1sec2k
• 256 KB program/data flash
Read 1s Section execution time (flash sector)
1
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
31
Peripheral operating requirements and behaviors
Table 21. Flash command timing specifications (continued)
Symbol
Description
Min.
Typ.
Max.
Unit
Notes
tpgmchk
Program Check execution time
—
—
45
μs
1
trdrsrc
Read Resource execution time
—
—
30
μs
1
tpgm4
Program Longword execution time
—
65
145
μs
Erase Flash Block execution time
tersblk256k
tersscr
2
• 256 KB program/data flash
Erase Flash Sector execution time
—
435
3700
ms
—
14
114
ms
2
Program Section execution time
tpgmsec512
• 512 bytes flash
—
2.4
—
ms
tpgmsec1k
• 1 KB flash
—
4.7
—
ms
tpgmsec2k
• 2 KB flash
—
9.3
—
ms
trd1all
Read 1s All Blocks execution time
—
—
1.8
ms
trdonce
Read Once execution time
—
—
25
μs
tpgmonce
1
Program Once execution time
—
65
—
μs
tersall
Erase All Blocks execution time
—
870
7400
ms
2
tvfykey
Verify Backdoor Access Key execution time
—
—
30
μs
1
Swap Control execution time
tswapx01
• control code 0x01
—
200
—
μs
tswapx02
• control code 0x02
—
70
150
μs
tswapx04
• control code 0x04
—
70
150
μs
tswapx08
• control code 0x08
—
—
30
μs
1. Assumes 25 MHz flash clock frequency.
2. Maximum times for erase parameters based on expectations at cycling end-of-life.
6.4.1.3
Flash high voltage current behaviors
Table 22. Flash high voltage current behaviors
Symbol
Description
IDD_PGM
IDD_ERS
6.4.1.4
Symbol
Min.
Typ.
Max.
Unit
Average current adder during high voltage
flash programming operation
—
2.5
6.0
mA
Average current adder during high voltage
flash erase operation
—
1.5
4.0
mA
Reliability specifications
Table 23. NVM reliability specifications
Description
Min.
Typ.1
Max.
Unit
Notes
Program Flash
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
32
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 23. NVM reliability specifications (continued)
Min.
Typ.1
Max.
Unit
tnvmretp10k Data retention after up to 10 K cycles
5
50
—
years
tnvmretp1k
Data retention after up to 1 K cycles
20
100
—
years
nnvmcycp
Cycling endurance
10 K
50 K
—
cycles
Symbol
Description
Notes
2
1. Typical data retention values are based on measured response accelerated at high temperature and derated to a constant
25°C use profile. Engineering Bulletin EB618 does not apply to this technology. Typical endurance defined in Engineering
Bulletin EB619.
2. Cycling endurance represents number of program/erase cycles at -40°C ≤ Tj ≤ 125°C.
6.4.2 EzPort Switching Specifications
Table 24. EzPort switching specifications
Num
Description
Min.
Max.
Unit
Operating voltage
1.71
3.6
V
EP1
EZP_CK frequency of operation (all commands except
READ)
—
fSYS/2
MHz
EP1a
EZP_CK frequency of operation (READ command)
—
fSYS/8
MHz
EP2
EZP_CS negation to next EZP_CS assertion
2 x tEZP_CK
—
ns
EP3
EZP_CS input valid to EZP_CK high (setup)
5
—
ns
EP4
EZP_CK high to EZP_CS input invalid (hold)
5
—
ns
EP5
EZP_D input valid to EZP_CK high (setup)
2
—
ns
EP6
EZP_CK high to EZP_D input invalid (hold)
5
—
ns
EP7
EZP_CK low to EZP_Q output valid
—
16
ns
EP8
EZP_CK low to EZP_Q output invalid (hold)
0
—
ns
EP9
EZP_CS negation to EZP_Q tri-state
—
12
ns
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
33
Peripheral operating requirements and behaviors
EZP_CK
EP3
EP2
EP4
EZP_CS
EP9
EP7
EP8
EZP_Q (output)
EP5
EP6
EZP_D (input)
Figure 9. EzPort Timing Diagram
6.4.3 Flexbus Switching Specifications
All processor bus timings are synchronous; input setup/hold and output delay are given in
respect to the rising edge of a reference clock, FB_CLK. The FB_CLK frequency may be
the same as the internal system bus frequency or an integer divider of that frequency.
The following timing numbers indicate when data is latched or driven onto the external
bus, relative to the Flexbus output clock (FB_CLK). All other timing relationships can be
derived from these values.
Table 25. Flexbus limited voltage range switching specifications
Num
Description
Min.
Max.
Unit
Notes
Operating voltage
2.7
3.6
V
Frequency of operation
—
FB_CLK
MHz
FB1
Clock period
20
—
ns
FB2
Address, data, and control output valid
—
11.5
ns
1
FB3
Address, data, and control output hold
0.5
—
ns
1
FB4
Data and FB_TA input setup
8.5
—
ns
2
FB5
Data and FB_TA input hold
0.5
—
ns
2
1. Specification is valid for all FB_AD[31:0], FB_BE/BWEn, FB_CSn, FB_OE, FB_R/W,FB_TBST, FB_TSIZ[1:0], FB_ALE,
and FB_TS.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
34
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
2. Specification is valid for all FB_AD[31:0] and FB_TA.
Table 26. Flexbus full voltage range switching specifications
Num
Description
Min.
Max.
Unit
Operating voltage
1.71
3.6
V
Frequency of operation
Notes
—
FB_CLK
MHz
1/FB_CLK
—
ns
Address, data, and control output valid
—
13.5
ns
1
FB3
Address, data, and control output hold
0
—
ns
1
FB4
Data and FB_TA input setup
13.7
—
ns
2
FB5
Data and FB_TA input hold
0.5
—
ns
2
FB1
Clock period
FB2
1. Specification is valid for all FB_AD[31:0], FB_BE/BWEn, FB_CSn, FB_OE, FB_R/W,FB_TBST, FB_TSIZ[1:0], FB_ALE,
and FB_TS.
2. Specification is valid for all FB_AD[31:0] and FB_TA.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
35
Peripheral operating requirements and behaviors
FB1
FB_CLK
FB3
FB5
FB_A[Y]
Address
FB4
FB2
FB_D[X]
Address
Data
FB_RW
FB_TS
FB_ALE
AA=1
FB_CSn
AA=0
FB_OEn
FB4
FB_BEn
FB5
AA=1
FB_TA
FB_TSIZ[1:0]
AA=0
TSIZ
Figure 10. FlexBus read timing diagram
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
36
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
FB1
FB_CLK
FB2
FB3
FB_A[Y]
Address
FB_D[X]
Address
Data
FB_RW
FB_TS
FB_ALE
AA=1
FB_CSn
AA=0
FB_OEn
FB4
FB_BEn
FB5
AA=1
FB_TA
AA=0
FB_TSIZ[1:0]
TSIZ
Figure 11. FlexBus write timing diagram
6.5 Security and integrity modules
There are no specifications necessary for the device's security and integrity modules.
6.6 Analog
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
37
Peripheral operating requirements and behaviors
6.6.1 ADC electrical specifications
The 16-bit accuracy specifications listed in Table 27 and Table 28 are achievable on the
differential pins ADCx_DP0, ADCx_DM0, ADCx_DP1, ADCx_DM1, ADCx_DP3, and
ADCx_DM3.
The ADCx_DP2 and ADCx_DM2 ADC inputs are connected to the PGA outputs and are
not direct device pins. Accuracy specifications for these pins are defined in Table 29 and
Table 30.
All other ADC channels meet the 13-bit differential/12-bit single-ended accuracy
specifications.
6.6.1.1
16-bit ADC operating conditions
Table 27. 16-bit ADC operating conditions
Symbol
Description
Conditions
Min.
Typ.1
Max.
Unit
VDDA
Supply voltage
Absolute
1.71
—
3.6
V
ΔVDDA
Supply voltage
Delta to VDD (VDD - VDDA)
-100
0
+100
mV
2
ΔVSSA
Ground voltage
Delta to VSS (VSS - VSSA)
-100
0
+100
mV
2
VREFH
ADC reference
voltage high
1.13
VDDA
VDDA
V
VREFL
ADC reference
voltage low
VSSA
VSSA
VSSA
V
VADIN
Input voltage
• 16-bit differential mode
VREFL
—
31/32 *
VREFH
V
• All other modes
VREFL
—
• 16-bit mode
—
8
10
• 8-bit / 10-bit / 12-bit
modes
—
4
5
—
2
5
CADIN
RADIN
RAS
Input capacitance
Input resistance
Notes
VREFH
pF
kΩ
Analog source
resistance
13-bit / 12-bit modes
fADCK < 4 MHz
—
—
5
kΩ
fADCK
ADC conversion
clock frequency
≤ 13-bit mode
1.0
—
18.0
MHz
4
fADCK
ADC conversion
clock frequency
16-bit mode
2.0
—
12.0
MHz
4
Crate
ADC conversion
rate
≤ 13-bit modes
No ADC hardware averaging
3
5
20.000
—
818.330
Ksps
Continuous conversions
enabled, subsequent
conversion time
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
38
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 27. 16-bit ADC operating conditions (continued)
Symbol
Crate
Description
Conditions
ADC conversion
rate
16-bit mode
Min.
Typ.1
Max.
Unit
Notes
5
No ADC hardware averaging
37.037
—
461.467
Ksps
Continuous conversions
enabled, subsequent
conversion time
1. Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK = 1.0 MHz, unless otherwise stated. Typical values are for
reference only, and are not tested in production.
2. DC potential difference.
3. This resistance is external to MCU. To achieve the best results, the analog source resistance must be kept as low as
possible. The results in this data sheet were derived from a system that had < 8 Ω analog source resistance. The RAS/CAS
time constant should be kept to < 1 ns.
