TI LM79L12ACM Series 3-terminal negative regulator Datasheet

LM79L05AC is OBSOLETE
LM79L05, LM79L12, LM79L12AC
LM79L15, LM79L15AC
www.ti.com
SNOSBR8K – JULY 1999 – REVISED APRIL 2013
LM79LXXAC Series 3-Terminal Negative Regulators
Check for Samples: LM79L05, LM79L12, LM79L12AC, LM79L15, LM79L15AC
FEATURES
DESCRIPTION
•
The LM79LXXAC series of 3-terminal negative
voltage regulators features fixed output voltages of
−5V, −12V, and −15V with output current capabilities
in excess of 100mA. These devices were designed
using the latest computer techniques for optimizing
the packaged IC thermal/electrical performance. The
LM79LXXAC series, when combined with a minimum
output capacitor of 0.1μF, exhibits an excellent
transient response, a maximum line regulation of
0.07% VO/V, and a maximum load regulation of
0.01% VO/mA.
1
2
•
•
•
•
•
•
•
Preset Output Voltage Error is Less than ±5%
Over Load, Line and Temperature
Specified at an Output Current of 100mA
Easily Compensated with a Small 0.1μF Output
Capacitor
Internal Short-Circuit, Thermal and Safe
Operating Area Protection
Easily Adjustable to Higher Output Voltages
Maximum Line Regulation Less than 0.07%
VOUT/V
Maximum Load Regulation Less than 0.01%
VOUT/mA
See AN-1112 (SNVA009) for DSBGA
Considerations
The LM79LXXAC series also includes, as selfprotection circuitry: safe operating area circuitry for
output transistor power dissipation limiting, a
temperature independent short circuit current limit for
peak output current limiting, and a thermal shutdown
circuit to prevent excessive junction temperature.
Although designed primarily as fixed voltage
regulators, these devices may be combined with
simple external circuitry for boosted and/or adjustable
voltages and currents. The LM79LXXAC series is
available in the 3-lead TO package, the 8-lead SOIC
package, and the 6-Bump DSBGA package.
For output voltages other than the pre-set -5V, -12V
and -15V, the LM137L series provides an adjustable
output voltage range from -1.2V to -47V.
Typical Applications
*Required if the regulator is located far from the power supply filter.
A 1μF aluminum electrolytic may be substituted.
**Required for stability. A 1μF aluminum electrolytic may be
substituted.
Figure 1. Fixed Output Regulator
−V0 = −5V − (5V/R1 + IQ) • R2,
5V/R1 > 3 IQ
Figure 2. Adjustable Output Regulator
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LM79L05AC is OBSOLETE
LM79L05, LM79L12, LM79L12AC
LM79L15, LM79L15AC
SNOSBR8K – JULY 1999 – REVISED APRIL 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Connection Diagram
1
-VIN
2
-VIN
3
NC
4
LM79LXXACM
-VOUT
8
NC
7
-VIN
6
-VIN
5
GND
Pins labeled 'NC' on LM79LXXACM 8-Lead SOIC (pin 4 and pin 8) are Open, no internal connection.
Figure 3. 8-Lead SOIC Narrow (D)
Top View
Figure 4. 3–Lead TO-226 (LP)
Bottom View
GND
-VOUT
-VIN
A2
B2
C2
A1
B1
C1
GND
-VOUT
-VIN
Figure 5. 6-Bump DSBGA
Top View (Bump Side Down)
2
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM79L05 LM79L12 LM79L12AC LM79L15 LM79L15AC
LM79L05AC is OBSOLETE
LM79L05, LM79L12, LM79L12AC
LM79L15, LM79L15AC
www.ti.com
SNOSBR8K – JULY 1999 – REVISED APRIL 2013
Absolute Maximum Ratings (1) (2)
Input Voltage
VO = −5V, −12V, −15V
Internal Power Dissipation
−35V
(3)
Internally Limited
Operating Temperature Range
0°C to +70°C
Maximum Junction Temperature
+125°C
−55°C to +150°C
Storage Temperature Range
Lead Temperature
(Soldering, 10 sec.)
