MC10EP05, MC100EP05 3.3V / 5VECL 2−Input Differential AND/NAND Description The MC10/100EP05 is a 2−input differential AND/NAND gate. The device is functionally equivalent to the EL05 and LVEL05 devices. With AC performance much faster than the LVEL05 device, the EP05 is ideal for applications requiring the fastest AC performance available. The 100 Series contains temperature compensation. http://onsemi.com MARKING DIAGRAMS* 8 8 Features 1 • 220 ps Typical Propagation Delay • Maximum Frequency > 3 GHz Typical • PECL Mode Operating Range: VCC = 3.0 V to 5.5 V 8 HEP05 ALYWG G SOIC−8 D SUFFIX CASE 751 1 KEP05 ALYWG G 1 with VEE = 0 V 1 TSSOP−8 DT SUFFIX CASE 948R 1 8 HP05 ALYWG G 1 KP05 ALYWG G 5I DG G • • • • 8 8 with VEE = −3.0 V to −5.5 V Open Input Default State Safety Clamp on Inputs Q Output Will Default LOW with Inputs Open or at VEE Pb−Free Packages are Available 2X DG G • NECL Mode Operating Range: VCC = 0 V 1 4 1 4 A L Y W G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package DFN8 MN SUFFIX CASE 506AA H K 5I 2X D = MC10 = MC100 = MC10 = MC100 = Date Code (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. © Semiconductor Components Industries, LLC, 2006 November, 2006 − Rev. 8 1 Publication Order Number: MC10EP05/D MC10EP05, MC100EP05 Table 1. PIN DESCRIPTION D0 D0 1 8 2 7 Pin VCC Q Function D0*, D1*, D0**, D1** ECL Data Inputs Q, Q ECL Data Outputs VCC Positive Supply VEE Negative Supply * Pins will default LOW when left open. ** Pins will default to VCC/2when left open. D1 6 3 Q Table 2. TRUTH TABLE D1 4 5 VEE D0 D1 D0 D1 Q Q L L H H L H L H H H L L H L H L L L L H H H H L Figure 1. 8−Lead Pinout (Top View) and Logic Diagram Table 3. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 kW Internal Input Pullup Resistor ESD Protection 37.5 kW Human Body Model Machine Model Charged Device Model Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) SOIC−8 TSSOP−8 DFN8 Flammability Rating Oxygen Index: 28 to 34 Transistor Count > 4 kV > 200 V > 2 kV Pb Pkg Pb−Free Pkg Level 1 Level 1 Level 1 Level 1 Level 3 Level 1 UL 94 V−0 @ 0.125 in 137 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. http://onsemi.com 2 MC10EP05, MC100EP05 Table 4. MAXIMUM RATINGS Rating Unit VCC Symbol PECL Mode Power Supply Parameter VEE = 0 V Condition 1 6 V VEE NECL Mode Power Supply VCC = 0 V −6 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 −6 V V Iout Output Current Continuous Surge 50 100 mA mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm SOIC−8 SOIC−8 190 130 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board SOIC−8 41 to 44 °C/W qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm TSSOP−8 TSSOP−8 185 140 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board TSSOP−8 41 to 44 °C/W qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm DFN8 DFN8 129 84 °C/W °C/W Tsol Wave Solder <2 to 3 sec @ 248°C <2 to 3 sec @ 260°C 265 265 °C Pb Pb−Free Condition 2 VI v VCC VI w VEE Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Table 5. 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 2) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 20 24 29 20 24 29 20 24 29 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 3) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV VOL Output LOW Voltage (Note 3) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV VIH Input HIGH Voltage (Single−Ended) 2090 2415 2155 2480 2215 2540 mV VIL Input LOW Voltage (Single−Ended) 1365 1690 1460 1755 1490 1815 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 4) 2.0 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 mA IIL Input LOW Current 150 D D 0.5 −150 150 0.5 −150 0.5 −150 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V. 3. All loading with 50 W to VCC − 2.0 V. 4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 3 MC10EP05, MC100EP05 Table 6. 10EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 5) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 20 24 29 20 24 29 20 24 29 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 6) 3865 3990 4115 3930 4055 4180 3990 4115 4240 mV VOL Output LOW Voltage (Note 6) 3065 3190 3315 3130 3255 3380 3190 3315 3440 mV VIH Input HIGH Voltage (Single−Ended) 3790 4115 3855 4180 3915 4240 mV VIL Input LOW Voltage (Single−Ended) 3065 3390 3130 3455 3190 3515 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 7) 2.0 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current 150 D D 150 0.5 −150 0.5 −150 mA 0.5 −150 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V. 6. All loading with 50 W to VCC − 2.0 V. 7. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 7. 10EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 8) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 20 24 29 20 24 29 20 24 29 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 9) −1135 −1010 −885 −1070 −945 −820 −1010 −885 −760 mV VOL Output LOW Voltage (Note 9) −1935 −1810 −1685 −1870 −1745 −1620 −1810 −1685 −1560 mV VIH Input HIGH Voltage (Single−Ended) −1210 −885 −1145 −820 −1085 −760 mV VIL Input LOW Voltage (Single−Ended) −1935 −1610 −1870 −1545 −1810 −1485 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 10) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current VEE+2.0 0.0 VEE+2.0 150 D D 0.5 −150 0.0 VEE+2.0 150 0.5 −150 0.5 −150 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 8. Input and output parameters vary 1:1 with VCC. 9. All loading with 50 W to VCC − 2.0 V. 10. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 4 MC10EP05, MC100EP05 Table 8. 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 11) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 15 25 32 17 27 36 19 28 38 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 12) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV VOL Output LOW Voltage (Note 12) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV VIH Input HIGH Voltage (Single−Ended) 2075 2420 2075 2420 2075 2420 mV VIL Input LOW Voltage (Single−Ended) 1355 1675 1355 1675 1355 1675 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 13) 2.0 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 mA IIL Input LOW Current 150 D D 0.5 −150 150 0.5 −150 mA 0.5 −150 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 11. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V. 12. All loading with 50 W to VCC − 2.0 V. 13. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 9. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 14) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 15 25 32 17 27 36 19 28 38 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 15) 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV VOL Output LOW Voltage (Note 15) 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV VIH Input HIGH Voltage (Single−Ended) 3775 4120 3775 4120 3775 4120 mV VIL Input LOW Voltage (Single−Ended) 3055 3375 3055 3375 3055 3375 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 16) 2.0 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current 150 D D 0.5 −150 150 0.5 −150 0.5 −150 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 14. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V. 15. All loading with 50 W to VCC − 2.0 V. 16. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 5 MC10EP05, MC100EP05 Table 10. 100EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 17) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 15 25 32 17 27 36 19 28 38 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 18) −1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV VOL Output LOW Voltage (Note 18) −1945 −1820 −1695 −1945 −1820 −1695 −1945 −1820 −1695 mV VIH Input HIGH Voltage (Single−Ended) −1225 −880 −1225 −880 −1225 −880 mV VIL Input LOW Voltage (Single−Ended) −1945 −1625 −1945 −1625 −1945 −1625 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 19) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current VEE+2.0 0.0 VEE+2.0 0.0 150 D D 0.5 −150 VEE+2.0 150 0.5 −150 mA 0.5 −150 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 17. Input and output parameters vary 1:1 with VCC. 18. All loading with 50 W to VCC − 2.0 V. 19. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 11. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 20) −40°C Symbol Characteristic Min fmax Maximum Frequency (Figure 2) tPLH, tPHL Propagation Delay to Output Differential tJITTER Random Clock Jitter (Figure 2) VPP Input Voltage Swing (Differential Configuration) tr tf Output Rise/Fall Times (20% − 80%) Typ 25°C Max Min >3 160 Q Typ 85°C Max Min >3 210 260 0.2 <1 150 800 1200 70 120 170 170 Typ Max >3 220 270 0.2 <1 150 800 1200 80 130 180 210 Unit GHz 260 320 ps 0.2 1.5 ps 150 800 1200 mV 100 150 200 ps NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 20. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V. http://onsemi.com 6 MC10EP05, MC100EP05 VOUTamplitude (mVpp) 5V 9 750 8 3.3 V 7 650 6 550 5 ÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉ 4 450 350 JITTER OUT ps (RMS) 10 850 3 2 1 (JITTER) 250 1.0 0 1.5 2.0 2.5 FREQUENCY (GHz) 3.0 Figure 2. Fmax/Jitter @ 255C Q Zo = 50 W D Receiver Device Driver Device Q Zo = 50 W D 50 W 50 W VTT VTT = VCC − 2.0 V Figure 3. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) http://onsemi.com 7 MC10EP05, MC100EP05 ORDERING INFORMATION Package Shipping † SOIC−8 98 Units / Rail MC10EP05DG SOIC−8 (Pb−Free) 98 Units / Rail MC10EP05DR2 SOIC−8 2500 / Tape & Reel MC10EP05DR2G SOIC−8 (Pb−Free) 2500 / Tape & Reel MC10EP05DT TSSOP−8 100 Units / Rail MC10EP05DTG TSSOP−8 (Pb−Free) 100 Units / Rail MC10EP05DTR2 TSSOP−8 2500 / Tape & Reel MC10EP05DTR2G TSSOP−8 (Pb−Free) 2500 / Tape & Reel MC10EP05MNR4 DFN8 1000 / Tape & Reel DFN8 (Pb−Free) 1000 / Tape & Reel SOIC−8 98 Units / Rail MC100EP05DG SOIC−8 (Pb−Free) 98 Units / Rail MC100EP05DR2 SOIC−8 2500 / Tape & Reel MC100EP05DR2G SOIC−8 (Pb−Free) 2500 / Tape & Reel MC100EP05DT TSSOP−8 100 Units / Rail MC100EP05DTG TSSOP−8 (Pb−Free) 100 Units / Rail MC100EP05DTR2 TSSOP−8 2500 / Tape & Reel MC100EP05DTR2G TSSOP−8 (Pb−Free) 2500 / Tape & Reel MC100EP05MNR4 DFN8 1000 / Tape & Reel DFN8 (Pb−Free) 1000 / Tape & Reel Device MC10EP05D MC10EP05MNR4G MC100EP05D MC100EP05MNR4G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 8 MC10EP05, MC100EP05 PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE AH NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. −X− A 8 5 0.25 (0.010) S B 1 M Y M 4 K −Y− G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 9 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC10EP05, MC100EP05 PACKAGE DIMENSIONS TSSOP−8 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948R−02 ISSUE A 8x 0.15 (0.006) T U K REF 0.10 (0.004) S 2X L/2 8 1 PIN 1 IDENT S T U V S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. S 5 0.25 (0.010) B −U− L 0.15 (0.006) T U M M 4 A −V− F DETAIL E C 0.10 (0.004) −T− SEATING PLANE D −W− G DETAIL E http://onsemi.com 10 DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0_ 6_ INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0_ 6_ MC10EP05, MC100EP05 PACKAGE DIMENSIONS DFN8 CASE 506AA−01 ISSUE D D A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994 . 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. B PIN ONE REFERENCE 2X 0.10 C 2X ÇÇÇÇ ÇÇÇÇ ÇÇÇÇ 0.10 C E DIM A A1 A3 b D D2 E E2 e K L TOP VIEW A 0.10 C MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.20 0.30 2.00 BSC 1.10 1.30 2.00 BSC 0.70 0.90 0.50 BSC 0.20 −−− 0.25 0.35 8X 0.08 C SEATING PLANE (A3) SIDE VIEW A1 C D2 e e/2 4 1 8X L E2 K 8 5 8X b 0.10 C A B 0.05 C NOTE 3 BOTTOM VIEW ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10EP05/D