DATA SHEET 128M bits SDRAM WTR (Wide Temperature Range) EDS1232AATA-MI (4M words × 32 bits) Description Pin Configurations The EDS1232AA is a 128M bits SDRAM organized as 1,048,576 words × 32 bits × 4 banks. All inputs and outputs are synchronized with the positive edge of the clock. They are packaged in 86-pin plastic TSOP (II). /xxx indicates active low signal. EO 86-pin Plastic TSOP(II) Features • • • • • L 3.3V power supply Clock frequency: 133MHz (max.) Single pulsed /RAS ×32 organization 4 banks can operate simultaneously and independently • Burst read/write operation and burst read/single write operation capability • Programmable burst length (BL): 1, 2, 4, 8 and full page • 2 variations of burst sequence ⎯ Sequential (BL = 1, 2, 4, 8, full page) ⎯ Interleave (BL = 1, 2, 4, 8) • Programmable /CAS latency (CL): 2, 3 • Byte control by DQM • Refresh cycles: 4096 refresh cycles/64ms • 2 variations of refresh ⎯ Auto refresh ⎯ Self refresh • Ambient temperature range: –40 to +85°C Pr A0 to A11, BA0, BA1 VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 NC VDD DQM0 /WE /CAS /RAS /CS A11 BA0 BA1 A10(AP) A0 A1 A2 DQM2 VDD NC DQ16 VSSQ DQ17 DQ18 VDDQ DQ19 DQ20 VSSQ DQ21 DQ22 VDDQ DQ23 VDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 NC VSS DQM1 NC NC CLK CKE A9 A8 A7 A6 A5 A4 A3 DQM3 VSS NC DQ31 VDDQ DQ30 DQ29 VSSQ DQ28 DQ27 VDDQ DQ26 DQ25 VSSQ DQ24 VSS (Top view) DQM0 to DQM3 DQ mask enable od Address inputs Bank select DQ0 to DQ31 Data input/output /CS Chip select /RAS Row address strobe Column address strobe /CAS Write enable /WE CKE CLK VDD VSS VDDQ VSSQ NC Clock enable Clock input Supply voltage Ground Supply voltage for DQ Ground for DQ No connection t uc Document No. E0340E30 (Ver. 3.0) Date Published January 2007 (K) Japan Printed in Japan URL: http://www.elpida.com This product became EOL in April, 2007. ©Elpida Memory, Inc. 2003-2007 EDS1232AATA-MI Ordering Information Supply voltage Part number EDS1232AATA-75MI 3.3V Organization (words × bits) Internal Banks Clock frequency MHz (max.) /CAS latency Package 4M × 32 133 100 3 2 86-pin plastic TSOP (II) Part Number E D S 12 32 A A TA - 75 MI Elpida Memory EO Type D: Monolithic Device Spec. Detail MI: WTR (−40 to +85°C) & Low Power Product Code S: SDRAM Density / Bank 12: 128M/4 Banks Speed 75: 133MHz/CL3 100MHz/CL2 Bit Organization 32: x32 Voltage, Interface A: 3.3V, LVTTL L Die Rev. Package TA: TSOP (II) t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 2 EDS1232AATA-MI CONTENTS Description .................................................................................................................................................... 1 Features ........................................................................................................................................................ 1 Pin Configurations......................................................................................................................................... 1 Ordering Information ..................................................................................................................................... 2 Part Number.................................................................................................................................................. 2 Electrical Specifications ................................................................................................................................ 4 Block Diagram............................................................................................................................................... 9 Pin Function ................................................................................................................................................ 10 EO Command Operation................................................................................................................................... 11 Truth Table.................................................................................................................................................. 15 Simplified State Diagram ............................................................................................................................ 21 Programming Mode Registers .................................................................................................................... 22 Mode Register............................................................................................................................................. 23 Power-up sequence .................................................................................................................................... 26 Operation of the SDRAM ............................................................................................................................ 27 Timing Waveforms ...................................................................................................................................... 43 L Package Drawing........................................................................................................................................ 50 Recommended Soldering Conditions ......................................................................................................... 51 t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 3 EDS1232AATA-MI Electrical Specifications • All voltages are referenced to VSS (GND). • After power up, execute power up sequence and initialization sequence before proper device operation is achieved (refer to the Power up sequence). Absolute Maximum Ratings Symbol Rating Unit Voltage on any pin relative to VSS VT –0.5 to +4.6 V Supply voltage relative to VSS VDD, VDDQ –0.5 to +4.6 V Short circuit output current IOS 50 mA Power dissipation PD 1.0 W Operating ambient temperature TA –40 to +85 °C Storage temperature Tstg –55 to +125 °C EO Parameter Note Caution Exposing the device to stress above those listed in Absolute Maximum Ratings could cause permanent damage. The device is not meant to be operated under conditions outside the limits described in the operational section of this specification. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Recommended DC Operating Conditions (TA = –40 to +85°C) Supply voltage Symbol min. typ. max. Unit VDD, VDDQ 3.0 3.3 3.6 V VSS 0 0 0 L Parameter Notes V Input high voltage VIH 2.0 ⎯ VDD + 0.3* V Input low voltage VIL –0.3*2 ⎯ 0.8 V 1 t uc od Pr Notes: 1. VIH (max.) = VDDQ + 1.5V (pulse width ≤ 5ns). 2. VIL (min.) = –1.5V (pulse width ≤ 5ns). Data Sheet E0340E30 (Ver. 3.0) 4 EDS1232AATA-MI DC Characteristics 1 (TA = –40 to +85°C, VDD, VDDQ = 3.3V±0.3V, VSS, VSSQ = 0V) Parameter /CAS latency Symbol Operating current (CL = 2) max. Unit IDD1 105 mA (CL = 3) IDD1 105 mA Standby current in power down IDD2P 1 mA Standby current in power down (input signal stable) IDD2PS 1 mA Standby current in non power down EO Standby current in non power down (input signal stable) Active standby current in power down Active standby current in power down (input signal stable) Active standby current in non power down Grade Test condition Burst length = 1 tRC ≥ tRC (min.) IO = 0mA One bank active 1 CKE ≤ VIL (max.) tCK = 15ns CKE ≤ VIL (max.) tCK = ∞ IDD2N 20 mA CKE ≥ VIH (min.) tCK = 15ns CS ≥ VIH (min.) Input signals are changed one time during 30ns IDD2NS 8 mA CKE ≥ VIH (min.) tCK = ∞ IDD3P 5 mA CKE ≤ VIL (max.) tCK = 15ns IDD3PS 4 mA CKE ≤ VIL (max.), tCK = ∞ 25 mA CKE ≥ VIH (min.), tCK = 15 ns, /CS ≥ VIH (min.), Input signals are changed one time during 30ns. IDD3N Notes L IDD3NS 15 mA CKE ≥ VIH (min.), tCK = ∞, Burst operating current IDD4 180 mA tCK ≥ tCK (min.), IO = 0mA, All banks active 2 Refresh current IDD5 210 mA tRC ≥ tRC (min.) 3 mA VIH ≥ VDD − 0.2V, VIL ≤ GND + 0.2V Self refresh current Pr Active standby current in non power down (input signal stable) IDD6 0.8 od Notes: 1. IDD1 depends on output loading and cycle rates. Specified values are obtained with the output open. In addition to this, IDD1 is measured condition that addresses are changed only one time during tCK (min.). 