AD ADSP-2186MBCA-266 Dsp microcomputer Datasheet

a
DSP
Microcomputer
ADSP-2186M
FEATURES
Performance
13.3 ns Instruction Cycle Time @ 2.5 V (Internal),
75 MIPS Sustained Performance
Single-Cycle Instruction Execution
Single-Cycle Context Switch
3-Bus Architecture Allows Dual Operand Fetches in
Every Instruction Cycle
Multifunction Instructions
Power-Down Mode Featuring Low CMOS Standby Power
Dissipation with 200 CLKIN Cycle Recovery from
Power-Down Condition
Low Power Dissipation in Idle Mode
System Interface
Flexible I/O Structure Allows 2.5 V or 3.3 V Operation;
All Inputs Tolerate up to 3.6 V Regardless of Mode
16-Bit Internal DMA Port for High-Speed Access to
On-Chip Memory (Mode Selectable)
4 MByte Memory Interface for Storage of Data Tables
and Program Overlays (Mode Selectable)
8-Bit DMA to Byte Memory for Transparent Program
and Data Memory Transfers (Mode Selectable)
I/O Memory Interface with 2048 Locations Supports
Parallel Peripherals (Mode Selectable)
Programmable Memory Strobe and Separate I/O
Memory Space Permits “Glueless” System Design
Programmable Wait State Generation
Two Double-Buffered Serial Ports with Companding
Hardware and Automatic Data Buffering
Automatic Booting of On-Chip Program Memory from
Byte-Wide External Memory, e.g., EPROM, or
through Internal DMA Port
Six External Interrupts
13 Programmable Flag Pins Provide Flexible System
Signaling
UART Emulation through Software SPORT Reconfiguration
ICE-Port™ Emulator Interface Supports Debugging in
Final Systems
Integration
ADSP-2100 Family Code Compatible (Easy to Use
Algebraic Syntax), with Instruction Set Extensions
40K Bytes of On-Chip RAM, Configured as
8K Words Program Memory RAM
8K Words Data Memory RAM
Dual-Purpose Program Memory for Both Instruction and
Data Storage
Independent ALU, Multiplier/Accumulator, and Barrel
Shifter Computational Units
Two Independent Data Address Generators
Powerful Program Sequencer Provides Zero Overhead
Looping Conditional Instruction Execution
Programmable 16-Bit Interval Timer with Prescaler
100-Lead LQFP and 144-Ball Mini-BGA
FUNCTIONAL BLOCK DIAGRAM
POWER-DOWN
CONTROL
FULL MEMORY MODE
MEMORY
DATA ADDRESS
GENERATORS
DAG1
DAG2
PROGRAM
SEQUENCER
PROGRAM
MEMORY
8K ⴛ 24 BIT
DATA
MEMORY
8K ⴛ 16 BIT
PROGRAMMABLE
I/O
AND
FLAGS
EXTERNAL
ADDRESS
BUS
EXTERNAL
DATA
BUS
PROGRAM MEMORY ADDRESS
BYTE DMA
CONTROLLER
DATA MEMORY ADDRESS
PROGRAM MEMORY DATA
OR
DATA MEMORY DATA
ARITHMETIC UNITS
ALU
MAC
SHIFTER
SERIAL PORTS
SPORT0
ADSP-2100 BASE
ARCHITECTURE
SPORT1
TIMER
EXTERNAL
DATA
BUS
INTERNAL
DMA
PORT
HOST MODE
ICE-Port is a trademark of Analog Devices, Inc.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
ADSP-2186M
TABLE OF CONTENTS
RECOMMENDED OPERATING CONDITIONS . . . . .
ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . .
ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . .
TIMING SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .
GENERAL NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIMING NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MEMORY TIMING SPECIFICATIONS . . . . . . . . . . . .
FREQUENCY DEPENDENCY FOR
TIMING SPECIFICATIONS . . . . . . . . . . . . . . . . . . . .
ENVIRONMENTAL CONDITIONS . . . . . . . . . . . . . . .
POWER DISSIPATION . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Drive Currents . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacitive Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TEST CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Disable Time . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Enable Time . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Signals and Reset . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupts and Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Request–Bus Grant . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDMA Address Latch . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDMA Write, Short Write Cycle . . . . . . . . . . . . . . . . . .
IDMA Write, Long Write Cycle . . . . . . . . . . . . . . . . . . .
IDMA Read, Long Read Cycle . . . . . . . . . . . . . . . . . . .
IDMA Read, Short Read Cycle . . . . . . . . . . . . . . . . . . .
IDMA Read, Short Read Cycle in Short Read
Only Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100-LEAD LQFP PIN CONFIGURATION . . . . . . . . . .
LQFP Package Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . .
144-Ball Mini-BGA Package Pinout . . . . . . . . . . . . . . . . .
Mini-BGA Package Pinout . . . . . . . . . . . . . . . . . . . . . . . .
OUTLINE DIMENSIONS
100-Lead Metric Thin Plastic Quad Flatpack
(LQFP) (ST-100) . . . . . . . . . . . . . . . . . . . . . . . . . . .
OUTLINE DIMENSIONS
144-Ball Mini-BGA (CA-144) . . . . . . . . . . . . . . . . . . . .
ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FUNCTIONAL BLOCK DIAGRAM . . . . . . . . . . . . . . . . 1
GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 3
DEVELOPMENT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . 3
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ARCHITECTURE OVERVIEW . . . . . . . . . . . . . . . . . . . . 4
Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Common-Mode Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Memory Interface Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Full Memory Mode Pins (Mode C = 0) . . . . . . . . . . . . . . 7
Host Mode Pins (Mode C = 1) . . . . . . . . . . . . . . . . . . . . 7
Terminating Unused Pins . . . . . . . . . . . . . . . . . . . . . . . . 8
Pin Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
LOW POWER OPERATION . . . . . . . . . . . . . . . . . . . . . . . 9
Power-Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Slow Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SYSTEM INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MODES OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . 11
Setting Memory Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Passive Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Active Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
IACK Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MEMORY ARCHITECTURE . . . . . . . . . . . . . . . . . . . . . 12
Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Memory Mapped Registers (New to the
ADSP-2186M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
I/O Space (Full Memory Mode) . . . . . . . . . . . . . . . . . . . 13
Composite Memory Select (CMS) . . . . . . . . . . . . . . . . . 14
Byte Memory Select (BMS) . . . . . . . . . . . . . . . . . . . . . . 14
Byte Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Byte Memory DMA (BDMA, Full Memory Mode) . . . . 14
Internal Memory DMA Port
(IDMA Port; Host Memory Mode) . . . . . . . . . . . . . . 15
Bootstrap Loading (Booting) . . . . . . . . . . . . . . . . . . . . . 15
IDMA Port Booting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Bus Request and Bus Grant . . . . . . . . . . . . . . . . . . . . . . 16
Flag I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Instruction Set Description . . . . . . . . . . . . . . . . . . . . . . 16
DESIGNING AN EZ-ICE-COMPATIBLE SYSTEM . . . 16
Target Board Connector for EZ-ICE Probe . . . . . . . . . . 17
Target Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . 17
PM, DM, BM, IOM, AND CM . . . . . . . . . . . . . . . . . . . . 17
Target System Interface Signals . . . . . . . . . . . . . . . . . . . 17
18
18
19
19
19
19
19
20
20
20
20
21
22
22
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
40
Tables
Table I. Interrupt Priority and Interrupt
Vector Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table II. Modes of Operation . . . . . . . . . . . . . . . . . . . . . . 11
Table III. PMOVLAY Bits . . . . . . . . . . . . . . . . . . . . . . . . 12
Table IV. DMOVLAY Bits . . . . . . . . . . . . . . . . . . . . . . . . 13
Table V. Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table VI. Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . 14
–2–
REV. 0
ADSP-2186M
GENERAL DESCRIPTION
The ADSP-2186M is a single-chip microcomputer optimized
for digital signal processing (DSP) and other high-speed numeric
processing applications.
The ADSP-2186M combines the ADSP-2100 family base architecture (three computational units, data address generators, and
a program sequencer) with two serial ports, a 16-bit internal DMA
port, a byte DMA port, a programmable timer, Flag I/O, extensive interrupt capabilities, and on-chip program and data memory.
The ADSP-2186M integrates 40K bytes of on-chip memory
configured as 8K words (24-bit) of program RAM, and 8K
words (16-bit) of data RAM. Power-down circuitry is also provided to meet the low power needs of battery-operated portable
equipment. The ADSP-2186M is available in a 100-lead LQFP
package and 144 Ball Mini-BGA.
In addition, the ADSP-2186M supports new instructions, which
include bit manipulations—bit set, bit clear, bit toggle, bit test—
new ALU constants, new multiplication instruction (× squared),
biased rounding, result-free ALU operations, I/O memory transfers, and global interrupt masking, for increased flexibility.
Fabricated in a high-speed, low-power, CMOS process, the
ADSP-2186M operates with a 13.3 ns instruction cycle time.
Every instruction can execute in a single processor cycle.
The ADSP-2186M’s flexible architecture and comprehensive
instruction set allow the processor to perform multiple operations in parallel. In one processor cycle, the ADSP-2186M can:
•
•
•
•
•
Generate the next program address
Fetch the next instruction
Perform one or two data moves
Update one or two data address pointers
Perform a computational operation
This takes place while the processor continues to:
•
•
•
•
Receive and transmit data through the two serial ports
Receive and/or transmit data through the internal DMA port
Receive and/or transmit data through the byte DMA port
Decrement timer
DEVELOPMENT SYSTEM
The ADSP-2100 Family Development Software, a complete set
of tools for software and hardware system development, supports
the ADSP-2186M. The System Builder provides a high-level
method for defining the architecture of systems under development. The Assembler has an algebraic syntax that is easy to
program and debug. The Linker combines object files into an
executable file. The Simulator provides an interactive instructionlevel simulation with a reconfigurable user interface to display
different portions of the hardware environment.
The EZ-KIT Lite is a hardware/software kit offering a complete
evaluation environment for the ADSP-218x family: an ADSP2189M-based evaluation board with PC monitor software plus
assembler, linker, simulator, and PROM splitter software. The
ADSP-2189M EZ-KIT Lite is a low cost, easy to use hardware
platform on which you can quickly get started with your DSP
software design. The EZ-KIT Lite includes the following features:
•
•
•
•
•
•
The ADSP-218x EZ-ICE® Emulator aids in the hardware
debugging of an ADSP-2186M system. The ADSP-2186M
integrates on-chip emulation support with a 14-pin ICE-Port
interface. This interface provides a simpler target board connection that requires fewer mechanical clearance considerations
than other ADSP-2100 Family EZ-ICEs. The ADSP-2186M
device need not be removed from the target system when using
the EZ-ICE, nor are any adapters needed. Due to the small
footprint of the EZ-ICE connector, emulation can be supported
in final board designs.
The EZ-ICE performs a full range of functions, including:
•
•
•
•
•
•
•
•
In-target operation
Up to 20 breakpoints
Single-step or full-speed operation
Registers and memory values can be examined and altered
PC upload and download functions
Instruction-level emulation of program booting and execution
Complete assembly and disassembly of instructions
C source-level debugging
See Designing An EZ-ICE-Compatible Target System in the
ADSP-2100 Family EZ-Tools Manual (ADSP-2181 sections) as
well as the Designing an EZ-ICE-Compatible System section of
this data sheet for the exact specifications of the EZ-ICE target
board connector.
Additional Information
This data sheet provides a general overview of ADSP-2186M
functionality. For additional information on the architecture and
instruction set of the processor, refer to the ADSP-2100 Family
User’s Manual. For more information about the development
tools, refer to the ADSP-2100 Family Development Tools
data sheet.
EZ-ICE is a registered trademark of Analog Devices, Inc.
REV. 0
75 MHz ADSP-2189M
Full 16-Bit Stereo Audio I/O with AD73322 Codec
RS-232 Interface
EZ-ICE Connector for Emulator Control
DSP Demo Programs
Evaluation Suite of VisualDSP
–3–
ADSP-2186M
POWER-DOWN
CONTROL
FULL MEMORY MODE
MEMORY
DATA ADDRESS
GENERATORS
DAG1
DAG2
PROGRAM
SEQUENCER
PROGRAM
MEMORY
8K ⴛ 24 BIT
DATA
MEMORY
8K ⴛ 16 BIT
PROGRAMMABLE
I/O
AND
FLAGS
EXTERNAL
ADDRESS
BUS
EXTERNAL
DATA
BUS
PROGRAM MEMORY ADDRESS
BYTE DMA
CONTROLLER
DATA MEMORY ADDRESS
PROGRAM MEMORY DATA
OR
DATA MEMORY DATA
ARITHMETIC UNITS
ALU
MAC
SHIFTER
SERIAL PORTS
SPORT0
TIMER
SPORT1
ADSP-2100 BASE
ARCHITECTURE
EXTERNAL
DATA
BUS
INTERNAL
DMA
PORT
HOST MODE
Figure 1. Functional Block Diagram
(indirect addressing), it is post-modified by the value of one of
four possible modify registers. A length value may be associated
with each pointer to implement automatic modulo addressing
for circular buffers.
ARCHITECTURE OVERVIEW
The ADSP-2186M instruction set provides flexible data moves
and multifunction (one or two data moves with a computation)
instructions. Every instruction can be executed in a single
processor cycle. The ADSP-2186M assembly language uses an
algebraic syntax for ease of coding and readability. A comprehensive set of development tools supports program development.
Efficient data transfer is achieved with the use of five
internal buses:
•
•
•
•
•
Figure 1 is an overall block diagram of the ADSP-2186M. The
processor contains three independent computational units:
the ALU, the multiplier/accumulator (MAC), and the shifter.