(1)
(2)
(3)
260°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Thermal resistance of TO-226 (LP) package is 60°C/W θJC, 232°C/W θJA at still air, and 88°C/W at 400 ft/min of air. The θJA of the
LM78LXX in the 6-Bump DSBGA package is 114°C/W when mounted on a 4-Layer JEDEC test board (JESD 51-7). The θJA of the
LM78LXX in the SOIC-8 (D) package is 180°C/W in still air. The maximum junction temperature shall not exceed 125°C on electrical
parameters.
Electrical Characteristics
(1)
TA = 0°C to +70°C unless otherwise noted.
−5V
Output Voltage
−10V
Input Voltage (unless otherwise noted)
Symbol
VO
Parameter
Output
Voltage
Conditions
Line
Regulation
Min
Typ
Max
Min
Typ
Max
TJ = 25°C, IO = 100mA
−5.2
−5
−4.8
−12.5
−12
−11.5
−15.6
−15
−14.4
1mA ≤ IO ≤ 100mA
−5.25
−4.75
−12.6
−11.4
−15.7
5
VMIN ≤ VIN ≤ VMAX
(−20 ≤ VIN ≤ −7.5)
1mA ≤ IO ≤ 40mA
−5.25
VMIN ≤ VIN ≤ VMAX
(−20 ≤ VIN ≤ −7)
VMIN ≤ VIN ≤ VMAX
−4.75
(−30 ≤ VIN ≤ −18)
−12.6
−15.7
5
−11.4
(−27 ≤ VIN ≤ −14.5)
(−20 ≤ VIN ≤ −7.3)
60
TJ = 25°C
Load
Regulation
ΔVO
Long Term
Stability
IO = 100mA
20
IQ
Quiescent
Current
IO = 100mA
2
ΔIQ
Quiescent
Current
Change
(−30 ≤ VIN ≤ −17.5)
45
(−30 ≤ VIN ≤ −17.7)
45
(−27 ≤ VIN ≤ −14.5)
50
V
−14.25
45
(−27 ≤ VIN ≤ −14.6)
(−20 ≤ VIN ≤ −7)
Units
−14.25
(−27 ≤ VIN ≤ −14.8)
60
TJ = 25°C, IO = 40mA
45
(−30 ≤ VIN ≤ −17.5)
100
125
mV
V
mV
V
mV
1mA ≤ IO ≤ 100mA
48
6
mV/kh
rs
60
2
6
2
6
mA
1mA ≤ IO ≤ 100mA
0.3
0.3
0.3
1mA ≤ IO ≤ 40mA
0.1
0.1
0.1
mA
0.25
mA
IO = 100mA
VMIN ≤ VIN ≤ VMAX
(1)
−20V
Max
ΔVO
ΔVIN/ΔVO
−17V
Typ
VMIN ≤ VIN ≤ VMAX
Vn
−15V
Min
TJ = 25°C, IO = 100mA
ΔVO
−12V
0.25
(−20 ≤ VIN ≤ −7.5)
0.25
(−27 ≤ VIN ≤ −14.8)
(−30 ≤ VIN ≤ −18)
V
Output Noise
Voltage
TJ = 25°C, IO = 100mA
f = 10Hz − 10kHz
Ripple
Rejection
TJ = 25°C, IO = 100mA
f = 120Hz
Input Voltage
Required to
TJ = 25°C, IO = 100mA
−7.3
−14.6
−17.7
V
Maintain Line
Regulation
IO = 40mA
−7.0
−14.5
−17.5
V
40
96
50
μV
120
52
50
dB
To ensure constant junction temperature, low duty cycle pulse testing is used.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM79L05 LM79L12 LM79L12AC LM79L15 LM79L15AC
3
LM79L05AC is OBSOLETE
LM79L05, LM79L12, LM79L12AC
LM79L15, LM79L15AC
SNOSBR8K – JULY 1999 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
4
Maximum Average Power Dissipation (TO-226)
Peak Output Current
Figure 6.
Figure 7.
Short Circuit Output Current
Dropout Voltage
Figure 8.
Figure 9.
Ripple Rejection
Output Voltage vs. Temperature
(Normalized to 1V @ 25°C)
Figure 10.
Figure 11.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM79L05 LM79L12 LM79L12AC LM79L15 LM79L15AC
LM79L05AC is OBSOLETE
LM79L05, LM79L12, LM79L12AC
LM79L15, LM79L15AC
www.ti.com
SNOSBR8K – JULY 1999 – REVISED APRIL 2013
Typical Performance Characteristics (continued)
Quiescent Current
Output Impedance
Figure 12.