4. To use the maximum ADC conversion clock frequency, the ADHSC bit must be set and the ADLPC bit must be clear.
5. For guidelines and examples of conversion rate calculation, download the ADC calculator tool.
SIMPLIFIED
INPUT PIN EQUIVALENT
CIRCUIT
Z ADIN
SIMPLIFIED
CHANNEL SELECT
CIRCUIT
Pad
leakage
due to
input
protection
Z AS
R AS
ADC SAR
ENGINE
R ADIN
V ADIN
C AS
V AS
R ADIN
INPUT PIN
R ADIN
INPUT PIN
R ADIN
INPUT PIN
C ADIN
Figure 12. ADC input impedance equivalency diagram
6.6.1.2
16-bit ADC electrical characteristics
Table 28. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA)
Symbol
Description
IDDA_ADC
Supply current
Conditions1
Min.
Typ.2
Max.
Unit
Notes
0.215
—
1.7
mA
3
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
39
Peripheral operating requirements and behaviors
Table 28. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Symbol
fADACK
Description
ADC
asynchronous
clock source
Sample Time
TUE
DNL
INL
EFS
Conditions1
Min.
Typ.2
Max.
Unit
Notes
• ADLPC = 1, ADHSC = 0
1.2
2.4
3.9
MHz
• ADLPC = 1, ADHSC = 1
2.4
4.0
6.1
MHz
tADACK = 1/
fADACK
• ADLPC = 0, ADHSC = 0
3.0
5.2
7.3
MHz
• ADLPC = 0, ADHSC = 1
4.4
6.2
9.5
MHz
LSB4
5
LSB4
5
LSB4
5
LSB4
VADIN =
VDDA
See Reference Manual chapter for sample times
Total unadjusted
error
• 12-bit modes
—
±4
±6.8
• <12-bit modes
—
±1.4
±2.1
Differential nonlinearity
• 12-bit modes
—
±0.7
-1.1 to +1.9
Integral nonlinearity
Full-scale error
-0.3 to 0.5
• <12-bit modes
—
±0.2
• 12-bit modes
—
±1.0
-2.7 to +1.9
-0.7 to +0.5
• <12-bit modes
—
±0.5
• 12-bit modes
—
-4
-5.4
• <12-bit modes
—
-1.4
-1.8
5
EQ
ENOB
Quantization
error
• 16-bit modes
—
-1 to 0
—
• ≤13-bit modes
—
—
±0.5
Effective number 16-bit differential mode
of bits
• Avg = 32
• Avg = 4
LSB4
6
12.8
14.5
—
bits
11.9
13.8
—
bits
12.2
13.9
—
bits
11.4
13.1
—
bits
16-bit single-ended mode
• Avg = 32
• Avg = 4
SINAD
THD
Signal-to-noise
plus distortion
See ENOB
Total harmonic
distortion
16-bit differential mode
6.02 × ENOB + 1.76
• Avg = 32
16-bit single-ended mode
• Avg = 32
SFDR
Spurious free
dynamic range
dB
7
—
–94
—
dB
—
-85
—
dB
16-bit differential mode
• Avg = 32
16-bit single-ended mode
• Avg = 32
7
82
95
—
dB
78
90
—
dB
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
40
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 28. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Symbol
Description
EIL
Input leakage
error
Conditions1
Min.
Typ.2
Max.
IIn × RAS
Unit
Notes
mV
IIn =
leakage
current
(refer to
the MCU's
voltage
and current
operating
ratings)
VTEMP25
Temp sensor
slope
Across the full temperature
range of the device
1.55
1.62
1.69
mV/°C
Temp sensor
voltage
25 °C
706
716
726
mV
1. All accuracy numbers assume the ADC is calibrated with VREFH = VDDA
2. Typical values assume VDDA = 3.0 V, Temp = 25°C, fADCK = 2.0 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
3. The ADC supply current depends on the ADC conversion clock speed, conversion rate and the ADLPC bit (low power).
For lowest power operation the ADLPC bit must be set, the HSC bit must be clear with 1 MHz ADC conversion clock
speed.
4. 1 LSB = (VREFH - VREFL)/2N
5. ADC conversion clock < 16 MHz, Max hardware averaging (AVGE = %1, AVGS = %11)
6. Input data is 100 Hz sine wave. ADC conversion clock < 12 MHz.
7. Input data is 1 kHz sine wave. ADC conversion clock < 12 MHz.
Figure 13. Typical ENOB vs. ADC_CLK for 16-bit differential mode
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
41
Peripheral operating requirements and behaviors
Figure 14. Typical ENOB vs. ADC_CLK for 16-bit single-ended mode
6.6.1.3
16-bit ADC with PGA operating conditions
Table 29. 16-bit ADC with PGA operating conditions
Symbol
Description
Conditions
Min.
Typ.1
Max.
Unit
VDDA
Supply voltage
Absolute
1.71
—
3.6
V
VREFPGA
PGA ref voltage
VADIN
VCM
RPGAD
VREF_OU VREF_OU VREF_OU
T
T
T
V
Notes
2, 3
Input voltage
VSSA
—
VDDA
V
Input Common
Mode range
VSSA
—
VDDA
V
Gain = 1, 2, 4, 8
—
128
—
kΩ
IN+ to IN-4
Gain = 16, 32
—
64
—
Gain = 64
—
32
—
Differential input
impedance
RAS
Analog source
resistance
—
100
—
Ω
5
TS
ADC sampling
time
1.25
—
—
µs
6
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
42
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 29. 16-bit ADC with PGA operating conditions (continued)
Symbol
Crate
Description
Conditions
ADC conversion
rate
≤ 13 bit modes
Min.
Typ.1
Max.
Unit
Notes
18.484
—
450
Ksps
7
37.037
—
250
Ksps
8
No ADC hardware
averaging
Continuous conversions
enabled
Peripheral clock = 50
MHz
16 bit modes
No ADC hardware
averaging
Continuous conversions
enabled
Peripheral clock = 50
MHz
1. Typical values assume VDDA = 3.0 V, Temp = 25°C, fADCK = 6 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
2. ADC must be configured to use the internal voltage reference (VREF_OUT)
3. PGA reference is internally connected to the VREF_OUT pin. If the user wishes to drive VREF_OUT with a voltage other
than the output of the VREF module, the VREF module must be disabled.
4. For single ended configurations the input impedance of the driven input is RPGAD/2
5. The analog source resistance (RAS), external to MCU, should be kept as minimum as possible. Increased RAS causes drop
in PGA gain without affecting other performances. This is not dependent on ADC clock frequency.
6. The minimum sampling time is dependent on input signal frequency and ADC mode of operation. A minimum of 1.25µs
time should be allowed for Fin=4 kHz at 16-bit differential mode. Recommended ADC setting is: ADLSMP=1, ADLSTS=2 at
8 MHz ADC clock.
7. ADC clock = 18 MHz, ADLSMP = 1, ADLST = 00, ADHSC = 1
8. ADC clock = 12 MHz, ADLSMP = 1, ADLST = 01, ADHSC = 1
6.6.1.4
16-bit ADC with PGA characteristics
Table 30. 16-bit ADC with PGA characteristics
Symbol
Description
Conditions
IDDA_PGA
Supply current
Low power
(ADC_PGA[PGALPb]=0)
IDC_PGA
Input DC current
Min.
Typ.1
Max.
Unit
Notes
—
420
644
μA
2
A
3
Gain =1, VREFPGA=1.2V,
VCM=0.5V
—
1.54
—
μA
Gain =64, VREFPGA=1.2V,
VCM=0.1V
—
0.57
—
μA
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
43
Peripheral operating requirements and behaviors
Table 30. 16-bit ADC with PGA characteristics (continued)
Symbol
G
BW
Description
Gain4
Input signal
bandwidth
PSRR
Power supply
rejection ratio
CMRR
Common mode
rejection ratio
Min.
Typ.1
Max.
• PGAG=0
0.95
1
1.05
• PGAG=1
1.9
2
2.1
• PGAG=2
3.8
4
4.2
• PGAG=3
7.6
8
8.4
• PGAG=4
15.2
16
16.6
• PGAG=5
30.0
31.6
33.2
• PGAG=6
58.8
63.3
67.8
—
—
4
kHz
—
—
40
kHz
—
-84
—
dB
VDDA= 3V
±100mV,
fVDDA= 50Hz,
60Hz
• Gain=1
—
-84
—
dB
• Gain=64
—
-85
—
dB
VCM=
500mVpp,
fVCM= 50Hz,
100Hz
Conditions
• 16-bit modes
• < 16-bit modes
Gain=1
Unit
Notes
RAS < 100Ω
VOFS
Input offset
voltage
—
0.2
—
mV
Output offset =
VOFS*(Gain+1)
TGSW
Gain switching
settling time
—
—
10
µs
5
EIL
Input leakage
error
mV
IIn = leakage
current
All modes
IIn × RAS
(refer to the
MCU's voltage
and current
operating
ratings)
VPP,DIFF
SNR
THD
SFDR
Maximum
differential input
signal swing
V
6
16-bit
differential
mode,
Average=32
where VX = VREFPGA × 0.583
Signal-to-noise
ratio
• Gain=1
80
90
—
dB
• Gain=64
52
66
—
dB
Total harmonic
distortion
• Gain=1
85
100
—
dB
• Gain=64
49
95
—
dB
Spurious free
dynamic range
• Gain=1
85
105
—
dB
• Gain=64
53
88
—
dB
16-bit
differential
mode,
Average=32,
fin=100Hz
16-bit
differential
mode,
Average=32,
fin=100Hz
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
44
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 30. 16-bit ADC with PGA characteristics (continued)
Symbol
Description
ENOB
Effective number
of bits
SINAD
Min.
Typ.1
Max.