2. IDD4 depends on output loading and cycle rates. Specified values are obtained with the output open. In addition to this, IDD4 is measured condition that addresses are changed only one time during tCK (min.). 3. IDD5 is measured on condition that addresses are changed only one time during tCK (min.). DC Characteristics 2 (TA = –40 to +85°C, VDD, VDDQ = 3.3V±0.3V, VSS, VSSQ = 0V) Parameter Symbol min. max. Unit Test condition 1.0 µA 0 = VIN = VDDQ, VDDQ = VDD, All other pins not under test = 0V ILI –1.0 Output leakage current ILO –1.5 1.5 µA 0 = VIN = VDDQ DOUT is disabled Output high voltage VOH 2.4 — V IOH = –2 mA Output low voltage VOL — 0.4 V IOL = 2 mA Data Sheet E0340E30 (Ver. 3.0) 5 t uc Input leakage current Notes EDS1232AATA-MI Pin Capacitance (TA = 25°C, f = 1MHz) Parameter Symbol Input capacitance Data input/output capacitance Pins min. typ. max. Unit CI1 Address 2.5 — 4.0 pF CI2 CLK, CKE, /CS, /RAS, /CAS, /WE, DQM 2.5 — 4.0 pF CI/O DQ 4.0 — 6.5 pF Notes AC Characteristics (TA = –40 to +85°C, VDD, VDDQ = 3.3V±0.3V, VSS, VSSQ = 0V) -75 Symbol min. max. Unit System clock cycle time (CL = 2) tCK 10 — ns EO Parameter (CL = 3) tCK 7.5 — ns CLK high pulse width tCH 2.5 — ns CLK low pulse width tCL 2.5 — ns Access time from CLK tAC — 5.4 ns Data-out hold time tOH 2 — ns CLK to Data-out low impedance tLZ 0 — ns CLK to Data-out high impedance 2 5.4 ns 1.5 — ns tHI 0.8 — ns CKE setup time (Power down exit) tCKSP 1.5 — ns ACT to REF/ACT command period (operation) tRC 67.5 ⎯ ns Input hold time L tHZ tSI Input setup time Pr 67.5 ⎯ ns tRAS 45 120000 ns Active command to column command (same bank) tRCD 20 ⎯ ns Precharge to active command period tRP 20 ⎯ ns Write recovery or data-in to precharge lead time tDPL 15 ⎯ ns Last data into active latency tDAL Active (a) to Active (b) command period tRRD Mode register set cycle time tRSC Transition time (rise and fall) tT Refresh period (4096 refresh cycles) tREF od tRC Active to Precharge command period (refresh) 2CLK + 20ns ⎯ 15 ⎯ Notes ns 2 ⎯ CLK 0.5 30 ns — 64 ms t uc Data Sheet E0340E30 (Ver. 3.0) 6 EDS1232AATA-MI Test Conditions • AC high level input voltage / low level input voltage: 2.4V / 0.4V • Input timing measurement reference level: 1.4V • Transition time (Input rise and fall time): 1ns • Output timing measurement reference level: 1.4V • Termination voltage (Vtt): 1.4V tCK tCH CLK tCL 2.4V 1.4V 0.4V EO tSETUP tHOLD Input 2.4V 1.4V 0.4V tAC tOH Output L Vtt Z = 50 Ω 50 Ω Output Pr 30pF Input Waveforms and Output Load t uc od Data Sheet E0340E30 (Ver. 3.0) 7 EDS1232AATA-MI Relationship Between Frequency and Minimum Latency Parameter -75 Frequency (MHz) 133 100 Symbol 7.5 10 Unit Notes lRCD 3 2 tCK 1 lRC 9 7 tCK 1 lRAS 6 5 tCK 1 lRP 3 2 tCK 1 lDPL 2 2 tCK 1 lRRD 2 2 tCK 1 Self refresh exit time lSREX 1 1 tCK 2 Last data in to active command (Auto precharge, same bank) lDAL 5 4 tCK = [lDPL + lRP] Self refresh exit to command input lSEC 9 7 tCK = [lRC] 3 Precharge command to high impedance (CL = 2) lHZP ⎯ 2 tCK (CL = 3) lHZP 3 3 tCK lAPR 1 1 tCK lEP ⎯ –1 tCK lEP –2 –2 tCK Column command to column command lCCD 1 1 tCK Write command to data in latency lWCD 0 0 tCK lDID 0 0 tCK lDOD 2 2 tCK lCLE 1 1 tCK (ns) L EO Active command to column command (same bank) Active command to active command (same bank) Active command to precharge command (same bank) Precharge command to active command (same bank) Write recovery or data-in to precharge command (same bank) Active command to active command (different bank) Last data out to active command (auto precharge) (same bank) Last data out to precharge (early precharge) (CL = 2) DQM to data in DQM to data out CKE to CLK disable Register set to active command lMRD /CS to command disable lCDD Power down exit to command input lPEC tCK od Pr (CL = 3) 2 2 tCK 0 0 tCK 1 1 tCK Notes: 1. lRCD to lRRD are recommended value. 2. Be valid [DESL] or [NOP] at next command of self refresh exit. 3. Except [DESL] and [NOP] t uc Data Sheet E0340E30 (Ver. 3.0) 8 EDS1232AATA-MI Block Diagram CLK CKE Clock Generator Bank 3 Bank 2 Bank 1 Mode Register Data Control Circuit Input & Output Buffer /WE DQM Column Decoder & Latch Circuit Column Address Buffer & Burst Counter Latch Circuit /CAS Bank 0 Sense Amplifier Control Logic /RAS Command Decoder EO /CS Row Address Buffer & Refresh Counter Row Decoder Address DQ L t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 9 EDS1232AATA-MI Pin Function CLK (input pin) CLK is the master clock input. Other inputs signals are referenced to the CLK rising edge. CKE (input pins) CKE determine validity of the next CLK (clock). If CKE is high, the next CLK rising edge is valid; otherwise it is invalid. If the CLK rising edge is invalid, the internal clock is not issued and the Synchronous DRAM suspends operation. When the Synchronous DRAM is not in burst mode and CKE is negated, the device enters power down mode. During power down mode, CKE must remain low. EO /CS (input pins) /CS low starts the command input cycle. When /CS is high, commands are ignored but operations continue. /RAS, /CAS, and /WE (input pins) /RAS, /CAS and /WE have the same symbols on conventional DRAM but different functions. For details, refer to the command table. L A0 to A11 (input pins) Row Address is determined by A0 to A11 at the CLK (clock) rising edge in the active command cycle. Column Address is determined by A0 to 7 at the CLK rising edge in the read or write command cycle. A10 defines the precharge mode. When A10 is high in the precharge command cycle, all banks are precharged; when A10 is low, only the bank selected by BA0 and BA1 is precharged. When A10 is high in read or write command cycle, the precharge starts automatically after the burst access. [Bank Select Signal Table] Pr BA0 and BA1 (input pin) BA0 and BA1 are bank select signal. (See Bank Select Signal Table) BA0 Bank 0 Bank 1 Bank 2 Remark: H: VIH. L: VIL. L L H L L H H od Bank 3 BA1 H DQ0 to DQ31 (input/output pins) DQ pins have the same function as I/O pins on a conventional DRAM. t uc DQM (input pins) DQM controls I/O buffers. DQM0 controls DQ0 to 7, DQM1 controls DQ8 to DQ15, DQM2 controls DQ16 to DQ23, DQM3 controls DQ24 to DQ31. In read mode, DQM controls the output buffers like a conventional /OE pin. DQM high and DQM low turn the output buffers off and on, respectively. The DQM latency for the read is two clocks. In write mode, DQM controls the word mask. Input data is written to the memory cell if DQM is low but not if DQM is high. The DQM latency for the write is zero. VDD, VSS, VDDQ, VSSQ (Power supply) VDD and VSS are power supply pins for internal circuits. VDDQ and VSSQ are power supply pins for the output buffers. Data Sheet E0340E30 (Ver. 3.0) 10 EDS1232AATA-MI Command Operation Mode register set command (/CS, /RAS, /CAS, /WE) The Synchronous DRAM has a mode register that defines how the device operates. In this command, A0 through A11 are the data input pins. After power on, the mode register set command must be executed to initialize the device. The mode register can be set only when all banks are in idle state. During 2CLK (tRSC) following this command, the Synchronous DRAM cannot accept any other commands. CLK CKE H /CS /RAS /CAS EO /WE BA0, BA1 (Bank select) A10 Add Mode Register Set Command L Activate command (/CS, /RAS = Low, /CAS, /WE = High) The Synchronous DRAM has four banks, each with 4,096 rows. This command activates the bank selected by BA0 and BA1 and a row address selected by A0 through A11. This command corresponds to a conventional DRAM's /RAS falling. CLK CKE H /CS Pr /RAS /CAS /WE BA0, BA1 (Bank select) A10 Row od Add Row Row Address Strobe and Bank Activate Command t uc Data Sheet E0340E30 (Ver. 3.0) 11 EDS1232AATA-MI Precharge command (/CS, /RAS, /WE = Low, /CAS = High) This command begins precharge operation of the bank selected by BA0 