7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 REVISION 2266045 -1 DESCRIPTION F 2266045 -2 FINE CRIMP HEIGHT ADJUST F 2266045 -5 SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 12 F NON-CRIMP HEIGHT ADJUST 2266045 -7 F FINE CRIMP HEIGHT ADJUST B PNEUMATIC FEED SERVO LATCH PLATE 2266045 -6 7- 2266045 -7 CONVERT TO MECHANICAL FINE CRIMP HEIGHT ADJUST F APPLICATOR STYLE CONVERSION CHART FEED TYPE 4 NONE CRIMP TOOLING KIT - 4 PNEUMATIC FEED - - - - CRIMP 2119950-1 1338685-1 2161326-1 - 2119951-1 - 2119949-1 1338685-1 2119951-1 - 2161326-1 - 2119949-1 1338685-1 2119950-1 5-18022-5 8- 2266045 -5 8- 2266045 -4 5-18022-5 8- 2266045 -5 8- 2266045 -4 5-18022-5 1338685-1 - 5-18022-5 - - - - - 1901094-3 - 2119653-1 1901094-3 - 2119653-1 2119641-1 - - - 2119641-1 - - - - - - - 2119799-1 WIRE INSUL 1-1752354-2 - 1-1752354-2 - 2168400-6 2168400-6 - 2119799-1 - - - (QUANTITY 2) - - - - - (QUANTITY 2) - - - - - 2063440-1 - - - - 6 - - - - TYPE 8 F - 0.80 mm [.031] - APPLICATOR INSTRUCTIONS 408-10389 - - - TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION WIRE STRIP LENGTH 2.86-3.80 mm [.113-.150 IN] C TERMINAL APPLICATION SPECIFICATION n 114-32145 - TERMINALS APPLIED TE TERMINAL 2203260-2 - CENTER CONTACT, 180 DEGREE, FAKRA TERMINAL NAME: C1__DWG_PN_1_0 C1__DWG_PN_1_1 13 INSULATION DIAMETER RANGE - 1.49-1.65 mm [.059-.065 IN] - - - - - - - 13 14 TE TERMINAL 2203270-2 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL - C1__DWG_PN_3_0 C1__DWG_PN_3_1 - TE TERMINAL - 6 C1__DWG_PN_4_0 C1__DWG_PN_4_1 - WIRE SIZE RG-71 U/M RG-62 U/M RG-178 RG-179 1.5C-2VCP B CRIMP HEIGHT mm [INCH] 0.55+/-0.03 [.022+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 0.55+/-0.03 [.022+/-.001] 0.53+/-0.03 [.021+/-.001] 0.53+/-0.03 [.021+/-.001] 0.52+/-0.03 [.020+/-.001] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY 9.2 - 9 - W1__FA_SETTING_1 - 9.2 9.4 - 9.5 - - 9.4 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 6 7 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 7 8 9 10 11 A 12 -4 -4 -5 -6 13 14 - 1 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 252. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 7 TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - 1 1 - -77 -7 1 1 - -6 1 1 - -5 1 1 1 1 -2 - 2119957-2 1803078-4 8-21084-0 2119640-1 1803259-1 -1 PART NO 1 1 - APPLICATOR SHIM PACK SPACER, PRECISION O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, FLANGED DESCRIPTION 1 2119957-2 1 1803078-4 1 8-21084-0_GATD 1 2119640-1 1 1803259-1 260 259 252 250 249 ITEM NO WHEN RUNNING ON A BENCH TERMINATING UNIT TO MAINTAIN PROPER WIRE PLACEMENT, SPLIT CYCLE MODE IS RECOMMENDED FOR THE TERMINATING UNIT. 1 - 1 1 A 1 1 1 1 1 1 1 1 REF 1 1 1 1 1 1 1 2 1 3 1 1 4 1 1 - 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - - 1 66 P LTR 1 - 1 1 1 - 2 2 1 1 1 REF REF REF REF - - - 1 - - 1 - - - - - - 1 -6 1 - - 1 - 1 - - - - 1 - 1 - - - 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 1 1 - 1 1 1 - - 4 1 1 - 1 4 1 - 1 1 4 1 1 1 - 1 1 1 1 4 3 1 - - 1 3 1 1 2 1 3 - 1 2 1 1 1 1 2 - 1 1 - - 1 1 1 2 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 - 1 REF REF 1 - - 1 1 - - 1 1 - 1 REF REF 1 - - 1 -5 -2 mm MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - RS LZ E ECR-16-011816 29AUG2016 JH TE F ECR-16-018246 30DEC2016 TB CT FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, STEPPED, ATLANTIC, SF, NON-ADJ SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF ASSY, LUBRICATOR, SIDE FEED SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, STEPPED, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 40) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED SPRING, COMPRESSION STOP, SHEAR HOLDER, SHEAR SHEAR, FLOATING ANVIL, COMBINATION DEPRESSOR, SHEAR CRIMPER, WIRE F DWN 24OCT2013 CHK 25OCT2013 APVD 25OCT2013 R.O.WILSON K.J.STAKEM T.L.