Unit
Notes
• Gain=1, Average=4
11.6
13.4
—
bits
• Gain=64, Average=4
7.2
9.6
—
bits
• Gain=1, Average=32
12.8
14.5
—
bits
16-bit
differential
mode,fin=100Hz
• Gain=2, Average=32
11.0
14.3
—
bits
• Gain=4, Average=32
7.9
13.8
—
bits
• Gain=8, Average=32
7.3
13.1
—
bits
• Gain=16, Average=32
6.8
12.5
—
bits
• Gain=32, Average=32
6.8
11.5
—
bits
• Gain=64, Average=32
7.5
10.6
—
bits
Conditions
Signal-to-noise
plus distortion
ratio
See ENOB
6.02 × ENOB + 1.76
dB
1. Typical values assume VDDA =3.0V, Temp=25°C, fADCK=6MHz unless otherwise stated.
2. This current is a PGA module adder, in addition to ADC conversion currents.
3. Between IN+ and IN-. The PGA draws a DC current from the input terminals. The magnitude of the DC current is a strong
function of input common mode voltage (VCM) and the PGA gain.
4. Gain = 2PGAG
5. After changing the PGA gain setting, a minimum of 2 ADC+PGA conversions should be ignored.
6. Limit the input signal swing so that the PGA does not saturate during operation. Input signal swing is dependent on the
PGA reference voltage and gain setting.
6.6.2 CMP and 6-bit DAC electrical specifications
Table 31. Comparator and 6-bit DAC electrical specifications
Symbol
Description
Min.
Typ.
Max.
Unit
VDD
Supply voltage
1.71
—
3.6
V
IDDHS
Supply current, High-speed mode (EN=1, PMODE=1)
—
—
200
μA
IDDLS
Supply current, low-speed mode (EN=1, PMODE=0)
—
—
20
μA
VAIN
Analog input voltage
VSS – 0.3
—
VDD
V
VAIO
Analog input offset voltage
—
—
20
mV
• CR0[HYSTCTR] = 00
—
5
—
mV
• CR0[HYSTCTR] = 01
—
10
—
mV
• CR0[HYSTCTR] = 10
—
20
—
mV
• CR0[HYSTCTR] = 11
—
30
—
mV
VH
Analog comparator hysteresis1
VCMPOh
Output high
VDD – 0.5
—
—
V
VCMPOl
Output low
—
—
0.5
V
Propagation delay, high-speed mode (EN=1,
PMODE=1)
20
50
200
ns
tDHS
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
45
Peripheral operating requirements and behaviors
Table 31. Comparator and 6-bit DAC electrical specifications (continued)
Symbol
tDLS
IDAC6b
Description
Min.
Typ.
Max.
Unit
Propagation delay, low-speed mode (EN=1,
PMODE=0)
80
250
600
ns
Analog comparator initialization delay2
—
—
40
μs
6-bit DAC current adder (enabled)
—
7
—
μA
INL
6-bit DAC integral non-linearity
–0.5
—
0.5
LSB3
DNL
6-bit DAC differential non-linearity
–0.3
—
0.3
LSB
1. Typical hysteresis is measured with input voltage range limited to 0.6 to VDD-0.6 V.
2. Comparator initialization delay is defined as the time between software writes to change control inputs (Writes to DACEN,
VRSEL, PSEL, MSEL, VOSEL) and the comparator output settling to a stable level.
3. 1 LSB = Vreference/64
0.08
0.07
0.06
HYSTCTR
Setting
CM P Hystereris (V)
0.05
00
0.04
01
10
11
0.03
0.02
0.01
0
0.1
0.4
0.7
1
1.3
1.6
1.9
Vin level (V)
2.2
2.5
2.8
3.1
Figure 15. Typical hysteresis vs. Vin level (VDD=3.3V, PMODE=0)
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
46
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
0.18
0.16
0.14
CMP
P Hystereris (V)
0.12
HYSTCTR
Setting
0.1
00
01
0
08
0.08
10
11
0.06
0.04
0.02
0
0.1
0.4
0.7
1
1.3
1.6
Vin level (V)
1.9
2.2
2.5
2.8
3.1
Figure 16. Typical hysteresis vs. Vin level (VDD=3.3V, PMODE=1)
6.6.3 12-bit DAC electrical characteristics
6.6.3.1
Symbol
12-bit DAC operating requirements
Table 32. 12-bit DAC operating requirements
Desciption
Min.
Max.
Unit
VDDA
Supply voltage
1.71
3.6
V
VDACR
Reference voltage
1.13
3.6
V
TA
Temperature
Operating temperature
range of the device
CL
Output load capacitance
—
100
pF
IL
Output load current
—
1
mA
Notes
1
°C
2
1. The DAC reference can be selected to be VDDA or the voltage output of the VREF module (VREF_OUT)
2. A small load capacitance (47 pF) can improve the bandwidth performance of the DAC
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
47
Peripheral operating requirements and behaviors
6.6.3.2
Symbol
12-bit DAC operating behaviors
Table 33. 12-bit DAC operating behaviors
Description
IDDA_DACL Supply current — low-power mode
Min.
Typ.
Max.
Unit
—
—
150
μA
—
—
700
μA
Notes
P
IDDA_DACH Supply current — high-speed mode
P
tDACLP
Full-scale settling time (0x080 to 0xF7F) —
low-power mode
—
100
200
μs
1
tDACHP
Full-scale settling time (0x080 to 0xF7F) —
high-power mode
—
15
30
μs
1
—
0.7
1
μs
1
—
—
100
mV
tCCDACLP Code-to-code settling time (0xBF8 to 0xC08)
— low-power mode and high-speed mode
Vdacoutl
DAC output voltage range low — high-speed
mode, no load, DAC set to 0x000
Vdacouth
DAC output voltage range high — highspeed mode, no load, DAC set to 0xFFF
VDACR
−100
—
VDACR
mV
INL
Integral non-linearity error — high speed
mode
—
—
±8
LSB
2
DNL
Differential non-linearity error — VDACR > 2
V
—
—
±1
LSB
3
DNL
Differential non-linearity error — VDACR =
VREF_OUT
—
—
±1
LSB
4
—
±0.4
±0.8
%FSR
5
Gain error
—
±0.1
±0.6
%FSR
5
Power supply rejection ratio, VDDA ≥ 2.4 V
60
—
90
dB
TCO
Temperature coefficient offset voltage
—
3.7
—
μV/C
TGE
Temperature coefficient gain error
—
0.000421
—
%FSR/C
Rop
Output resistance load = 3 kΩ
—
—
250
Ω
SR
Slew rate -80h→ F7Fh→ 80h
VOFFSET Offset error
EG
PSRR
1.
2.
3.
4.
5.
6.
V/μs
• High power (SPHP)
1.2
1.7
—
• Low power (SPLP)
0.05
0.12
—
—
—
-80
CT
Channel to channel cross talk
BW
3dB bandwidth
6
dB
kHz
• High power (SPHP)
550
—
—
• Low power (SPLP)
40
—
—
Settling within ±1 LSB
The INL is measured for 0 + 100 mV to VDACR −100 mV
The DNL is measured for 0 + 100 mV to VDACR −100 mV
The DNL is measured for 0 + 100 mV to VDACR −100 mV with VDDA > 2.4 V
Calculated by a best fit curve from VSS + 100 mV to VDACR − 100 mV
VDDA = 3.0 V, reference select set for VDDA (DACx_CO:DACRFS = 1), high power mode (DACx_C0:LPEN = 0), DAC set to
0x800, temperature range is across the full range of the device
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
48
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Figure 17. Typical INL error vs. digital code
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
49
Peripheral operating requirements and behaviors
Figure 18. Offset at half scale vs. temperature
6.6.4 Voltage reference electrical specifications
Table 34. VREF full-range operating requirements
Symbol
Description
Min.
Max.
Unit
VDDA
Supply voltage
1.71
3.6
V
TA
Temperature
CL
Output load capacitance
Operating temperature
range of the device
°C
100
nF
Notes
1, 2
1. CL must be connected to VREF_OUT if the VREF_OUT functionality is being used for either an internal or external
reference.
2. The load capacitance should not exceed +/-25% of the nominal specified CL value over the operating temperature range of
the device.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
50
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 35. VREF full-range operating behaviors
Symbol
Description
Min.
Typ.
Max.
Unit
Notes
Vout
Voltage reference output with factory trim at
nominal VDDA and temperature=25C
1.1915
1.195
1.1977
V
Vout
Voltage reference output — factory trim
1.1584
—
1.2376
V
Vstep
Voltage reference trim step
—
0.5
—
mV
Vtdrift
Temperature drift (Vmax -Vmin across the full
temperature range)
—
—
80
mV
Ibg
Bandgap only current
—
—
80
µA
1
Ilp
Low-power buffer current
—
—
360
uA
1
Ihp
High-power buffer current
—
—
1
mA
1
mV
1, 2
ΔVLOAD
Load regulation
• current = + 1.0 mA
—
2
—
• current = - 1.0 mA
—
5
—
Tstup
Buffer startup time
—
—
100
µs
Vvdrift
Voltage drift (Vmax -Vmin across the full voltage
range)
—
2
—
mV
1
1. See the chip's Reference Manual for the appropriate settings of the VREF Status and Control register.
2. Load regulation voltage is the difference between the VREF_OUT voltage with no load vs. voltage with defined load
Table 36. VREF limited-range operating requirements
Symbol
Description
Min.
Max.
Unit
TA
Temperature
0
50
°C
Notes
Table 37. VREF limited-range operating behaviors
Symbol
Vout
Description
Voltage reference output with factory trim
Min.
Max.
Unit
1.173
1.225
V
Notes
6.7 Timers
See General switching specifications.
6.8 Communication interfaces
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
51
Peripheral operating requirements and behaviors
6.8.1 CAN switching specifications
See General switching specifications.
6.8.2 DSPI switching specifications (limited voltage range)
The DMA Serial Peripheral Interface (DSPI) provides a synchronous serial bus with
master and slave operations. Many of the transfer attributes are programmable. The tables
below provide DSPI timing characteristics for classic SPI timing modes. Refer to the
DSPI chapter of the Reference Manual for information on the modified transfer formats
used for communicating with slower peripheral devices.
Table 38. Master mode DSPI timing (limited voltage range)
Num
Description
Min.
Max.