and BA1. When A10 is High, all banks are precharged, regardless of BA0 and BA1. When A10 is Low, only the bank selected by BA0 and BA1 is precharged. After this command, the Synchronous DRAM can’t accept the activate command to the precharging bank during tRP (precharge to activate command period). This command corresponds to a conventional DRAM’s /RAS rising. CLK CKE H /CS /RAS /CAS /WE EO BA0, BA1 (Bank select) A10 (Precharge select) Add Precharge Command Write command (/CS, /CAS, /WE = Low, /RAS = High) If the mode register is in the burst write mode, this command sets the burst start address given by the column address to begin the burst write operation. The first write data in burst mode can input with this command with subsequent data on following clocks. L CLK CKE H /CS /RAS Pr /CAS /WE BA0, BA1 (Bank select) A10 Add Col. t uc od Column Address and Write Command Data Sheet E0340E30 (Ver. 3.0) 12 EDS1232AATA-MI Read command (/CS, /CAS = Low, /RAS, /WE = High) Read data is available after /CAS latency requirements have been met. This command sets the burst start address given by the column address. CLK CKE H /CS /RAS /CAS /WE BA0, BA1 (Bank select) EO A10 Add Col. Column Address and and Read Command CBR (auto) refresh command (/CS, /RAS, /CAS = Low, /WE, CKE = High) This command is a request to begin the CBR (auto) refresh operation. The refresh address is generated internally. Before executing CBR (auto) refresh, all banks must be precharged. After this cycle, all banks will be in the idle (precharged) state and ready for a row activate command. During tRC period (from refresh command to refresh or activate command), the Synchronous DRAM cannot accept any other command L CLK CKE H /CS /RAS /CAS Pr /WE BA0, BA1 (Bank select) A10 Add CBR (auto) Refresh Command t uc od Data Sheet E0340E30 (Ver. 3.0) 13 EDS1232AATA-MI Self refresh entry command (/CS, /RAS, /CAS, CKE = Low, /WE = High) After the command execution, self refresh operation continues while CKE remains low. When CKE goes high, the Synchronous DRAM exits the self refresh mode. During self refresh mode, refresh interval and refresh operation are performed internally, so there is no need for external control. Before executing self refresh, all banks must be precharged. CLK CKE /CS /RAS /CAS /WE EO BA0, BA1 (Bank select) A10 Add Self Refresh Entry Command Burst stop command (/CS = /WE = Low, /RAS, /CAS = High) This command can stop the current burst operation. CLK L CKE H /CS /RAS /CAS Pr /WE BA0, BA1 (Bank select) A10 Add Burst Stop Command in Full Page Mode od No operation (/CS = Low, /RAS, /CAS, /WE = High) This command is not an execution command. No operations begin or terminate by this command. CLK CKE H /CS /RAS /WE BA0, BA1 (Bank select) A10 Add No Operation Data Sheet E0340E30 (Ver. 3.0) 14 t uc /CAS EDS1232AATA-MI Truth Table Command Truth Table CKE BA0, A9 - A0, Symbol n–1 n /CS /RAS /CAS /WE BA1 A10 A11 Device deselect DESL H × H × × × × × × No operation NOP H × L H H H × × × Burst stop BST H × L H H L × × × Read READ H × L H L H V L V Read with auto precharge READA H × L H L H V H V Write WRIT H × L H L L V L V Write with auto precharge WRITA H × L H L L V H V EO Function Bank activate ACT H × L L H H V V V Precharge select bank PRE H × L L H L V L × Precharge all banks PALL H × L L H L × H × Mode register set MRS H × L L L L L L V Remark: H: VIH. L: VIL. ×: VIH or VIL, V = Valid data DQM Truth Table L Function CKE DQM 0 1 2 3 n–1 n Data write / output enable ENB H × L L L L Data mask / output disable MASK H × H H H H DQ0 to DQ7 write enable/output enable ENB0 H × L × × × DQ8 to DQ15 write enable/output enable ENB1 H × × L × × DQ16 to DQ23 write enable/output enable ENB2 H × × × L × DQ24 to DQ31 write enable/output enable ENB3 H × × × × L DQ0 to DQ7 write inhibit/output disable MASK0 H × H × × × DQ8 to DQ15 write inhibit/output disable MASK 1 H × × H × × DQ16 to DQ23 write inhibit/output disable MASK 2 H × × × H × DQ24 to DQ31 write inhibit/output disable MASK 3 H × × × × H Remark: H: VIH. L: VIL. ×: VIH or VIL t uc od Pr Symbol Data Sheet E0340E30 (Ver. 3.0) 15 EDS1232AATA-MI CKE Truth Table CKE Current state Function n–1 n /CS /RAS /CAS /WE Address Activating Clock suspend mode entry Symbol H L × × × × × Any Clock suspend mode L L × × × × × Clock suspend Clock suspend mode exit L H × × × × × Idle CBR (auto) refresh command REF H H L L L H × Idle Self refresh entry SELF Self refresh Self refresh exit Idle Power down entry EO Power down Power down exit H L L L L H × L H L H H H × L H H × × × × H L L H H H × H L H × × × × L H H × × × × L H L H H H × Remark: H: VIH. L: VIL. ×: VIH or VIL L t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 16 EDS1232AATA-MI 1 Function Truth Table* Current state /CS Idle Command Operation Notes H × × × × L H H × × DESL Nop or power down 2 NOP or BST Nop or power down 2 L H L H BA, CA, A10 READ/READA ILLEGAL 3 L H L L BA, CA, A10 WRIT/ WRITA ILLEGAL 3 L L H H L L H L BA, RA ACT Row activating BA, A10 PRE/PALL Nop L L L H × REF/SELF CBR (auto) refresh or self refresh L L L L OPCODE MRS Mode register accessing H × L H × × × DESL Nop H × × NOP or BST Nop L H L H BA, CA, A10 READ/READA Begin read: Determine AP 5 L H L L BA, CA, A10 WRIT/ WRITA Begin write: Determine AP 5 L L H H BA, RA ACT ILLEGAL 3 L L H L BA, A10 PRE/PALL Precharge 6 L L L H × REF/SELF ILLEGAL L L L L OPCODE MRS ILLEGAL Read H × × × × DESL Continue burst to end → Row active L H H H × NOP Continue burst to end → Row active L H H L × BST Burst stop → Row active L H L H BA, CA, A10 READ/READA Terminate burst, new read: Determine AP L H L L L H L L H L L L L L × × L H L 7 L BA, CA, A10 WRIT/WRITA Terminate burst, begin write: Determine AP 7, 8 BA, RA ACT ILLEGAL L BA, A10 PRE/PALL Terminate burst, Precharging H × REF/SELF ILLEGAL 3 L OPCODE MRS ILLEGAL × × DESL Continue burst to end → Write recovering H H × H H L × od L H 4 H Pr Write L EO Row active /RAS /CAS /WE Address H L H BA, CA, A10 H L L BA, CA, A10 L L H H BA, RA L L H L BA, A10 L L L H × L L L L OPCODE Continue burst to end → Write recovering BST Burst stop → Row active READ/READA Terminate burst, start read : Determine AP 7, 8 WRIT/WRITA Terminate burst, new write : Determine AP 7 ACT ILLEGAL 3 PRE/PALL Terminate burst, Precharging 9 REF/SELF ILLEGAL MRS ILLEGAL Data Sheet E0340E30 (Ver. 3.0) 17 t uc L L NOP EDS1232AATA-MI Current state /CS /RAS /CAS /WE Address Command Operation Read with auto H × × × × DESL Continue burst to end → Precharging precharge L H H H × NOP Continue burst to end → Precharging L H H L × BST ILLEGAL L H L H BA, CA, A10 READ/READA ILLEGAL 3 L H L L BA, CA, A10 WRIT/ WRITA ILLEGAL 3 L L H H BA, RA ACT ILLEGAL 3 3 L L H L BA, A10 PRE/PALL ILLEGAL L L L H × REF/SELF ILLEGAL L L L L OPCODE MRS ILLEGAL EO Write with auto precharge H × × × × DESL Continue burst to end → Write recovering with auto precharge L H H H × NOP Continue burst to end → Write recovering with auto precharge L H H L × BST ILLEGAL L H L H BA, CA, A10 READ/READA ILLEGAL 3 L H L L BA, CA, A10 WRIT/ WRITA ILLEGAL 3 L L H H BA, RA ACT ILLEGAL 3 3 L L H L BA, A10 PRE/PALL ILLEGAL L L L H × REF/SELF ILLEGAL L L L L OPCODE MRS ILLEGAL H × × × × DESL Nop → Enter idle after tRP L H H H × NOP Nop → Enter idle after tRP L H H L × BST ILLEGAL L H L H BA, CA, A10 READ/READA ILLEGAL 3 L H L L BA, CA, A10 WRIT/WRITA ILLEGAL 3 L L H H BA, RA ACT ILLEGAL 3 L L H L BA, A10 PRE/PALL Nop → Enter idle after tRP L L L H × L L L L OPCODE H × × × × L H H H × Pr Row activating L od Precharging Notes REF/SELF ILLEGAL MRS ILLEGAL DESL Nop → Enter bank active after tRCD NOP Nop → Enter bank active after tRCD BST ILLEGAL READ/READA ILLEGAL H H L × H L H BA, CA, A10 L H L L BA, CA, A10 WRIT/WRITA ILLEGAL L L H H BA, RA ACT ILLEGAL L L H L BA, A10 PRE/PALL ILLEGAL L L L H × REF/SELF ILLEGAL L L L L OPCODE MRS ILLEGAL Data Sheet E0340E30 (Ver. 3.0) 18 3 t uc L L 3 3, 10 3 EDS1232AATA-MI Current state /CS /RAS /CAS /WE Address Command Operation Write recovering