Ordering number : ENA0078 Monolithic Linear IC LA42352 5W 2-Channel AF Power Amplifier With DC Volume Control Overview LA42352 is 5W 2-channel AF power amplifier with DC volume control intended for televisions. LA42000 series is power IC which made Pin compatible possible altogether in 3 to 15W. They consist of four kinds of power ICs. (mono, stereo, mono with volume function, stereo with volume function.). They realized PCB layout communalization of an audio power block of TV. Channel PO Mono LA42051 5W LA42052 5W LA42351 5W LA42352 5W LA42071 7W LA42072 7W LA42152 15W ° ° ° Volume Stereo ° ° ° ° ° ° Feature • PO 5W×2ch (VCC = 18V, RL = 8Ω, THD = 10%) • Built-in DC Volume Control. • Built-in Standby function. • Built-in overheat protection. Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein. 92706 / 83005 MS PC B8-9060 No.A0078-1/9 LA42352 Specitications Maximum Ratings at Ta = 25 °C Parameter Symbol Maximum supply voltage VCC max Allowable power dissipation Pd max Maximum junction temperature Tj max Conditions Ratings Unit No signal 24 Infinite heat sink 15 W 150 °C θjc Thermal resistance V 3 °C/W Operating temperature Topr -25 to +75 °C Storage temperature Tstg -40 to +150 °C Operating Conditions at Ta = 25 °C Parameter Symbol Conditions Ratings Unit Recommended supply voltage VCC 18 V Recommended load resistance RL 8 Ω 10 to 22 V Allowable operating voltage range VCC op Operating Characteristics at Ta = 25°C, VCC = 18V, RL = 8Ω, Volume = 5V, f = 1kHz, Rg = 600Ω Parameter Symbol Ratings Conditions min Standby current ISTB typ 1 10 µA 35 65 130 mA 4 5 Amplifier off Quiescent current ICCO Rg = 0, Volume = 0V Output power PO THD = 10% Total harmonic distortion THD PO = 1W Unit max 32.5 W 0.1 0.8 % 34.5 36.5 dB 0.13 0.4 mVrms Voltage gain VG VO = 0dBm Output noise voltage VNO Rg = 0, Volume = 0V, Volume Attenuation Att VIN = 100mV, Vcont = 0V, with 1k-BPF 70 80 dB Channel separation Sep. Rg = 10kΩ, VO = 0dBm 48 55 dB Standby control voltage VSTB-H Amplifier on 2.5 10 V (The Pin 5 voltage) VSTB-L Amplifier off 0 0.5 V Input resistance Ri 26 kΩ BPF = 20Hz to 20kHz 14 20 *0dBm = 1mW (600Ω) = 774.6mVrms Package Dimensions unit : mm 3107B No.A0078-2/9 LA42352 Block Diagram Standby VCC 5 7 Ri = 20kΩ Input amplifier IN1 Output amplifier 2 12 OUT1 Volume 1 13 Pre GND 3 11 NF1 Thermal protection circuit Ri = 20kΩ 10 Power GND 8 OUT2 9 NF2 Input amplifier IN2 Volume 2 Output amplifier 4 6 Ripple Filter Block 1 Ripple Filter Sample Application Circuit LA42352 Ripple Filter IN1 PRE GND IN2 STB Vol 2 1 2 3 4 5 6 C3 + 47µF /25V VCC OUT2 NF2 PWR GND NF1 OUT1 Vol 1 7 8 9 10 11 12 13 +5V + C1 1.0µF /10V + C2 1.0µF /10V R3 10kΩ C4 1000µF /25V + C9 + 47µF /16V + + CPU C7 0.1µF R1 2.2Ω C5 470µF /16V +5V C10 47µF /16V + RL RL C6 470µF /16V C8 0.1µF R2 2.2Ω No.A0078-3/9 LA42352 Pin Descriptions Pin No Symbol Pin Voltage Equivalent Circuit Description 1 RF VCC = 18V 17.6 2 IN1 4.4 4 IN2 3 PRE_GND 0 • Pre GND pin 5 STB 0 to 5V • Standby pin (Input voltage) • Ripple filter reference • Input pin • The standby function is on when this pin at ground level 6 Vol 2 0 to 5V 13 Vol 1 (Input voltage) 7 VCC 18 • Control Volume • Power supply Continued on next page. No.A0078-4/9 LA42352 Continued from preceding page. Pin No Symbol 8 OUT2 12 OUT1 9 NF2 10 NF1 Pin Voltage VCC = 18V 8.9 8.8 Equivalent Circuit Description • Output pin • Negative feedback pin at Power amplifier • Connect NF capacitor 10 PWR_GND 0 • Power GND pin Description of External parts C1, C2 C3 C4 C5, C6 C7, C8 C9, C10 R1, R2 R3 : Input capacitors. A value of 1.0µF is recommended for capacitors. Note that the low-frequency area characteristics can be adjusted by changing fL. : Ripple filter capacitor. A value of 47µF is recommended for capacitors. Decreasing the capacitance value excessively or removing this capacitor causes ripple to occur. However, increasing the capacitance value does not always cause ripple to reduced. Decreasing the capacitance value makes the starting time earlier. : Power capacitor. : Output capacitors. A value of 470µF is recommended for capacitors. : Oscillation blocking capacitor. Use a polyester film capacitor that is good in high frequency response and temperature characteristic. : Feedback capacitor. A value of 47µF is recommended for capacitors. Decreasing the capacitance value lowers the low frequency response. Increasing the capacitance value makes the starting time later. : Resistor connected in series with oscillation blocking capacitor. Prevents phase shift attributable to the oscillation blocking capacitor so that oscillation is hard to occur. : Standby switch current limiting resistor. A value of 10kΩ is recommended for resistance (when the applied voltage for the standby switch is 3V to 10V). This resistor cannot be removed. No.A0078-5/9 LA42352 Features of IC Inside and Usage Note Standby function • Pin 5 is the standby switch pin. The amplifier is turned on by applying approximately 3V or more to this pin through an external resistor (R3). • If voltage in excess of 10V is to be applied to the standby switch, calculate the value of R3 using the following formula so that the current flowing into pin 5 is 500µA or less: R3 = (Applied voltage − 2VBE (≈1.4V)) − 15kΩ 500µA Protector • In order to prevent damage or degradation which may be caused by abnormally heated IC, the LA42352 has a thermal shutdown protector. Accordingly, if the IC junction temperature (Tj) climbs to around 160°C due to inadequate heat dissipation, the thermal shutdown protector will operate to control the output gradually into attenuation. No.A0078-6/9 LA42352 No.A0078-7/9 LA42352 No.A0078-8/9 LA42352 Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of August, 2005. Specifications and information herein are subject to change without notice. PS No.A0078-9/9