MAX2055EUP Rev. A RELIABILITY REPORT FOR MAX2055EUP PLASTIC ENCAPSULATED DEVICES April 2, 2004 MAXIM INTEGRATED PRODUCTS 120 SAN GABRIEL DR. SUNNYVALE, CA 94086 Written by Reviewed by Jim Pedicord Quality Assurance Reliability Lab Manager Bryan J. Preeshl Quality Assurance Executive Director Conclusion The MAX2055 successfully meets the quality and reliability standards required of all Maxim products. In addition, Maxim’s continuous reliability monitoring program ensures that all outgoing product will continue to meet Maxim’s quality and reliability standards. Table of Contents I. ........Device Description II. ........Manufacturing Information III. .......Packaging Information IV. .......Die Information V. ........Quality Assurance Information VI. .......Reliability Evaluation ......Attachments I. Device Description A. General The MAX2055 high-performance, digitally controlled, variable-gain, differential analog-to-digital converter (ADC) driver/amplifier (DVGA) is designed for use from 30MHz to 300MHz in base-station receivers. The device integrates a digitally controlled attenuator and a high-linearity single-ended-to-differential output amplifier, which can either eliminate an external transformer, or can improve the even-order distortion performance of a transformer-coupled circuit, thus relaxing the requirements of the anti-alias filter preceding an ADC. Targeted for ADC driver applications to adjust gain either dynamically or as a one-time channel gain setting, the MAX2055 is ideal for applications requiring high performance. The attenuator provides 23dB of attenuation range with ±0.2dB accuracy. The MAX2055 is available in a thermally enhanced 20-pin TSSOP-EP package and operates over the -40°C to +85°C temperature range. B. Absolute Maximum Ratings Item All Pins to GND Input Signal (RF_IN) Output Power (RF_OUT) Operating Temperature Range Junction Temperature Storage Temperature Range Lead Temperature (soldering, 10s) Continuous Power Dissipation (TA = +85°C) 28-Pin TSSOP Derates above +85°C 28-Pin TSSOP Rating -0.3V to +(VCC + 0.25V) 20dBm 24dBm -40°C to +85°C +150°C -65°C to +165°C +300°C 2100mW 21.7mW/°C II. Manufacturing Information A. Description/Function: Digitally Controlled, Variable-Gain, Differential ADC Driver/Amplifier B. Process: GST4 C. Number of Device Transistors: 325 D. Fabrication Location: Oregon, USA E. Assembly Location: Philippines or Malaysia F. Date of Initial Production: April, 2003 III. Packaging Information A. Package Type: 28-Pin TSSOP B. Lead Frame: Copper C. Lead Finish: Solder Plate D. Die Attach: Silver-filled epoxy E. Bondwire: Gold (1.2 mil dia.) F. Mold Material: Epoxy with silica filler G. Assembly Diagram: Buildsheet # 05-9000-0419 H. Flammability Rating: Class: UL94-V0 I. Classification of Moisture Sensitivity per JEDEC standard J-STD-020-A: Level 1 IV. Die Information A. Dimensions: 125 x 79 mils B. Passivation: Si3N4 (Silicon nitride) C. Interconnect: Au D. Backside Metallization: None E. Minimum Metal Width: Metal1: 1.2; Metal2: 1.2; Metal3: 1.2; Metal4: 5.6 microns (as drawn) F. Minimum Metal Spacing: Metal1: 1.6; Metal2: 1.6; Metal3: 1.6; Metal4: 4.2 microns (as drawn) G. Bondpad Dimensions: 5 mil. Sq. H. Isolation Dielectric: SiO2 I. Die Separation Method: Wafer Saw V. Quality Assurance Information A. Quality Assurance Contacts: Jim Pedicord (Manager, Reliability Operations) Bryan Preeshl (Executive Director of QA) Kenneth Huening (Vice President) B. Outgoing Inspection Level: 0.1% for all electrical parameters guaranteed by the Datasheet. 