H × × × × DESL Nop → Enter row active after tDPL L H H H × NOP Nop → Enter row active after tDPL Notes L H H L × BST Nop → Enter row active after tDPL L H L H BA, CA, A10 READ/READA Start read, Determine AP L H L L BA, CA, A10 WRIT/ WRITA New write, Determine AP L L H H BA, RA ACT ILLEGAL 3 3 L L H L BA, A10 PRE/PALL ILLEGAL L L L H × REF/SELF ILLEGAL L L L L OPCODE MRS ILLEGAL 8 H × × × × DESL Nop → Enter precharge after tDPL with auto L H H H × NOP Nop → Enter precharge after tDPL precharge L H H L × BST Nop → Enter row active after tDPL L H L H BA, CA, A10 READ/READA ILLEGAL L H L L BA, CA, A10 WRIT/WRITA ILLEGAL 3, 8 L L H H BA, RA ACT ILLEGAL 3 L L H L BA, A10 PRE/PALL ILLEGAL 3 L L L H × REF/SELF ILLEGAL L L L L OPCODE MRS ILLEGAL Refresh L EO Write recovering × × × × DESL Nop → Enter idle after tRC L H H H × NOP/BST Nop → Enter idle after tRC L H H L × READ/READA ILLEGAL L H L H × ACT/PRE/PALL ILLEGAL H L H × × accessing L H H L H H L H L L L L L × REF/SELF/MRS ILLEGAL × × DESL Nop → Enter idle after tRSC H × NOP Nop → Enter idle after tRSC L × BST ILLEGAL H × READ/READA ILLEGAL L × od L Mode register Pr H ACT/PRE/PLL/ ILLEGAL REF/SELF/MRS Remark: H: VIH. L: VIL. ×: VIH or VIL, V = Valid data BA: Bank Address, CA: Column Address, RA: Row Address t uc Notes: 1. All entries assume that CKE was active (High level) during the preceding clock cycle. 2. If all banks are idle, and CKE is inactive (Low level), the Synchronous DRAM will enter Power down mode. 3. Illegal to bank in specified states; Function may be legal in the bank indicated by Bank Address (BA), depending on the state of that bank. 4. If all banks are idle, and CKE is inactive (Low level), the Synchronous DRAM will enter Self refresh mode. All input buffers except CKE will be disabled. 5. Illegal if tRCD is not satisfied. 6. Illegal if tRAS is not satisfied. 7. Must satisfy burst interrupt condition. 8. Must satisfy bus contention, bus trun around, and/or write recovery requirements. 9. Must mask preceding data which don’t satisfy tDPL. 10. Illegal if tRRD is not satisfied. Data Sheet E0340E30 (Ver. 3.0) 19 EDS1232AATA-MI Command Truth Table for CKE CKE Current State n–1 n Self refresh Self refresh recovery Operation Notes H × × × × × × INVALID, CLK (n – 1) would exit self refresh H H × × × × Self refresh recovery L H L H H × × Self refresh recovery L H L H L × × ILLEGAL L H L L × × × ILLEGAL L L × × × × × Continue self refresh H H H × × × × Idle after tRC H H L H H × × Idle after tRC H H L H L × × ILLEGAL H H L L × × × ILLEGAL H L H × × × × ILLEGAL H L L H H × × ILLEGAL H L L H L × × ILLEGAL × H L L L × × H × × × × × L H H × × × L H L H H H × EXIT power down L L × × × × × Continue power down mode L All banks idle /RAS /CAS /WE Address L EO Power down /CS ILLEGAL INVALID, CLK (n – 1) would exit power down × EXIT power down H H H × × × Refer to operations in Function Truth Table H H L H × × Refer to operations in Function Truth Table H H L Refer to operations in Function Truth Table H × Pr L H H L L L H × H H L L L L OPCODE Refer to operations in Function Truth Table H L H × × × Begin power down next cycle H L L H × × Refer to operations in Function Truth Table H L L L H × Refer to operations in Function Truth Table L L L L H L L L L L L H × × × × od H H CBR (auto) Refresh × Self refresh × Exit power down next cycle L L × × × × H × × × × × L × × × × × Any state other than H H × × × × listed above H L × × × × × Begin clock suspend next cycle L H × × × × × Exit clock suspend next cycle L L × × × × × Maintain clock suspend Row active 1 OPCODE Refer to operations in Function Truth Table × Power down × Refer to operations in Function Truth Table × Clock suspend 1 1 t uc Refer to operations in Function Truth Table 2 Remark: H = VIH, L = VIL, × = VIH or VIL Notes: 1. Self refresh can be entered only from the all banks idle state. Power down can be entered only from all banks idle or row active state. 2. Must be legal command as defined in Function Truth Table. Data Sheet E0340E30 (Ver. 3.0) 20 EDS1232AATA-MI Simplified State Diagram Self Refresh SE LF SE LF MRS Mode Register Set exi t REF IDLE CBR(auto) Refresh CK E ACT CKE ROW ACTIVE e ite wit pre h ch arg Wr Au CKE Read T ad WRITE Write Precharge CKE CKE READA CKE READ SUSPEND READA SUSPEND od POWER ON PR E( Pre cha rge ter min atio n) CKE n) atio min ter rge cha Pre E( PR WRITEA CKE READ CKE CKE Read h wit ad arge h Re c pre to PRE W Re Au e rit Write BS T to BS Active Power Down CKE Pr WRITEA SUSPEND E Power Down L EO WRITE SUSPEND CK Precharge t uc Automatic sequence Manual input Data Sheet E0340E30 (Ver. 3.0) 21 EDS1232AATA-MI Programming Mode Registers The mode register is programmed by the Mode register set command using address bits A11 through A0, BA0 and BA1 as data inputs. The registers retain data until it is re-programmed, or the device loses power. The mode register has three fields; Options /CAS latency Wrap type Burst length : : : : A11 through A7, BA0, BA1 A6 through A4 A3 A2 through A0 Following mode register programming, no command can be issued before at least 2 CLK have elapsed. EO /CAS Latency /CAS latency is the most critical of the parameters being set. It tells the device how many clocks must elapse before the data will be available. The value is determined by the frequency of the clock and the speed grade of the device. ”Relationship between Frequency and Latency” shows the relationship of /CAS latency to the clock period and the speed grade of the device. L Burst Length Burst Length is the number of words that will be output or input in a read or write cycle. After a read burst is completed, the output bus will become High-Z. The burst length is programmable as 1, 2, 4, 8 or full page. t uc od Pr Wrap Type (Burst Sequence) The wrap type specifies the order in which the burst data will be addressed. This order is programmable as either “Sequential” or “Interleave”. The method chosen will depend on the type of CPU in the system. Some microprocessor cache systems are optimized for sequential addressing and others for interleaved addressing. “Burst Length Sequence” shows the addressing sequence for each burst length using them. Both sequences support bursts of 1, 2, 4 and 8. Additionally, sequence supports the full page length. Data Sheet E0340E30 (Ver. 3.0) 22 EDS1232AATA-MI Mode Register BA0 BA1 A11 0 0 0 BA0 BA1 A11 x x x BA0 BA1 A11 BA0 BA1 A11 x x x BA0 BA1 A11 0 0 A9 A8 A7 0 0 0 1 A10 A9 A8 A7 x 1 0 0 A10 A9 A8 A7 1 0 A6 A5 A4 A3 A2 A1 A0 JEDEC Standard Test Set (refresh counter test) A6 A5 A4 LTMODE A6 A5 A3 A2 WT A4 A3 A1 A0 BL A2 A1 Burst Read and Single Write (for Write Through Cache) A0 Use in future A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 x x 1 1 V V V V V V V A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 0 0 0 0 LTMODE WT Vender Specific V = Valid x = Don’t care BL L EO 0 A10 Mode Register Set Burst length Bits2-0 000 001 010 011 100 101 110 111 Wrap type 0 1 WT = 1 1 2 4 8 R R R R Sequential Interleave Bits6-4 000 001 010 011 100 101 110 111 /CAS latency R R 2 3 R R R R Remark R : Reserved od Pr Latency mode WT = 0 1 2 4 8 R R R Full page Mode Register Set Timing CLK CKE /CS t uc /RAS /CAS /WE A0 - A11, BA0, BA1 Mode Register Set Data Sheet E0340E30 (Ver. 3.0) 23 EDS1232AATA-MI Burst Length and Sequence [Burst of Two] Starting address (column address A0, binary) Sequential addressing sequence (decimal) Interleave addressing sequence (decimal) 0 0, 1 0, 1 1 1, 0 1, 0 Starting address (column address A1 to A0, binary) Sequential addressing sequence (decimal) Interleave addressing sequence (decimal) 00 0, 1, 2, 3 0, 1, 2, 3 01 1, 2, 3, 0 1, 0, 3, 2 10 2, 3, 0, 1 2, 3, 0, 1 11 3, 0, 1, 2 3, 2, 1, 0 Sequential addressing sequence (decimal) Interleave addressing sequence (decimal) [Burst of Four] EO [Burst of Eight] Starting address (column address A2 to A0, binary) 001 010 011 L 000 100 110 111 0, 1, 2, 3, 4, 5, 6, 7 1, 2, 3, 4, 5, 6, 7, 0 1, 0, 3, 2, 5, 4, 7, 6 2, 3, 4, 