Unit
Operating voltage
2.7
3.6
V
Frequency of operation
—
25
MHz
Notes
DS1
DSPI_SCK output cycle time
2 x tBUS
—
ns
DS2
DSPI_SCK output high/low time
(tSCK/2) − 2
(tSCK/2) + 2
ns
DS3
DSPI_PCSn valid to DSPI_SCK delay
(tBUS x 2) −
2
—
ns
1
DS4
DSPI_SCK to DSPI_PCSn invalid delay
(tBUS x 2) −
2
—
ns
2
DS5
DSPI_SCK to DSPI_SOUT valid
—
8.5
ns
DS6
DSPI_SCK to DSPI_SOUT invalid
−2
—
ns
DS7
DSPI_SIN to DSPI_SCK input setup
15
—
ns
DS8
DSPI_SCK to DSPI_SIN input hold
0
—
ns
1. The delay is programmable in SPIx_CTARn[PSSCK] and SPIx_CTARn[CSSCK].
2. The delay is programmable in SPIx_CTARn[PASC] and SPIx_CTARn[ASC].
DSPI_PCSn
DS3
DS1
DS2
DS4
DSPI_SCK
(CPOL=0)
DSPI_SIN
DSPI_SOUT
DS7
DS8
Data
First data
Last data
DS5
First data
DS6
Data
Last data
Figure 19. DSPI classic SPI timing — master mode
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
52
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 39. Slave mode DSPI timing (limited voltage range)
Num
Description
Operating voltage
Min.
Max.
Unit
2.7
3.6
V
12.5
MHz
4 x tBUS
—
ns
(tSCK/2) − 2
(tSCK/2) + 2
ns
Frequency of operation
DS9
DSPI_SCK input cycle time
DS10
DSPI_SCK input high/low time
DS11
DSPI_SCK to DSPI_SOUT valid
—
10
ns
DS12
DSPI_SCK to DSPI_SOUT invalid
0
—
ns
DS13
DSPI_SIN to DSPI_SCK input setup
2
—
ns
DS14
DSPI_SCK to DSPI_SIN input hold
7
—
ns
DS15
DSPI_SS active to DSPI_SOUT driven
—
14
ns
DS16
DSPI_SS inactive to DSPI_SOUT not driven
—
14
ns
DSPI_SS
DS10
DS9
DSPI_SCK
DS15
(CPOL=0)
DSPI_SOUT
DS12
First data
DS13
DSPI_SIN
DS16
DS11
Last data
Data
DS14
First data
Data
Last data
Figure 20. DSPI classic SPI timing — slave mode
6.8.3 DSPI switching specifications (full voltage range)
The DMA Serial Peripheral Interface (DSPI) provides a synchronous serial bus with
master and slave operations. Many of the transfer attributes are programmable. The tables
below provides DSPI timing characteristics for classic SPI timing modes. Refer to the
DSPI chapter of the Reference Manual for information on the modified transfer formats
used for communicating with slower peripheral devices.
Table 40. Master mode DSPI timing (full voltage range)
Num
Description
Operating voltage
Frequency of operation
DS1
DSPI_SCK output cycle time
Min.
Max.
Unit
Notes
1
1.71
3.6
V
—
12.5
MHz
4 x tBUS
—
ns
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
53
Peripheral operating requirements and behaviors
Table 40. Master mode DSPI timing (full voltage range) (continued)
Num
Description
Min.
Max.
Unit
Notes
DS2
DSPI_SCK output high/low time
(tSCK/2) - 4
(tSCK/2) + 4
ns
DS3
DSPI_PCSn valid to DSPI_SCK delay
(tBUS x 2) −
4
—
ns
2
DS4
DSPI_SCK to DSPI_PCSn invalid delay
(tBUS x 2) −
4
—
ns
3
DS5
DSPI_SCK to DSPI_SOUT valid
—
10
ns
DS6
DSPI_SCK to DSPI_SOUT invalid
-4.5
—
ns
DS7
DSPI_SIN to DSPI_SCK input setup
20.5
—
ns
DS8
DSPI_SCK to DSPI_SIN input hold
0
—
ns
1. The DSPI module can operate across the entire operating voltage for the processor, but to run across the full voltage
range the maximum frequency of operation is reduced.
2. The delay is programmable in SPIx_CTARn[PSSCK] and SPIx_CTARn[CSSCK].
3. The delay is programmable in SPIx_CTARn[PASC] and SPIx_CTARn[ASC].
DSPI_PCSn
DS3
DS1
DS2
DS4
DSPI_SCK
DS8
DS7
(CPOL=0)
DSPI_SIN
Data
First data
Last data
DS5
DSPI_SOUT
First data
DS6
Data
Last data
Figure 21. DSPI classic SPI timing — master mode
Table 41. Slave mode DSPI timing (full voltage range)
Num
Description
Operating voltage
Frequency of operation
Min.
Max.
Unit
1.71
3.6
V
—
6.25
MHz
8 x tBUS
—
ns
DS9
DSPI_SCK input cycle time
DS10
DSPI_SCK input high/low time
(tSCK/2) - 4
(tSCK/2) + 4
ns
DS11
DSPI_SCK to DSPI_SOUT valid
—
20
ns
DS12
DSPI_SCK to DSPI_SOUT invalid
0
—
ns
DS13
DSPI_SIN to DSPI_SCK input setup
2
—
ns
DS14
DSPI_SCK to DSPI_SIN input hold
7
—
ns
DS15
DSPI_SS active to DSPI_SOUT driven
—
19
ns
DS16
DSPI_SS inactive to DSPI_SOUT not driven
—
19
ns
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
54
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
DSPI_SS
DS10
DS9
DSPI_SCK
DS15
(CPOL=0)
DSPI_SOUT
DS12
First data
DS13
DSPI_SIN
DS16
DS11
Last data
Data
DS14
First data
Data
Last data
Figure 22. DSPI classic SPI timing — slave mode
6.8.4 Inter-Integrated Circuit Interface (I2C) timing
Table 42. I 2C timing
Characteristic
Symbol
Standard Mode
Fast Mode
Unit
Minimum
Maximum
Minimum
Maximum
SCL Clock Frequency
fSCL
0
100
0
400
kHz
Hold time (repeated) START condition.
After this period, the first clock pulse is
generated.
tHD; STA
4
—
0.6
—
µs
LOW period of the SCL clock
tLOW
4.7
—
1.3
—
µs
HIGH period of the SCL clock
tHIGH
4
—
0.6
—
µs
Set-up time for a repeated START
condition
tSU; STA
4.7
—
0.6
—
µs
Data hold time for I2C bus devices
tHD; DAT
01
3.452
03
0.91
µs
tSU; DAT
2504
—
1002, 5
Data set-up time
—
ns
6
Rise time of SDA and SCL signals
tr
—
1000
20 +0.1Cb
300
ns
Fall time of SDA and SCL signals
tf
—
300
20 +0.1Cb5
300
ns
Set-up time for STOP condition
tSU; STO
4
—
0.6
—
µs
Bus free time between STOP and
START condition
tBUF
4.7
—
1.3
—
µs
Pulse width of spikes that must be
suppressed by the input filter
tSP
N/A
N/A
0
50
ns
1. The master mode I2C deasserts ACK of an address byte simultaneously with the falling edge of SCL. If no slaves
acknowledge this address byte, then a negative hold time can result, depending on the edge rates of the SDA and SCL
lines.
2. The maximum tHD; DAT must be met only if the device does not stretch the LOW period (tLOW) of the SCL signal.
3. Input signal Slew = 10ns and Output Load = 50pf
4. Set-up time in slave-transmitter mode is 1 IPBus clock period, if the TX FIFO is empty.
5. A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but the requirement tSU; DAT ≥ 250 ns must
then be met. This is automatically the case if the device does not stretch the LOW period of the SCL signal. If such a
device does stretch the LOW period of the SCL signal, then it must output the next data bit to the SDA line trmax + tSU; DAT
= 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification) before the SCL line is released.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
55
Peripheral operating requirements and behaviors
6. Cb = total capacitance of the one bus line in pF.
SDA
tf
tLOW
tSU; DAT
tr
tf
tHD; STA
tr
tSP
tBUF
SCL
S
tHD; STA
tHD; DAT
tHIGH
tSU; STA
tSU; STO
SR
P
S
Figure 23. Timing definition for fast and standard mode devices on the I2C bus
6.8.5 UART switching specifications
See General switching specifications.
6.8.6 SDHC specifications
The following timing specs are defined at the chip I/O pin and must be translated
appropriately to arrive at timing specs/constraints for the physical interface.
Table 43. SDHC switching specifications
Num
Symbol
Description
Min.
Max.
Unit
Card input clock
SD1
fpp
Clock frequency (low speed)
0
400
kHz
fpp
Clock frequency (SD\SDIO full speed\high speed)
0
25\50
MHz
fpp
Clock frequency (MMC full speed\high speed)
0
20\50
MHz
fOD
Clock frequency (identification mode)
0
400
kHz
SD2
tWL
Clock low time
7
—
ns
SD3
tWH
Clock high time
7
—
ns
SD4
tTLH
Clock rise time
—
3
ns
SD5
tTHL
Clock fall time
—
3
ns
SDHC output / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK)
SD6
tOD
SDHC output delay (output valid)
-5
8.3
ns
SDHC input / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK)
SD7
tISU
SDHC input setup time
5
—
ns
SD8
tIH
SDHC input hold time
0
—
ns
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
56
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
SD3
SD2
SD1
SDHC_CLK
SD6
Output SDHC_CMD
Output SDHC_DAT[3:0]
SD7
SD8
Input SDHC_CMD
Input SDHC_DAT[3:0]
Figure 24. SDHC timing
6.8.7 I2S switching specifications
This section provides the AC timings for the I2S in master (clocks driven) and slave
modes (clocks input). All timings are given for non-inverted serial clock polarity
(TCR[TSCKP] = 0, RCR[RSCKP] = 0) and a non-inverted frame sync (TCR[TFSI] = 0,
RCR[RFSI] = 0). If the polarity of the clock and/or the frame sync have been inverted, all
the timings remain valid by inverting the clock signal (I2S_BCLK) and/or the frame sync
(I2S_FS) shown in the figures below.