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 1-22279-3_SIMP 1 2161314 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 1 1-1752354-2 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 2119955-1 1 1-455888-7 1 SIMP_5-547505-2 1 854769-8 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 21028-2 1 1338685-1 4 2168400-1 1 1-5018030-0 1 1-1901681-9 3 18023-9 1 2119652 1 2119653 1 2119656-9 1 2161311 1 1-2079383-5 1 2119645 1 2119957-1 1 1-2119644-4 1 2119085_PRE_REV_K 1 2119092-1 1 1752356-5 2 2079383-5 1 2161328 1 1320908-8 1 2119959-1 1 1-455888-0 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533-2 1 SIMP_3-22280-3 1 356885-5 1 1552193-1 1 1803251 1 5-1633933-8 .. 1 ITEM_7 .. 1 ITEM_6 1 1803349-4 .. 1 ITEM_4 .. 1 ITEM_3 .. 1 ITEM_2 1 2-1803241-5 248 247 246 245 240 239 238 213 198 180 177 176 175 174 172 166 164 163 137 136 135 133 119 117 113 82 77 74 71 67 66 63 62 60 59 58 56 54 52 51 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 24 21 20 19 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119798-1 TE Connectivity APPLICATION SPEC - 1 2119641-1 DESCRIPTION PRODUCT SPEC - APVD 19JUL2016 PART NO - DWN ECR-16-010040 -1 1 DATE D1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 - - 1 1 1 1 1 1 - - - 1 - - - - 1 - 2 - 1 1 DESCRIPTION 2119641-1 2119798-1 1-22279-3 2161314-1 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 1-1752354-2 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 2119955-1 1-455888-7 5-547505-2 854769-8 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 21028-2 1338685-1 2168400-1 1-5018030-0 1-1901681-9 18023-9 2119652-1 2119653-1 2119656-9 2161311-1 1-2079383-5 2119645-1 2119957-1 1-2119644-4 2119085-1 2119092-1 1752356-5 2079383-5 2161328-1 1320908-8 2119959-1 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-2 3-22280-3 356885-5 1552193-1 1803251-1 5-1633933-8 1803349-4 2-1803241-5 - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: & 4 of 4) - -77 -7 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 - - 5.25 . TERMINAL LUBRICANT IS RECOMMENDED. AMP 4805 REV 31MAR2000 - - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62& 180. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37 & 180. WHEN ASSEMBLING A NON CRIMP HEIGHT ADJUST APPLICATOR (-6) USE SHIMS FROM ITEM 260 TO ACHIEVE A NOMINAL SHIM HEIGHT OF - - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 - 2266045 2266045 2266045 2266045 REVISIONS DIST 2063440-1 - SIZE 1 PART NUMBERS REQUIRED - APPLICATOR DATA LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER D 6 Ocean Side Feed Applicator - DRAWING NO 2266045 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV F D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE MECHANICAL D 239 38 56 39 2 247 246 260 44 7 252 245 7 249 63 A 166 D 2 2 2 2 8 8 163 259 59 82 136 1 137 TERMINAL SUPPORT LOCATION 177 SERVO LATCH PLATE 2 2 135 28 5 41 174 44 175 245 REF 51 6 164 A 17.8 66 180 2 33 SERVO FEEDER NOT INCLUDED 117 REF 10 A 77 58 30 20 29 21 B 1 ITEM 30 LOCATED AT FRONT HOLES 12 30 REF 29 REF CAM POSITIONS 11 30mm STROKE 30mm STROKE 119 113 13 46 32 34 54 8 1 60 54 10 1 FEED