5, 6, 7, 0, 1 2, 3, 0, 1, 6, 7, 4, 5 3, 4, 5, 6, 7, 0, 1, 2 3, 2, 1, 0, 7, 6, 5, 4 4, 5, 6, 7, 0, 1, 2, 3 4, 5, 6, 7, 0, 1, 2, 3 Pr 101 0, 1, 2, 3, 4, 5, 6, 7 5, 6, 7, 0, 1, 2, 3, 4 5, 4, 7, 6, 1, 0, 3, 2 6, 7, 0, 1, 2, 3, 4, 5 6, 7, 4, 5, 2, 3, 0, 1 7, 0, 1, 2, 3, 4, 5, 6 7, 6, 5, 4, 3, 2, 1, 0 Full page burst is an extension of the above tables of sequential addressing, with the length being 256. t uc od Data Sheet E0340E30 (Ver. 3.0) 24 EDS1232AATA-MI Address Bits of Bank-Select and Precharge Row A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 BA1 BA0 (Activate command) A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 EO (/CAS strobes) A1 A2 A3 Result Select Bank 0 “Activate” command Select Bank 1 “Activate” command 0 0 0 1 1 0 Select Bank 2 “Activate” command 1 1 Select Bank 3 “Activate” command A10 0 0 0 0 1 BA1 0 0 1 1 x BA0 0 1 0 1 x Result Precharge Bank 0 Precharge Bank 1 Precharge Bank 2 Precharge Bank 3 Precharge All Banks x : Don’t care 0 A4 A5 A6 L A0 BA0 BA1 BA0 (Precharge command) Col. BA1 A7 A8 A9 A10 x BA1 BA0 1 BA1 disables Auto-Precharge (End of Burst) enables Auto-Precharge (End of Burst) BA0 Result 0 0 0 1 1 0 enables Read/Write commands for Bank 2 1 1 enables Read/Write commands for Bank 3 t uc od Pr enables Read/Write commands for Bank 0 enables Read/Write commands for Bank 1 Data Sheet E0340E30 (Ver. 3.0) 25 EDS1232AATA-MI Power-up sequence Power-up sequence The SDRAM should be goes on the following sequence with power up. The CLK, CKE, /CS, DQM and DQ pins keep low till power stabilizes. The CLK pin is stabilized within 100 µs after power stabilizes before the following initialization sequence. The CKE and DQM is driven to high between power stabilizes and the initialization sequence. This SDRAM has VDD clamp diodes for CLK, CKE, address, /RAS, /CAS, /WE, /CS, DQM and DQ pins. If these pins go high before power up, the large current flows from these pins to VDD through the diodes. Initialization sequence EO When 200 µs or more has past after the above power-up sequence, all banks must be precharged using the precharge command (PALL). After tRP delay, set 8 or more auto refresh commands (REF). Set the mode register set command (MRS) to initialize the mode register. We recommend that by keeping DQM and CKE to High, the output buffer becomes High-Z during Initialization sequence, to avoid DQ bus contention on memory system formed with a number of device. 100 μs 200 μs 0V L VDD, VDDQ Initialization sequence Power up sequence Low CLK Low /CS, DQ Low Pr CKE, DQM Power stabilize Power-up sequence and Initialization sequence t uc od Data Sheet E0340E30 (Ver. 3.0) 26 EDS1232AATA-MI Operation of the SDRAM Read/Write Operations Bank active Before executing a read or write operation, the corresponding bank and the row address must be activated by the bank active (ACT) command. An interval of tRCD is required between the bank active command input and the following read/write command input. EO Read operation A read operation starts when a read command is input. Output buffer becomes Low-Z in the (/CAS Latency - 1) cycle after read command set. The SDRAM can perform a burst read operation. The burst length can be set to 1, 2, 4 and 8. The start address for a burst read is specified by the column address and the bank select address at the read command set cycle. In a read operation, data output starts after the number of clocks specified by the /CAS Latency. The /CAS Latency can be set to 2 or 3. When the burst length is 1, 2, 4 and 8 the DOUT buffer automatically becomes High-Z at the next clock after the successive burst-length data has been output. The /CAS latency and burst length must be specified at the mode register. CLK Command DQ READ ACT L Address tRCD Row Column out 0 CL = 2 CL = 3 out 1 out 2 out 3 out 0 out 1 out 2 out 3 Pr CL = /CAS latency Burst Length = 4 /CAS Latency CLK tRCD ACT READ Address Row Column BL = 1 out 0 out 0 out 1 DQ BL = 2 od Command out 0 out 1 out 2 out 3 BL = 4 out 3 out 4 out 5 out 6 out 7 t uc out 0 out 1 out 2 BL = 8 BL : Burst Length /CAS Latency = 2 Burst Length Data Sheet E0340E30 (Ver. 3.0) 27 EDS1232AATA-MI Write operation Burst write or single write mode is selected by the OPCODE of the mode register. 1. Burst write: A burst write operation is enabled by setting OPCODE (A9, A8) to (0, 0). A burst write starts in the same clock as a write command set. (The latency of data input is 0 clock.) The burst length can be set to 1, 2, 4 and 8, like burst read operations. The write start address is specified by the column address and the bank select address at the write command set cycle. CLK tRCD Command ACT WRIT Address Row Column in 0 EO BL = 1 DQ in 0 in 1 in 0 in 1 in 2 in 3 in 0 in 1 in 2 in 3 BL = 2 BL = 4 in 4 in 5 in 6 in 7 BL = 8 CL = 2, 3 Burst write L 2. Single write: A single write operation is enabled by setting OPCODE (A9, A8) to (1, 0). In a single write operation, data is only written to the column address and the bank select address specified by the write command set cycle without regard to the burst length setting. (The latency of data input is 0 clock). CLK Command DQ WRIT Pr Address ACT tRCD Row Column in 0 Single write t uc od Data Sheet E0340E30 (Ver. 3.0) 28 EDS1232AATA-MI Auto Precharge Read with auto-precharge In this operation, since precharge is automatically performed after completing a read operation, a precharge command need not be executed after each read operation. The command executed for the same bank after the execution of this command must be the bank active (ACT) command. In addition, an interval defined by lAPR is required before execution of the next command. [Clock cycle time] /CAS latency Precharge start cycle 3 2 cycle before the final data is output 2 1 cycle before the final data is output EO CLK CL=2 Command ACT READA ACT lRAS DQ CL=3 Command out0 out1 out2 out3 lAPR ACT READA ACT lRAS DQ out0 out1 L Note: Internal auto-precharge starts at the timing indicated by " ". And an interval of tRAS (lRAS) is required between previous active (ACT) command and internal precharge " out2 out3 lAPR ". Burst Read (BL = 4) CLK ACT WRITA od Command Pr Write with auto-precharge In this operation, since precharge is automatically performed after completing a burst write or single write operation, a precharge command need not be executed after each write operation. The command executed for the same bank after the execution of this command must be the bank active (ACT) command. In addition, an interval of lDAL is required between the final valid data input and input of next command. ACT lRAS DQ in0 in1 in2 in3 lDAL Burst Write (BL = 4) Data Sheet E0340E30 (Ver. 3.0) 29 t uc Note: Internal auto-precharge starts at the timing indicated by " ". and an interval of tRAS (lRAS) is required between previous active (ACT) command and internal precharge " ". EDS1232AATA-MI CLK Command ACT ACT WRITA lRAS DQ in lDAL EO Note: Internal auto-precharge starts at the timing indicated by " ". and an interval of tRAS (lRAS) is required between previous active (ACT) command and internal precharge " ". Single Write L t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 30 EDS1232AATA-MI Burst Stop Command During a read cycle, when the burst stop command is issued, the burst read data are terminated and the data bus goes to High-Z after the /CAS latency from the burst stop command. CLK READ Command BST DQ (CL = 2) out DQ (CL = 3) out out out out High-Z out High-Z EO Burst Stop at Read During a write cycle, when the burst stop command is issued, the burst write data are terminated and data bus goes to High-Z at the same clock with the burst stop command. CLK Command BST High-Z in L DQ WRITE in in in Burst Stop at Write t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 31 EDS1232AATA-MI Command Intervals Read command to Read command interval 1. Same bank, same ROW address: When another read command is executed at the same ROW address of the same bank as the preceding read command execution, the second read can be performed after an interval of no less than 1 clock. Even when the first command is a burst read that is not yet finished, the data read by the second command will be valid. CLK Command ACT Address Row READ READ Column A Column B BS EO DQ Bank0 Active out A0 out B0 out B1 out B2 out B3 CL = 3 BL = 4 Bank 0 Column =A Column =B Column =A Column =B Dout Read Read Dout READ to READ Command Interval (same ROW address in same bank) L 2. Same bank, different ROW address: When the ROW address changes on same bank, consecutive read commands cannot be executed; it is necessary to separate the two read commands with a precharge command and a bank active command. 