The computational units process 16-bit data directly and have
provisions to support multiprecision computations. The ALU
performs a standard set of arithmetic and logic operations;
division primitives are also supported. The MAC performs
single-cycle multiply, multiply/add, and multiply/subtract operations with 40 bits of accumulation. The shifter performs logical
and arithmetic shifts, normalization, denormalization, and
derive exponent operations.
Program Memory Address (PMA) Bus
Program Memory Data (PMD) Bus
Data Memory Address (DMA) Bus
Data Memory Data (DMD) Bus
Result (R) Bus
The two address buses (PMA and DMA) share a single external
address bus, allowing memory to be expanded off-chip, and the
two data buses (PMD and DMD) share a single external data
bus. Byte memory space and I/O memory space also share the
external buses.
Program memory can store both instructions and data, permitting the ADSP-2186M to fetch two operands in a single cycle,
one from program memory and one from data memory. The
ADSP-2186M can fetch an operand from program memory and
the next instruction in the same cycle.
The shifter can be used to efficiently implement numeric
format control, including multiword and block floating-point
representations.
The internal result (R) bus connects the computational units so
that the output of any unit may be the input of any unit on the
next cycle.
In lieu of the address and data bus for external memory connection, the ADSP-2186M may be configured for 16-bit Internal
DMA port (IDMA port) connection to external systems. The
IDMA port is made up of 16 data/address pins and five control
pins. The IDMA port provides transparent, direct access to the
DSPs on-chip program and data RAM.
A powerful program sequencer and two dedicated data address
generators ensure efficient delivery of operands to these computational units. The sequencer supports conditional jumps, subroutine
calls, and returns in a single cycle. With internal loop counters
and loop stacks, the ADSP-2186M executes looped code with
zero overhead; no explicit jump instructions are required to
maintain loops.
An interface to low-cost byte-wide memory is provided by the
Byte DMA port (BDMA port). The BDMA port is bidirectional
and can directly address up to four megabytes of external RAM
or ROM for off-chip storage of program overlays or data tables.
Two data address generators (DAGs) provide addresses for
simultaneous dual operand fetches (from data memory and
program memory). Each DAG maintains and updates four
address pointers. Whenever the pointer is used to access data
The byte memory and I/O memory space interface supports slow
memories and I/O memory-mapped peripherals with programmable wait state generation. External devices can gain control of
–4–
REV. 0
ADSP-2186M
external buses with bus request/grant signals (BR, BGH, and BG).
One execution mode (Go Mode) allows the ADSP-2186M to
continue running from on-chip memory. Normal execution
mode requires the processor to halt while buses are granted.
The ADSP-2186M can respond to eleven interrupts. There can
be up to six external interrupts (one edge-sensitive, two levelsensitive, and three configurable) and seven internal interrupts
generated by the timer, the serial ports (SPORTs), the Byte DMA
port, and the power-down circuitry. There is also a master
RESET signal. The two serial ports provide a complete synchronous serial interface with optional companding in hardware and
a wide variety of framed or frameless data transmit and receive
modes of operation.
Each port can generate an internal programmable serial clock or
accept an external serial clock.
The ADSP-2186M provides up to 13 general-purpose flag pins.
The data input and output pins on SPORT1 can be alternatively
configured as an input flag and an output flag. In addition, eight
flags are programmable as inputs or outputs, and three flags are
always outputs.
A programmable interval timer generates periodic interrupts.
A 16-bit count register (TCOUNT) decrements every n processor cycle, where n is a scaling value stored in an 8-bit register
(TSCALE). When the value of the count register reaches zero,
an interrupt is generated and the count register is reloaded from
a 16-bit period register (TPERIOD).
Serial Ports
The ADSP-2186M incorporates two complete synchronous
serial ports (SPORT0 and SPORT1) for serial communications
and multiprocessor communication.
Here is a brief list of the capabilities of the ADSP-2186M
SPORTs. For additional information on Serial Ports, refer to
the ADSP-2100 Family User’s Manual.
• SPORTs can use an external serial clock or generate their
own serial clock internally.
• SPORTs have independent framing for the receive and transmit sections. Sections run in a frameless mode or with frame
synchronization signals internally or externally generated.
Frame sync signals are active high or inverted, with either of
two pulsewidths and timings.
• SPORTs support serial data word lengths from 3 to 16 bits
and provide optional A-law and µ-law companding according
to CCITT recommendation G.711.
• SPORT receive and transmit sections can generate unique
interrupts on completing a data word transfer.
• SPORTs can receive and transmit an entire circular buffer of
data with only one overhead cycle per data word. An interrupt
is generated after a data buffer transfer.
• SPORT0 has a multichannel interface to selectively receive
and transmit a 24 or 32 word, time- division multiplexed,
serial bitstream.
• SPORT1 can be configured to have two external interrupts
(IRQ0 and IRQ1) and the FI and FO signals. The internally
generated serial clock may still be used in this configuration.
PIN DESCRIPTIONS
The ADSP-2186M is available in a 100-lead LQFP package
and a 144-Ball Mini-BGA package. In order to maintain maximum functionality and reduce package size and pin count, some
serial port, programmable flag, interrupt and external bus pins
have dual, multiplexed functionality. The external bus pins are
configured during RESET only, while serial port pins are software configurable during program execution. Flag and interrupt
functionality is retained concurrently on multiplexed pins. In
cases where pin functionality is reconfigurable, the default state is
shown in plain text; alternate functionality is shown in italics.
• SPORTs are bidirectional and have a separate, doublebuffered transmit and receive section.
REV. 0
–5–
ADSP-2186M
Common-Mode Pins
Pin Name
# of Pins
I/O
Function
RESET
BR
BG
BGH
DMS
PMS
IOMS
BMS
CMS
RD
WR
1
1
1
1
1
1
1
1
1
1
1
I
I
O
O
O
O
O
O
O
O
O
Processor Reset Input
Bus Request Input
Bus Grant Output
Bus Grant Hung Output
Data Memory Select Output
Program Memory Select Output
Memory Select Output
Byte Memory Select Output
Combined Memory Select Output
Memory Read Enable Output
Memory Write Enable Output
IRQ2
PF7
1
I
I/O
Edge- or Level-Sensitive Interrupt Request1
Programmable I/O Pin
IRQL1
PF6
1
I
I/O
Level-Sensitive Interrupt Requests1
Programmable I/O Pin
IRQL0
PF5
1
I
I/O
Level-Sensitive Interrupt Requests1
Programmable I/O Pin
IRQE
PF4
1
I
I/O
Edge-Sensitive Interrupt Requests1
Programmable I/O Pin
Mode D
PF3
1
I
I/O
Mode Select Input—Checked Only During RESET
Programmable I/O Pin During Normal Operation
Mode C
PF2
1
I
I/O
Mode Select Input—Checked Only During RESET
Programmable I/O Pin During Normal Operation
Mode B
PF1
1
I
I/O
Mode Select Input—Checked Only During RESET
Programmable I/O Pin During Normal Operation
Mode A
PF0
1
I
I/O
Mode Select Input—Checked Only During RESET
Programmable I/O Pin During Normal Operation
CLKIN, XTAL
CLKOUT
SPORT0
SPORT1
IRQ1:0, FI, FO
PWD
PWDACK
FL0, FL1, FL2
VDDINT
VDDEXT
GND
VDDINT
VDDEXT
GND
EZ-Port
2
1
5
5
I
O
I/O
I/O
1
1
3
2
4
10
4
7
20
9
I
O
O
I
I
I
I
I
I
I/O
Clock or Quartz Crystal Input
Processor Clock Output
Serial Port I/O Pins
Serial Port I/O Pins
Edge- or Level-Sensitive Interrupts, FI, FO2
Power-Down Control Input
Power-Down Control Output
Output Flags
Internal VDD (2.5 V) Power (LQFP)
External VDD (2.5 V or 3.3 V) Power (LQFP)
Ground (LQFP)
Internal VDD (2.5 V) Power (Mini-BGA)
External VDD (2.5 V or 3.3 V) Power (Mini-BGA)
Ground (Mini-BGA)
For Emulation Use
NOTES
1
Interrupt/Flag pins retain both functions concurrently. If IMASK is set to enable the corresponding interrupts, then the DSP will vector to the appropriate interrupt
vector address when the pin is asserted, either by external devices, or set as a programmable flag.
2
SPORT configuration determined by the DSP System Control Register. Software configurable.
–6–
REV. 0
ADSP-2186M
Memory Interface Pins
The ADSP-2186M processor can be used in one of two modes: Full Memory Mode, which allows BDMA operation with full external overlay memory and I/O capability, or Host Mode, which allows IDMA operation with limited external addressing capabilities.
The operating mode is determined by the state of the Mode C pin during RESET and cannot be changed while the processor is running.
The following tables list the active signals at specific pins of the DSP during either of the two operating modes (Full Memory or
Host). A signal in one table shares a pin with a signal from the other table, with the active signal determined by the mode set. For the
shared pins and their alternate signals (e.g., A4/IAD3), refer to the package pinout tables.
Full Memory Mode Pins (Mode C = 0)
Pin Name
# of Pins
I/O
Function
A13:0
D23:0
14
24
O
I/O
Address Output Pins for Program, Data, Byte, and I/O Spaces
Data I/O Pins for Program, Data, Byte, and I/O Spaces (8 MSBs are also
used as Byte Memory Addresses.)
Host Mode Pins (Mode C = 1)
Pin Name
# of Pins
I/O
Function
IAD15:0
A0
D23:8
IWR
16
1
16
1
1
1
1
1
I/O
O
I/O
I
I
I
I
O
IDMA Port Address/Data Bus
Address Pin for External I/O, Program, Data, or Byte Access1
Data I/O Pins for Program, Data, Byte, and I/O Spaces
IDMA Write Enable
IDMA Read Enable
IDMA Address Latch Pin
IDMA Select
IDMA Port Acknowledge Configurable in Mode D; Open Drain
IRD
IAL
IS
IACK
NOTE
1
In Host Mode, external peripheral addresses can be decoded using the A0, CMS, PMS, DMS, and IOMS signals.
REV. 0
–7–
ADSP-2186M
Terminating Unused Pins
The following table shows the recommendations for terminating unused pins.
Pin Terminations
Pin Name
XTAL
CLKOUT
A13:1 or
IAD12:0
A0
D23:8
D7 or
IWR
D6 or
IRD
D5 or
IAL
D4 or
IS
D3 or
IACK
D2:0 or
IAD15:13
PMS
DMS
BMS
IOMS
CMS
RD
WR
BR
BG
BGH
IRQ2/PF7
IRQL1/PF6
IRQL0/PF5
IRQE/PF4
SCLK0
RFS0
DR0
TFS0
DT0
SCLK1
RFS1/IRQ0
DR1/FI
TFS1/IRQ1
DT1/FO
EE
EBR
EBG
ERESET
EMS
EINT
ECLK
ELIN
ELOUT
I/O 3-State
(Z)
Reset
State
I
O
O (Z)
I/O (Z)
O (Z)
I/O (Z)
I/O (Z)
I
I/O (Z)
I
I/O (Z)
I
I/O (Z)
I
I/O (Z)
I
O
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Hi-Z
I
Hi-Z
I
Hi-Z
I
Hi-Z
I
Hi-Z
I/O (Z)
I/O (Z)
O (Z)
O (Z)
O (Z)
O (Z)
O (Z)
O (Z)
O (Z)
I
O (Z)
O
I/O (Z)
I/O (Z)
I/O (Z)
I/O (Z)
I/O
I/O
I
I/O
O
I/O
I/O
I
I/O
O
I
I
O
I
O
I
I
I
O
Hi-Z
Hi-Z
O
O
O
O
O
O
O
I
O
O
I
I
I
I
I
I
I
I
O
I
I
I
I
O
I
I
O
I
O
I
I
I
O
Hi-Z*
Caused By
BR, EBR
IS
BR, EBR
BR, EBR
BR, EBR
BR, EBR
BR, EBR
BR, EBR
BR, EBR
BR, EBR
IS
BR, EBR
BR, EBR
BR, EBR
BR, EBR
BR, EBR
BR, EBR
BR, EBR
EE
Unused Configuration
Float
Float
Float
Float
Float
Float
Float
High (Inactive)
Float
High (Inactive)
Float
Low (Inactive)
Float
High (Inactive)
Float
Float
Float
Float
Float
Float
Float
Float
Float
Float
Float
High (Inactive)
Float
Float
Input = High (Inactive) or Program as Output, Set to 1, Let Float
Input = High (Inactive) or Program as Output, Set to 1, Let Float
Input = High (Inactive) or Program as Output, Set to 1, Let Float
Input = High (Inactive) or Program as Output, Set to 1, Let Float
Input = High or Low, Output = Float
High or Low
High or Low
High or Low
Float
Input = High or Low, Output = Float
High or Low
High or Low
High or Low
Float
Float
Float
Float
Float
Float
Float
Float
Float
Float
NOTES
*Hi-Z = High Impedance.
1. If the CLKOUT pin is not used, turn it OFF, using CLKODIS in SPORT0 autobuffer control register.
2. If the Interrupt/Programmable Flag pins are not used, there are two options: Option 1: When these pins are configured as INPUTS at reset and function as interrupts and input flag pins, pull the pins High (inactive). Option 2: Program the unused pins as OUTPUTS, set them to 1, prior to enabling interrupts, and let pins float.
3. All bidirectional pins have three-stated outputs. When the pin is configured as an output, the output is Hi-Z (high impedance) when inactive.
4. CLKIN, RESET, and PF3:0/MODE D:A are not included in the table because these pins must be used.
–8–
REV. 0
ADSP-2186M
Interrupts
The interrupt controller allows the processor to respond to the
11 possible interrupts and reset with minimum overhead. The
ADSP-2186M provides four dedicated external interrupt input
pins: IRQ2, IRQL0, IRQL1, and IRQE (shared with the PF7:4
pins). In addition, SPORT1 may be reconfigured for IRQ0,
IRQ1, FI and FO, for a total of six external interrupts. The
ADSP-2186M also supports internal interrupts from the timer,
the byte DMA port, the two serial ports, software, and the powerdown control circuit. The interrupt levels are internally prioritized
and individually maskable (except power- down and reset). The
IRQ2, IRQ0, and IRQ1 input pins can be programmed to be
either level- or edge-sensitive. IRQL0 and IRQL1 are levelsensitive and IRQE is edge-sensitive. The priorities and vector
addresses of all interrupts are shown in Table I.