0.1% For all Visual Defects. C. Observed Outgoing Defect Rate: < 50 ppm D. Sampling Plan: Mil-Std-105D VI. Reliability Evaluation A. Accelerated Life Test The results of the 150°C biased (static) life test are shown in Table 1. Using these results, the Failure Rate (λ) is calculated as follows: λ= 1 = MTTF 1.83 (Chi square value for MTTF upper limit) 192 x 9823 x 45 x 2 Temperature Acceleration factor assuming an activation energy of 0.8eV λ = 10.78 x 10-8 λ = 10.78 F.I.T. (60% confidence level @ 25°C) This low failure rate represents data collected from Maxim’s reliability qualification and monitor programs. Maxim also performs weekly Burn-In on samples from production to assure reliability of its processes. The reliability required for lots which receive a burn-in qualification is 59 F.I.T. at a 60% confidence level, which equates to 3 failures in an 80 piece sample. Maxim performs failure analysis on rejects from lots exceeding this level. The Burn-In Schematic (Spec.# 06-7097) shows the static circuit used for this test. Maxim also performs 1000 hour life test monitors quarterly for each process. This data is published in the Product Reliability Reports (RR-1M & RR-B3A). B. Moisture Resistance Tests Maxim evaluates pressure pot stress from every assembly process during qualification of each new design. Pressure Pot testing must pass a 20% LTPD for acceptance. Additionally, industry standard 85°C/85%RH or HAST tests are performed quarterly per device/package family. C. E.S.D. and Latch-Up Testing The CR17 die type has been found to have all pins able to withstand a transient pulse of +/-200V, per Mil-Std883 Method 3015 (reference attached ESD Test Circuit). Latch-Up testing has shown that this device withstands a current of ±250mA. Table 1 Reliability Evaluation Test Results MAX2055EUP TEST ITEM TEST CONDITION Static Life Test (Note 1) Ta = 150°C Biased Time = 192 hrs. FAILURE IDENTIFICATION SAMPLE SIZE NUMBER OF FAILURES DC Parameters & functionality 45 0 Moisture Testing (Note 2) Pressure Pot Ta = 121°C P = 15 psi. RH= 100% Time = 168hrs. DC Parameters & functionality 77 0 85/85 Ta = 85°C RH = 85% Biased Time = 1000hrs. DC Parameters & functionality 77 0 DC Parameters & functionality 77 Mechanical Stress (Note 2) Temperature Cycle -65°C/150°C 1000 Cycles Method 1010 Note 1: Life Test Data may represent plastic DIP qualification lots. Note 2: Generic process/package data. 0 Attachment #1 TABLE II. Pin combination to be tested. 1/ 2/ Terminal A (Each pin individually connected to terminal A with the other floating) Terminal B (The common combination of all like-named pins connected to terminal B) 1. All pins except VPS1 3/ All VPS1 pins 2. All input and output pins All other input-output pins 1/ Table II is restated in narrative form in 3.4 below. 2/ No connects are not to be tested. 3/ Repeat pin combination I for each named Power supply and for ground (e.g., where VPS1 is VDD, VCC, VSS, VBB, GND, +VS, -VS, VREF, etc). 3.4 Pin combinations to be tested. a. Each pin individually connected to terminal A with respect to the device ground pin(s) connected to terminal B. All pins except the one being tested and the ground pin(s) shall be open. b. Each pin individually connected to terminal A with respect to each different set of a combination of all named power supply pins (e.g., VSS1, or VSS2 or VSS3 or VCC1 , or VCC2 ) connected to terminal B. All pins except the one being tested and the power supply pin or set of pins shall be open. c. Each input and each output individually connected to terminal A with respect to a combination of all the other input and output pins connected to terminal B. All pins except the input or output pin being tested and the combination of all the other input and output pins shall be open. TERMINAL C R1 R2 S1 TERMINAL A REGULATED HIGH VOLTAGE SUPPLY S2 C1 DUT SOCKET SHORT TERMINAL B Mil Std 883D Method 3015.7 Notice 8 TERMINAL D R = 1.5kΩ C = 100pf CURRENT PROBE (NOTE 6) DOCUMENT I.D. 06-7097 REVISION B B MAXIM TITLE: BI Circuit (MAX2055) CR17Z PAGE 2