3. Different bank: When the bank changes, the second read can be performed after an interval of no less than 1 clock, provided that the other bank is in the bank active state. Even when the first command is a burst read that is not yet finished, the data read by the second command will be valid. CLK Command ACT READ READ Row 0 Row 1 Column A Column B BS DQ Pr Address ACT out A0 out B0 out B1 out B2 out B3 Bank0 Active Bank3 Bank0 Bank3 Active Read Read CL = 3 BL = 4 Bank0 Bank3 Dout Dout READ to READ Command Interval (different bank) t uc od Data Sheet E0340E30 (Ver. 3.0) 32 EDS1232AATA-MI Write command to Write command interval 1. Same bank, same ROW address: When another write command is executed at the same ROW address of the same bank as the preceding write command, the second write can be performed after an interval of no less than 1 clock. In the case of burst writes, the second write command has priority. CLK Command ACT Address Row WRIT WRIT Column A Column B BS DQ in A0 EO Bank0 Active in B0 in B1 in B2 in B3 Burst Write Mode BL = 4 Bank 0 Column =A Column =B Write Write WRITE to WRITE Command Interval (same ROW address in same bank) L 2. Same bank, different ROW address: When the ROW address changes, consecutive write commands cannot be executed; it is necessary to separate the two write commands with a precharge command and a bank active command. 3. Different bank: When the bank changes, the second write can be performed after an interval of no less than 1 clock, provided that the other bank is in the bank active state. In the case of burst write, the second write command has priority. CLK Command Row 0 BS DQ ACT WRIT Row 1 Column A Column B in A0 Bank0 Active WRIT Pr Address ACT in B0 in B1 in B2 in B3 Burst Write Mode BL = 4 Bank3 Bank0 Bank3 Active Write Write od WRITE to WRITE Command Interval (different bank) t uc Data Sheet E0340E30 (Ver. 3.0) 33 EDS1232AATA-MI Read command to Write command interval 1. Same bank, same ROW address: When the write command is executed at the same ROW address of the same bank as the preceding read command, the write command can be performed after an interval of no less than 1 clock. However, DQM must be set High so that the output buffer becomes High-Z before data input. CLK Command READ WRIT CL=2 DQM CL=3 in B0 DQ (input) in B1 in B2 in B3 EO BL = 4 Burst write High-Z DQ (output) READ to WRITE Command Interval (1) CLK Command READ WRIT L DQM CL=2 2 clock out out out in in in in out out in in in in DQ CL=3 Pr READ to WRITE Command Interval (2) t uc od 2. Same bank, different ROW address: When the ROW address changes, consecutive write commands cannot be executed; it is necessary to separate the two commands with a precharge command and a bank active command. 3. Different bank: When the bank changes, the write command can be performed after an interval of no less than 1 cycle, provided that the other bank is in the bank active state. However, DQM must be set High so that the output buffer becomes High-Z before data input. Data Sheet E0340E30 (Ver. 3.0) 34 EDS1232AATA-MI Write command to Read command interval: 1. Same bank, same ROW address: When the read command is executed at the same ROW address of the same bank as the preceding write command, the read command can be performed after an interval of no less than 1 clock. However, in the case of a burst write, data will continue to be written until one clock before the read command is executed. CLK Command WRIT READ DQM DQ (input) in A0 EO DQ (output) out B0 Column = A Write Column = B Read out B1 out B2 out B3 Burst Write Mode CL = 2 BL = 4 Bank 0 /CAS Latency Column = B Dout WRITE to READ Command Interval (1) CLK DQM DQ (input) L Command in A0 READ in A1 out B0 Pr DQ (output) WRIT Column = A Write out B1 out B2 /CAS Latency Column = B Read Column = B Dout out B3 Burst Write Mode CL = 2 BL = 4 Bank 0 WRITE to READ Command Interval (2) t uc od 2. Same bank, different ROW address: When the ROW address changes, consecutive read commands cannot be executed; it is necessary to separate the two commands with a precharge command and a bank active command. 3. Different bank: When the bank changes, the read command can be performed after an interval of no less than 1 clock, provided that the other bank is in the bank active state. However, in the case of a burst write, data will continue to be written until one clock before the read command is executed (as in the case of the same bank and the same address). Data Sheet E0340E30 (Ver. 3.0) 35 EDS1232AATA-MI Read with auto precharge to Read command interval 1. Different bank: When some banks are in the active state, the second read command (another bank) is executed. Even when the first read with auto-precharge is a burst read that is not yet finished, the data read by the second command is valid. The internal auto-precharge of one bank starts at the next clock of the second command. CLK Command READA READ BS DQ out A0 bank0 Read A out A1 out B0 out B1 bank3 Read EO Note: Internal auto-precharge starts at the timing indicated by " CL= 3 BL = 4 ". Read with Auto Precharge to Read Command Interval (Different bank) 2. Same bank: The consecutive read command (the same bank) is illegal. Write with auto precharge to Write command interval 1. Different bank: When some banks are in the active state, the second write command (another bank) is executed. In the case of burst writes, the second write command has priority. The internal auto-precharge of one bank starts 2 clocks later from the second command. L CLK Command WRITA WRIT BS DQ in A0 in A1 in B0 in B1 in B2 Pr bank0 Write A in B3 bank3 Write Note: Internal auto-precharge starts at the timing indicated by " BL= 4 ". Write with Auto Precharge to Write Command Interval (Different bank) 2. Same bank: The consecutive write command (the same bank) is illegal. t uc od Data Sheet E0340E30 (Ver. 3.0) 36 EDS1232AATA-MI Read with auto precharge to Write command interval 1. Different bank: When some banks are in the active state, the second write command (another bank) is executed. However, DQM must be set High so that the output buffer becomes High-Z before data input. The internal autoprecharge of one bank starts at the next clock of the second command. CLK Command READA WRIT BS CL = 2 DQM CL = 3 DQ (input) EO in B0 DQ (output) in B1 in B2 in B3 High-Z bank0 ReadA BL = 4 bank3 Write Note: Internal auto-precharge starts at the timing indicated by " ". Read with Auto Precharge to Write Command Interval (Different bank) L 2. Same bank: The consecutive write command from read with auto precharge (the same bank) is illegal. It is necessary to separate the two commands with a bank active command. Write with auto precharge to Read command interval 1. Different bank: When some banks are in the active state, the second read command (another bank) is executed. However, in case of a burst write, data will continue to be written until one clock before the read command is executed. The internal auto-precharge of one bank starts at 2 clocks later from the second command. Pr CLK Command WRITA BS DQ (input) in A0 DQ (output) od DQM READ out B0 bank0 WriteA bank3 Read out B1 out B2 out B3 ". t uc Note: Internal auto-precharge starts at the timing indicated by " CL = 3 BL = 4 Write with Auto Precharge to