EPCOS B82144A2153K000 Inductor Datasheet

Inductors
RF chokes, LBC series
Series/Type:
B82144A
Date:
March 2008
%BUB4IFFU
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures
hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
RF chokes
B82144A
LBC series, 5.2 s 12 (mm)
LBC choke (Large Bobbin Core)
Rated inductance 1 NH to 100 000 NH
Rated current 20 mA to 2200 mA
Construction
■ Large ferrite drum core
■ Winding: enamel copper wire
■ Flame-retardant lacquer coating
Features
■
■
■
■
Very wide inductance range
High rated current
Suitable for wave soldering
RoHS-compatible
Applications
■ RF blocking and filtering
■ Decoupling and interference suppression
■ For telecommunications (12- or 16-kHz blocking filter),
automotive electronics, energy-saving lamps,
entertainment electronics
Terminals
■ Central axial leads
■ Base material CuAg0.1
■ Hot-dipped with pure tin
Marking
Inductance indicated by color bands to IEC 60062
Delivery mode and packing units
■ Taped, Ammo and reel packing
■ Packing units:
Axial
Ammo
(pcs./pack.)
Reel
(pcs./reel)
1250
1500
Please read Cautions and warnings and
Important notes at the end of this document.
2
03/08
RF chokes
B82144A
LBC series, 5.2 s 12 (mm)
65±1
53±2
65±1
53±2
12 max.
(IEC
60294)
9.2
max.
(IEC 60294)
3.5min.
min.
3.5
11.5
14.8max.
max.
lacquered
lacquered
6±0.5
6±0.5
5±0.25 5±0.25
10±0.25 10±0.25
ø0.8 max.
ø0.8 max.
ø5.2 max.
ø4 max.
Dimensional drawing
Dimensions in mm
Minimum lead spacing 15 mm
IND0429-B-E
IND0431-4-E
n
w
30
H
30
ø360 _ 1
ø30.5±0.15
ø82+1
ø90
Packing
Label
30
L
IND0452-V-E
W
n (mm): 72 +1
w (mm): 84 max
L × W × H (max. mm): 265 × 75 × 125
Dimensions in mm
Please read Cautions and warnings and
Important notes at the end of this document.
IND0635-W-E
3
03/08
RF chokes
B82144A
LBC series, 5.2 s 12 (mm)
Technical data and measuring conditions
Rated inductance LR
Measured with LCR meter Agilent 4284A
or impedance analyzer Agilent 4294A
= 1 MHz
Measuring frequency:
LR ≤ 10 μH
10 μH < LR ≤ 4700 μH = 100 kHz
= 10 kHz
LR > 4700 μH
Measuring current:
≤ 1 mA
Measuring temperature: 20 °C
Q factor Qmin
Measured with precision impedance analyzer Agilent 4294A, 20 °C
Rated temperature TR
40 °C
Rated current IR
Maximum permissible DC current at rated temperature
Inductance decrease ΔL/L0
≤ 10% (referred to initial value) at IR, 20 °C
DC resistance Rmax
Measured at 20 °C
Resonance frequency fres,min Measured with Agilent 4294A or 8753ES, 20 °C
Solderability (lead-free)
Sn95.5Ag3.8Cu0.7: (245 ±5) °C, (3 ±0.3) s
Wetting of soldering area ≥ 90%
(to IEC 60068-2-20, test Ta)
Resistance to soldering heat
(260 ±5) °C, 10 s (to IEC 60068-2-20, test Tb)
Tensile strength of leads
≥ 20 N (to IEC 60068-2-21, test Ua)
Climatic category
55/125/56 (to IEC 60068-1)
Storage conditions
Mounted: –55 °C … +125 °C
Packaged: –25 °C … +40 °C, ≤ 75% RH
Weight
Approx. 1.1 g
Mounting information
When bending the leads, take care that the start-of-winding areas at the face ends (protected by
glue and lacquer) are not subjected to any mechanical stress.
Please read Cautions and warnings and
Important notes at the end of this document.