Table 44. I2S master mode timing (limited voltage range)
Num
Description
Min.
Max.
Unit
Operating voltage
2.7
3.6
V
S1
I2S_MCLK cycle time
S2
I2S_MCLK pulse width high/low
S3
I2S_BCLK cycle time
S4
I2S_BCLK pulse width high/low
S5
I2S_BCLK to I2S_FS output valid
S6
I2S_BCLK to I2S_FS output invalid
S7
S8
2 x tSYS
ns
45%
55%
MCLK period
5 x tSYS
—
ns
45%
55%
BCLK period
—
15
ns
-2.5
—
ns
I2S_BCLK to I2S_TXD valid
—
15
ns
I2S_BCLK to I2S_TXD invalid
-3
—
ns
S9
I2S_RXD/I2S_FS input setup before I2S_BCLK
20
—
ns
S10
I2S_RXD/I2S_FS input hold after I2S_BCLK
0
—
ns
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
57
Peripheral operating requirements and behaviors
S1
S2
S2
I2S_MCLK (output)
S3
I2S_BCLK (output)
S4
S4
S6
S5
I2S_FS (output)
S10
S9
I2S_FS (input)
S7
S8
S7
S8
I2S_TXD
S9
S10
I2S_RXD
Figure 25. I2S timing — master mode
Table 45. I2S slave mode timing (limited voltage range)
Num
Description
Min.
Max.
Unit
Operating voltage
2.7
3.6
V
8 x tSYS
—
ns
S11
I2S_BCLK cycle time (input)
S12
I2S_BCLK pulse width high/low (input)
45%
55%
MCLK period
S13
I2S_FS input setup before I2S_BCLK
10
—
ns
S14
I2S_FS input hold after I2S_BCLK
3
—
ns
S15
I2S_BCLK to I2S_TXD/I2S_FS output valid
—
20
ns
S16
I2S_BCLK to I2S_TXD/I2S_FS output invalid
0
—
ns
S17
I2S_RXD setup before I2S_BCLK
10
—
ns
S18
I2S_RXD hold after I2S_BCLK
2
—
ns
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
58
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
S11
S12
I2S_BCLK (input)
S12
S15
S16
I2S_FS (output)
S13
S14
I2S_FS (input)
S15
S16
S15
S16
I2S_TXD
S17
S18
I2S_RXD
Figure 26. I2S timing — slave modes
Table 46. I2S master mode timing (full voltage range)
Num
Description
Min.
Max.
Unit
Operating voltage
1.71
3.6
V
S1
I2S_MCLK cycle time
S2
I2S_MCLK pulse width high/low
S3
I2S_BCLK cycle time
S4
I2S_BCLK pulse width high/low
S5
I2S_BCLK to I2S_FS output valid
S6
I2S_BCLK to I2S_FS output invalid
S7
I2S_BCLK to I2S_TXD valid
S8
2 x tSYS
45%
ns
55%
MCLK period
5 x tSYS
—
ns
45%
55%
BCLK period
—
15
ns
-4.3
—
ns
—
15
ns
I2S_BCLK to I2S_TXD invalid
-4.6
—
ns
S9
I2S_RXD/I2S_FS input setup before I2S_BCLK
23.9
—
ns
S10
I2S_RXD/I2S_FS input hold after I2S_BCLK
0
—
ns
Table 47. I2S slave mode timing (full voltage range)
Num
Description
Min.
Max.
Unit
Operating voltage
1.71
3.6
V
8 x tSYS
—
ns
S11
I2S_BCLK cycle time (input)
S12
I2S_BCLK pulse width high/low (input)
45%
55%
MCLK period
S13
I2S_FS input setup before I2S_BCLK
10
—
ns
S14
I2S_FS input hold after I2S_BCLK
3.5
—
ns
S15
I2S_BCLK to I2S_TXD/I2S_FS output valid
—
28.6
ns
S16
I2S_BCLK to I2S_TXD/I2S_FS output invalid
0
—
ns
S17
I2S_RXD setup before I2S_BCLK
10
—
ns
S18
I2S_RXD hold after I2S_BCLK
2
—
ns
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
59
Peripheral operating requirements and behaviors
6.9 Human-machine interfaces (HMI)
6.9.1 TSI electrical specifications
Table 48. TSI electrical specifications
Symbol
Description
Min.
Typ.
Max.
Unit
VDDTSI
Operating voltage
1.71
—
3.6
V
CELE
Notes
Target electrode capacitance range
1
20
500
pF
1
fREFmax
Reference oscillator frequency
—
5.5
12.7
MHz
2
fELEmax
Electrode oscillator frequency
—
0.5
4.0
MHz
3
Internal reference capacitor
0.5
1
1.2
pF
Oscillator delta voltage
100
600
760
mV
4
—
1.133
1.5
μA
3,5
—
36
50
—
1.133
1.5
μA
3,6
—
36
50
CREF
VDELTA
IREF
IELE
Reference oscillator current source base current
• 1uA setting (REFCHRG=0)
• 32uA setting (REFCHRG=31)
Electrode oscillator current source base current
• 1uA setting (EXTCHRG=0)
• 32uA setting (EXTCHRG=31)
Pres5
Electrode capacitance measurement precision
—
8.3333
38400
fF/count
7
Pres20
Electrode capacitance measurement precision
—
8.3333
38400
fF/count
8
Pres100
Electrode capacitance measurement precision
—
8.3333
38400
fF/count
9
0.003
12.5
—
fF/count
10
Resolution
—
—
16
bits
Response time @ 20 pF
8
15
25
μs
Current added in run mode
—
55
—
μA
Low power mode current adder
—
1.3
2.5
μA
MaxSens Maximum sensitivity
Res
TCon20
ITSI_RUN
ITSI_LP
11
12
1. The TSI module is functional with capacitance values outside this range. However, optimal performance is not guaranteed.
2. CAPTRM=7, DELVOL=7, and fixed external capacitance of 20 pF.
3. CAPTRM=0, DELVOL=2, and fixed external capacitance of 20 pF.
4. CAPTRM=0, EXTCHRG=9, and fixed external capacitance of 20 pF.
5. The programmable current source value is generated by multiplying the SCANC[REFCHRG] value and the base current.
6. The programmable current source value is generated by multiplying the SCANC[EXTCHRG] value and the base current.
7. Measured with a 5 pF electrode, reference oscillator frequency of 10 MHz, PS = 128, NSCN = 8; Iext = 16.
8. Measured with a 20 pF electrode, reference oscillator frequency of 10 MHz, PS = 128, NSCN = 2; Iext = 16.
9. Measured with a 20 pF electrode, reference oscillator frequency of 10 MHz, PS = 16, NSCN = 3; Iext = 16.
10. Sensitivity defines the minimum capacitance change when a single count from the TSI module changes, it is equal to (Cref
* Iext)/( Iref * PS * NSCN). Sensitivity depends on the configuration used. The typical value listed is based on the following
configuration: Iext = 5 μA, EXTCHRG = 4, PS = 128, NSCN = 2, Iref = 16 μA, REFCHRG = 15, Cref = 1.0 pF. The
minimum sensitivity describes the smallest possible capacitance that can be measured by a single count (this is the best
sensitivity but is described as a minimum because it’s the smallest number). The minimum sensitivity parameter is based
on the following configuration: Iext = 1 μA, EXTCHRG = 0, PS = 128, NSCN = 32, Iref = 32 μA, REFCHRG = 31, Cref= 0.5
pF
11. Time to do one complete measurement of the electrode. Sensitivity resolution of 0.0133 pF, PS = 0, NSCN = 0, 1
electrode, DELVOL = 2, EXTCHRG = 15.
12. CAPTRM=7, DELVOL=2, REFCHRG=0, EXTCHRG=4, PS=7, NSCN=0F, LPSCNITV=F, LPO is selected (1 kHz), and
fixed external capacitance of 20 pF. Data is captured with an average of 7 periods window.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
60
Freescale Semiconductor, Inc.
Dimensions
7 Dimensions
7.1 Obtaining package dimensions
Package dimensions are provided in package drawings.
To find a package drawing, go to freescale.com and perform a keyword search for the
drawing’s document number:
If you want the drawing for this package
Then use this document number
144-pin LQFP
98ASS23177W
144-pin MAPBGA
98ASA00222D
8 Pinout
8.1 K10 Signal Multiplexing and Pin Assignments
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The Port Control Module is responsible
for selecting which ALT functionality is available on each pin.