Table I. Interrupt Priority and Interrupt Vector Addresses
of the state of IMASK. Disabling the interrupts does not affect
serial port autobuffering or DMA.
ENA INTS;
DIS INTS;
When the processor is reset, interrupt servicing is enabled.
LOW POWER OPERATION
The ADSP-2186M has three low power modes that significantly
reduce the power dissipation when the device operates under
standby conditions. These modes are:
• Power-Down
• Idle
• Slow Idle
The CLKOUT pin may also be disabled to reduce external
power dissipation.
Power-Down
Source Of Interrupt
Interrupt Vector
Address (Hex)
Reset (or Power-Up with PUCR = 1)
Power-Down (Nonmaskable)
IRQ2
IRQL1
IRQL0
SPORT0 Transmit
SPORT0 Receive
IRQE
BDMA Interrupt
SPORT1 Transmit or IRQ1
SPORT1 Receive or IRQ0
Timer
0000 (Highest Priority)
002C
0004
0008
000C
0010
0014
0018
001C
0020
0024
0028 (Lowest Priority)
Interrupt routines can either be nested with higher priority interrupts taking precedence or processed sequentially. Interrupts
can be masked or unmasked with the IMASK register. Individual
interrupt requests are logically ANDed with the bits in IMASK;
the highest priority unmasked interrupt is then selected. The
power-down interrupt is nonmaskable.
The ADSP-2186M masks all interrupts for one instruction
cycle following the execution of an instruction that modifies the
IMASK register. This does not affect serial port autobuffering
or DMA transfers.
The interrupt control register, ICNTL, controls interrupt nesting and defines the IRQ0, IRQ1, and IRQ2 external interrupts
to be either edge- or level-sensitive. The IRQE pin is an external edge sensitive interrupt and can be forced and cleared. The
IRQL0 and IRQL1 pins are external level sensitive interrupts.
The IFC register is a write-only register used to force and clear
interrupts. On-chip stacks preserve the processor status and are
automatically maintained during interrupt handling. The stacks
are twelve levels deep to allow interrupt, loop, and subroutine
nesting. The following instructions allow global enable or disable
servicing of the interrupts (including power down), regardless
REV. 0
The ADSP-2186M processor has a low power feature that lets
the processor enter a very low-power dormant state through
hardware or software control. Following is a brief list of powerdown features. Refer to the ADSP-2100 Family User’s Manual,
“System Interface” chapter, for detailed information about the
power-down feature.
• Quick recovery from power-down. The processor begins
executing instructions in as few as 200 CLKIN cycles.
• Support for an externally generated TTL or CMOS processor
clock. The external clock can continue running during powerdown without affecting the lowest power rating and 200 CLKIN
cycle recovery.
• Support for crystal operation includes disabling the oscillator
to save power (the processor automatically waits approximately
4096 CLKIN cycles for the crystal oscillator to start or stabilize), and letting the oscillator run to allow 200 CLKIN cycle
start-up.
• Power-down is initiated by either the power-down pin (PWD)
or the software power-down force bit. Interrupt support allows
an unlimited number of instructions to be executed before
optionally powering down. The power-down interrupt also
can be used as a nonmaskable, edge-sensitive interrupt.
• Context clear/save control allows the processor to continue
where it left off or start with a clean context when leaving the
power-down state.
• The RESET pin also can be used to terminate power-down.
• Power-down acknowledge pin indicates when the processor
has entered power-down.
Idle
When the ADSP-2186M is in the Idle Mode, the processor
waits indefinitely in a low-power state until an interrupt occurs.
When an unmasked interrupt occurs, it is serviced; execution
then continues with the instruction following the IDLE instruction. In Idle mode IDMA, BDMA and autobuffer cycle steals
still occur.
–9–
ADSP-2186M
The IDLE instruction is enhanced on the ADSP-2186M to let
the processor’s internal clock signal be slowed, further reducing
power consumption. The reduced clock frequency, a programmable fraction of the normal clock rate, is specified by a selectable
divisor given in the IDLE instruction.
ADSP-2186M also provides four external interrupts and two
serial ports or six external interrupts and one serial port. Host
Memory Mode allows access to the full external data bus, but
limits addressing to a single address bit (A0). Through the use
of external hardware, additional system peripherals can be added
in this mode to generate and latch address signals.
The format of the instruction is:
Clock Signals
IDLE (n);
The ADSP-2186M can be clocked by either a crystal or a
TTL-compatible clock signal.
Slow Idle
where n = 16, 32, 64, or 128. This instruction keeps the processor fully functional, but operating at the slower clock rate. While
it is in this state, the processor’s other internal clock signals, such
as SCLK, CLKOUT, and timer clock, are reduced by the same
ratio. The default form of the instruction, when no clock divisor
is given, is the standard IDLE instruction.
The CLKIN input cannot be halted, changed during operation, nor operated below the specified frequency during normal
operation. The only exception is while the processor is in the
power-down state. For additional information, refer to Chapter 9, ADSP-2100 Family User’s Manual, for detailed information
on this power-down feature.
When the IDLE (n) instruction is used, it effectively slows down
the processor’s internal clock and thus its response time to incoming interrupts. The one-cycle response time of the standard idle
state is increased by n, the clock divisor. When an enabled interrupt is received, the ADSP-2186M will remain in the idle state
for up to a maximum of n processor cycles (n = 16, 32, 64, or
128) before resuming normal operation.
If an external clock is used, it should be a TTL-compatible signal
running at half the instruction rate. The signal is connected to
the processor’s CLKIN input. When an external clock is used,
the XTAL input must be left unconnected.
The ADSP-2186M uses an input clock with a frequency equal to
half the instruction rate; a 37.50 MHz input clock yields a 13 ns
processor cycle (which is equivalent to 75 MHz). Normally,
instructions are executed in a single processor cycle. All device
timing is relative to the internal instruction clock rate, which is
indicated by the CLKOUT signal when enabled.
When the IDLE (n) instruction is used in systems that have an
externally generated serial clock (SCLK), the serial clock rate
may be faster than the processor’s reduced internal clock rate.
Under these conditions, interrupts must not be generated at a
faster than can be serviced, due to the additional time the
processor takes to come out of the idle state (a maximum of n
processor cycles).
Because the ADSP-2186M includes an on-chip oscillator circuit,
an external crystal may be used. The crystal should be connected
across the CLKIN and XTAL pins, with two capacitors connected as shown in Figure 3. Capacitor values are dependent on
crystal type and should be specified by the crystal manufacturer.
A parallel-resonant, fundamental frequency, microprocessorgrade crystal should be used.
SYSTEM INTERFACE
Figure 2 shows typical basic system configurations with the
ADSP-2186M, two serial devices, a byte-wide EPROM, and
optional external program and data overlay memories (modeselectable). Programmable wait state generation allows the
processor to connect easily to slow peripheral devices. The
A clock output (CLKOUT) signal is generated by the processor
at the processor’s cycle rate. This can be enabled and disabled by
the CLKODIS bit in the SPORT0 Autobuffer Control Register.
HOST MEMORY MODE
FULL MEMORY MODE
ADSP-2186M
ADSP-2186M
1/2x CLOCK
OR
CRYSTAL
CLKIN
XTAL
14
SERIAL
DEVICE
SERIAL
DEVICE
D23–16
IRQ2/PF7
IRQE/PF4 DATA23–0
IRQL0/PF5
BMS
IRQL1/PF6
WR
MODE D/PF3
RD
MODE C/PF2
MODE A/PF0
MODE B/PF1
IOMS
SPORT1
SCLK1
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
PMS
DR1 OR FI
DMS
CMS
SPORT0
SCLK0
RFS0
TFS0
DT0
DR0
A13–0
ADDR13–0
FL0–2
BR
BG
BGH
PWD
PWDACK
24
D15–8
CLKIN
1/2x CLOCK
OR
CRYSTAL
XTAL
A0–A21
DATA
FL0–2
BYTE
MEMORY
IRQ2/PF7
IRQE/PF4 DATA23–8
IRQL0/PF5
IRQL1/PF6
BMS
MODE D/PF3
WR
MODE C/PF2
RD
MODE A/PF0
MODE B/PF1
CS
A10–0
D23–8
ADDR
I/O SPACE
DATA (PERIPHERALS)
2048 LOCATIONS
SPORT1
CS
SERIAL
DEVICE
SCLK1
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
DR1 OR FI
SERIAL
DEVICE
SPORT0
SCLK0
RFS0
TFS0
DT0
DR0
A13–0
ADDR
D23–0
DATA
1
A0
OVERLAY
MEMORY
TWO 8K
PM SEGMENTS
TWO 8K
DM SEGMENTS
16
IOMS
PMS
DMS
CMS
BR
BG
BGH
PWD
IDMA PORT
PWDACK
IRD/D6
IWR/D7
IS/D4
IAL/D5
IACK/D3
IAD15–0
SYSTEM
INTERFACE
OR
␮CONTROLLER
16
Figure 2. Basic System Interface
–10–
REV. 0
ADSP-2186M
performed. The first instruction is fetched from on-chip program memory location 0x0000 once boot loading completes.
CLKIN
XTAL
Power Supplies
CLKOUT
DSP
Figure 3. External Crystal Connections
RESET
The RESET signal initiates a master reset of the ADSP-2186M.
The RESET signal must be asserted during the power-up
sequence to assure proper initialization. RESET during initial
power-up must be held long enough to allow the internal clock
to stabilize. If RESET is activated any time after power-up, the
clock continues to run and does not require stabilization time.
The power-up sequence is defined as the total time required for the
crystal oscillator circuit to stabilize after a valid VDD is applied to
the processor, and for the internal phase-locked loop (PLL) to lock
onto the specific crystal frequency. A minimum of 2000 CLKIN
cycles ensures that the PLL has locked but does not include the
crystal oscillator start-up time. During this power-up sequence
the RESET signal should be held low. On any subsequent resets,
the RESET signal must meet the minimum pulsewidth specification, tRSP.
The RESET input contains some hysteresis; however, if an
RC circuit is used to generate the RESET signal, the use of an
external Schmidt trigger is recommended.
The master reset sets all internal stack pointers to the empty stack
condition, masks all interrupts, and clears the MSTAT register.
When RESET is released, if there is no pending bus request and
the chip is configured for booting, the boot-loading sequence is
The ADSP-2186M has separate power supply connections for
the internal (VDDINT) and external (VDDEXT) power supplies.
The internal supply must meet the 2.5 V requirement. The
external supply can be connected to either a 2.5 V or 3.3 V supply.
All external supply pins must be connected to the same supply.
All input and I/O pins can tolerate input voltages up to 3.6 V,
regardless of the external supply voltage. This feature provides
maximum flexibility in mixing 2.5 V and 3.3 V components.
MODES OF OPERATION
Setting Memory Mode
Memory Mode selection for the ADSP-2186M is made during
chip reset through the use of the Mode C pin. This pin is multiplexed with the DSP’s PF2 pin, so care must be taken in how
the mode selection is made. The two methods for selecting the
value of Mode C are active and passive.
Passive Configuration
Passive Configuration involves the use a pull-up or pull-down
resistor connected to the Mode C pin. To minimize power consumption, or if the PF2 pin is to be used as an output in the DSP
application, a weak pull-up or pull-down, on the order of 10 kΩ,
can be used. This value should be sufficient to pull the pin to the
desired level and still allow the pin to operate as a programmable
flag output without undue strain on the processor’s output driver.
For minimum power consumption during power-down, reconfigure PF2 to be an input, as the pull-up or pull-down will
hold the pin in a known state, and will not switch.
Table II. Modes of Operation
MODE D
MODE C
MODE B
MODE A
Booting Method
X
0
0
0
BDMA feature is used to load the first 32 program memory words from
the byte memory space. Program execution is held off until all 32 words
have been loaded. Chip is configured in Full Memory Mode.1
X
0
1
0
No automatic boot operations occur. Program execution starts at external
memory location 0. Chip is configured in Full Memory Mode. BDMA can
still be used, but the processor does not automatically use or wait for these
operations.
0
1
0
0
BDMA feature is used to load the first 32 program memory words from
the byte memory space. Program execution is held off until all 32 words
have been loaded. Chip is configured in Host Mode. IACK has active
pull-down. (REQUIRES ADDITIONAL HARDWARE).
0
1
0
1
IDMA feature is used to load any internal memory as desired. Program
execution is held off until internal program memory location 0 is written
to. Chip is configured in Host Mode. IACK has active pull-down.1
1
1
0
0
BDMA feature is used to load the first 32 program memory words from
the byte memory space. Program execution is held off until all 32 words
have been loaded. Chip is configured in Host Mode; IACK requires external pull down. (REQUIRES ADDITIONAL HARDWARE)
1
1
0
1
IDMA feature is used to load any internal memory as desired. Program
execution is held off until internal program memory location 0 is written
to. Chip is configured in Host Mode. IACK requires external pull-down.1
NOTE
1
Considered as standard operating settings. Using these configurations allows for easier design and better memory management.
REV. 0
–11–
ADSP-2186M
Active Configuration
MEMORY ARCHITECTURE
Active Configuration involves the use of a three-statable external
driver connected to the Mode C pin. A driver’s output enable
should be connected to the DSP’s RESET signal such that it
only drives the PF2 pin when RESET is active (low). When
RESET is deasserted, the driver should three-state, thus allowing full use of the PF2 pin as either an input or output. To
minimize power consumption during power-down, configure
the programmable flag as an output when connected to a threestated buffer. This ensures that the pin will be held at a constant
level, and will not oscillate should the three-state driver’s level
hover around the logic switching point.