Read Command Interval (Different bank) 2. Same bank: The consecutive read command from write with auto precharge (the same bank) is illegal. It is necessary to separate the two commands with a bank active command. Data Sheet E0340E30 (Ver. 3.0) 37 EDS1232AATA-MI Read command to Precharge command interval (same bank) When the precharge command is executed for the same bank as the read command that preceded it, the minimum interval between the two commands is one clock. However, since the output buffer then becomes High-Z after the clocks defined by lHZP, there is a case of interruption to burst read data output will be interrupted, if the precharge command is input during burst read. To read all data by burst read, the clocks defined by lEP must be assured as an interval from the final data output to precharge command execution. CLK PRE/PALL READ Command DQ out A0 out A1 EO CL=2 out A2 out A3 lEP = -1 cycle READ to PRECHARGE Command Interval (same bank): To output all data (CL = 2, BL = 4) CLK Command PRE/PALL READ DQ out A0 out A1 L CL=3 out A2 out A3 lEP = -2 cycle READ to PRECHARGE Command Interval (same bank): To output all data (CL = 3, BL = 4) CLK READ Pr Command PRE/PALL High-Z DQ out A0 lHZP = 2 CLK Command READ PRE/PALL od READ to PRECHARGE Command Interval (same bank): To stop output data (CL = 2, BL = 1, 2, 4, 8) High-Z DQ out A0 t uc lHZP =3 READ to PRECHARGE Command Interval (same bank): To stop output data (CL = 3, BL = 1, 2, 4, 8) Data Sheet E0340E30 (Ver. 3.0) 38 EDS1232AATA-MI Write command to Precharge command interval (same bank) When the precharge command is executed for the same bank as the write command that preceded it, the minimum interval between the two commands is 1 clock. However, if the burst write operation is unfinished, the input data must be masked by means of DQM for assurance of the clock defined by tDPL. CLK PRE/PALL WRIT Command DQM DQ in A0 in A1 in A2 EO tDPL WRITE to PRECHARGE Command Interval (same bank) (BL = 4 (To stop write operation)) CLK Command PRE/PALL WRIT DQM L DQ in A0 in A1 in A2 in A3 tDPL WRITE to PRECHARGE Command Interval (same bank) (BL = 4 (To write all data)) t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 39 EDS1232AATA-MI Bank active command interval 1. Same bank: The interval between the two bank active commands must be no less than tRC. 2. In the case of different bank active commands: The interval between the two bank active commands must be no less than tRRD. CLK Command ACT ACT Address ROW ROW BS EO tRC Bank 0 Active Bank 0 Active Bank Active to Bank Active for Same Bank CLK ACT Command ACT L Address ROW:0 ROW:1 BS tRRD Bank 3 Active Pr Bank 0 Active Bank Active to Bank Active for Different Bank Mode register set to Bank active command interval The interval between setting the mode register and executing a bank active command must be no less than lMRD. Command Address MRS OPCODE od CLK ACT BS & ROW lMRD Bank Active t uc Mode Register Set Mode register set to Bank active command interval Data Sheet E0340E30 (Ver. 3.0) 40 EDS1232AATA-MI DQM Control The DQM mask the DQ data. The UDQM and LDQM mask the upper and lower bytes of the DQ data, respectively. The timing of UDQM/LDQM is different during reading and writing. Reading When data is read, the output buffer can be controlled by DQM. By setting DQM to Low, the output buffer becomes Low-Z, enabling data output. By setting DQM to High, the output buffer becomes High-Z, and the corresponding data is not output. However, internal reading operations continue. The latency of DQM during reading is 2 clocks. Writing Input data can be masked by DQM. By setting DQM to Low, data can be written. In addition, when DQM is set to High, the corresponding data is not written, and the previous data is held. The latency of DQM during writing is 0 clock. EO CLK DQM High-Z DQ out 0 out 1 out 3 lDOD = 2 Latency L Reading CLK DQ Pr DQM in 0 in 3 in 1 od lDID = 0 Latency Writing t uc Data Sheet E0340E30 (Ver. 3.0) 41 EDS1232AATA-MI Refresh Auto-refresh All the banks must be precharged before executing an auto-refresh command. Since the auto-refresh command updates the internal counter every time it is executed and determines the banks and the ROW addresses to be refreshed, external address specification is not required. The refresh cycles are required to refresh all the ROW addresses within tREF (max.). The output buffer becomes High-Z after auto-refresh start. In addition, since a precharge has been completed by an internal operation after the auto-refresh, an additional precharge operation by the precharge command is not required. EO Self-refresh After executing a self-refresh command, the self-refresh operation continues while CKE is held Low. During selfrefresh operation, all ROW addresses are refreshed by the internal refresh timer. A self-refresh is terminated by a self-refresh exit command. Before and after self-refresh mode, execute auto-refresh to all refresh addresses in or within tREF (max.) period on the condition 1 and 2 below. 1. Enter self-refresh mode within time as below* after either burst refresh or distributed refresh at equal interval to all refresh addresses are completed. 2. Start burst refresh or distributed refresh at equal interval to all refresh addresses within time as below*after exiting from self-refresh mode. Note: tREF (max.) / refresh cycles. Others L Power-down mode The SDRAM enters power-down mode when CKE goes Low in the IDLE state. In power down mode, power consumption is suppressed by deactivating the input initial circuit. Power down mode continues while CKE is held Low. In addition, by setting CKE to High, the SDRAM exits from the power down mode, and command input is enabled from the next clock. In this mode, internal refresh is not performed. t uc od Pr Clock suspend mode By driving CKE to Low during a bank active or read/write operation, the SDRAM enters clock suspend mode. During clock suspend mode, external input signals are ignored and the internal state is maintained. When CKE is driven High, the SDRAM terminates clock suspend mode, and command input is enabled from the next clock. For details, refer to the "CKE Truth Table". Data Sheet E0340E30 (Ver. 3.0) 42 EDS1232AATA-MI Timing Waveforms Read Cycle tCK tCH t CL CLK t RC VIH CKE t RP tRAS tRCD tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI /CS tSI tHI tSI tHI /RAS EO tSI tHI tSI tHI /CAS tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI /WE tSI tHI BS tSI tHI tSI tHI A10 Address tSI tHI tSI tHI L tSI tHI tSI DQM Pr DQ (input) tHI tAC DQ (output) tAC tAC tHZ t AC tOH tOH Bank 0 Active Bank 0 Read tLZ tOH tOH /CAS latency = 2 Burst length = 4 Bank 0 access = VIH or VIL = VOH or VOL Bank 0 Precharge t uc od Data Sheet E0340E30 (Ver. 3.0) 43 EDS1232AATA-MI Write Cycle tCK tCH tCL CLK tRC VIH CKE tRP tRAS tRCD tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI /CS tSI tHI tSI tHI /RAS tSI tHI tSI tHI EO /CAS tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI tSI tHI /WE tSI tHI tSI tHI BS tSI tHI tSI tHI A10 tSI tHI tSI tHI tSI tHI Address L tSI DQM tSI DQ (input) tHI t HI tSI tHI tSI tHI tSI tHI tDPL Pr DQ (output) Bank 0 Write Bank 0 Active Mode Register Set Cycle 1 2 3 4 5 CKE VIH /CS /RAS /CAS /WE 6 7 8 9 10 11 code valid DQM DQ (output) b High-Z DQ (input) lMRD lRP Precharge If needed Mode register Set Bank 3 Active lRCD Output mask Bank 3 Read Data Sheet E0340E30 (Ver. 3.0) 44 13 14 15 16 17 18 19 C: b’ C: b R: b 12 t uc BS Address CL = 2 BL = 4 Bank 0 access = VIH or VIL od 0 CLK Bank 0 Precharge b+3 b’ b’+1 b’+2 b’+3 lRCD = 3 /CAS latency = 3 Burst length = 4 = VIH or VIL EDS1232AATA-MI Read Cycle/Write Cycle 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CLK CKE VIH Read cycle /RAS-/CAS delay = 3 /CAS latency = 3 Burst length = 4 = VIH or VIL /CS /RAS /CAS /WE BS Address R:a C:a R:b C:b C:b' C:b" DQM DQ (output) DQ (input) a b b+1 b+2 b+3 b' b'+1 b" b"+1 b"+2 b"+3 High-Z Bank 0 Active EO CKE a+1 a+2 a+3 Bank 0 