144 144
LQFP MAP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
—
L5
RESERVED
RESERVED
RESERVED
—
M5
NC
NC
NC
—
A10
NC
NC
NC
—
B10
NC
NC
NC
—
C10
NC
NC
NC
1
D3
PTE0
ADC1_SE4a
ADC1_SE4a
PTE0
SPI1_PCS1
UART1_TX
SDHC0_D1
I2C1_SDA
2
D2
PTE1/
LLWU_P0
ADC1_SE5a
ADC1_SE5a
PTE1/
LLWU_P0
SPI1_SOUT
UART1_RX
SDHC0_D0
I2C1_SCL
3
D1
PTE2/
LLWU_P1
ADC1_SE6a
ADC1_SE6a
PTE2/
LLWU_P1
SPI1_SCK
UART1_CTS_ SDHC0_DCLK
b
4
E4
PTE3
ADC1_SE7a
ADC1_SE7a
PTE3
SPI1_SIN
UART1_RTS_ SDHC0_CMD
b
5
E5
VDD
VDD
VDD
6
F6
VSS
VSS
VSS
ALT7
EzPort
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
61
Pinout
144 144
LQFP MAP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
7
E3
PTE4/
LLWU_P2
DISABLED
PTE4/
LLWU_P2
SPI1_PCS0
UART3_TX
SDHC0_D3
8
E2
PTE5
DISABLED
PTE5
SPI1_PCS2
UART3_RX
SDHC0_D2
9
E1
PTE6
DISABLED
PTE6
SPI1_PCS3
UART3_CTS_ I2S0_MCLK
b
10
F4
PTE7
DISABLED
PTE7
UART3_RTS_ I2S0_RXD
b
11
F3
PTE8
DISABLED
PTE8
UART5_TX
I2S0_RX_FS
12
F2
PTE9
DISABLED
PTE9
UART5_RX
I2S0_RX_
BCLK
13
F1
PTE10
DISABLED
PTE10
UART5_CTS_ I2S0_TXD
b
14
G4
PTE11
DISABLED
PTE11
UART5_RTS_ I2S0_TX_FS
b
15
G3
PTE12
DISABLED
PTE12
16
E6
VDD
VDD
VDD
17
F7
VSS
VSS
VSS
18
H1
PTE16
ADC0_SE4a
ADC0_SE4a
PTE16
SPI0_PCS0
UART2_TX
FTM_CLKIN0
FTM0_FLT3
19
H2
PTE17
ADC0_SE5a
ADC0_SE5a
PTE17
SPI0_SCK
UART2_RX
FTM_CLKIN1
LPT0_ALT3
20
G1
PTE18
ADC0_SE6a
ADC0_SE6a
PTE18
SPI0_SOUT
UART2_CTS_ I2C0_SDA
b
21
G2
PTE19
ADC0_SE7a
ADC0_SE7a
PTE19
SPI0_SIN
UART2_RTS_ I2C0_SCL
b
22
H3
VSS
VSS
VSS
23
J1
ADC0_DP1
ADC0_DP1
ADC0_DP1
24
J2
ADC0_DM1
ADC0_DM1
ADC0_DM1
25
K1
ADC1_DP1
ADC1_DP1
ADC1_DP1
26
K2
ADC1_DM1
ADC1_DM1
ADC1_DM1
27
L1
PGA0_DP/
ADC0_DP0/
ADC1_DP3
PGA0_DP/
ADC0_DP0/
ADC1_DP3
PGA0_DP/
ADC0_DP0/
ADC1_DP3
28
L2
PGA0_DM/
ADC0_DM0/
ADC1_DM3
PGA0_DM/
ADC0_DM0/
ADC1_DM3
PGA0_DM/
ADC0_DM0/
ADC1_DM3
29
M1
PGA1_DP/
ADC1_DP0/
ADC0_DP3
PGA1_DP/
ADC1_DP0/
ADC0_DP3
PGA1_DP/
ADC1_DP0/
ADC0_DP3
30
M2
PGA1_DM/
ADC1_DM0/
ADC0_DM3
PGA1_DM/
ADC1_DM0/
ADC0_DM3
PGA1_DM/
ADC1_DM0/
ADC0_DM3
31
H5
VDDA
VDDA
VDDA
32
G5
VREFH
VREFH
VREFH
33
G6
VREFL
VREFL
VREFL
34
H6
VSSA
VSSA
VSSA
ALT7
EzPort
I2S0_CLKIN
I2S0_TX_
BCLK
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
62
Freescale Semiconductor, Inc.
Pinout
144 144
LQFP MAP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
35
K3
ADC1_SE16/
CMP2_IN2/
ADC0_SE22
ADC1_SE16/
CMP2_IN2/
ADC0_SE22
ADC1_SE16/
CMP2_IN2/
ADC0_SE22
36
J3
ADC0_SE16/
CMP1_IN2/
ADC0_SE21
ADC0_SE16/
CMP1_IN2/
ADC0_SE21
ADC0_SE16/
CMP1_IN2/
ADC0_SE21
37
M3
VREF_OUT/
CMP1_IN5/
CMP0_IN5/
ADC1_SE18
VREF_OUT/
CMP1_IN5/
CMP0_IN5/
ADC1_SE18
VREF_OUT/
CMP1_IN5/
CMP0_IN5/
ADC1_SE18
38
L3
DAC0_OUT/
CMP1_IN3/
ADC0_SE23
DAC0_OUT/
CMP1_IN3/
ADC0_SE23
DAC0_OUT/
CMP1_IN3/
ADC0_SE23
39
L4
DAC1_OUT/
CMP2_IN3/
ADC1_SE23
DAC1_OUT/
CMP2_IN3/
ADC1_SE23
DAC1_OUT/
CMP2_IN3/
ADC1_SE23
40
M7
XTAL32
XTAL32
XTAL32
41
M6
EXTAL32
EXTAL32
EXTAL32
42
L6
VBAT
VBAT
VBAT
43
—
VDD
VDD
VDD
44
—
VSS
VSS
VSS
45
M4
PTE24
ADC0_SE17
ADC0_SE17
PTE24
CAN1_TX
UART4_TX
EWM_OUT_b
46
K5
PTE25
ADC0_SE18
ADC0_SE18
PTE25
CAN1_RX
UART4_RX
EWM_IN
47
K4
PTE26
DISABLED
PTE26
UART4_CTS_
b
RTC_CLKOUT
48
J4
PTE27
DISABLED
PTE27
UART4_RTS_
b
49
H4
PTE28
DISABLED
PTE28
50
J5
PTA0
JTAG_TCLK/
SWD_CLK/
EZP_CLK
TSI0_CH1
PTA0
UART0_CTS_ FTM0_CH5
b
JTAG_TCLK/
SWD_CLK
EZP_CLK
51
J6
PTA1
JTAG_TDI/
EZP_DI
TSI0_CH2
PTA1
UART0_RX
FTM0_CH6
JTAG_TDI
EZP_DI
52
K6
PTA2
JTAG_TDO/ TSI0_CH3
TRACE_SWO/
EZP_DO
PTA2
UART0_TX
FTM0_CH7
JTAG_TDO/ EZP_DO
TRACE_SWO
53
K7
PTA3
JTAG_TMS/
SWD_DIO
TSI0_CH4
PTA3
UART0_RTS_ FTM0_CH0
b
54
L7
PTA4/
LLWU_P3
NMI_b/
EZP_CS_b
TSI0_CH5
PTA4/
LLWU_P3
FTM0_CH1
55
M8
PTA5
DISABLED
PTA5
FTM0_CH2
56
E7
VDD
VDD
VDD
57
G7
VSS
VSS
VSS
58
J7
PTA6
DISABLED
PTA6
FTM0_CH3
TRACE_
CLKOUT
59
J8
PTA7
ADC0_SE10
PTA7
FTM0_CH4
TRACE_D3
ADC0_SE10
JTAG_TMS/
SWD_DIO
NMI_b
CMP2_OUT
I2S0_RX_
BCLK
EZP_CS_b
JTAG_TRST
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
63
Pinout
144 144
LQFP MAP
BGA
Pin Name
Default
60
K8
PTA8
ADC0_SE11
61
L8
PTA9
62
M9
63
ALT0
ADC0_SE11
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
PTA8
FTM1_CH0
FTM1_QD_
PHA
TRACE_D2
DISABLED
PTA9
FTM1_CH1
FTM1_QD_
PHB
TRACE_D1
PTA10
DISABLED
PTA10
FTM2_CH0
FTM2_QD_
PHA
TRACE_D0
L9
PTA11
DISABLED
PTA11
FTM2_CH1
FTM2_QD_
PHB
64
K9
PTA12
CMP2_IN0
CMP2_IN0
PTA12
CAN0_TX
FTM1_CH0
I2S0_TXD
FTM1_QD_
PHA
65
J9
PTA13/
LLWU_P4
CMP2_IN1
CMP2_IN1
PTA13/
LLWU_P4
CAN0_RX
FTM1_CH1
I2S0_TX_FS
FTM1_QD_
PHB
66
L10
PTA14
DISABLED
PTA14
SPI0_PCS0
UART0_TX
I2S0_TX_
BCLK
67
L11
PTA15
DISABLED
PTA15
SPI0_SCK
UART0_RX
I2S0_RXD
68
K10
PTA16
DISABLED
PTA16
SPI0_SOUT
UART0_CTS_
b
I2S0_RX_FS
69
K11
PTA17
ADC1_SE17
ADC1_SE17
PTA17
SPI0_SIN
UART0_RTS_
b
I2S0_MCLK
70
E8
VDD
VDD
VDD
71
G8
VSS
VSS
VSS
72
M12 PTA18
EXTAL
EXTAL
PTA18
FTM0_FLT2
FTM_CLKIN0
73
M11 PTA19
XTAL
XTAL
PTA19
FTM1_FLT0
FTM_CLKIN1
74
L12
RESET_b
RESET_b
RESET_b
75
K12
PTA24
DISABLED
PTA24
FB_A29
76
J12
PTA25
DISABLED
PTA25
FB_A28
77
J11
PTA26
DISABLED
PTA26
FB_A27
78
J10
PTA27
DISABLED
PTA27
FB_A26
79
H12
PTA28
DISABLED
PTA28
FB_A25
80
H11
PTA29
DISABLED
PTA29
FB_A24
81
H10
PTB0/
LLWU_P5
ADC0_SE8/
ADC1_SE8/
TSI0_CH0
ADC0_SE8/
ADC1_SE8/
TSI0_CH0
PTB0/
LLWU_P5
I2C0_SCL
FTM1_CH0
FTM1_QD_
PHA
82
H9
PTB1
ADC0_SE9/
ADC1_SE9/
TSI0_CH6
ADC0_SE9/
ADC1_SE9/
TSI0_CH6
PTB1
I2C0_SDA
FTM1_CH1
FTM1_QD_
PHB
83
G12
PTB2
ADC0_SE12/
TSI0_CH7
ADC0_SE12/
TSI0_CH7
PTB2
I2C0_SCL
UART0_RTS_
b
FTM0_FLT3
84
G11
PTB3
ADC0_SE13/
TSI0_CH8
ADC0_SE13/
TSI0_CH8
PTB3
I2C0_SDA
UART0_CTS_
b
FTM0_FLT0
85
G10
PTB4
ADC1_SE10
ADC1_SE10
PTB4
FTM1_FLT0
86
G9
PTB5
ADC1_SE11
ADC1_SE11
PTB5
FTM2_FLT0
87
F12
PTB6
ADC1_SE12
ADC1_SE12
PTB6
FB_AD23
88
F11
PTB7
ADC1_SE13
ADC1_SE13
PTB7
FB_AD22
EzPort
I2S0_CLKIN
LPT0_ALT1
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
64
Freescale Semiconductor, Inc.