The ADSP-2186M provides a variety of memory and peripheral
interface options. The key functional groups are Program Memory,
Data Memory, Byte Memory, and I/O. Refer to the following
figures and tables for PM and DM memory allocations in the
ADSP-2186M.
IACK Configuration
Mode D = 0 and in host mode: IACK is an active, driven signal
and cannot be “wire OR’d.”
Mode D = 1 and in host mode: IACK is an open drain and
requires an external pull-down, but multiple IACK pins can be
“wire OR’d” together.
Program Memory
Program Memory (Full Memory Mode) is a 24-bit-wide
space for storing both instruction opcodes and data. The ADSP2186M has 8K words of Program Memory RAM on chip, and
the capability of accessing up to two 8K external memory overlay spaces using the external data bus.
Program Memory (Host Mode) allows access to all internal
memory. External overlay access is limited by a single external
address line (A0). External program execution is not available in
host mode due to a restricted data bus that is 16 bits wide only.
PM (MODE B = 1)1
PM (MODE B = 0)
ALWAYS
ACCESSIBLE
AT ADDRESS
0x0000 – 0x1FFF
RESERVED
0x2000 –
0x3FFF
0x2000 –
0x3FFF
0x0000 –
0x1FFF2
RESERVED
PMOVLAY = 0
RESERVED
ACCESSIBLE WHEN
PMOVLAY = 0
ACCESSIBLE WHEN
PMOVLAY = 1
0x0000 –
0x1FFF2
0x2000 –
0x3FFF2
EXTERNAL
MEMORY
RESERVED
0x2000 –
0x3FFF2
EXTERNAL
MEMORY
NOTES:
1WHEN MODE B = 1, PMOVLAY MUST BE SET TO 0
2SEE TABLE III FOR PMOVLAY BITS
ACCESSIBLE WHEN
PMOVLAY = 2
PROGRAM MEMORY
MODE B = 0
ADDRESS
PROGRAM MEMORY
MODE B = 1
ADDRESS
0x3FFF
0x3FFF
8K EXTERNAL
PMOVLAY = 1, 2
RESERVED
0x2000
0x2000
0x1FFF
0x1FFF
8K
INTERNAL
8K EXTERNAL
PMOVLAY = 0
0x0000
0x0000
Figure 4. Program Memory
Table III. PMOVLAY Bits
PMOVLAY
Memory
A13
A12:0
0
1
2
Reserved
External Overlay 1
External Overlay 2
Not Applicable
0
1
Not Applicable
13 LSBs of Address Between 0x2000 and 0x3FFF
13 LSBs of Address Between 0x2000 and 0x3FFF
–12–
REV. 0
ADSP-2186M
Data Memory
Data Memory (Full Memory Mode) is a 16-bit-wide space used
for the storage of data variables and for memory-mapped control
registers. The ADSP-2186M has 8K words on Data Memory
RAM on-chip. Part of this space is used by 32 memory-mapped
registers. Support also exists for up to two 8K external memory
overlay spaces through the external data bus. All internal accesses
complete in one cycle. Accesses to external memory are timed
using the wait states specified by the DWAIT register and the
wait state mode bit.
Data Memory (Host Mode) allows access to all internal
memory. External overlay access is limited by a single external
address line (A0).
DATA MEMORY
ALWAYS
ACCESSIBLE
AT ADDRESS
0x2000 – 0x3FFF
DATA MEMORY
ADDR
32 MEMORY
MAPPED
REGISTERS
0x3FFF
0x3FE0
0x3FDF
INTERNAL
8160 WORDS
0x2000
0x0000 – 0x1FFF
0x1FFF
DM OVLAY = 0
RESERVED
EXTERNAL 8K
DMOVLAY = 1, 2
0x0000 – 0x1FFF1
0x0000 – 0x1FFF1
0x0000
ACCESSIBLE WHEN
DMOVLAY = 1
EXTERNAL
MEMORY
NOTE:
1SEE TABLE IV FOR DMOVLAY BITS
ACCESSIBLE WHEN
DMOVLAY = 2
Figure 5. Data Memory Map
Table IV. DMOVLAY Bits
DMOVLAY
Memory
A13
A12:0
0
1
2
Reserved
External Overlay 1
External Overlay 2
Not Applicable
0
1
Not Applicable
13 LSBs of Address Between 0x2000 and 0x3FFF
13 LSBs of Address Between 0x2000 and 0x3FFF
SYSTEM CONTROL
Memory Mapped Registers (New to the ADSP-2186M)
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
The ADSP-2186M has three memory mapped registers that differ
from other ADSP-21xx Family DSPs. The slight modifications
to these registers (Wait State Control, Programmable Flag and
Composite Select Control, and System Control) provide the
ADSP-2186M’s wait state and BMS control features. Default
bit values at reset are shown; if no value is shown, the bit is undefined at reset. Reserved bits are shown on a grey field. These bits
should always be written with zeros.
0
0
0
0
0
0
0
0
1
1
1
9
8
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DWAIT
1
IOWAIT3
IOWAIT2
IOWAIT1
9
8
7
6
5
4
3
2
1
0
1
1
0
0
0
0
0
0
0
0
BMWAIT
1
1
0
CMSSEL
0 = DISABLE CMS
1 = ENABLE CMS
DM(0x3FE6)
PFTYPE
0 = INPUT
1 = OUTPUT
(WHERE BIT: 11-IOM, 10-BM, 9-DM, 8-PM)
Figure 7. Programmable Flag and Composite Control
Register
REV. 0
RESERVED, ALWAYS
SET TO 0
DM(0x3FFF)
PWAIT
PROGRAM MEMORY
WAIT STATES
DISABLE BMS
0 = ENABLE BMS
1 = DISABLE BMS, EXCEPT WHEN MEMORY
STROBES ARE THREE-STATED
NOTE: RESERVED BITS ARE SHOWN ON A GRAY FIELD. THESE BITS SHOULD
ALWAYS BE WRITTEN WITH ZEROS.
Figure 8. System Control Register
PROGRAMMABLE FLAG AND COMPOSITE SELECT CONTROL
1
1
SPORT1 ENABLE
0 = DISABLE
1 = ENABLE
DM(0x3FFE)
Figure 6. Wait State Control Register
1
0
SPORT1 CONFIGURE
0 = FI, FO, IRQ0, IRQ1, SCLK
1 = SPORT1
WAIT STATE MODE SELECT
0 = NORMAL MODE (PWAIT, DWAIT, IOWAIT0–3 = N WAIT STATES, RANGING
FROM 0 TO 7)
1 = 2N + 1 MODE (PWAIT, DWAIT, IOWAIT0–3 = 2N + 1 WAIT STATES, RANGING
FROM 0 TO 15)
1
0
SPORT0 ENABLE
0 = DISABLE
1 = ENABLE
IOWAIT0
15 14 13 12 11 10
0
RESERVED
SET TO 0
WAITSTATE CONTROL
15 14 13 12 11 10
0
I/O Space (Full Memory Mode)
The ADSP-2186M supports an additional external memory
space called I/O space. This space is designed to support simple
connections to peripherals (such as data converters and external
registers) or to bus interface ASIC data registers. I/O space supports 2048 locations of 16-bit wide data. The lower eleven bits
of the external address bus are used; the upper three bits are
undefined. Two instructions were added to the core ADSP-2100
Family instruction set to read from and write to I/O memory
space. The I/O space also has four dedicated three-bit wait state
registers, IOWAIT0–3, which in combination with the wait state
mode bit, specify up to 15 wait states to be automatically generated for each of four regions. The wait states act on address
ranges as shown in Table V.
–13–
ADSP-2186M
Table V. Wait States
15 14 13 12 11 10
Address Range
Wait State Register
0x000–0x1FF
0x200–0x3FF
0x400–0x5FF
0x600–0x7FF
IOWAIT0 and Wait State Mode Select Bit
IOWAIT1 and Wait State Mode Select Bit
IOWAIT2 and Wait State Mode Select Bit
IOWAIT3 and Wait State Mode Select Bit
0
0
0
0
0
0
BDMA CONTROL
9 8 7 6 5
0
0
BMPAGE
0
0
0
4
3
2
1
0
0
1
0
0
0
BTYPE
BDIR
0 = LOAD FROM BM
1 = STORE TO BM
BCR
0 = RUN DURING BDMA
1 = HALT DURING BDMA
BDMA
OVERLAY
BITS*
*THESE BITS SHOULD ALWAYS
BE WRITTEN WITH ZEROS.
Composite Memory Select (CMS)
The ADSP-2186M has a programmable memory select signal that
is useful for generating memory select signals for memories
mapped to more than one space. The CMS signal is generated to have the same timing as each of the individual memory
select signals (PMS, DMS, BMS, IOMS) but can combine their
functionality.
Each bit in the CMSSEL register, when set, causes the CMS
signal to be asserted when the selected memory select is
asserted. For example, to use a 32K word memory to act as both
program and data memory, set the PMS and DMS bits in the
CMSSEL register and use the CMS pin to drive the chip
select of the memory, and use either DMS or PMS as the
additional address bit.
DM (0x3FE3)
Figure 9. BDMA Control Register
The BDMA circuit supports four different data formats that are
selected by the BTYPE register field. The appropriate number
of 8-bit accesses are done from the byte memory space to build
the word size selected. Table VI shows the data formats supported by the BDMA circuit.
Table VI. Data Formats
The CMS pin functions like the other memory select signals
with the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the CMS signal at the same time as the
selected memory select signal. All enable bits default to 1 at reset,
except the BMS bit.
Byte Memory Select (BMS)
The ADSP-2186M’s BMS disable feature combined with the
CMS pin allows use of multiple memories in the byte memory
space. For example, an EPROM could be attached to the BMS
select, and an SRAM could be connected to CMS. Because at
reset BMS is enabled, the EPROM would be used for booting.
After booting, software could disable BMS and set the CMS
signal to respond to BMS, enabling the SRAM.
BTYPE
Internal Memory Space Word Size Alignment
00
01
10
11
Program Memory
Data Memory
Data Memory
Data Memory
24
16
8
8
Full Word
Full Word
MSBs
LSBs
Unused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address
for the on-chip memory involved with the transfer. The 14-bit
BEAD register specifies the starting address for the external byte
memory space. The 8-bit BMPAGE register specifies the starting page for the external byte memory space. The BDIR register
field selects the direction of the transfer. Finally, the 14-bit
BWCOUNT register specifies the number of DSP words to
transfer and initiates the BDMA circuit transfers.
BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT register.
Byte Memory
The byte memory space is a bidirectional, 8-bit-wide, external
memory space used to store programs and data. Byte memory is
accessed using the BDMA feature. The byte memory space consists of 256 pages, each of which is 16K × 8.
The byte memory space on the ADSP-2186M supports read and
write operations as well as four different data formats. The byte
memory uses data bits 15:8 for data. The byte memory uses data
bits 23:16 and address bits 13:0 to create a 22-bit address. This
allows up to a 4 meg × 8 (32 megabit) ROM or RAM to be used
without glue logic. All byte memory accesses are timed by the
BMWAIT register and the wait state mode bit.
Byte Memory DMA (BDMA, Full Memory Mode)
The byte memory DMA controller allows loading and storing of
program instructions and data using the byte memory space. The
BDMA circuit is able to access the byte memory space while the
processor is operating normally and steals only one DSP cycle
per 8-, 16- or 24-bit word transferred.
The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches zero,
the transfers have finished and a BDMA interrupt is generated.
The BMPAGE and BEAD registers must not be accessed by the
DSP during BDMA operations.
The source or destination of a BDMA transfer will always be
on-chip program or data memory.
When the BWCOUNT register is written with a nonzero value
the BDMA circuit starts executing byte memory accesses with wait
states set by BMWAIT. These accesses continue until the count
reaches zero. When enough accesses have occurred to create a
destination word, it is transferred to or from on-chip memory.
The transfer takes one DSP cycle. DSP accesses to external
memory have priority over BDMA byte memory accesses.
The BDMA Context Reset bit (BCR) controls whether the
processor is held off while the BDMA accesses are occurring.
Setting the BCR bit to 0 allows the processor to continue operations. Setting the BCR bit to 1 causes the processor to stop
execution while the BDMA accesses are occurring, to clear the
context of the processor, and start execution at address 0 when
the BDMA accesses have completed.
–14–
REV. 0
ADSP-2186M
Through the IDMAA register, the DSP can also specify the
starting address and data format for DMA operation. Asserting
the IDMA port select (IS) and address latch enable (IAL) directs
the ADSP-2186M to write the address onto the IAD0–14 bus
into the IDMA Control Register. If Bit 15 is set to 0, IDMA
latches the address. If Bit 15 is set to 1, IDMA latches into the
OVLAY register. This register, shown below, is memory mapped
at address DM (0x3FE0). Note that the latched address (IDMAA)
cannot be read back by the host. When Bit 14 in 0x3FE7 is set
to 1, timing in Figure 31 applies for short reads. When Bit 14
in 0x3FE7 is set to zero, short reads use the timing shown in Figure 32. For ADSP-2186M, IDDMOVLAY and IDPMOVLAY
bits in IDMA overlay register should be set to zero.
The BDMA overlay bits specify the OVLAY memory blocks to
be accessed for internal memory. For ADSP-2186M, set to zero
BDMA overlay bits in BDMA control register.
The BMWAIT field, which has four bits on ADSP-2186M,
allows selection of up to 15 wait states for BDMA transfers.
