JDS ACC703-000 10/100/1000mb/s ethernet demarcation device. Datasheet

COMMUNICATIONS TEST & MEASUREMENT SOLUTIONS
EtherNID GE
Ethernet Services Demarcation Point
Key features
The growing demand for Ethernet Services is exploding
everywhere.
Carriers contending in this competitive market space are faced with several
challenges:
• Setting a clear Demarcation Point between the Customers' and
the Carriers' Ethernet Network
• Implementing Operations, Administration and Maintenance
(OAM), to reduce OPEX and minimize truck-roll
• Assuring End-to-End Service Level Agreement (SLA) parameters
• Offering Carrier-Grade Reliability
All of this while avoiding any impact on network performance and
keeping CAPEX at a minimum
The Accedian EtherNID™ GE Ethernet Demarcation Device (EDD) offers the solution to these
challenges by implementing standards-based OAM and loop-back capabilities. Providing a Performance Assurance Agent™ (PAA™) allows measuring and tracking End-to-End SLA parameters
such as Latency, Jitter, Packet Loss and Availability in a continuous manner, while the service is running.
The EtherNID™ GE can also be used as a last-mile delivery vehicle by providing an optical or electrical port extension to Metro Ethernet Access Platforms.With 2 SFP receptacles, and 2 tri-rate RJ-45s,
the EtherNID™ GE's Universal Architecture allows the user to mix and match medias and upgrade
last-mile fiber from 100M to GigE with no truck-roll.
Furthermore, the EtherNID™ GE's high-performance Fast-Thru™ engine minimizes intrinsic
packet-jitter and latency of the device (0.6 microsecond), thus allowing the deployment of multiple
units along an End-to-End Ethernet Service Path without introducing any significant latency or
jitter to the service itself.
The EtherNID™ GE's ports can also be configured for Monitoring where external test devices can be
connected to perform non-intrusive, in-service troubleshooting, thus offering Layer 1 to 4 visibility
in each direction independently or combined, a function that carriers are used-to with traditional
demarcation devices but lacking from current Ethernet service delivery methods. Furthermore,
intelligent wire-speed filters can be applied to selectively monitor specific traffic.
Additionally, the EtherNID™ GE can be optionally line-powered using Power over Ethernet (PoE)
and offers a fail-over bypass circuitry (electrical) for added reliability.
The EtherNID™ GE interacts seamlessly with Ethernet OAM compliant devices, supports SNMP,
comes with an embedded Web GUI and can be optionally managed via a Management VLAN.
Designed very cost effectively for volume deployment, the EtherNID™ GE unlocks the businesscase for High-Performance, manageable Metro Ethernet service delivery in the last-mile.
WEBSITE: www.jdsu.com
ETHERNID GE
2
Features and Benefits
Ethernet OAM & loop-backs
Better visibility, easier maintenance, reduced truck-rolls
Dual Tap/Monitoring ports
Allows non-intrusive Monitoring Access to live traffic, avoids chasing “ghosts”
Traffic Filtering/Policing
Allows blocking unwanted traffic types (e.g. BPDU/STP/L2CP) and controlling which VLANs
are allowed
Per-Flow Statistics
Allows tracking bandwidth utilization of every stream/EVC delivered
ETHERNID GE
3
Applications
• Customer Premises Located Intelligent Ethernet Demarcation Device
• Inter-Carrier Handoff Demarcation
• End-to-End SLA-Meter™
• Intelligent extension to Metro Access Platforms
• Intelligent Ethernet Optical Repeater (SFP to SFP)
• Wire-speed Remote Loop-back responder to Portable or Centralized Ethernet Test-sets
• Intelligent Wire-speed Ethernet Monitor/Tap troubleshooting device
Multi-carrier Performance Assurance Agent™ (PAA™) Application
• Assures in-service , End-to-End SLA across Multi-Vendor/Multi-Carrier and Layer 1-2-3
networks
Business Multi-Tenant Building Application
NID
Accedian
EtherNID™
CPE
Customer
Provided
Equipment
ETHERNID GE
4
Specifications
Network-side interface
10/100/1000BaseTX/FX/LX/SX
(depends if SFP is used)
Connector: SFP module or RJ-45
(Auto-negotiation/Auto MDIX)
Client-side interface
10/100/1000BaseTX/FX/LX/SX
(depends if SFP is used)
Connector: SFP module or RJ-45
(Auto-negotiation/Auto MDIX)
NID features
IEEE 802.3ah Ethernet OAM
Implements a Two-Port MAC Relay (TPMR)
function aligned with IEEE's 802.1aj, 802.1ad,
and 802.1ag/ITU-T Y.1731 drafts
Loop-backs:
– Layer 1, Layer 2 (MAC Swap), Layer 3 (IP
Swap), Layer 4 (TCP/UDP Port Swap)
– Automatically reacts to in-band loop-back
commands of industry-popular Ethernet testsets
– Individual VLAN loop-backs
– Loop-back on specific MAC source and/or
destination address
– Loop-back on specific IP source and/or destination address
Thru-Traffic Per-flow statistics (per VLAN, per
Ethertype, per ToS, per CoS, per MAC, per IP,
etc.)