Pinout
144 144
LQFP MAP
BGA
Pin Name
Default
ALT0
ALT1
89
F10
PTB8
PTB8
90
F9
PTB9
PTB9
91
E12
PTB10
ADC1_SE14
ADC1_SE14
92
E11
PTB11
ADC1_SE15
ADC1_SE15
93
H7
VSS
VSS
VSS
94
F5
VDD
VDD
VDD
95
E10
PTB16
TSI0_CH9
96
E9
PTB17
97
D12
PTB18
98
D11
PTB19
99
D10
100
101
102
ALT2
ALT3
ALT4
ALT5
ALT6
UART3_RTS_
b
FB_AD21
SPI1_PCS1
UART3_CTS_
b
FB_AD20
PTB10
SPI1_PCS0
UART3_RX
FB_AD19
FTM0_FLT1
PTB11
SPI1_SCK
UART3_TX
FB_AD18
FTM0_FLT2
TSI0_CH9
PTB16
SPI1_SOUT
UART0_RX
FB_AD17
EWM_IN
TSI0_CH10
TSI0_CH10
PTB17
SPI1_SIN
UART0_TX
FB_AD16
EWM_OUT_b
TSI0_CH11
TSI0_CH11
PTB18
CAN0_TX
FTM2_CH0
I2S0_TX_
BCLK
FB_AD15
FTM2_QD_
PHA
TSI0_CH12
TSI0_CH12
PTB19
CAN0_RX
FTM2_CH1
I2S0_TX_FS
FB_OE_b
FTM2_QD_
PHB
PTB20
PTB20
SPI2_PCS0
FB_AD31
CMP0_OUT
D9
PTB21
PTB21
SPI2_SCK
FB_AD30
CMP1_OUT
C12
PTB22
PTB22
SPI2_SOUT
FB_AD29
CMP2_OUT
C11
PTB23
PTB23
SPI2_SIN
SPI0_PCS5
FB_AD28
103
B12
PTC0
ADC0_SE14/
TSI0_CH13
ADC0_SE14/
TSI0_CH13
PTC0
SPI0_PCS4
PDB0_EXTRG I2S0_TXD
FB_AD14
104
B11
PTC1/
LLWU_P6
ADC0_SE15/
TSI0_CH14
ADC0_SE15/
TSI0_CH14
PTC1/
LLWU_P6
SPI0_PCS3
UART1_RTS_ FTM0_CH0
b
FB_AD13
105
A12
PTC2
ADC0_SE4b/
CMP1_IN0/
TSI0_CH15
ADC0_SE4b/
CMP1_IN0/
TSI0_CH15
PTC2
SPI0_PCS2
UART1_CTS_ FTM0_CH1
b
FB_AD12
106
A11
PTC3/
LLWU_P7
CMP1_IN1
CMP1_IN1
PTC3/
LLWU_P7
SPI0_PCS1
UART1_RX
FTM0_CH2
FB_CLKOUT
107
H8
VSS
VSS
VSS
108
—
VDD
VDD
VDD
109
A9
PTC4/
LLWU_P8
PTC4/
LLWU_P8
SPI0_PCS0
UART1_TX
FTM0_CH3
FB_AD11
CMP1_OUT
110
D8
PTC5/
LLWU_P9
PTC5/
LLWU_P9
SPI0_SCK
LPT0_ALT2
FB_AD10
CMP0_OUT
111
C8
PTC6/
LLWU_P10
CMP0_IN0
CMP0_IN0
PTC6/
LLWU_P10
SPI0_SOUT
112
B8
PTC7
CMP0_IN1
CMP0_IN1
PTC7
SPI0_SIN
113
A8
PTC8
ADC1_SE4b/
CMP0_IN2
ADC1_SE4b/
CMP0_IN2
PTC8
114
D7
PTC9
ADC1_SE5b/
CMP0_IN3
ADC1_SE5b/
CMP0_IN3
PTC9
115
C7
PTC10
ADC1_SE6b/
CMP0_IN4
ADC1_SE6b/
CMP0_IN4
PTC10
116
B7
PTC11/
LLWU_P11
ADC1_SE7b
ADC1_SE7b
PTC11/
LLWU_P11
PDB0_EXTRG
ALT7
EzPort
FB_AD9
FB_AD8
I2S0_MCLK
I2S0_CLKIN
FB_AD7
I2S0_RX_
BCLK
FB_AD6
I2C1_SCL
I2S0_RX_FS
FB_AD5
I2C1_SDA
I2S0_RXD
FB_RW_b
FTM2_FLT0
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
65
Pinout
144 144
LQFP MAP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
117
A7
PTC12
PTC12
UART4_RTS_
b
FB_AD27
118
D6
PTC13
PTC13
UART4_CTS_
b
FB_AD26
119
C6
PTC14
PTC14
UART4_RX
FB_AD25
120
B6
PTC15
PTC15
UART4_TX
FB_AD24
121
—
VSS
VSS
VSS
122
—
VDD
VDD
VDD
123
A6
PTC16
PTC16
CAN1_RX
UART3_RX
FB_CS5_b/
FB_TSIZ1/
FB_BE23_16_
b
124
D5
PTC17
PTC17
CAN1_TX
UART3_TX
FB_CS4_b/
FB_TSIZ0/
FB_BE31_24_
b
125
C5
PTC18
PTC18
UART3_RTS_
b
FB_TBST_b/
FB_CS2_b/
FB_BE15_8_b
126
B5
PTC19
PTC19
UART3_CTS_
b
FB_CS3_b/
FB_BE7_0_b
127
A5
PTD0/
LLWU_P12
PTD0/
LLWU_P12
SPI0_PCS0
UART2_RTS_
b
FB_ALE/
FB_CS1_b/
FB_TS_b
128
D4
PTD1
PTD1
SPI0_SCK
UART2_CTS_
b
FB_CS0_b
129
C4
PTD2/
LLWU_P13
PTD2/
LLWU_P13
SPI0_SOUT
UART2_RX
FB_AD4
130
B4
PTD3
PTD3
SPI0_SIN
UART2_TX
FB_AD3
131
A4
PTD4/
LLWU_P14
PTD4/
LLWU_P14
SPI0_PCS1
UART0_RTS_ FTM0_CH4
b
FB_AD2
EWM_IN
132
A3
PTD5
ADC0_SE6b
ADC0_SE6b
PTD5
SPI0_PCS2
UART0_CTS_ FTM0_CH5
b
FB_AD1
EWM_OUT_b
133
A2
PTD6/
LLWU_P15
ADC0_SE7b
ADC0_SE7b
PTD6/
LLWU_P15
SPI0_PCS3
UART0_RX
FTM0_CH6
FB_AD0
FTM0_FLT0
134
M10 VSS
VSS
VSS
135
F8
VDD
VDD
VDD
136
A1
PTD7
PTD7
CMT_IRO
UART0_TX
FTM0_CH7
137
C9
PTD8
DISABLED
PTD8
I2C0_SCL
UART5_RX
FB_A16
138
B9
PTD9
DISABLED
PTD9
I2C0_SDA
UART5_TX
FB_A17
139
B3
PTD10
DISABLED
PTD10
UART5_RTS_
b
FB_A18
140
B2
PTD11
DISABLED
PTD11
SPI2_PCS0
UART5_CTS_ SDHC0_
b
CLKIN
FB_A19
141
B1
PTD12
DISABLED
PTD12
SPI2_SCK
SDHC0_D4
FB_A20
142
C3
PTD13
DISABLED
PTD13
SPI2_SOUT
SDHC0_D5
FB_A21
ADC0_SE5b
ADC0_SE5b
ALT7
EzPort
FB_TA_b
FTM0_FLT1
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
66
Freescale Semiconductor, Inc.
Pinout
144 144
LQFP MAP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
143
C2
PTD14
DISABLED
PTD14
SPI2_SIN
SDHC0_D6
FB_A22
144
C1
PTD15
DISABLED
PTD15
SPI2_PCS1
SDHC0_D7
FB_A23
ALT7
EzPort
8.2 K10 Pinouts
The below figure shows the pinout diagram for the devices supported by this document.
Many signals may be multiplexed onto a single pin. To determine what signals can be
used on which pin, see the previous section.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
67
PTD15
PTD14
PTD13
PTD12
PTD11
PTD10
PTD9
PTD8
PTD7
VDD
VSS
PTD6
PTD5
PTD4
PTD3
PTD2
PTD1
PTD0
PTC19
PTC18
PTC17
PTC16
VDD
VSS
PTC15
PTC14
PTC13
PTC12
PTC11
PTC10
PTC9
PTC8
PTC7
PTC6
PTC5
PTC4
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
Pinout
PTE0
1
108
VDD
PTE1
2
107
VSS
PTE2
3
106
PTC3
PTE3
4
105
PTC2
VDD
5
104
PTC1
VSS
6
103
PTC0
PTE4
7
102
PTB23
PTE5
8
101
PTB22
PTE6
9
100
PTB21
PTE7
10
99
PTB20
RESET_b
ADC0_SE16/CMP1_IN2/ADC0_SE21
36
73
PTA19
72
74
PTA18
35
71
PTA24
ADC1_SE16/CMP2_IN2/ADC0_SE22
VSS
75
70
34
VDD
PTA25
VSSA
69
PTA26
76
PTA17
77
33
68
32
VREFL
PTA16
VREFH
67
PTA27
PTA15
78
66
31
PTA14
PTA28
VDDA
65
79
PTA13
30
64
PTA29
PGA1_DM/ADC1_DM0/ADC0_DM3
PTA12
80
63
29
PTA11
PTB0
PGA1_DP/ADC1_DP0/ADC0_DP3
62
81
PTA10
28
61
PTB1
PGA0_DM/ADC0_DM0/ADC1_DM3
PTA9
82
60
27
PTA8
PTB2
PGA0_DP/ADC0_DP0/ADC1_DP3
59
83
PTA7
26
58
PTB3
ADC1_DM1
PTA6
84
57
25
VSS
PTB4
ADC1_DP1
56
85
VDD
24
55
PTB5
ADC0_DM1
PTA5
86
54
23
PTA4
PTB6
ADC0_DP1
53
87
PTA3
22
52
PTB7
VSS
PTA2
88
51
21
PTA1
PTB8
PTE19
50
89
PTA0
20
49
PTB9
PTE18
PTE28
90
48
19
PTE27
PTB10
PTE17
47
91
PTE26
18
46
PTB11
PTE16
PTE25
92
45
17
PTE24
VSS
VSS
44
93
VSS
16
43
VDD
VDD
VDD
94
42
15
VBAT
PTB16
PTE12
41
95
EXTAL32
14
40
PTB17
PTE11
XTAL32
96
39
13
DAC1_OUT/CMP2_IN3/ADC1_SE23
PTB18
PTE10
38
PTB19
97
37
98
12
DAC0_OUT/CMP1_IN3/ADC0_SE23
11
VREF_OUT/CMP1_IN5/
CMP0_IN5/ADC1_SE18
PTE8
PTE9
Figure 27. K10 144 LQFP Pinout Diagram
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
68
Freescale Semiconductor, Inc.