Internal Memory DMA Port (IDMA Port; Host Memory
Mode)
The IDMA Port provides an efficient means of communication
between a host system and the ADSP-2186M. The port is used
to access the on-chip program memory and data memory of the
DSP with only one DSP cycle per word overhead. The IDMA
port cannot, however, be used to write to the DSP’s memorymapped control registers. A typical IDMA transfer process is
described as follows:
Refer to the following figures for more information on IDMA
and DMA memory maps.
1. Host starts IDMA transfer.
2. Host checks IACK control line to see if the DSP is busy.
IDMA OVERLAY
15 14 13 12 11 10
3. Host uses IS and IAL control lines to latch either the DMA
starting address (IDMAA) or the PM/DM OVLAY selection
into the DSP’s IDMA control registers. If Bit 15 = 1, the
value of bits 7:0 represent the IDMA overlay: bits 14:8 must
be set to 0. If Bit 15 = 0, the value of Bits 13:0 represent the
starting address of internal memory to be accessed and
Bit 14 reflects PM or DM for access. For ADSP-2186M,
IDDMOVLAY and IDPMOVLAY bits in IDMA overlay
register should be set to zero.
0
0
0
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
DM (0x3FE7)
IDPMOVLAY2
SHORT READ ONLY
0 = ENABLE
1 = DISABLE
IDMA CONTROL (U = UNDEFINED AT RESET)
15 14 13 12 11 10
0
U
U
U
U
U
9
8
7
6
5
4
3
2
1
0
U
U
U
U
U
U
U
U
U
U
DM (0x3FE0)
IDMAA ADDRESS
RESERVED SET TO 0
IDMAD DESTINATION MEMORY TYPE
0 = PM
1 = DM
NOTES:
1RESERVED BITS ARE SHOWN ON A GRAY FIELD.
2THESE BITS SHOULD ALWAYS BE WRITTEN WITH ZEROS.
6. Host ends IDMA transfer.
Figure 10. IDMA Control/OVLAY Registers
The IDMA port has a 16-bit multiplexed address and data bus
and supports 24-bit program memory. The IDMA port is completely asynchronous and can be written while the ADSP-2186M
is operating at full speed.
DMA
PROGRAM MEMORY
DMA
DATA MEMORY
ALWAYS
ACCESSIBLE
AT ADDRESS
0x0000 – 0x1FFF
The DSP memory address is latched and then automatically incremented after each IDMA transaction. An external device can
therefore access a block of sequentially addressed memory by
specifying only the starting address of the block. This increases
throughput as the address does not have to be sent for each
memory access.
ALWAYS
ACCESSIBLE
AT ADDRESS
0x2000 – 0x3FFF
0x2000 –
0x3FFF
RESERVED
IDMA Port access occurs in two phases. The first is the IDMA
Address Latch cycle. When the acknowledge is asserted, a 14-bit
address and 1-bit destination type can be driven onto the bus by
an external device. The address specifies an on-chip memory
location, the destination type specifies whether it is a DM or
PM access. The falling edge of the IDMA address latch signal
(IAL) or the missing edge of the IDMA select signal (IS) latches
this value into the IDMAA register.
REV. 0
0
RESERVED SET TO 0
5. Host checks IACK line to see if the DSP has completed the
previous IDMA operation.
Once an access has occurred, the latched address is automatically incremented, and another access can occur.
0
RESERVED SET TO 01,2 IDDMOVLAY2
4. Host uses IS and IRD (or IWR) to read (or write) DSP internal memory (PM or DM).
Once the address is stored, data can be read from, or written to,
the ADSP-2186M’s on-chip memory. Asserting the select line
(IS) and the appropriate read or write line (IRD and IWR
respectively) signals the ADSP-2186M that a particular transaction is required. In either case, there is a one-processor-cycle
delay for synchronization. The memory access consumes one
additional processor cycle.
0
0x0000 –
0x1FFF
RESERVED
NOTE: IDMA AND BDMA HAVE SEPARATE DMA CONTROL REGISTERS.
Figure 11. Direct Memory Access—PM and DM
Memory Maps
Bootstrap Loading (Booting)
The ADSP-2186M has two mechanisms to allow automatic loading of the internal program memory after reset. The method for
booting is controlled by the Mode A, B, and C configuration bits.
When the MODE pins specify BDMA booting, the ADSP-2186M
initiates a BDMA boot sequence when reset is released.
The BDMA interface is set up during reset to the following
defaults when BDMA booting is specified: the BDIR, BMPAGE,
BIAD, and BEAD registers are set to 0, the BTYPE register is
set to 0 to specify program memory 24-bit words, and the
BWCOUNT register is set to 32. This causes 32 words of
on-chip program memory to be loaded from byte memory.
–15–
ADSP-2186M
These 32 words are used to set up the BDMA to load in the
remaining program code. The BCR bit is also set to 1, which
causes program execution to be held off until all 32 words are
loaded into on-chip program memory. Execution then begins at
address 0.
read and write the values on the pins. Data being read from a
pin configured as an input is synchronized to the ADSP-2186M’s
clock. Bits that are programmed as outputs will read the value
being output. The PF pins default to input during reset.
In addition to the programmable flags, the ADSP-2186M has five
fixed-mode flags, FI, FO, FL0, FL1, and FL2. FL0–FL2 are
dedicated output flags. FI and FO are available as an alternate
configuration of SPORT1.
The ADSP-2100 Family development software (Revision 5.02
and later) fully supports the BDMA booting feature and can
generate byte-memory space-compatible boot code.
The IDLE instruction can also be used to allow the processor
to hold off execution while booting continues through the
BDMA interface. For BDMA accesses while in Host Mode, the
addresses to boot memory must be constructed externally to the
ADSP-2186M. The only memory address bit provided by the
processor is A0.
IDMA Port Booting
The ADSP-2186M can also boot programs through its Internal
DMA port. If Mode C = 1, Mode B = 0, and Mode A = 1, the
ADSP-2186M boots from the IDMA port. IDMA feature can
load as much on-chip memory as desired. Program execution is
held off until on-chip program memory location 0 is written to.
Note: Pins PF0, PF1, PF2, and PF3 are also used for device
configuration during reset.
Instruction Set Description
The ADSP-2186M assembly language instruction set has an
algebraic syntax that was designed for ease of coding and readability. The assembly language, which takes full advantage of the
processor’s unique architecture, offers the following benefits:
• The algebraic syntax eliminates the need to remember cryptic
assembler mnemonics. For example, a typical arithmetic add
instruction, such as AR = AX0 + AY0, resembles a simple
equation.
Bus Request and Bus Grant
The ADSP-2186M can relinquish control of the data and address
buses to an external device. When the external device requires
access to memory, it asserts the bus request (BR) signal. If the
ADSP-2186M is not performing an external memory access, it
responds to the active BR input in the following processor cycle by:
• Three-stating the data and address buses and the PMS, DMS,
BMS, CMS, IOMS, RD, WR output drivers,
• Every instruction assembles into a single, 24-bit word that
can execute in a single instruction cycle.
• The syntax is a superset ADSP-2100 Family assembly language and is completely source and object code compatible
with other family members. Programs may need to be relocated
to utilize on-chip memory and conform to the ADSP-2186M’s
interrupt vector and reset vector map.
• Halting program execution.
• Sixteen condition codes are available. For conditional jump,
call, return, or arithmetic instructions, the condition can
be checked and the operation executed in the same instruction cycle.
If Go Mode is enabled, the ADSP-2186M will not halt program
execution until it encounters an instruction that requires an
external memory access.
• Multifunction instructions allow parallel execution of an
arithmetic instruction with up to two fetches or one write to
processor memory space during a single instruction cycle.
• Asserting the bus grant (BG) signal, and
If the ADSP-2186M is performing an external memory access
when the external device asserts the BR signal, it will not threestate the memory interfaces nor assert the BG signal until the
processor cycle after the access completes. The instruction does
not need to be completed when the bus is granted. If a single
instruction requires two external memory accesses, the bus will
be granted between the two accesses.
DESIGNING AN EZ-ICE-COMPATIBLE SYSTEM
The ADSP-2186M has on-chip emulation support and an
ICE-Port, a special set of pins that interface to the EZ-ICE.
These features allow in-circuit emulation without replacing the
target system processor by using only a 14-pin connection from
the target system to the EZ-ICE. Target systems must have a
14-pin connector to accept the EZ-ICE’s in-circuit probe, a
14-pin plug.
When the BR signal is released, the processor releases the BG
signal, re-enables the output drivers, and continues program
execution from the point at which it stopped.
The bus request feature operates at all times, including when
the processor is booting and when RESET is active.
The BGH pin is asserted when the ADSP-2186M requires the
external bus for a memory or BDMA access, but is stopped.
The other device can release the bus by deasserting bus request.
Once the bus is released, the ADSP-2186M deasserts BG and
BGH and executes the external memory access.
Flag I/O Pins
The ADSP-2186M has eight general purpose programmable
input/output flag pins. They are controlled by two memory
mapped registers. The PFTYPE register determines the direction, 1 = output and 0 = input. The PFDATA register is used to
Issuing the chip reset command during emulation causes the
DSP to perform a full chip reset, including a reset of its memory
mode. Therefore, it is vital that the mode pins are set correctly
PRIOR to issuing a chip reset command from the emulator user
interface. If a passive method of maintaining mode information is
being used (as discussed in Setting Memory Modes), it does not
matter that the mode information is latched by an emulator
reset. However, if the RESET pin is being used as a method of
setting the value of the mode pins, the effects of an emulator
reset must be taken into consideration.
One method of ensuring that the values located on the mode
pins are those desired is to construct a circuit like the one shown
in Figure 12. This circuit forces the value located on the Mode
A pin to logic high; regardless of whether it is latched via the
RESET or ERESET pin.
–16–
REV. 0
ADSP-2186M
ERESET
RESET
ADSP-2186M
1k⍀
MODE A/PFO
PROGRAMMABLE I/O
Figure 12. Mode A Pin/EZ-ICE Circuit
The 14-pin, 2-row pin strip header is keyed at the Pin 7 location—Pin 7 must be removed from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spacing should be 0.1 × 0.1 inches. The pin strip header must have
at least 0.15 inch clearance on all sides to accept the EZ- ICE
probe plug.
Pin strip headers are available from vendors such as 3M,
McKenzie, and Samtec.
Target Memory Interface
See the ADSP-2100 Family EZ-Tools data sheet for complete
information on ICE products.
For your target system to be compatible with the EZ-ICE
emulator, it must comply with the memory interface guidelines
listed below.
The ICE-Port interface consists of the following ADSP-2186M
pins: EBR, EINT, EE, EBG, ECLK, ERESET, ELIN, EMS,
and ELOUT
PM, DM, BM, IOM, AND CM
These ADSP-2186M pins must be connected only to the EZ-ICE
connector in the target system. These pins have no function except
during emulation, and do not require pull-up or pull-down
resistors. The traces for these signals between the ADSP-2186M
and the connector must be kept as short as possible, no longer
than 3 inches.
The following pins are also used by the EZ-ICE: BR, BG,
RESET, and GND.
The EZ-ICE uses the EE (emulator enable) signal to take control of the ADSP-2186M in the target system. This causes the
processor to use its ERESET, EBR, and EBG pins instead of
the RESET, BR, and BG pins. The BG output is three-stated.
These signals do not need to be jumper-isolated in your system.
The EZ-ICE connects to your target system via a ribbon cable
and a 14-pin female plug. The female plug is plugged onto the
14-pin connector (a pin strip header) on the target board.
Target Board Connector for EZ-ICE Probe
The EZ-ICE connector (a standard pin strip header) is shown in
Figure 13. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow enough
room in your system to fit the EZ-ICE probe onto the 14-pin
connector.
1
2
3
4
5
6
7
8
9
10
11
12
BG
GND
BR
EBG
EBR
KEY (NO PIN)
EINT
ⴛ
ELIN
ELOUT
ECLK
EMS
EE
13
14
RESET
ERESET
TOP VIEW
Figure 13. Target Board Connector for EZ-ICE
REV. 0
Design your Program Memory (PM), Data Memory (DM), Byte
Memory (BM), I/O Memory (IOM), and Composite Memory
(CM) external interfaces to comply with worst case device timing requirements and switching characteristics as specified in
this data sheet. The performance of the EZ- ICE may approach
published worst-case specification for some memory access
timing requirements and switching characteristics.
Note: If your target does not meet the worst-case chip specification for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. Depending on the severity of the specification violation, you may have
trouble manufacturing your system as DSP components statistically vary in switching characteristic and timing requirements
within published limits.
Restriction: All memory strobe signals on the ADSP-2186M
(RD, WR, PMS, DMS, BMS, CMS, and IOMS) used in your
target system must have 10 kΩ pull-up resistors connected when
the EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE debugging sessions. These resistors may be removed at
your option when the EZ-ICE is not being used.
Target System Interface Signals
When the EZ-ICE board is installed, the performance on some
system signals change. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE board:
• EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the RESET
signal.
• EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the BR signal.
• EZ-ICE emulation ignores RESET and BR when singlestepping.
• EZ-ICE emulation ignores RESET and BR when in Emulator
Space (DSP halted).
• EZ-ICE emulation ignores the state of target BR in certain
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (BG) is asserted
by the EZ- ICE board’s DSP.
–17–
ADSP-2186M–SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
K Grade
B Grade
Parameter
Min
Max
Min
Max
Unit
VDDINT
VDDEXT
VINPUT1
TAMB
2.37
2.37
VIL = –0.3
0
2.63
3.6
VIH = +3.6
+70
2.25
2.25
VIL = –0.3
–40
2.75
3.6
VIH = +3.6
+85
V
V
V
°C
NOTES
1
The ADSP-2186M is 3.3 V tolerant (always accepts up to 3.6 V max V IH), but voltage compliance (on outputs, V OH) depends on the input VDDEXT; because VOH (max)
≈ VDDEXT (max). This applies to bidirectional pins (D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS 0, TFS1, A1–A13, PF0–PF7) and input only pins (CLKIN, RESET,
BR, DR0, DR1, PWD).