Read Bank 3 Active Bank 3 Bank 0 Read Precharge Bank 3 Read Bank 3 Read Bank 3 Precharge VIH Write cycle /RAS-/CAS delay = 3 /CAS latency = 3 Burst length = 4 = VIH or VIL /CS /RAS /CAS /WE BS Address R:a C:a R:b C:b C:b' C:b" DQM High-Z DQ (output) DQ (input) a a+1 a+2 a+3 L Bank 0 Active Bank 0 Write Bank 3 Active b Bank 3 Write b+1 b+2 b+3 b' Bank 0 Precharge Bank 3 Write b'+1 b" Bank 3 Write b"+1 b"+2 b"+3 Bank 3 Precharge t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 45 EDS1232AATA-MI Read/Single Write Cycle 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CLK CKE VIH /CS /RAS /CAS /WE BS R:a Address C:a R:b C:a' C:a DQM a DQ (input) EO DQ (output) Bank 0 Active CKE a Bank 0 Read Bank 3 Active C:a R:b a+1 a+2 a+3 a a+1 a+2 a+3 Bank 0 Bank 0 Write Read Bank 0 Precharge Bank 3 Precharge VIH /CS /RAS /CAS /WE BS Address R:a L C:a C:b C:c a b DQM DQ (input) DQ (output) Bank 0 Active Bank 0 Read a a+1 c a+3 Bank 0 Write Bank 3 Active Bank 0 Bank 0 Write Write Bank 0 Precharge t uc od Pr Read/Single write /RAS-/CAS delay = 3 /CAS latency = 3 Burst length = 4 = VIH or VIL Data Sheet E0340E30 (Ver. 3.0) 46 EDS1232AATA-MI Read/Burst Write Cycle 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CLK CKE /CS /RAS /CAS /WE BS R:a Address C:a R:b C:a' DQM a DQ (input) EO DQ (output) a Bank 0 Active CKE Bank 0 Read a+1 a+2 a+3 a+1 a+2 a+3 Clock suspend Bank 3 Active Bank 0 Precharge Bank 0 Write Bank 3 Precharge VIH /CS /RAS /CAS /WE BS DQM DQ (input) DQ (output) L Address R:a C:a Bank 0 Active Bank 0 Read 1 2 a a Bank 0 Write 3 4 5 6 7 VIH /CS /RAS /CAS /WE 8 9 10 11 12 Read/Burst write /RAS-/CAS delay = 3 /CAS latency = 3 Burst length = 4 = VIH or VIL 13 14 15 R:a A10=1 DQM DQ (input) t RP t RC Auto Refresh 16 t RC Auto Refresh Data Sheet E0340E30 (Ver. 3.0) 47 17 18 19 20 C:a a High-Z DQ (output) Precharge If needed Bank 0 Precharge t uc BS Address a+1 a+2 a+3 a+3 Bank 3 Active CLK CKE a+1 od 0 C:a Pr Auto Refresh Cycle R:b Active Bank 0 Read Bank 0 a+1 Refresh cycle and Read cycle /RAS-/CAS delay = 2 /CAS latency = 2 Burst length = 4 = VIH or VIL EDS1232AATA-MI Self Refresh Cycle CLK lSREX CKE Low CKE /CS /RAS /CAS /WE BS Address A10=1 EO DQM DQ (input) High-Z DQ (output) t RP Precharge command If needed t RC t RC Self refresh entry command Next clock enable Self refresh exit ignore command or No operation Auto Next clock refresh enable Self refresh entry command Self refresh cycle /RAS-/CAS delay = 3 CL = 3 BL = 4 = VIH or VIL Clock Suspend Mode L tSI 0 CLK CKE 1 2 3 4 5 tSI tHI 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Read cycle /RAS-/CAS delay = 2 /CAS latency = 2 Burst length = 4 = VIH or VIL /CS Pr /RAS /CAS /WE BS Address R:a C:a DQM DQ (output) R:b a C:b a+1 a+2 a+3 b b+1 b+2 b+3 High-Z DQ (input) Active clock Bank0 suspend end Read Bank3 Active /CS /RAS /CAS /WE BS C:a R:b R:a od Bank0 Active clock Active suspend start CKE Address 20 Read suspend start Read suspend end Bank3 Read Bank0 Precharge Bank0 Active Active clock suspend start a+1 a+2 Active clock Bank0 Bank3 supend end Write Active Write suspend start a+3 b Write suspend end Data Sheet E0340E30 (Ver. 3.0) 48 t uc High-Z DQ (output) a Write cycle /RAS-/CAS delay = 2 /CAS latency = 2 Burst length = 4 = VIH or VIL C:b DQM DQ (input) Earliest Bank3 Precharge b+1 b+2 b+3 Bank3 Bank0 Write Precharge Earliest Bank3 Precharge EDS1232AATA-MI Power Down Mode CLK CKE Low CKE /CS /RAS /CAS /WE BS EO Address R: a A10=1 DQM DQ (input) High-Z DQ (output) tRP Precharge command If needed Power down cycle Power down entry Power down /RAS-/CAS delay = 3 mode exit Active Bank 0 /CAS latency = 3 Burst length = 4 = VIH or VIL L Initialization Sequence 0 CLK CKE 1 2 3 4 5 6 7 8 9 10 48 49 50 51 52 53 54 55 VIH /CS Pr /RAS /CAS /WE valid Address DQM VIH code Valid od High-Z DQ t RC tRP All banks Precharge Auto Refresh tRC Auto Refresh lMRD Mode register Set Bank active If needed t uc Data Sheet E0340E30 (Ver. 3.0) 49 EDS1232AATA-MI Package Drawing 86-pin Plastic TSOP (II) Unit: mm 22.22 ± 0.10 *1 A EO PIN#1 ID 1 0.15 to 0.30 43 0.50 11.76 ± 0.20 44 10.16 86 B 0.10 M S A B 0.80 Nom 0.10 +0.08 −0.05 0.09 to 0.20 0.10 S 1.2 max. S 0.25 0 to 8° L 1.0 ± 0.05 0.81 max. 0.60 ± 0.15 Pr Note: 1. This dimension does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.20mm per side. ECA-TS2-0087-02 t uc od Data Sheet E0340E30 (Ver. 3.0) 50 EDS1232AATA-MI Recommended Soldering Conditions Please consult with our sales offices for soldering conditions of the EDS1232AA. Type of Surface Mount Device EDS1232AATA: 86-pin Plastic TSOP (II) L EO t uc od Pr Data Sheet E0340E30 (Ver. 3.0) 51 EDS1232AATA-MI NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR MOS DEVICES Exposing the MOS devices to a strong electric field can cause destruction of the gate oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it, when once it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. MOS devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. MOS devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor MOS devices on it. EO 2 HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES No connection for CMOS devices input pins can be a cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. The unused pins must be handled in accordance with the related specifications. L 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Pr Power-on does not necessarily define initial status of MOS devices. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the MOS devices with reset function have not yet been initialized. Hence, power-on does not guarantee output pin levels, I/O settings or contents of registers. MOS devices are not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for MOS devices having reset function. CME0107 t uc od Data Sheet E0340E30 (Ver. 3.0) 52 EDS1232AATA-MI The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Elpida Memory, Inc. Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights (including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or third parties by or arising from the use of the products or information listed in this document. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of Elpida Memory, Inc. or others. Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of the customer's equipment shall be done under the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. EO [Product applications] Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability. However, users are instructed to contact Elpida Memory's sales office before using the product in aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment, medical equipment for life support, or other such application in which especially high quality and reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk of bodily injury. L [Product usage] Design your application so that the product is used within the ranges and conditions guaranteed by Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no responsibility for failure or damage when the product is used beyond the guaranteed ranges and conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other consequential damage due to the operation of the Elpida Memory, Inc. product. [Usage environment] This product is not designed to be resistant to electromagnetic waves or radiation. This product must be used in a non-condensing environment. M01E0107 t uc od Pr If you export the products or technology described in this document that are controlled by the Foreign Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by U.S. export control regulations, or another country's export control laws or regulations, you must follow the necessary procedures in accordance with such laws or regulations. If these products/technology are sold, leased, or transferred to a third party, or a third party is granted license to use these products, that third party must be made aware that they are responsible for compliance with the relevant laws and regulations. Data Sheet E0340E30 (Ver. 3.0) 53