LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only LED SMD Pb Lead-Free Parts LG-192HRF-CT-08 DATA SHEET DOC. NO : QW0905-LG-192HRF-CT-08 REV : C DATE : 19 - May. - 2016 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/11 PART NO. LG-192HRF-CT-08 Features: 1. Package in 8.0mm carrier tape on 7" diameter reel. 2. Compatible with automatic placement equipment. 3. Compatible with reflow solder process. Descriptions: 1. The LG-192 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. 2. Besides, lightweight makes them ideal for miniature applications. etc. Applications: 1. Automotive : backlighting in dashboard and switch. 2. Telecommunication : indicator and backlighting in telephone and fax. 3. Flat backlight for LCD, switch and symbol 4. General use. Device Selection Guide: PART NO MATERIAL LG-192HRF-CT-08 AIGaInP COLOR Emitted Lens Red Water Clear LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/11 PART NO. LG-192HRF-CT-08 Package Dimensions Cathode Mark 0.4 0.2 0.8 Resin Cathode Mark 0.3 LED DICE 1.6 1.0 Soldering Terminal 1.0 0.6 0.3 PCB Note : 1.All dimension are in millimeter tolerance is ±0.1mm unless otherwise noted. 2.Specifications are subject to change without notice. Recommended Soldering Pad Dimensions 0.8 0.8 0.7 0.8 Note : The tolerances unless mentioned is ±0.1mm,Angle ±0.5. Unit=mm. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/11 PART NO. LG-192HRF-CT-08 Absolute Maximum Ratings at Ta=25℃ Symbol Ratings UNIT Power Dissipation PD 60 mW Peak Forward Current Duty 1/10@10KHz IFP 75 mA Forward Current IF 25 mA Reverse Current @5V Ir 10 μA Electrostatic Discharge ESD 2000 V Operating Temperature Topr -40 ~ + 85 ℃ Storage Temperature Tstg -40 ~ + 100 ℃ Parameter Typical Electrical & Optical Characteristics (Ta=25℃) Symbol Min. Typ. Luminous Intensity Iv 32 80 ---- mcd IF=20mA Dominant Wavelength λD ---- 630 ---- nm IF=20mA △λ ---- 20 ---- nm IF=20mA VF 1.5 ---- 2.4 V IF=20mA 2θ 1/2 ---- 130 ---- deg IF=20mA Items Spectral Line Half-Width Forward Voltage Viewing Angle Max. UNIT Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 3.The dominant wavelength data did not including ±1nm testing tolerance CONDITION LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 4/11 PART NO. LG-192HRF-CT-08 Luminous Intensity Classification BIN CODE Iv(mcd) at 20mA Min. Max. N 32 50 P 50 80 Q 80 125 R 125 200 Dominant Wavelength Classification BIN CODE λD(nm) at 20mA Min. Max. 29 624 627 30 627 630 31 630 633 32 633 636 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 5/11 PART NO. LG-192HRF-CT-08 Typical Electro-Optical Characteristics Curve HRF CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.5 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1.0 3.0 2.5 2.0 1.5 1.0 0.5 0 0.1 1.0 1.5 2.0 2.5 3.0 1.0 10 1000 Forward Current(mA) Forward Voltage(V) Fig.3 Forward Current vs. Temperature Fig.4 Relative Intensity vs. Temperature 40 3.0 30 20 10 0 0 20 40 60 80 100 Relative Intensity@20mA Normalize@25℃ Forward Current(mA) 100 2.5 2.0 1.5 1.0 0.5 0 -40 -20 -0 20 40 60 80 Ambient Temperature (Ta°C) Ambient Temperature( ℃) Relative Intensity@20mA Fig.5 Relative Intensity vs. Wavelength Fig.6 Directive Radiation 1.0 0.5 0 550 600 650 Wavelength (nm) 700 130° 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 6/11 PART NO. LG-192HRF-CT-08 Carrier Tape Dimensions 2.0 4.0 ±0.2 0.23 1.5 1.75 3.5±0.2 8.0 ±0.3 5.4 1.75 Polarity 0.6 4.0±0.2 0.9 Note : The tolerances unless mentioned is ± 0.1mm,Angle ± 0.5. Unit=mm. ‧ Packing Specifications Label Aluminum Moist-Proff bag Label Part No. Description Quantity/Reel LG-192HRF-CT-08 8.0mm tape,7"reel 4000 devices LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 7/11 PART NO. LG-192HRF-CT-08 Label Explanation Pb LIGITEK ELECTRONICS CO., LTD. PART : LG-192HRF-CT-08 BIN : Luminous Intensity LOT : GS11410168 HUE : Dominant Wavelength QTY(PCS): 4000 VF : Forward Voltage BIN/HUE : N/29 VF:2.0-2.2 Reel Dimensions 0.2 0.4 0.8 0.8 0.6 0.2 0.4 0.6 2.0±0.5 178 ±1.5 6.0 ±1.0 9.0±1.0 ψ13.5±1.0 12.0±1.0 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 8/11 PART NO. LG-192HRF-CT-08 Box Explanation 1. 5 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm L W H LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LG-192HRF-CT-08 Page 9/11 Recommended Soldering Conditions 1. Hand Solder Basic spec is ≦ 280 ℃ 3 sec one time only. 2 PB-Free Reflow Solder 1~5°C/sec 1~5°C/sec Preheat 180~200°C 260°C MaX. 10sec.Max 6°C/sec Above 220°C 60 sec.Max. 120 sec.Max. Note: 1.Reflow soldering should not be done more than two times. 2.When soldering,do not put stress on the LEDs during heating. 3.After soldering,do not warp the circuit board. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 10/11 PART NO. LG-192HRF-CT-08 Precautions For Use: Storage time: 1. Calculated shelf life before opening is 18 months at < 30°C and < 90% relative humidity (RH) 2. After bag is opened, devices which will be subjected to reflow soldering or other high temperature processes must be a) Assemblied within one years in an environment of ≦ 30°C / 60% RH, or b) Stored at ambient of 10% RH or less 3. Devices are required baking before assembly if: a) Humidity Indicator Card reads >10% (for level 2a -5a) or >60% (for level 2) at ambient temperature 23 ±5°C b) 2.a) or 2.b) doesn't meet 4. If baking is required, devices should be baked for >24 hours at 60±5°C.Performing baking only once, and using the baked devices within 72 hours.. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 11/11 PART NO. LG-192HRF-CT-08 Reliability Test: Classification Test Item Test Condition Sample Size Operating Life Test 1.Ta=25°C 2.If=20mA 3.t=1000 hrs (-24hrs,+72hrs) 22 High Temperature Storage Test 1.Ta=100°C±5°C 2.t=1000 hrs (-24hrs,+72hrs) 22 Low Temperature Storage Test 1.Ta=-40°C±5°C 2.t=1000 hrs (-24hrs,+72hrs) 22 High Temperature High Humidity Storage Test 1.Ta=85°C 2.RH=85% 3.t=1000hrs(-24hrs,+72hrs) 22 1.Ta=100°C±5°C ~ -40°C±5°C 20min/ 10sec / 20min 2.total 100 cycles 22 1.100°C±5°C ~ -40°C±5°C 30mins / 5mins / 30mins 2.100 Cyeles 22 Endurance Test Thermal Shock Test Environmental Test Temperature Cycling IR Reflow 1.T=260°C Max. 10sec.Max. 2. 6 Min 22