Specifications subject to change without notice.
ELECTRICAL CHARACTERISTICS
Parameter
VIH
VIH
VIL
VOH
Hi-Level Input Voltage1, 2
Hi-Level CLKIN Voltage
Lo-Level Input Voltage1, 3
Hi-Level Output Voltage1, 4, 5
VOL
IIH
IIL
IOZH
IOZL
IDD
IDD
IDD
IDD
IDD
Lo-Level Output Voltage1, 4, 5
Hi-Level Input Current3
Lo-Level Input Current3
Three-State Leakage Current7
Three-State Leakage Current7
Supply Current (Idle)9
Supply Current (Idle)9
Supply Current (Dynamic)10
Supply Current (Dynamic)10
Supply Current (Power-Down)12
CI
CO
Input Pin Capacitance3, 6
Output Pin Capacitance6, 7, 12, 13
Test Conditions
Min
@ VDDINT = max
@ VDDINT = max
@ VDDINT = min
@ VDDEXT = min, IOH = –0.5 mA
@ VDDEXT = 3.0 V, IOH = –0.5 mA
@ VDDEXT = min, IOH = –100 µA6
@ VDDEXT = min, IOL = 2 mA
@ VDDINT = max, VIN = 3.6 V
@ VDDINT = max, VIN = 0 V
@ VDDEXT = max, VIN = 3.6 V8
@ VDDEXT = max, VIN = 0 V8
@ VDDINT = 2.5, tCK = 15 ns
@ VDDINT = 2.5, tCK = 13.3 ns
@ VDDINT = 2.5, tCK = 15 ns11, TAMB = 25°C
@ VDDINT = 2.5, tCK = 13.3 ns11, TAMB = 25°C
@ VDDINT = 2.5, TAMB = 25°C in Lowest
Power Mode
@ VIN = 2.5 V, fIN = 1.0 MHz, TAMB = 25°C
@ VIN = 2.5 V, fIN = 1.0 MHz, TAMB = 25°C
1.5
2.0
K/B Grades
Typ
Max
Unit
0.4
10
10
10
10
V
V
V
V
V
V
V
µA
µA
µA
µA
mA
mA
mA
mA
µA
8
8
pF
pF
0.7
2.0
2.4
VDDEXT – 0.3
9
10
35
38
100
NOTES
1
Bidirectional pins: D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1–A13, PF0–PF7.
2
Input only pins: RESET, BR, DR0, DR1, PWD.
3
Input only pins: CLKIN, RESET, BR, DR0, DR1, PWD.
4
Output pins: BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK, A0, DT0, DT1, CLKOUT, FL2–0, BGH.
5
Although specified for TTL outputs, all ADSP-2186M outputs are CMOS-compatible and will drive to V DDEXT and GND, assuming no dc loads.
6
Guaranteed but not tested.
7
Three-statable pins: A0–A13, D0–D23, PMS, DMS, BMS, IOMS, CMS, RD, WR, DT0, DT1, SCLK0, SCLK1, TFS0, TFS1, RFS0, RFS1, PF0–PF7.
8
0 V on BR.
9
Idle refers to ADSP-2186M state of operation during execution of IDLE instruction. Deasserted pins are driven to either V DD or GND.
10
IDD measurement taken with all instructions executing from internal memory. 50% of the instructions are multifunction (Types 1, 4, 5, 12, 13, 14), 30% are Type 2
and Type 6, and 20% are idle instructions.
11
VIN = 0 V and 3 V. For typical figures for supply currents, refer to Power Dissipation section.
12
See Chapter 9 of the ADSP-2100 Family User’s Manual for details.
13
Output pin capacitance is the capacitive load for any three-stated output pin.
Specifications subject to change without notice.
–18–
REV. 0
ADSP-2186M
ABSOLUTE MAXIMUM RATINGS 1
Parameter
Internal Supply Voltage (VDDINT)
External Supply Voltage (VDDEXT)
Input Voltage2
Output Voltage Swing3
Operating Temperature Range
Storage Temperature Range
Lead Temperature (5 sec) LQFP
Value
Min
Max
–0.3 V
–0.3 V
–0.5 V
–0.5 V
–40°C
–65°C
+3.0 V
+4.0 V
+4.0 V
VDDEXT + 0.5 V
+85°C
+150°C
NOTES
1
Stresses greater than those listed may cause permanent damage to the device.
These are stress ratings only; functional operation of the device at these or any other
conditions greater than those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
2
Applies to Bidirectional pins (D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0,
TFS1, A1–A13, PF0–PF7) and Input only pins (CLKIN, RESET, BR, DR0,
DR1, PWD).
3
Applies to Output pins (BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK,
A0, DT0, DT1, CLKOUT, FL2–0, BGH).
280°C
ESD SENSITIVITY
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADSP-2186M features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
TIMING SPECIFICATIONS
GENERAL NOTES
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add up parameters to derive longer times.
TIMING NOTES
Switching characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use
switching characteristics to ensure that any timing requirement of a device connected to the processor (such as memory)
is satisfied.
WARNING!
Timing requirements apply to signals that are controlled by
circuitry external to the processor, such as the data input for a
read operation. Timing requirements guarantee that the processor operates correctly with other devices.
MEMORY TIMING SPECIFICATIONS
The table below shows common memory device specifications
and the corresponding ADSP-2186M timing parameters, for
your convenience.
Memory
Device
Specification
Timing
Parameter
Parameter Definition1
Address Setup to
Write Start
Address Setup to
Write End
Address Hold Time
tASW
Data Setup Time
tDW
tAW
tWRA
Data Hold Time
tDH
OE to Data Valid
tRDD
Address Access Time tAA
NOTE
1
xMS = PMS, DMS, BMS, CMS or IOMS.
REV. 0
ESD SENSITIVE DEVICE
–19–
A0–A13, xMS Setup before
WR Low
A0–A13, xMS Setup before
WR Deasserted
A0–A13, xMS Hold before
WR Low
Data Setup before WR
High
Data Hold after WR High
RD Low to Data Valid
A0–A13, xMS to Data Valid
ADSP-2186M
• Each address and data pin has a 10 pF total load at the pin.
FREQUENCY DEPENDENCY FOR TIMING
SPECIFICATIONS
tCK is defined as 0.5 tCKI. The ADSP-2186M uses an input clock
with a frequency equal to half the instruction rate. For example,
a 37.50 MHz input clock (which is equivalent to 26.6 ns) yields
a 13.3 ns processor cycle (equivalent to 75 MHz). tCK values
within the range of 0.5 tCKI period should be substituted for all
relevant timing parameters to obtain the specification value.
• The application operates at VDDEXT = 3.3 V and tCK = 30 ns.
Total Power Dissipation = PINT + (C × VDDEXT2 × f )
PINT = internal power dissipation from Power vs. Frequency
graph (Figure 15).
(C × VDDEXT2 × f ) is calculated for each output:
Example: tCKH = 0.5 tCK – 2 ns = 0.5 (15 ns) – 2 ns = 5.5 ns
ENVIRONMENTAL CONDITIONS
Rating
Description
Symbol
Thermal Resistance
θCA
(Case-to-Ambient)
Thermal Resistance
θJA
(Junction-to-Ambient)
Thermal Resistance
θJC
(Junction-to-Case)
1
LQFP
Mini-BGA
48°C/W
63.3°C/W
50°C/W
70.7°C/W
2°C/W
7.4°C/W
Parameters
# of
Pins
ⴛC
pF
ⴛ VDDEXT2 ⴛ f
V
MHz
PD
mW
Address
Data Output, WR
RD
CLKOUT, DMS
7
9
1
2
10
10
10
10
3.32
3.32
3.32
3.32
12.7
16.3
1.8
7.2
38.0
16.67
16.67
16.67
33.3
Total power dissipation for this example is PINT + 38.0 mW.
Output Drive Currents
Figure 14 shows typical I-V characteristics for the output drivers
on the ADSP-2186M. The curves represent the current drive
capability of the output drivers as a function of output voltage.
NOTE
1
Where the Ambient Temperature Rating (T AMB) is:
TAMB = TCASE – (PD × θCA)
TCASE = Case Temperature in °C
PD = Power Dissipation in W
80
60
VDDEXT = 3.6V @ –40ⴗC
SOURCE CURRENT – mA
POWER DISSIPATION
To determine total power dissipation in a specific application,
the following equation should be applied for each output:
C × VDD 2 × f
C = load capacitance, f = output switching frequency.
Example:
In an application where external data memory is used and no other
outputs are active, power dissipation is calculated as follows:
Assumptions:
40
VDDEXT = 3.3V @ +25ⴗC
20
VDDEXT = 2.5V @ +85ⴗC
0
–20
VDDEXT = 3.6V @ –40ⴗC
VOL
–40
VDDEXT = 2.5V @ +85ⴗC
VDDEXT = 3.3V @ +25ⴗC
–60
–80
• External data memory is accessed every cycle with 50% of the
address pins switching.
VOH
0
0.5
1.0
1.5
2.0
2.5
SOURCE VOLTAGE – V
3.0
3.5
4.0
Figure 14. Typical Output Driver Characteristics
• External data memory writes occur every other cycle with
50% of the data pins switching.
–20–
REV. 0
ADSP-2186M
Capacitive Loading
POWER, INTERNAL1, 2, 3
115
Figure 16 and Figure 17 show the capacitive loading characteristics of the ADSP-2186M.
110mW
110
VDD = 2.65V
100
30
95mW
95
T = 85ⴗC
VDD = 0V TO 2.0V
90
85
VDD = 2.5V
82mW
25
82mW
RISE TIME (0.4V–2.4V) – ns
POWER (PINT) – mW
105
80
75
VDD = 2.35V
70mW
70
65
60
55
61mW
50
55
60
65
1/tCK – MHz
70
75
80
POWER, IDLE1, 2, 4
20
15
10
5
30
28mW
0
VDD = 2.65V
24mW
24mW
24
50
100
150
CL – pF
22
20mW
16
16
14
50
55
60
65
1/tCK – MHz
70
75
80
POWER, IDLE n MODES 2
26
24mW
IDLE
24
VDD = 2.65V
22
20mW
14
12
10
8
6
4
2
NOMINAL
–2
–4
20
–6
18
VDD = 2.5V
IDLE (16)
IDLE (128)
15mW
VDD = 2.35V
0
50
100
150
200
250
CL – pF
16.4mW
Figure 17. Typical Output Valid Delay or Hold vs. Load
Capacitance, CL (at Maximum Ambient Operating
Temperature)
15.7mW
14.25mW
12
50
75
55
60
65
70
80
1/tCK – MHz
NOTES:
VALID FOR ALL TEMPERATURE GRADES.
1 POWER REFLECTS DEVICE OPERATING WITH NO OUTPUT LOADS.
2 TYPICAL POWER DISSIPATION AT 2.5V V
DDINT AND 25ⴗC, EXCEPT
WHERE SPECIFIED.
3I
DD MEASUREMENT TAKEN WITH ALL INSTRUCTIONS EXECUTING FROM
INTERNAL MEMORY. 50% OF THE INSTRUCTIONS ARE MULTIFUNCTION
(TYPES 1, 4, 5, 12, 13, 14), 30% ARE TYPE 2 AND TYPE 6, AND 20% ARE
IDLE INSTRUCTIONS.
4 IDLE REFERS TO STATE OF OPERATION DURING EXECUTION
OF IDLE INSTRUCTION. DEASSERTED PINS ARE DRIVEN TO EITHER VDD
OR GND.
Figure 15. Power vs. Frequency
REV. 0
300
18
VDD = 2.35V
18
14
250
20mW
20
16
200
Figure 16. Typical Output Rise Time vs. Load Capacitance
(at Maximum Ambient Operating Temperature)
VDD = 2.5V
16.5mW
POWER (PIDLEn) – mW
0
26
VALID OUTPUT DELAY OR HOLD – ns
POWER (PIDLE) – mW
28
–21–
ADSP-2186M
TEST CONDITIONS
Output Disable Time
Output Enable Time
Output pins are considered to be disabled when they have stopped
driving and started a transition from the measured output high
or low voltage to a high impedance state. The output disable
time (tDIS) is the difference of tMEASURED and tDECAY, as shown
in the Output Enable/Disable diagram. The time is the interval
from when a reference signal reaches a high or low voltage level
to when the output voltages have changed by 0.5 V from the
measured output high or low voltage.
Output pins are considered to be enabled when they have made
a transition from a high-impedance state to when they start driving.
The output enable time (tENA) is the interval from when a reference signal reaches a high or low voltage level to when the output
has reached a specified high or low trip point, as shown Figure
19. If multiple pins (such as the data bus) are enabled, the measurement value is that of the first pin to start driving.
REFERENCE
SIGNAL
The decay time, tDECAY, is dependent on the capacitive load,
CL, and the current load, iL, on the output pin. It can be
approximated by the following equation:
t DECAY =
tMEASURED
tENA
VOH
(MEASURED)
C L × 0.5V
iL
tDIS
VOH
(MEASURED)
VOH (MEASURED) – 0.5V
2.0V
VOL (MEASURED) +0.5V
1.0V
OUTPUT
from which
VOL
(MEASURED)
VOL
(MEASURED)
tDECAY
tDIS = tMEASURED – tDECAY
INPUT
OUTPUT
STARTS
DRIVING
OUTPUT STOPS
DRIVING
is calculated. If multiple pins (such as the data bus) are disabled,
the measurement value is that of the last pin to stop driving.
HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.