TRACK POSITION GUIDE BY WIRE BARREL 248 48 180 REF HOLDDOWN SET-UP 74 19 9 47 0.5 67 11 213 24 30mm STROKE REF 52 198 B 0.5 34 REF 2 176 4 4.3 C 56 133 REF 1 172 240 - 35 238 C - - 40 59 250 APVD 62 6 PNEUMATIC DWN 37 6 A DATE A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24OCT2013 CHK 25OCT2013 APVD 25OCT2013 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266045 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER REVISION 2- 2266045 -1 DESCRIPTION F 2- 2266045 -2 D 6 FEED TYPE FINE CRIMP HEIGHT ADJUST F FINE CRIMP HEIGHT ADJUST F FINE CRIMP HEIGHT ADJUST 2- 2266045 -7 F FINE CRIMP HEIGHT ADJUST NONE CRIMP TOOLING KIT PNEUMATIC FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED SERVO LATCH PLATE PNEUMATIC 2- 2266045 -5 B CONVERT TO MECHANICAL SERVO LATCH PLATE 7- 2266045 -7 APPLICATOR STYLE CONVERSION CHART - SMART APPLICATOR MECHANICAL FEED 4 PNEUMATIC FEED - - CRIMP WIRE INSUL 2119950-1 1338685-1 2161326-1 - 2119951-1 2119949-1 2119951-1 2161326-1 2119949-1 2119950-1 - - 5-18022-5 - 8- 2266045 -5 8- 2266045 -4 1338685-1 5-18022-5 - 8- 2266045 -5 - 8- 2266045 -4 1338685-1 5-18022-5 1338685-1 5-18022-5 - - - - 2119641-2 1901094-3 - 2119653-2 1901094-3 - 2119653-2 2119641-2 - - 2119799-1 1-1752354-2 - - 1-1752354-2 - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) - - - - - (QUANTITY 2) - - - - - 2063440-1 - - - 6 - - - APPLICATOR INSTRUCTIONS 408-10389 - 8 F - - - - - 7 - TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION WIRE STRIP LENGTH 2.86-3.80 mm [.113-.150 IN] C TERMINAL APPLICATION SPECIFICATION 2203260-2 n 114-32145 - TERMINALS APPLIED TE TERMINAL - CENTER CONTACT, 180 DEGREE, FAKRA TERMINAL NAME: C1__DWG_PN_1_0 C1__DWG_PN_1_1 12 - 7 INSULATION DIAMETER RANGE - 1.49-1.65 mm [.059-.065 IN] - - - - - - - 13 TE TERMINAL 2203270-2 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 C1__DWG_PN_3_0 - TE TERMINAL - 12 C1__DWG_PN_4_0 - C1__DWG_PN_3_1 - C1__DWG_PN_4_1 - WIRE SIZE RG-71 U/M RG-62 U/M RG-178 RG-179 1.5C-2VCP 1 B 2 CRIMP HEIGHT mm [INCH] 0.55+/-0.03 [.022+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 0.55+/-0.03 [.022+/-.001] 0.53+/-0.03 [.021+/-.001] 0.53+/-0.03 [.021+/-.001] 0.52+/-0.03 [.020+/-.001] 9.2 - 9 - 6 W1__FA_SETTING_1 - 9.2 - 9.4 - 9.4 - 9.5 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS - GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- - 2266045 -4 2266045 -4 2266045 -5 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62 & 180. 7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 & 152. 1 MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 9 10 11 A 12 13 - 1 6 8 - 1 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - TERMINAL LUBRICANT IS RECOMMENDED. WHEN RUNNING ON A BENCH TERMINATING UNIT TO MAINTAIN PROPER WIRE PLACEMENT, SPLIT CYCLE MODE IS RECOMMENDED FOR THE TERMINATING UNIT. AMP 4805 REV 31MAR2000 66 P LTR DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 2063440-1 TYPE 0.80 mm [.031] A PART NUMBERS REQUIRED - SIZE REVISIONS DIST - - APPLICATOR DATA LOC 1 - 1 1 - 1 1 - 1 1 1 1 1 - -77 -27 -25 -22 -21 1803078-4 2119782-1 2119640-1 PART NO SPACER, PRECISION FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED DESCRIPTION 1 1803078-4 1 2119782 1 2119640-1 - 259 251 250 - ITEM NO 1 1 1 - 1 2 - 1 2 1 REF 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 - - 1 1 1 1 1 - - - - - 1 - - 1803259-1 1-22279-3 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 1-1752354-2 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 