Revision History
1
2
3
4
5
6
7
8
9
10
11
12
A
PTD7
PTD6
PTD5
PTD4
PTD0
PTC16
PTC12
PTC8
PTC4
NC
PTC3
PTC2
A
B
PTD12
PTD11
PTD10
PTD3
PTC19
PTC15
PTC11
PTC7
PTD9
NC
PTC1
PTC0
B
C
PTD15
PTD14
PTD13
PTD2
PTC18
PTC14
PTC10
PTC6
PTD8
NC
PTB23
PTB22
C
D
PTE2
PTE1
PTE0
PTD1
PTC17
PTC13
PTC9
PTC5
PTB21
PTB20
PTB19
PTB18
D
E
PTE6
PTE5
PTE4
PTE3
VDD
VDD
VDD
VDD
PTB17
PTB16
PTB11
PTB10
E
F
PTE10
PTE9
PTE8
PTE7
VDD
VSS
VSS
VDD
PTB9
PTB8
PTB7
PTB6
F
G
PTE18
PTE19
PTE12
PTE11
VREFH
VREFL
VSS
VSS
PTB5
PTB4
PTB3
PTB2
G
H
PTE16
PTE17
VSS
PTE28
VDDA
VSSA
VSS
VSS
PTB1
PTB0
PTA29
PTA28
H
J
ADC0_DP1
ADC0_DM1
PTE27
PTA0
PTA1
PTA6
PTA7
PTA13
PTA27
PTA26
PTA25
J
PTE26
PTE25
PTA2
PTA3
PTA8
PTA12
PTA16
PTA17
PTA24
K
RESERVED
VBAT
PTA4
PTA9
PTA11
PTA14
PTA15
RESET_b
L
M
ADC0_SE16/
CMP1_IN2/
ADC0_SE21
ADC1_SE16/
K
ADC1_DP1
CMP2_IN2/
ADC1_DM1
ADC0_SE22
PGA0_DP/
PGA0_DM/
DAC0_OUT/
ADC0_DP0/
ADC0_DM0/
CMP1_IN3/
CMP2_IN3/
ADC1_DP3
ADC1_DM3
ADC0_SE23
ADC1_SE23
PGA1_DP/
M ADC1_DP0/
ADC0_DP3
PGA1_DM/
ADC1_DM0/
ADC0_DM3
VREF_OUT/
CMP1_IN5/
CMP0_IN5/
ADC1_SE18
PTE24
NC
EXTAL32
XTAL32
PTA5
PTA10
VSS
PTA19
PTA18
2
3
4
5
6
7
8
9
10
11
12
L
1
DAC1_OUT/
Figure 28. K10 144 MAPBGA Pinout Diagram
9 Revision History
The following table provides a revision history for this document.
Table 49. Revision History
Rev. No.
Date
1
11/2010
Substantial Changes
Initial public revision
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
69
Revision History
Table 49. Revision History (continued)
Rev. No.
Date
Substantial Changes
2
3/2011
Many updates throughout
3
3/2011
Added sections that were inadvertently removed in previous revision
4
3/2011
Reworded IIC footnote in "Voltage and Current Operating Requirements" table.
Added paragraph to "Peripheral operating requirements and behaviors" section.
Added "JTAG full voltage range electricals" table to the "JTAG electricals" section.
5
6/2011
• Changed supported part numbers per new part number scheme
• Changed DC injection current specs in "Voltage and current operating requirements"
table
• Changed Input leakage current and internal pullup/pulldown resistor specs in "Voltage
and current operating behaviors" table
• Split Low power stop mode current specs by temperature range in "Power
consumption operating behaviors" table
• Changed typical IDD_VBAT spec in "Power consumption operating behaviors" table
• Added LPTMR clock specs to "Device clock specifications" table
• Changed Minimum external reset pulse width in "General switching specifications"
table
• Changed PLL operating current in "MCG specifications" table
• Added footnote to PLL period jitter in "MCG specifications" table
• Changed Supply current in "Oscillator DC electrical specifications" table
• Changed Crystal startup time in "Oscillator frequency specifications" table
• Changed Operating voltage in "EzPort switching specifications" table
• Changed title of "FlexBus switching specifications" table and added Output valid and
hold specs
• Added "FlexBus full range switching specifications" table
• Changed ADC asynchronous clock source specs in "16-bit ADC characteristics" table
• Changed Gain spec in "16-bit ADC with PGA characteristics" table
• Added typical Input DC current to "16-bit ADC with PGA characteristics" table
• Changed Input offset voltage and ENOB notes field in "16-bit ADC with PGA
characteristics" table
• Changed Analog comparator initialization delay in "Comparator and 6-bit DAC
electrical specifications"
• Changed Code-to-code settling time, DAC output voltage range low, and Temperature
coefficient offset voltage in "12-bit DAC operating behaviors" table
• Changed Temperature drift and Load regulation in "VREF full-range operating
behaviors" table
• Changed DSPI_SCK cycle time specs in "DSPI timing" tables
• Changed DSPI_SS specs in "Slave mode DSPI timing (low-speed mode)" table
• Changed DSPI_SCK to DSPI_SOUT valid spec in "Slave mode DSPI timing (highspeed mode)" table
• Changed Reference oscillator current source base current spec and added Low-power
current adder footer in "TSI electrical specifications" table
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
70
Freescale Semiconductor, Inc.
Revision History
Table 49. Revision History (continued)
Rev. No.
Date
6
01/2012
Substantial Changes
•
•
•
•
•
•
•
•
•
7
02/2013
Added AC electrical specifications.
Replaced TBDs with silicon data throughout.
In "Power mode transition operating behaviors" table, removed entry times.
Updated "EMC radiated emissions operating behaviors" to remove SAE level and also
added data for 144LQFP.
Clarified "EP7" in "EzPort switching specifications" table and "EzPort Timing Diagram".
Added "ENOB vs. ADC_CLK for 16-bit differential and 16-bit single-ended modes"
figures.
Updated IDD_RUN numbers in 'Power consumption operating behaviors' section.
Clarified 'Diagram: Typical IDD_RUN operating behavior' section and updated 'Run
mode supply current vs. core frequency — all peripheral clocks disabled' figure.
In 'Voltage reference electrical specifications' section, updated CL, Vtdrift, and Vvdrift
values.
•
•
•
•
•
•
•
•
In "ESD handling ratings", added a note for ILAT.
Updated "Voltage and current operating requirements".
Updated "Voltage and current operating behaviors".
Updated "Power mode transition operating behaviors".
Updated "EMC radiated emissions operating behaviors" to add MAPBGA data.
In "MCG specifications", updated the description of fints_t.
In "16-bit ADC operating conditions", updated the max spec of VADIN.
In "16-bit ADC electrical characteristics", updated the temp sensor slope and voltage
specs.
• Updated "I2C switching specifications".
• In "SDHC specifications", removed the operating voltage limits and updated the SD1
and SD6 specs.
• In "I2S switching specifications", added separate specification tables for the full
operating voltage range.
K10 Sub-Family Data Sheet Data Sheet, Rev. 7, 02/2013.
Freescale Semiconductor, Inc.
71
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
+1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 10 5879 8000
[email protected]
Document Number: K10P144M100SF2
Rev. 7, 02/2013
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductors products. There are no express or implied
copyright licenses granted hereunder to design or fabricate any integrated circuits or
integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to any
products herein. Freescale Semiconductor makes no warranty, representation, or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any liability, including without limitation
consequential or incidental damages. "Typical" parameters that may be provided in
Freescale Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating parameters,
including "Typicals", must be validated for each customer application by customer's
technical experts. Freescale Semiconductor does not convey any license under its patent
rights nor the rights of others. Freescale Semiconductor products are not designed,
intended, or authorized for use as components in systems intended for surgical implant
into the body, or other applications intended to support or sustain life, or for any other
application in which failure of the Freescale Semiconductor product could create a
situation where personal injury or death may occur. Should Buyer purchase or use
Freescale Semiconductor products for any such unintended or unauthorized application,
Buyer shall indemnify Freescale Semiconductor and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury
or death associated with such unintended or unauthorized use, even if such claims alleges
that Freescale Semiconductor was negligent regarding the design or manufacture of
the part.
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and
electrical characteristics as their non-RoHS-complaint and/or non-Pb-free counterparts.
For further information, see http://www.freescale.com or contact your Freescale
sales representative.
For information on Freescale's Environmental Products program, go to
http://www.freescale.com/epp.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© 2011–2013 Freescale Semiconductor, Inc.