Figure 19. Output Enable/Disable
1.5V
IOL
OUTPUT
2.0V
1.5V
0.8V
Figure 18. Voltage Reference Levels for AC Measurements (Except Output Enable/Disable)
TO
OUTPUT
PIN
1.5V
50pF
IOH
Figure 20. Equivalent Loading for AC Measurements
(Including All Fixtures)
–22–
REV. 0
ADSP-2186M
Parameter
Min
Max
Unit
Timing Requirements:
CLKIN Period
tCKI
tCKIL
CLKIN Width Low
tCKIH
CLKIN Width High
26.6
8
8
80
ns
ns
ns
Switching Characteristics:
tCKL
CLKOUT Width Low
tCKH
CLKOUT Width High
tCKOH
CLKIN High to CLKOUT High
0.5tCK – 2
0.5tCK – 2
0
Control Signals Timing Requirements:
tRSP
RESET Width Low
tMS
Mode Setup before RESET High
tMH
Mode Hold after RESET High
5tCK1
2
5
Clock Signals and Reset
13
ns
ns
ns
ns
ns
ns
NOTE
1
Applies after power-up sequence is complete. Internal phase lock loop requires no more than 2000 CLKIN cycles assuming stable CLKIN (not including crystal
oscillator start-up time).
tCKI
tCKIH
CLKIN
tCKIL
tCKOH
tCKH
CLKOUT
tCKL
PF(3:0)*
tMS
tMH
RESET
*PF3 IS MODE D, PF2 IS MODE C, PF1 IS MODE B, PF0 IS MODE A
Figure 21. Clock Signals
REV. 0
–23–
ADSP-2186M
Parameter
Min
Max
Unit
Interrupts and Flags
Timing Requirements:
IRQx, FI, or PFx Setup before CLKOUT Low1, 2, 3, 4
tIFS
tIFH
IRQx, FI, or PFx Hold after CLKOUT High1, 2, 3, 4
0.25tCK + 10
0.25tCK
Switching Characteristics:
tFOH
Flag Output Hold after CLKOUT Low5
tFOD
Flag Output Delay from CLKOUT Low5
ns
ns
0.5tCK – 5
0.5tCK + 4
ns
ns
NOTES
1
If IRQx and FI inputs meet t IFS and tIFH setup/hold requirements, they will be recognized during the current clock cycle; otherwise the signals will be recognized on
the following cycle. (Refer to “Interrupt Controller Operation” in the Program Control chapter of the ADSP-2100 Family User’s Manual for further information on
interrupt servicing.)
2
Edge-sensitive interrupts require pulsewidths greater than 10 ns; level-sensitive interrupts must be held low until serviced.
3
IRQx = IRQ0, IRQ1, IRQ2, IRQL0, IRQL1, IRQLE.
4
PFx = PF0, PF1, PF2, PF3, PF4, PF5, PF6, PF7.
5
Flag Outputs = PFx, FL0, FL1, FL2, FO.
tFOD
CLKOUT
tFOH
FLAG
OUTPUTS
tIFH
IRQx
FI
PFx
tIFS
Figure 22. Interrupts and Flags
–24–
REV. 0
ADSP-2186M
Parameter
Min
Max
Unit
Bus Request–Bus Grant
Timing Requirements:
BR Hold after CLKOUT High1
tBH
tBS
BR Setup before CLKOUT Low1
0.25tCK + 2
0.25tCK + 10
Switching Characteristics:
tSD
CLKOUT High to xMS, RD, WR Disable
xMS, RD, WR Disable to BG Low
tSDB
tSE
BG High to xMS, RD, WR Enable
tSEC
xMS, RD, WR Enable to CLKOUT High
xMS, RD, WR Disable to BGH Low2
tSDBH
tSEH
BGH High to xMS, RD, WR Enable2
0
0
0.25tCK – 3
0
0
ns
ns
0.25tCK + 8
ns
ns
ns
ns
ns
ns
NOTES
xMS = PMS, DMS, CMS, IOMS, BMS.
1
BR is an asynchronous signal. If BR meets the setup/hold requirements, it will be recognized during the current clock cycle; otherwise the signal will be recognized on
the following cycle. Refer to the ADSP-2100 Family User’s Manual for BR/BG cycle relationships.
2
BGH is asserted when the bus is granted and the processor or BDMA requires control of the bus to continue.
tBH
CLKOUT
BR
tBS
CLKOUT
PMS, DMS
BMS, RD
WR
BG
BGH
tSD
tSEC
tSDB
tSE
tSDBH
tSEH
Figure 23. Bus Request–Bus Grant
REV. 0
–25–
ADSP-2186M
Parameter
Min
Max
Unit
0.5tCK – 5 + w
0.75tCK – 6 + w
ns
ns
ns
Memory Read
Timing Requirements:
RD Low to Data Valid
tRDD
tAA
A0–A13, xMS to Data Valid
tRDH
Data Hold from RD High
0
Switching Characteristics:
tRP
RD Pulsewidth
tCRD
CLKOUT High to RD Low
tASR
A0–A13, xMS Setup before RD Low
A0–A13, xMS Hold after RD Deasserted
tRDA
tRWR
RD High to RD or WR Low
0.5tCK – 3 + w
0.25tCK – 2
0.25tCK – 3
0.25tCK – 3
0.5tCK – 3
0.25tCK + 4
ns
ns
ns
ns
ns
NOTES
w = wait states × tCK.
xMS = PMS, DMS, CMS, IOMS, BMS.
CLKOUT
A0–A13
DMS, PMS,
BMS, IOMS,
CMS
tRDA
RD
tASR
tCRD
tRP
tRWR
D0–D23
tAA
tRDD
tRDH
WR
Figure 24. Memory Read
–26–
REV. 0
ADSP-2186M
Parameter
Min
Max
Unit
Memory Write
Switching Characteristics:
Data Setup before WR High
tDW
tDH
Data Hold after WR High
tWP
WR Pulsewidth
WR Low to Data Enabled
tWDE
tASW
A0–A13, xMS Setup before WR Low
tDDR
Data Disable before WR or RD Low
CLKOUT High to WR Low
tCWR
tAW
A0–A13, xMS, Setup before WR Deasserted
tWRA
A0–A13, xMS Hold after WR Deasserted
tWWR
WR High to RD or WR Low
0.5tCK – 4 + w
0.25tCK – 1
0.5tCK – 3 + w
0
0.25tCK – 3
0.25tCK – 3
0.25tCK – 2
0.75tCK – 5 + w
0.25tCK – 1
0.5tCK – 3
NOTES
w = wait states × tCK.
xMS = PMS, DMS, CMS, IOMS, BMS.
CLKOUT
A0–A13
DMS, PMS,
BMS, CMS,
IOMS
tWRA
WR
tASW
tWWR
tWP
tAW
tDH
tCWR
D0–D23
tDW
tWDE
RD
Figure 25. Memory Write
REV. 0
–27–
tDDR
0.25 tCK + 4
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADSP-2186M
Serial Ports
Parameter
Min
Max
Unit
Serial Ports
Timing Requirements:
tSCK
SCLK Period
tSCS
DR/TFS/RFS Setup before SCLK Low
DR/TFS/RFS Hold after SCLK Low
tSCH
tSCP
SCLKIN Width
26.6
4
7
12
Switching Characteristics:
tCC
CLKOUT High to SCLKOUT
SCLK High to DT Enable
tSCDE
tSCDV
SCLK High to DT Valid
tRH
TFS/RFSOUT Hold after SCLK High
TFS/RFSOUT Delay from SCLK High
tRD
tSCDH
DT Hold after SCLK High
tTDE
TFS (Alt) to DT Enable
TFS (Alt) to DT Valid
tTDV
tSCDD
SCLK High to DT Disable
tRDV
RFS (Multichannel, Frame Delay Zero) to DT Valid
CLKOUT
tCC
ns
ns
ns
ns
0.25tCK
0
0.25tCK + 6
12
0
12
0
0
12
12
12
tCC
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSCK
SCLK
tSCP
tSCS
tSCP
tSCH
DR
TFSIN
RFSIN
tRD
tRH
RFSOUT
TFSOUT
tSCDD
tSCDV
tSCDH
tSCDE
DT
tTDE
tTDV
TFSOUT
ALTERNATE
FRAME MODE
tRDV
RFSOUT
MULTICHANNEL
MODE,
FRAME DELAY 0
(MFD = 0)
TFSIN
tTDE
tTDV
ALTERNATE
FRAME MODE
RFSIN
MULTICHANNEL
MODE,
FRAME DELAY 0
(MFD = 0)
tRDV
Figure 26. Serial Ports
–28–
REV. 0
ADSP-2186M
Parameter
Min
Max
Unit
IDMA Address Latch
Timing Requirements:
Duration of Address Latch1, 2
tIALP
tIASU
IAD15–0 Address Setup before Address Latch End2
tIAH
IAD15–0 Address Hold after Address Latch End2
IACK Low before Start of Address Latch2, 3
tIKA
tIALS
Start of Write or Read after Address Latch End2, 3
tIALD
Address Latch Start after Address Latch End1, 2
10
5
3
0
3
2
ns
ns
ns
ns
ns
ns
NOTES
1
Start of Address Latch = IS Low and IAL High.
2
End of Address Latch = IS High or IAL Low.
3
Start of Write or Read = IS Low and IWR Low or IRD Low.
IACK
tIKA
tIALD
IAL
tIALP
tIALP
IS
IAD15–0
tIASU
tIAH
tIASU
RD OR WR
Figure 27. IDMA Address Latch
REV. 0
–29–
tIAH
tIALS
ADSP-2186M
Parameter
Min
Max
Unit
IDMA Write, Short Write Cycle
Timing Requirements:
IACK Low before Start of Write1
tIKW
tIWP
Duration of Write1, 2
tIDSU
IAD15–0 Data Setup before End of Write2, 3, 4
IAD15–0 Data Hold after End of Write2, 3, 4
tIDH
0
10
3
2
Switching Characteristic:
tIKHW
Start of Write to IACK High
ns
ns
ns
ns
10
ns
NOTES
1
Start of Write = IS Low and IWR Low.
2
End of Write = IS High or IWR High.
3
If Write Pulse ends before IACK Low, use specifications t IDSU, tIDH.
4
If Write Pulse ends after IACK Low, use specifications t IKSU, tIKH.
tIKW
IACK
tIKHW
IS
tIWP
IWR
tIDSU
IAD15–0
tIDH
DATA
Figure 28. IDMA Write, Short Write Cycle
–30–
REV. 0
ADSP-2186M
Parameter
Min
Max
Unit
IDMA Write, Long Write Cycle
Timing Requirements:
IACK Low before Start of Write1
tIKW
IAD15–0 Data Setup before End of Write2, 3, 4
tIKSU
tIKH
IAD15–0 Data Hold after End of Write2, 3, 4
0
0.5tCK + 5
0
Switching Characteristics:
tIKLW
Start of Write to IACK Low4
tIKHW
Start of Write to IACK High
ns
ns
ns
1.5tCK
10
NOTES
1
Start of Write = IS Low and IWR Low.
2
If Write Pulse ends before IACK Low, use specifications t IDSU, tIDH.
3
If Write Pulse ends after IACK Low, use specifications t IKSU, tIKH.
4
This is the earliest time for IACK Low from Start of Write. For IDMA Write cycle relationships, please refer to the ADSP-2100 Family User’s Manual.
tIKW
IACK
tIKHW
tIKLW
IS
IWR
tIKSU
tIKH
DATA
IAD15–0
Figure 29. IDMA Write, Long Write Cycle
REV. 0
–31–
ns
ns
ADSP-2186M
Parameter
Min
Max
Unit
IDMA Read, Long Read Cycle
Timing Requirements:
IACK Low before Start of Read1
tIKR
tIRK
End of Read after IACK Low2
0
2
Switching Characteristics:
tIKHR
IACK High after Start of Read1
IAD15–0 Data Setup before IACK Low
tIKDS
tIKDH
IAD15–0 Data Hold after End of Read2
tIKDD
IAD15–0 Data Disabled after End of Read2
IAD15–0 Previous Data Enabled after Start of Read
tIRDE
tIRDV
IAD15–0 Previous Data Valid after Start of Read
tIRDH1
IAD15–0 Previous Data Hold after Start of Read (DM/PM1)3
tIRDH2
IAD15–0 Previous Data Hold after Start of Read (PM2)4
ns
ns
10
0.5tCK – 2
0
10
0
11
2tCK – 5
tCK – 5
ns
ns
ns
ns
ns
ns
ns
ns
NOTES
1
Start of Read = IS Low and IRD Low.
2
End of Read = IS High or IRD High.
3
DM read or first half of PM read.
4
Second half of PM read.
IACK
tIKHR
tIKR
IS
tIRK
IRD
tIKDH
tIKDS
tIRDE
PREVIOUS
DATA
IAD15–0
READ
DATA
tIRDV
tIKDD
tIRDH
Figure 30. IDMA Read, Long Read Cycle
–32–
REV. 0
ADSP-2186M
Parameter
IDMA Read, Short Read Cycle
Min
Max
Unit
0
10
10
2tCK – 5
tCK – 5
ns
ns
ns
1, 2
Timing Requirements:
IACK Low before Start of Read3
tIKR
tIRP1
Duration of Read (DM/PM1)4
tIRP2
Duration of Read (PM2)5
Switching Characteristics:
tIKHR
IACK High after Start of Read3
tIKDH
IAD15–0 Data Hold after End of Read6
tIKDD
IAD15–0 Data Disabled after End of Read6
IAD15–0 Previous Data Enabled after Start of Read
tIRDE
tIRDV
IAD15–0 Previous Data Valid after Start of Read
10
0
10
0
10
NOTES
1
Short Read Only must be disabled in the IDMA Overlay memory mapped register.
2
Consider using the Short Read Only mode, instead, because Short Read mode is not applicable at high clock frequencies.
3
Start of Read = IS Low and IRD Low.
4
DM Read or first half of PM Read.
5
Second half of PM Read.
6
End of Read = IS High or IRD High.