VLAN Tagging/De-tagging
VLAN Stacking (.1Q in .1Q)
Through Traffic Wire-Speed Filtering (L2CP,
BPDU, per-VLAN, Ethertype, Protocol type,MAC,
IP,User Defined)
Dual Monitor Access Ports providing individual
access to both signal directions, combined
access to both directions, Layer 1 tapping and
intelligent filtering
Integrated Copper TDR cable integrity testing
Dying Gasp (via 802.3ah or SNMP traps)
Supports packet sizes up to 1800 bytes
Fault Propagation
Link Loss Return
Performance Assurance Agent™ (PAA™)
Constant in-service monitoring of SLA parameters including:
Packet loss
– Two-way delay (Round-trip Latency)
– Two-way delay variation (Round-trip Jitter)
– One-way delay variation (One-way Jitter)
– Continuous End-to-End path Continuity
Check
High Precision measurements: 1 microsecond
accuracy
Management
In-band remote management over the
Ethernet customer line via Network-side interface
Local Management craft port: 10/100BaseT,
RJ-45 connector
Serial RS-232 Management port: RJ-45 connector
Secure Web GUI via SSL
Secure CLI command prompt via SSH
Works at Layer 2 and Layer 3
SNMP V1,V2C
Assures SLAs per VLAN/per CoS/per ToS/per
EVC
Management VLAN
Can work in point-to-point or point-to-multipoint
NTP client
Multiple Instance capable (Multi-SLA™)
User settable SLA threshold crossing alerts
using SNMP traps
Inline transparent performance
Throughput: wire-speed (100Mb/s at 100%
utilization)
802.3ah EFM OAM
Remote and Local Syslog
Radius Authentication
DNS Client
DHCP Client
Config. import/export
FTP,TFTP, SFTP, HTTP
Intrinsic Passthrough Traffic Latency: <8 microsecond (at all packet sizes)
Power options all included as standard
and redundant between each other
Intrinsic Passthrough Traffic Jitter: <1 microsecond (at all packet sizes)
External AC/DC adapter (120-240 Vac autosensing, 50-60 Hz), 5 Vdc input to unit
Intrinsic Latency for Intelligent Loopback: <8
microsecond (at all packet sizes)
Dual (A/B) -48 Vdc Central Office Supply inputs
Intrinsic Jitter for Intelligent Loopback: <1
microsecond (at all packet sizes)
Power Consumption: 5 watts
Optional Network-Client Power Fail-over
bypass mode
PoE from RJ-45 (802.3af )
Cooling: convection cooled (no fans)
Regulatory
Physical
1.60" H x 5.34" W x 5.80" D
Mounting:
– Desktop
– Wall-mount
– Rack-mount (2 units side-by-side in 1U)
– 12 position, high-density, 19” central office
shelf (4U): EtherSHELF™
IEC 60950
FCC Part 15 Class A
Industry Canada CS-03
CE Mark
Operating Temperature
0-50 degree C
Storage Temperature
-40 to 70 degree C
Humidity
5-95% non-condensing
ETHERNID GE
Model number
Product name
Description
ACC703-000
EtherNID™ GE
10/100/1000Mb/s Ethernet Demarcation Device.
SFP modules
EtherNID GE
ACC7SM-000
SFP 1000Mb/s MM
1000Mb/s SFP module for use with EtherNID™ GE, MM,
850 nm, VCSEL, 550 m, LC connector.
ACC7SN-000
SFP 1000Mb/s 10 km
1000Mb/s SFP module for use with EtherNID™ GE, SM,
1310 nm, FP, 10 km, LC connector.
ACC7SO-000
SFP 1000Mb/s 30 km
1000Mb/s SFP module for use with EtherNID™ GE, SM,
1310 nm, DFB, 30 km, LC connector.
ACC7SP-000
SFP 1000Mb/s 50 km
1000Mb/s SFP module for use with EtherNID™ GE, SM,
1550 nm, DFB, 50 km, LC connector.
ACC7SA-000
SFP 100Mb/s 16 DB
100Mb/s SFP module for use with EtherNID™ OE, SM,
1310 nm, FP, 16 dB budget, LC connector.
ACC7SB-000
SFP 100Mb/s 30 DB
100Mb/s SFP module for use with EtherNID™ OE, SM,
1310 nm, FP 30 dB budget, LC connector.
ACC704-000
EtherSHELF™
Rackmount 4U Vertical Mounting Shelf, fits 12 EtherNID™
units individually fused, -48V (A/B) redundant power feeds,
can mix and match EE, OE, and GE models.
ACC706-000
2 Unit Rackmount
Bracket
Rackmount 1U Horizontal Mounting Bracket, fits 2
EtherNID™ units.
ACC705-000
1 Unit Rackmount
Bracket
Rackmount 1U Horizontal Mounting Bracket, fits 1
EtherNID™ unit.
Accessories
EtherNID EE
Related products
EtherNID OE
Test & Measurement Regional Sales
ACC701-000
EtherNID™ EE
10/100Mb/s Electrical-to-Electrical Ethernet Demarcation
Device.
ACC702-000
EtherNID™ OE
10/100Mb/s Optical to Electrical Ethernet Demarcation
Device.
All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and
no responsibility is assumed for any inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its applications. JDSU reserves the right to change at any time without notice
the design, specifications, function, fit or form of its products described herein, including withdrawal at any
time of a product offered for sale herein. JDSU makes no representations that the products herein are free from
any intellectual property claims of others. Please contact JDSU for more information. JDSU and the JDSU logo
are trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders.
© 2006 JDS Uniphase Corporation. All rights reserved. 30149052 001 0707 ETHERNIDEE.DS.CPO.TM.AE
NORTH AMERICA
LATIN AMERICA
ASIA PACIFIC
TEL: 1 866 228 3762
FAX: +1 301 353 9216
TEL:+55 11 5503 3800
FAX:+55 11 5505 1598
TEL:+852 2892 0990
FAX:+852 2892 0770
EMEA
TEL:+49 7121 86 2222
FAX:+49 7121 86 1222
WEBSITE: www.jdsu.com
Similar pages