4
03/08
RF chokes
B82144A
LBC series, 5.2 s 12 (mm)
Characteristics and ordering codes
Tolerance1)
LR
Qmin
fQ
IR
Rmax
fres,min
MHz
mA
Ω
MHz
Ordering code
(reel packing) 2)
40
7.96
2200
0.08
200
B82144A2102K000
1.5
40
7.96
2100
0.09
190
B82144A2152K000
2.2
40
7.96
1900
0.11
140
B82144A2222K000
3.3
40
7.96
1750
0.13
120
B82144A2332K000
4.7
40
7.96
1600
0.16
100
B82144A2472K000
6.8
40
7.96
1500
0.19
80
B82144A2682K000
10
60
2.52
1400
0.22
60
B82144A2103K000
15
60
2.52
1250
0.28
20
B82144A2153K000
22
50
2.52
1100
0.35
12
B82144A2223K000
40
2.52
900
0.43
8.0
B82144A2333J000
47
40
2.52
800
0.50
5.0
B82144A2473J000
68
30
2.52
700
0.60
4.5
B82144A2683J000
100
50
0.796
600
0.70
3.5
B82144A2104J000
150
50
0.796
500
0.90
3.0
B82144A2154J000
220
50
0.796
400
1.60
2.4
B82144A2224J000
330
50
0.796
330
1.90
2.0
B82144A2334J000
470
40
0.796
280
2.50
1.5
B82144A2474J000
680
30
0.796
240
2.80
1.3
B82144A2684J000
1000
60
0.252
200
3.80
1.2
B82144A2105J000
1500
60
0.252
160
6.00
1.0
B82144A2155J000
2200
60
0.252
120
9.00
0.8
B82144A2225J000
3300
60
0.252
110
12.0
0.6
B82144A2335J000
4700
60
0.252
90
20.0
0.5
B82144A2475J000
6800
60
0.252
80
30.0
0.4
B82144A2685J000
10000
50
0.0796
60
42.0
0.35
B82144A2106J000
15000
50
0.0796
50
68.0
0.30
B82144A2156J000
22000
50
0.0796
40
120
0.26
B82144A2226J000
33000
50
0.0796
35
150
0.22
B82144A2336J000
47000
40
0.0796
30
230
0.18
B82144A2476J000
68000
40
0.0796
25
290
0.15
B82144A2686J000
100000
30
0.0796
20
420
0.12
B82144A2107J000
μH
1.0
33
±10%
±5%
^
^
J
K
1) Closer tolerances on request.
2) For Ammo pack the last digit has to be a »9«. Example: B82144A2102K009
Please read Cautions and warnings and
Important notes at the end of this document.
5
03/08
RF chokes
B82144A
LBC series, 5.2 s 12 (mm)
Characteristics and ordering codes
LR
Tolerance
Qmin
μH
fQ
IR
Rmax
fres,min
MHz
mA
Ω
MHz
Ordering code
(reel packing) 1)
For telecommunications in the blocking filter for 12-kHz and 16-kHz counting pulses
980
±3%
25
0.016
200
3.8
1.2
B82144A2984A000
1450
25
0.016
140
6.0
1.0
B82144A2145A500
2600
20
0.012
120
11.0
0.7
B82144A2265A000
3050
25
0.016
100
12.0
0.6
B82144A2305A500
5330
20
0.012
90
25.0
0.5
B82144A2535A300
^
A
1) For Ammo pack the last digit has to be a »9«. Example: B82144A2336J009
Please read Cautions and warnings and
Important notes at the end of this document.
6
03/08
RF chokes
B82144A
LBC series, 5.2 s 12 (mm)
Impedance |Z| versus frequency f
measured with impedance analyzer Agilent
4294A or S-parameter network analyzer
Agilent 8753ES, typical values at 20 °C
Inductance L versus DC load current IDC
measured with LCR meter Agilent 4284A,
typical values at 20 °C
IND0131-7
10 7
Ω
B82144A
100000 µH
10000 µH
|Z| 10 6
100 µH
100000 µH
10 µH
B82144A
10000 µH
L 10 4
1000 µH
10 5
IND0132-9
10 5
µH
1000 µH
10 3
1 µH
10 4
100 µH
10 2
10 3
10 2
10
10 µH
10 1
1 µH
10 0
1
10 0 5
10
10
6
10
7
10
8
Hz 10
10
9
_1
10
_2
10
_1
10 0
f
Current derating Iop/IR
versus ambient temperature TA
(rated temperature TR = 40 °C)
Q factor versus frequency f
measured with impedance analyzer
Agilent 4294A, typical values at 20 °C
IND0133-R
200
IND0552-S-E
1.2
B82144A
Iop
IR
Q
100000 µH
10000 µH
1000 µH
100 µH
10 µH
1 µH
100
A 10 1
I DC
1.0
0.8
0.6
0.4
0.2
0 4
10
10 5
10 6
10 7
0
Hz 10 8
0
20
40
60
80
100
˚C
TA
f
7
03/08
140
Cautions and warnings
■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and
Important notes at the end of this document.
8
03/08
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with
them than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue,
MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are
trademarks registered or pending in Europe and in other countries. Further information will be
found on the Internet at www.epcos.com/trademarks.
9
03/09
Similar pages