1-2119656-0 2161312-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 2119955-1 1-455888-7 5-547505-2 854769-8 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 21028-2 1338685-1 1-5018030-0 1-1901681-9 18023-9 2119652-1 1-2079383-5 2119645-1 2119957-1 1-2119644-4 1752356-5 2079383-5 2161328-1 1320908-8 2119959-1 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-2 3-22280-3 356885-5 1552193-1 1803251-1 5-1633933-8 1803349-4 2-1803241-5 - - 1 1 REF REF REF - - 1 1 1 - 1 - 1 - - - 1 1 - - - - 1 - - - - 1 - 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 - 1 3 1 1 - 1 3 - 1 2 1 3 - 1 2 1 3 1 1 2 1 1 1 - 2 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 - 1 REF 1 - - 1 - - - 1 1 - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - - - 1 - 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 2 of 4) - MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - BUSHING, FLANGED SPRING, COMPRESSION SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, STEPPED, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF ASSY, LUBRICATOR, SIDE FEED SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 40) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED SPRING, COMPRESSION STOP, SHEAR HOLDER, SHEAR SHEAR, FLOATING ANVIL, COMBINATION DEPRESSOR, SHEAR CRIMPER, WIRE F PART NO -77 -27 -25 -22 -21 PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 1 1 - DWN 24OCT2013 CHK 25OCT2013 APVD 25OCT2013 R.O.WILSON K.J.STAKEM T.L.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 1 1-1752354-2 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 1-2119656-0 1 2161312 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 2119955-1 1 1-455888-7 1 SIMP_5-547505-2 1 854769-8 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 21028-2 1 1338685-1 1 1-5018030-0 1 1-1901681-9 3 18023-9 1 2119652 1 1-2079383-5 1 2119645 1 2119957-1 1 1-2119644-4 1 1752356-5 2 2079383-5 1 2161328 1 1320908-8 1 2119959-1 1 1-455888-0 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533-2 1 SIMP_3-22280-3 1 356885-5 1 1552193-1 1 1803251 1 5-1633933-8 .. 1 ITEM_7 .. 1 ITEM_6 1 1803349-4 .. 1 ITEM_4 .. 1 ITEM_3 .. 1 ITEM_2 1 2-1803241-5 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 2 2168400-6 249 246 240 239 238 213 198 180 177 176 175 174 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 119 117 113 82 77 74 71 67 66 63 62 59 58 56 52 51 49 48 41 40 39 38 34 33 32 30 29 28 24 21 20 19 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 1-22279-3_SIMP DESCRIPTION PRODUCT SPEC - 1 1803259-1 Ocean Side Feed Applicator - DRAWING NO 2266045 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE APVD - - - 62 6 40 A 145 38 239 246 39 59 7 56 140 152 2 D 2 2 7 139 PNEUMATIC 250 8 2 249 166 63 4.3 238 A 163 34 59 259 82 1 137 C 56 2 SERVO LATCH PLATE 2 2 133 4 REF TERMINAL SUPPORT LOCATION 1 C 177 172 240 0.5 REF 8 136 176 28 174 175 135 52 198 51 140 164 A SERVO FEEDER NOT INCLUDED 17.8 11 67 77 213 58 19 10 180 9 29 REF HOLDDOWN SET-UP 74 20 21 117 REF 0.5 2 A 30 REF 66 33 24 5 41 6 180 B DWN 251 MECHANICAL D DATE B 1 12 ITEM 30 LOCATED AT FRONT HOLES CAM POSITIONS 30mm STROKE 30 REF 29 30mm STROKE 30mm STROKE 142 REF 113 151 12 141 32 34 143 8 1 144 143 10 1 119 11 FEED TRACK POSITION GUIDE BY WIRE BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24OCT2013 CHK 25OCT2013 APVD 25OCT2013 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266045 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F