IACK
tIKR
tIKHR
IS
tIRP
IRD
tIKDH
tIRDE
PREVIOUS
DATA
IAD15–0
tIRDV
tIKDD
Figure 31. IDMA Read, Short Read Cycle
REV. 0
–33–
ns
ns
ns
ns
ns
ADSP-2186M
Parameter
Min
IDMA Read, Short Read Cycle in Short Read Only Mode
Max
Unit
1
Timing Requirements:
IACK Low before Start of Read2
tIKR
tIRP
Duration of Read3
0
10
Switching Characteristics:
tIKHR
IACK High after Start of Read2
IAD15–0 Previous Data Hold after End of Read3
tIKDH
tIKDD
IAD15–0 Previous Data Disabled after End of Read3
tIRDE
IAD15–0 Previous Data Enabled after Start of Read
tIRDV
IAD15–0 Previous Data Valid after Start of Read
ns
ns
10
0
10
0
10
ns
ns
ns
ns
ns
NOTES
1
Short Read Only is enabled by setting Bit 14 of the IDMA Overlay Register to 1 (0x3FE7). Short Read Only can be enabled by the processor core writing to the
register or by an external host writing to the register. Disabled by default.
2
Start of Read = IS Low and IRD Low. Previous data remains until end of read.
3
End of Read = IS High or IRD High.
IACK
tIKR
tIKHR
IS
tIRP
IRD
tIKDH
tIRDE
PREVIOUS
DATA
IAD15–0
tIRDV
tIKDD
Figure 32. IDMA Read, Short Read Only Cycle
–34–
REV. 0
ADSP-2186M
A4/IAD3
A5/IAD4
1
2
78 D18
77 D17
76 D16
80 GND
79 D19
82 D21
81 D20
84 D23
83 D22
86 FL1
85 FL2
87 FL0
89 PF2 [MODE C]
88 PF3 [MODE D]
91 PWD
90 VDDEXT
92 GND
94 PF0 [MODE A]
93 PF1 [MODE B]
95 BGH
96 PWDACK
98 A1/IAD0
97 A0
100 A3/IAD2
99 A2/IAD1
100-LEAD LQFP PIN CONFIGURATION
75 D15
74 D14
PIN 1
IDENTIFIER
GND
3
A6/IAD5
A7/IAD6
4
73 D13
72 D12
5
71 GND
A8/IAD7
A9/IAD8
6
70 D11
69 D10
A10/IAD9
8
7
68 D9
67 VDDEXT
A11/IAD10 9
A12/IAD11 10
66 GND
A13/IAD12 11
GND 12
65 D8
64 D7/IWR
ADSP-2186M
CLKIN 13
63 D6/IRD
TOP VIEW
(Not to Scale)
XTAL 14
VDDEXT 15
62 D5/IAL
61 D4/IS
CLKOUT 16
GND 17
VDDINT 18
60 GND
59 VDD INT
58 D3/IACK
WR 19
RD 20
57 D2/IAD15
BMS 21
55 D0/IAD13
DMS 22
PMS 23
54 BG
53 EBG
IOMS 24
CMS 25
52 BR
51 EBR
–35–
EINT 50
ELIN 49
ELOUT 48
EE 46
ECLK 47
EMS 45
SCLK1 42
ERESET 43
RESET 44
GND 41
DR1/FI 40
RFS1/IRQ0 39
DT1/FO 37
TFS1/IRQ1 38
DR0 34
SCLK0 35
VDDEXT 36
TFS0 32
RFS0 33
IRQ2+PF7 30
DT0 31
GND 28
IRQL1+PF6 29
IRQE+PF4 26
REV. 0
IRQL0+PF5 27
56 D1/IAD14
ADSP-2186M
The LQFP package pinout is shown in the table below. Pin names in bold text replace the plain text named functions when
Mode C = 1. A + sign separates two functions when either function can be active for either major I/O mode. Signals enclosed in
brackets [ ] are state bits latched from the value of the pin at the deassertion of RESET.
The multiplexed pins DT1/FO, TFS1/IRQ1, RFS1/IRQ0, and DR1/FI, are mode selectable by setting Bit 10 (SPORT1 configure)
of the System Control Register. If Bit 10 = 1, these pins have serial port functionality. If Bit 10 = 0, these pins are the external interrupt and flag pins. This bit is set to 1 by default upon reset.
LQFP Package Pinout
Pin
No.
Pin Name
Pin
No.
Pin Name
Pin
No.
Pin Name
Pin
No.
Pin Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
A4/IAD3
A5/IAD4
GND
A6/IAD5
A7/IAD6
A8/IAD7
A9/IAD8
A10/IAD9
A11/IAD10
A12/IAD11
A13/IAD12
GND
CLKIN
XTAL
VDDEXT
CLKOUT
GND
VDDINT
WR
RD
BMS
DMS
PMS
IOMS
CMS
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
IRQE + PF4
IRQL0 + PF5
GND
IRQL1 + PF6
IRQ2 + PF7
DT0
TFS0
RFS0
DR0
SCLK0
VDDEXT
DT1/FO
TFS1/IRQ1
RFS1/IRQ0
DR1/FI
GND
SCLK1
ERESET
RESET
EMS
EE
ECLK
ELOUT
ELIN
EINT
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
EBR
BR
EBG
BG
D0/IAD13
D1/IAD14
D2/IAD15
D3/IACK
VDDINT
GND
D4/IS
D5/IAL
D6/IRD
D7/IWR
D8
GND
VDDEXT
D9
D10
D11
GND
D12
D13
D14
D15
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
D16
D17
D18
D19
GND
D20
D21
D22
D23
FL2
FL1
FL0
PF3 [MODE D]
PF2 [MODE C]
VDDEXT
PWD
GND
PF1 [MODE B]
PF0 [MODE A]
BGH
PWDACK
A0
A1/IAD0
A2/IAD1
A3/IAD2
–36–
REV. 0
ADSP-2186M
144-Ball Mini-BGA Package Pinout (Bottom View)
12
11
10
9
8
7
6
5
4
3
2
1
GND
GND
D22
NC
NC
NC
GND
NC
A0
GND
A1/IAD0
A2/IAD1
A
D16
D17
D18
D20
D23
VDDEXT
GND
NC
NC
GND
A3/IAD2
A4/IAD3
B
D14
NC
D15
D19
D21
VDDEXT
PWD
A7/IAD6
A5/IAD4
RD
A6/IAD5
PWDACK
C
GND
NC
D12
D13
NC
PF2
[MODE C]
PF1
[MODE B]
A9/IAD8
BGH
NC
WR
NC
D
D10
GND
VDDEXT
GND
GND
PF3
[MODE D]
FL2
PF0
[MODE A]
FL0
A8/IAD7
VDDEXT
VDDEXT
E
D9
NC
D8
D11
D7/IWR
NC
NC
FL1
A11/IAD10
A12/IAD11
NC
A13/IAD12
F
D4/IS
NC
NC
D5/IAL
D6/IRD
NC
NC
NC
A10/IAD9
GND
NC
XTAL
G
GND
NC
GND
D3/IACK
D2/IAD15
TFS0
DT0
VDDINT
GND
GND
GND
CLKIN
H
VDDINT
VDDINT
D1/IAD14
BG
RFS1/IRQ0
D0/IAD13
SCLK0
VDDEXT
VDDEXT
NC
VDDINT
CLKOUT
J
EBG
BR
EBR
ERESET
SCLK1
TFS1/IRQ1
RFS0
DMS
BMS
NC
NC
NC
K
EINT
ELOUT
ELIN
RESET
GND
DR0
PMS
GND
IOMS
IRQL1 + PF6
NC
IRQE + PF4
L
ECLK
EE
EMS
NC
GND
DR1/FI
DT1/FO
GND
CMS
NC
IRQ2 + PF7
IRQL0 + PF5
M
REV. 0
–37–
ADSP-2186M
The Mini-BGA package pinout is shown in the table below. Pin names in bold text replace the plain text named functions when
Mode C = 1. A + sign separates two functions when either function can be active for either major I/O mode. Signals enclosed in
brackets [ ] are state bits latched from the value of the pin at the deassertion of RESET.
The multiplexed pins DT1/FO, TFS1/IRQ1, RFS1/IRQ0, and DR1/FI, are mode selectable by setting Bit 10 (SPORT1 configure) of
the System Control Register. If Bit 10 = 1, these pins have serial port functionality. If Bit 10 = 0, these pins are the external interrupt
and flag pins. This bit is set to 1 by default upon reset.
Mini-BGA Package Pinout
Ball #
Pin Name
Ball #
Pin Name
Ball #
Pin Name
Ball #
Pin Name
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A2/IAD1
A1/IAD0
GND
A0
NC
GND
NC
NC
NC
D22
GND
GND
D01
D02
D03
D04
D05
D06
D07
D08
D09
D10
D11
D12
NC
WR
NC
BGH
A9/IAD8
PF1 [MODE B]
PF2 [MODE C]
NC
D13
D12
NC
GND
G01
G02
G03
G04
G05
G06
G07
G08
G09
G10
G11
G12
XTAL
NC
GND
A10/IAD9
NC
NC
NC
D6/IRD
D5/IAL
NC
NC
D4/IS
K01
K02
K03
K04
K05
K06
K07
K08
K09
K10
K11
K12
NC
NC
NC
BMS
DMS
RFS0
TFS1/IRQ1
SCLK1
ERESET
EBR
BR
EBG
B01
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
A4/IAD3
A3/IAD2
GND
NC
NC
GND
VDDEXT
D23
D20
D18
D17
D16
E01
E02
E03
E04
E05
E06
E07
E08
E09
E10
E11
E12
VDDEXT
VDDEXT
A8/IAD7
FL0
PF0 [MODE A]
FL2
PF3 [MODE D]
GND
GND
VDDEXT
GND
D10
H01
H02
H03
H04
H05
H06
H07
H08
H09
H10
H11
H12
CLKIN
GND
GND
GND
VDDINT
DT0
TFS0
D2/IAD15
D3/IACK
GND
NC
GND
L01
L02
L03
L04
L05
L06
L07
L08
L09
L10
L11
L12
IRQE + PF4
NC
IRQL1 + PF6
IOMS
GND
PMS
DR0
GND
RESET
ELIN
ELOUT
EINT
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
PWDACK
A6/IAD5
RD
A5/IAD4
A7/IAD6
PWD
VDDEXT
D21
D19
D15
NC
D14
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
A13/IAD12
NC
A12/IAD11
A11/IAD10
FL1
NC
NC
D7/IWR
D11
D8
NC
D9
J01
J02
J03
J04
J05
J06
J07
J08
J09
J10
J11
J12
CLKOUT
VDDINT
NC
VDDEXT
VDDEXT
SCLK0
D0/IAD13
RFS1/IRQ0
BG
D1/IAD14
VDDINT
VDDINT
M01
M02
M03
M04
M05
M06
M07
M08
M09
M10
M11
M12
IRQL0 + PF5
IRQL2 + PF7
NC
CMS
GND
DT1/FO
DR1/FI
GND
NC
EMS
EE
ECLK
–38–
REV. 0
ADSP-2186M
OUTLINE DIMENSIONS
Dimensions shown in millimeters.
100-Lead Metric Thin Plastic Quad Flatpack (LQFP)
(ST-100)
16.20
16.00 TYP SQ
15.80
14.05
14.00 TYP SQ
13.95
1.60 MAX
0.75
0.60 TYP
0.50
12.00 BSC
12ⴗ
TYP
100
1
76
75
SEATING
PLANE
TOP VIEW
(PINS DOWN)
0.08
MAX LEAD
COPLANARITY
0ⴗ – 7ⴗ
6ⴗ ± 4ⴗ
25
26
51
50
0.50
BSC
0.15
0.05
LEAD PITCH
0.27
0.22 TYP
0.17
LEAD WIDTH
NOTE:
THE ACTUAL POSITION OF EACH LEAD IS WITHIN 0.08 FROM ITS IDEAL
POSITION WHEN MEASURED IN THE LATERAL DIRECTION.
REV. 0
–39–
ADSP-2186M
OUTLINE DIMENSIONS
Dimensions shown in millimeters.
10.10
10.00 SQ
9.90
C02048–3.5–10/00 (rev. 0)
144-Ball Mini-BGA
(CA-144)
12 11 10 9 8 7 6 5 4 3 2 1
8.80
BSC
10.10
10.00 SQ
9.90
TOP VIEW
A
B
C
D
E
F
G
H
J
K
L
M
0.80
BSC
0.80 BSC
8.80 BSC
DETAIL A
1.40 MAX
DETAIL A
NOTES:
1. THE ACTUAL POSITION OF THE BALL POPULATION
IS WITHIN 0.150 OF ITS IDEAL POSITION RELATIVE
TO THE PACKAGE EDGES.
2. THE ACTUAL POSITION OF EACH BALL IS WITHIN 0.08
OF ITS IDEAL POSITION RELATIVE TO THE BALL
POPULATION.
1.00
0.85
0.40
0.25
0.55
0.12
MAX
0.50
0.45
BALL DIAMETER
SEATING
PLANE
ORDERING GUIDE
Part Number
Ambient Temperature
Range
Instruction
Rate
Package
Description*
Package
Option
ADSP-2186MKST-300
ADSP-2186MBST-266
ADSP-2186MKCA-300
ADSP-2186MBCA-266
0°C to 70°C
–40°C to +85°C
0°C to 70°C
–40°C to +85°C
75
66
75
66
100-Lead LQFP
100-Lead LQFP
144-Ball Mini-BGA
144-Ball Mini-BGA
ST-100
ST-100
CA-144
CA-144
PRINTED IN U.S.A.
*In 1998, JEDEC reevaluated the specifications for the TQFP package designation, assigning it to packages 1.0 mm thick. Previously labeled TQFP packages (1.6 mm
thick) are now designated as LQFP.
–40–
REV. 0