Figure 13.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM79L05 LM79L12 LM79L12AC LM79L15 LM79L15AC
5
LM79L05AC is OBSOLETE
LM79L05, LM79L12, LM79L12AC
LM79L15, LM79L15AC
SNOSBR8K – JULY 1999 – REVISED APRIL 2013
www.ti.com
TYPICAL APPLICATIONS
Figure 14. ±15V, 100mA Dual Power Supply
Schematic Diagrams
Figure 15. −5V Schematic Diagram
6
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM79L05 LM79L12 LM79L12AC LM79L15 LM79L15AC
LM79L05AC is OBSOLETE
LM79L05, LM79L12, LM79L12AC
LM79L15, LM79L15AC
www.ti.com
SNOSBR8K – JULY 1999 – REVISED APRIL 2013
Figure 16. −12V and −15V Schematic Diagram
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM79L05 LM79L12 LM79L12AC LM79L15 LM79L15AC
7
LM79L05AC is OBSOLETE
LM79L05, LM79L12, LM79L12AC
LM79L15, LM79L15AC
SNOSBR8K – JULY 1999 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision J (April 2013) to Revision K
•
8
Page
Changed layout of National Data Sheet to TI format ............................................................................................................ 7
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM79L05 LM79L12 LM79L12AC LM79L15 LM79L15AC
PACKAGE OPTION ADDENDUM
www.ti.com
16-Jun-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM79L05ACM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
0 to 70
LM79L
05ACM
LM79L05ACM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM79L
05ACM
LM79L05ACMX
NRND
SOIC
D
8
2500
TBD
Call TI
Call TI
0 to 70
LM79L
05ACM
LM79L05ACMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM79L
05ACM
LM79L05ACTL/NOPB
ACTIVE
DSBGA
YZR
6
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
0 to 70
P
B
LM79L05ACTLX/NOPB
ACTIVE
DSBGA
YZR
6
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
0 to 70
P
B
LM79L05ACZ/LFT1
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
LM79L05ACZ/NOPB
ACTIVE
TO-92
LP
3
1800
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
0 to 70
320L
79L05
LM79L12ACM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
0 to 70
LM79L
12ACM
LM79L12ACM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM79L
12ACM
LM79L12ACMX
NRND
SOIC
D
8
2500
TBD
Call TI
Call TI
0 to 70
LM79L
12ACM
LM79L12ACMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM79L
12ACM
LM79L12ACZ/LFT4
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
LM79L12ACZ/NOPB
ACTIVE
TO-92
LP
3
1800
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
0 to 70
320L
79L12
LM79L15ACM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
0 to 70
LM79L
15ACM
LM79L15ACM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM79L
15ACM
LM79L15ACMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 70
LM79L
15ACM
Addendum-Page 1
320L
79L05
320L
79L12
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
16-Jun-2015
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LM79L05ACMX
Package Package Pins
Type Drawing
SOIC
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
D
8
2500
330.0
12.4
6.5
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
5.4
2.0
8.0
12.0
Q1
LM79L05ACMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM79L05ACTL/NOPB
DSBGA
YZR
6
250
178.0
8.4
1.09
1.88
0.76
4.0
8.0
Q1
LM79L05ACTLX/NOPB
DSBGA
YZR
6
3000
178.0
8.4
1.09
1.88
0.76
4.0
8.0
Q1
LM79L12ACMX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM79L12ACMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM79L15ACMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM79L05ACMX
SOIC
D
8
2500
367.0
367.0
35.0
LM79L05ACMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LM79L05ACTL/NOPB
DSBGA
YZR
6
250
210.0
185.0
35.0
LM79L05ACTLX/NOPB
DSBGA
YZR
6
3000
210.0
185.0
35.0
LM79L12ACMX
SOIC
D
8
2500
367.0
367.0
35.0
LM79L12ACMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LM79L15ACMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
YZR0006xxx
D
0.600±0.075
E
TLA06XXX (Rev C)
D: Max = 1.845 mm, Min =1.784 mm
E: Max = 1.057 mm, Min =0.996 mm
4215044/A
NOTES:
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
www.ti.com
12/12
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages