Harris HIN213CA 5v powered rs-232 transmitters/receivers with 0.1microfarad external capacitor Datasheet

S E M I C O N D U C T O R
HIN200 thru HIN213
+5V Powered RS-232 Transmitters/Receivers
with 0.1Microfarad External Capacitors
August 1997
Features
Description
• Meets All RS-232E and V.28 Specifications
The HIN200-HIN213 family of RS-232 transmitters/receivers
interface circuits meet all ElA RS-232E and V.28 specifications,
and are particularly suited for those applications where ±12V is
not available. They require a single +5V power supply (except
HIN201 and HIN209) and feature onboard charge pump voltage converters which generate +10V and -10V supplies from
the 5V supply. The HIN203 and HIN205 require no external
capacitors and are ideally suited for applications where circuit
board space is critical. The family of devices offers a wide variety of RS-232 transmitter/receiver combinations to accommodate various applications (see Selection Table).
• HIN203 and HIN205 Require No External Capacitors
• Requires Only 0.1µF or Greater External Capacitors
• 120kbit/s Data Rate
• Two Receivers Active in Shutdown Mode (HIN213)
• Requires Only Single +5V Power Supply
- (+5V and +12V - HIN201 and HIN209)
• Onboard Voltage Doubler/Inverter
• Low Power Consumption (Typ) . . . . . . . . . . . . . . . 5mA
• Low Power Shutdown Function (Typ) . . . . . . . . . . .1µA
• Three-State TTL/CMOS Receiver Outputs
The HIN200, HIN206, HIN211 and HIN213 feature a low
power shutdown mode to conserve energy in battery
powered applications. In addition, the HIN213 provides two
active receivers in shutdown mode allowing for easy
“wakeup” capability.
• Multiple Drivers
- ±10V Output Swing for +5V lnput
- 300Ω Power-Off Source Impedance
- Output Current Limiting
- TTL/CMOS Compatible
- 30V/µs Maximum Slew Rate
The drivers feature true TTL/CMOS input compatibility, slew
rate-limited output, and 300Ω power-off source impedance.
The receivers can handle up to ±30V input, and have a 3kΩ
to 7kΩ input impedance. The receivers also feature hysteresis to greatly improve noise rejection.
• Multiple Receivers
- ±30V Input Voltage Range
- 3kΩ to 7kΩ Input Impedance
- 0.5V Hysteresis to Improve Noise Rejection
• Any System Requiring RS-232 Communications Port
- Computer - Portable, Mainframe, Laptop
- Peripheral - Printers and Terminals
- Instrumentation
- Modems
Applications
Selection Table
POWER SUPPLY
VOLTAGE
NUMBER OF
RS-232
DRIVERS
NUMBER OF
RS-232
RECEIVERS
NUMBER OF
0.1µF
EXTERNAL
CAPACITORS
LOW POWER
SHUTDOWN/TTL
THREE-STATE
NUMBER OF
RECEIVERS
ACTIVE IN
SHUTDOWN
HIN200
+5V
5
0
4 Capacitors
Yes/No
0
HIN201
+5V and +9V to 13.2V
2
2
2 Capacitors
No/No
0
HIN202
+5V
2
2
4 Capacitors
No/No
0
HIN203
+5V
2
2
None
No/No
0
HIN204
+5V
4
0
4 Capacitors
No/No
0
HIN205
+5V
5
5
None
Yes/Yes
0
HIN206
+5V
4
3
4 Capacitors
Yes/Yes
0
HIN207
+5V
5
3
4 Capacitors
No/No
0
PART
NUMBER
HIN208
5V
4
4
4 Capacitors
No/No
0
HIN209
+5V and +9V to 13.2V
3
5
2 Capacitors
No/Yes
0
HIN211
+5V
4
5
4 Capacitors
Yes/Yes
0
HIN213
+5V
4
5
4 Capacitors
Yes/Yes
2
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright
© Harris Corporation 1997
8-3
File Number
3980.6
HIN200 thru HIN213
Ordering Information
PART NO.
TEMP.
RANGE (oC)
PACKAGE
PKG. NO.
PART NO.
TEMP.
RANGE (oC)
PACKAGE
PKG. NO.
HIN200CB
0 to 70
20 Ld SOIC
M20.3
HIN207CB
0 to 70
24 Ld SOIC
M24.3
HIN200IB
-40 to 85
20 Ld SOIC
M20.3
HIN207CA
0 to 70
24 Ld SSOP
M24.209
HIN201CB
0 to 70
16 Ld SOIC (W)
M16.3
HIN207IP
-40 to 85
24 Ld PDIP (N)
E24.3
HIN201IB
-40 to 85
16 Ld SOIC (W)
M16.3
HIN207IB
-40 to 85
24 Ld SOIC
M24.3
HIN202CP
0 to 70
16 Ld PDIP
E16.3
HIN207IA
-40 to 85
24 Ld SSOP
M24.209
HIN202CB
0 to 70
16 Ld SOIC (W)
M16.3
HIN208CP
0 to 70
24 Ld PDIP (N)
E24.3
HIN202IP
-40 to 85
16 Ld PDIP
E16.3
HIN208CB
0 to 70
24 Ld SOIC
M24.3
HIN202CA
0 to 70
16 Ld SSOP
M16.209
HIN208CA
0 to 70
24 Ld SSOP
M24.209
HIN202IA
-40 to 85
16 Ld SSOP
M16.209
HIN208IP
-40 to 85
24 Ld PDIP (N)
E24.3
HIN202IB
-40 to 85
16 Ld SOIC (W)
M16.3
HIN208IB
-40 to 85
24 Ld SOIC
M24.3
24 Ld SSOP
M24.209
24 Ld PDIP (N)
E24.3
HIN202CBN
0 to 70
16 Ld SOIC (N)
M16.15
HIN208IA
-40 to 85
HIN202IBN
-40 to 85
16 Ld SOIC (N)
M16.15
HIN209CP
0 to 70
HIN203CP
0 to 70
20 Ld PDIP
E20.3
HIN209CB
0 to 70
24 Ld SOIC
M24.3
HIN203CB
0 to 70
20 Ld SOIC (W)
M20.3
HIN209IP
-40 to 85
24 Ld PDIP (N)
E24.3
HIN204CB
0 to 70
16 Ld SOIC (W)
M16.3
HIN209IB
-40 to 85
24 Ld SOIC
M24.3
HIN204IB
-40 to 85
16 Ld SOIC (W)
M16.3
HIN211CB
0 to 70
28 Ld SOIC
M28.3
HIN205CP
0 to 70
24 Ld PDIP (W)
E24.3
HIN211CA
0 to 70
28 Ld SSOP
M28.209
HIN206CP
0 to 70
24 Ld PDIP (N)
E24.3
HIN211IB
-40 to 85
28 Ld SOIC
M28.3
HIN206CB
0 to 70
24 Ld SOIC
M24.3
HIN211IA
-40 to 85
28 Ld SSOP
M28.209
HIN206CA
0 to 70
24 Ld SSOP
M24.209
HIN213CB
0 to 70
28 Ld SOIC
M28.3
HIN206IP
-40 to 85
24 Ld PDIP (N)
E24.3
HIN213CA
0 to 70
28 Ld SSOP
M28.209
HIN206IB
-40 to 85
24 Ld SOIC
M24.3
HIN213IB
-40 to 85
28 Ld SOIC
M28.3
HIN206IA
-40 to 85
24 Ld SSOP
M24.209
HIN213IA
-40 to 85
28 Ld SSOP
M28.209
HIN207CP
0 to 70
24 Ld PDIP (N)
E24.3
Pin Descriptions
PIN
VCC
FUNCTION
Power Supply Input 5V ±10%, 5V ±5% (HIN200, HIN207, HIN203, and HIN205).
V+
Internally generated positive supply (+10V nominal), HIN201 and HIN209 requires +9V to +13.2V.
V-
Internally generated negative supply (-10V nominal).
GND
Ground lead. Connect to 0V.
C1+
External capacitor (+ terminal) is connected to this lead.
C1-
External capacitor (- terminal) is connected to this lead.
C2+
External capacitor (+ terminal) is connected to this lead.
C2-
External capacitor (- terminal) is connected to this lead.
TIN
Transmitter Inputs. These leads accept TTL/CMOS levels. An internal 400kΩ pull-up resistor to VCC is connected to each lead.
TOUT
RIN
ROUT
Transmitter Outputs. These are RS-232 levels (nominally ±10V).
Receiver Inputs. These inputs accept RS-232 input levels. An internal 5kΩ pull-down resistor to GND is connected to each input.
Receiver Outputs. These are TTL/CMOS levels.
EN, EN
Enable input. This is an active low input which enables the receiver outputs. With EN = 5V, (HIN213 EN = 0V), the outputs
are placed in a high impedance state.
SD, SD
Shutdown Input. With SD = 5V (HIN213 SD = 0V), the charge pump is disabled, the receiver outputs are in a high impedance
state (except R4 and R5 of HIN213) and the transmitters are shut off.
NC
No Connect. No connections are made to these leads.
8-4
HIN200 thru HIN213
Pinouts
HIN200 (SOIC)
TOP VIEW
HIN201 (SOIC)
TOP VIEW
T3OUT
1
20 T4OUT
C+
1
16 V+
T1OUT
2
19 T5IN
C-
2
15 VCC
T2OUT
3
18 NC
V-
3
14 GND
T2IN
4
17 SD
T1IN
5
16 T5OUT
GND
6
15 T4IN
VCC
7
14 T3IN
C1+
8
13 V-
V+
9
12 C2-
C1- 10
11 C2+
R2IN
5
12 R1IN
R2OUT
6
11 R1OUT
T2IN
7
10 T1IN
NC
8
9 NC
+5V
+5V
7
8
0.1µF
0.1µF
T1IN
T2IN
T3IN
+
10
C111
C2+
+
12
C25
VCC
C1+
+5V TO 10V
VOLTAGE DOUBLER
+10V TO -10V
VOLTAGE INVERTER
+5V
400kΩ
4
+5V
400kΩ
14
+5V
400kΩ
V+
9
+
VCC
0.1µF
V- 13
2
+
2
0.1µF
T1OUT
T1IN
T2OUT
T2IN
T3
1
T3OUT
R1OUT
C+
C-
T5IN
15
19
+5V
400kΩ
+5V
400kΩ
16
V- 3
+
+5V
400kΩ
T1
+5V
400kΩ
T2
7
13
4
11
0.1µF
T1OUT
T2OUT
12
R1IN
5kΩ
R1
T4IN
V+
+12V TO -12V
VOLTAGE INVERTER
10
T2
3
+9V TO +13.2V
15
0.1µF
1
+
T1
13 T1OUT
T2OUT 4
T4
20
T4OUT
R2OUT
6
5
5kΩ
R2
T5
16
17
GND
T5OUT
GND
SD
14
6
8-5
R2IN
HIN200 thru HIN213
Pinouts
(Continued)
HIN202 (PDIP, SOIC, SSOP)
TOP VIEW
HIN203 (PDIP, SOIC)
TOP VIEW
C1+ 1
16 VCC
T2IN
1
V+ 2
15 GND
T1IN
2
19 R2IN
R1OUT
3
18 T2OUT
C1- 3
14 T1OUT
C2+ 4
13 R1IN
12 R1OUT
C2- 5
6
11 T1IN
T2OUT 7
10 T2IN
V-
9 R2OUT
R2IN 8
20 R2OUT
R1IN
4
17 V-
T1OUT
5
16 C2-
GND
6
15 C2+
VCC
7
14 V+ (C1-)
(V+) C1+
8
13 C1- (C1+)
GND
9
12 V- (C2+)
(V-) C2- 10
11 C2+ (C2-)
NOTE: Pin numbers in parentheses are for SOIC Package.
+5V
+5V
+
16
1
0.1µF
+
3
4
0.1µF
T1IN
T2IN
+
5
11
10
VCC
C1+
C1C2+
C2-
+10V TO -10V
VOLTAGE INVERTER
+5V
400kΩ
V+
2
+
0.1µF
T1IN
2
400kΩ
+5V
T2IN
V- 6
+
1
400kΩ
T1
5
T2
18
3
0.1µF
4
R1OUT
T1OUT
T2OUT
R1IN
5kΩ
T1
14
T1OUT
R2OUT
7
T2OUT
R2IN
NO 13 (14)
CONNECT
13
INTERNAL
-10V
SUPPLY
INTERNAL
+10V
SUPPLY
R1IN
R1OUT
5kΩ
R1
9
8
R2IN
12 (10)
17
14 (8)
5kΩ
C1+
C1-
GND
15
8-6
11 (12)
15
16
V-
C2-
VV+
C2+
C2+
C2GND
6
5kΩ
R2
19
20
8 (13)
T2
12
R2OUT
VCC
+5V
+5V TO 10V
VOLTAGE INVERTER
+5V
400kΩ
0.1µF
6
GND
9
10 (11)
HIN200 thru HIN213
Pinouts
(Continued)
HIN204 (SOIC)
TOP VIEW
HIN205 (PDIP)
TOP VIEW
T1OUT 1
16 T3OUT
T4OUT 1
24 R3IN
T2OUT 2
15 T4OUT
T3OUT 2
23 R3OUT
14 T4IN
T1OUT 3
22 T5IN
T2OUT 4
21 SD
R2IN 5
20 EN
T2IN 3
T1IN 4
13 T3IN
GND 5
12 V-
VCC 6
11 C2-
C1+ 7
10 C2+
V+ 8
9 C1-
19 T5OUT
R2OUT 6
T2IN 7
18 R4IN
T1IN 8
17 R4OUT
R1OUT 9
16 T4IN
R1IN 10
15 T3IN
GND 11
14 R5OUT
VCC 12
13 R5IN
+5V
+5V
12
VCC
+5V
6
7
0.1µF
0.1µF
T1IN
T2IN
+
9
VCC
C1+
C1-
10
C2+
+
11
C2-
+5V TO 10V
VOLTAGE DOUBLER
+10V TO -10V
VOLTAGE INVERTER
V+
8
+
+5V
400kΩ
T1
T2
3
+5V
400kΩ
T1IN
T2IN
V- 12
+
4
0.1µF
1
2
T3IN
0.1µF
T4IN
T1OUT
T5IN
T2OUT
R1OUT
T3IN
T4IN
+5V
400kΩ
13
14
T1
8
400kΩ
7
+5V
400kΩ
T2
15
+5V
400kΩ
T3
16
+5V
400kΩ
T4
22
+5V
400kΩ
T5
3
4
2
1
19
10
9
16
T3OUT
15
5
6
T4
23
T3OUT
T4OUT
T5OUT
R1IN
R2IN
R3IN
GND
5kΩ
R3
17
18
R4OUT
R4IN
5kΩ
R4
14
13
R5OUT
R5IN
20
5kΩ
R5
21
EN
SD
GND
11
8-7
T2OUT
24
R3OUT
5
T1OUT
5kΩ
R2
T4OUT
0.1µF
5kΩ
R1
T3
R2OUT
+5V
400kΩ
+
HIN200 thru HIN213
Pinouts
(Continued)
HIN206 (PDIP, SOIC, SSOP)
TOP VIEW
HIN207 (PDIP, SOIC, SSOP)
TOP VIEW
T3OUT
1
24 T4OUT
T3OUT 1
24 T4OUT
T1OUT
2
23 R2IN
T1OUT 2
23 R2IN
T2OUT
3
22 R2OUT
T2OUT 3
22 R2OUT
R1IN
4
21 SD
R1IN 4
R1OUT
5
20 EN
R1OUT 5
T2IN
6
19 T4IN
T2IN 6
19 T4IN
T1IN
7
18 T3IN
T1IN 7
18 T3IN
GND
8
17 R3OUT
GND 8
17 R3OUT
VCC
9
16 R3IN
VCC 9
16 R3IN
15 V-
C1+ 10
15 V-
C1+ 10
14 C2-
V+ 11
14 C2-
C1- 12
13 C2+
C1- 12
13 C2+
+5V
9
0.1µF
T1IN
T2IN
T3IN
T4IN
20 T5OUT
V+ 11
+5V
0.1µF
21 T5IN
10
C1+
+
12
C113
C2+
+
14
C2-
VCC
11
+5V TO 10V
VOLTAGE DOUBLER
V+
+10V TO -10V
VOLTAGE INVERTER
V- 15
+
0.1µF
0.1µF
+
+5V
400kΩ
7
T1
+5V
400kΩ
T2
6
18
+5V
400kΩ
T3
+5V
400kΩ
19
T4
2
3
1
24
5
9
0.1µF
0.1µF
T1OUT
T1IN
T2OUT
T2IN
T3OUT
T3IN
T4OUT
T4IN
10
C1+
+
12
C113
C2+
+
14
C2-
R1IN
T5IN
5kΩ
R1
V+
+10V TO -10V
VOLTAGE INVERTER
V- 15
+5V
400kΩ
T2
6
18
+5V
400kΩ
T3
+5V
400kΩ
19
T4
+5V
400kΩ
T5
2
3
1
24
20
5
22
R2IN
20
5kΩ
R3
T4OUT
T5OUT
5kΩ
R2
21
SD
EN
T3OUT
R2IN
R3IN
R3OUT
T2OUT
23
R2OUT
16
T1OUT
R1IN
22
17
0.1µF
5kΩ
R1
5kΩ
R2
0.1µF
4
R1OUT
23
R2OUT
+
+
T1
21
11
+5V TO 10V
VOLTAGE DOUBLER
+5V
400kΩ
7
4
R1OUT
VCC
17
16
R3IN
R3OUT
GND
5kΩ
R3
8
GND
8
8-8
HIN200 thru HIN213
Pinouts
(Continued)
HIN208 (PDIP, SOIC, SSOP)
TOP VIEW
HIN209 (PDIP, SOIC, SSOP)
TOP VIEW
T2OUT 1
24 T3OUT
R1OUT 1
24 T1IN
T1OUT 2
23 R3IN
R1IN 2
23 T2IN
22 R3OUT
GND 3
22 R2OUT
R2IN 3
R2OUT 4
V+ 5
20 T2OUT
R1OUT 6
19 T3IN
C1+ 6
19 T1OUT
R1IN 7
18 T2IN
C1- 7
18 R3IN
GND 8
17 R4OUT
T1IN 5
20 T4OUT
VCC 9
16 R4IN
C1+ 10
R5IN 9
16 T3IN
15 V-
R5OUT 10
15 NC*
V+ 11
14 C2-
R4OUT 11
14 EN
C1- 12
13 C2+
R4IN 12
T1IN
T2IN
T3IN
T4IN
10
C1+
+
12
C113
C2+
+
14
C2-
VCC
11
+5V TO 10V
VOLTAGE DOUBLER
V+
+10V TO -10V
VOLTAGE INVERTER
V- 15
+5V
400kΩ
5
+5V
400kΩ
18
13 T3OUT
+9V TO +13.2V
+5V
9
0.1µF
17 R3OUT
V- 8
+5V
0.1µF
21 R2IN
VCC 4
21 T4IN
+
2
0.1µF
6
0.1µF
+
T1
4
0.1µF
T1IN
T1OUT
T2IN
+
7
VCC
C1+
C1-
+12V TO -12V
VOLTAGE INVERTER
V+
V-
5
8
+
+5V
400kΩ
24
T1
+5V
400kΩ
T2
23
16
+5V
400kΩ
T3
19
20
0.1µF
T1OUT
T2OUT
T2
1
T2OUT
T3IN
+5V
400kΩ
19
T3
+5V
400kΩ
21
T4
24
T3OUT
R1OUT
13
1
R1IN
5kΩ
R1
20
6
T4OUT
22
R1IN
R1OUT
R2IN
5kΩ
R2
5kΩ
R1
21
R2OUT
7
17
4
R3IN
R2IN
R2OUT
18
R3OUT
3
T3OUT
2
5kΩ
R3
5kΩ
R2
11
22
R3IN
R3OUT
R4IN
5kΩ
R4
5kΩ
R3
12
R4OUT
23
10
17
R4IN
R5IN
14
5kΩ
R4
9
R5OUT
16
R4OUT
5kΩ
R5
EN
GND
GND
8
3
8-9
HIN200 thru HIN213
Pinouts
(Continued)
HIN211 (SOIC, SSOP)
TOP VIEW
HIN213 (SOIC, SSOP)
TOP VIEW
T3OUT 1
28 T4OUT
T3OUT 1
28 T4OUT
T1OUT 2
27 R3IN
T1OUT 2
27 R3IN
26 R3OUT
T2OUT 3
26 R3OUT
T2OUT 3
R2IN 4
25 SD
R2IN 4
25 SD
R2OUT 5
24 EN
R2OUT 5
24 EN
T2IN 6
23 R4IN
T2IN 6
23 R4IN
T1IN 7
22 R4OUT
T1IN 7
22 R4OUT
R1OUT 8
21 T4IN
R1OUT 8
21 T4IN
R1IN 9
20 T3IN
R1IN 9
20 T3IN
GND 10
19 R5OUT
GND 10
19 R5OUT
VCC 11
18 R5IN
VCC 11
18 R5IN
C1+ 12
17 V-
C1+ 12
17 V-
V+ 13
16 C2-
V+ 13
16 C2-
C1- 14
15 C2+
C1- 14
15 C2+
NOTE: R4 AND R5 ACTIVE IN SHUTDOWN
+5V
+5V
11
11
0.1µF
0.1µF
T1IN
T2IN
T3IN
T4IN
R1OUT
12
C1+
+
14
C115
C2+
+
16
C2-
VCC
13
+5V TO 10V
VOLTAGE DOUBLER
V+
+10V TO -10V
VOLTAGE INVERTER
V- 17
+
+5V
400kΩ
T1
+5V
400kΩ
T2
6
20
+5V
400kΩ
T3
21
+5V
400kΩ
T4
2
3
1
28
9
8
0.1µF
0.1µF
+
7
0.1µF
0.1µF
T1OUT
T1IN
T2OUT
T2IN
T3OUT
T3IN
T4OUT
T4IN
R1OUT
R1IN
5
+5V
400kΩ
T2
6
20
+5V
400kΩ
T3
21
+5V
400kΩ
T4
28
T4OUT
9
R1IN
5kΩ
4
R2IN
5kΩ
27
R3IN
5kΩ
22
23
R4IN
5kΩ
R4
5kΩ
19
18
18
R5IN
R5OUT
R5IN
5kΩ
24
25
5kΩ
R5
25
EN
SD
EN
T3OUT
R4OUT
R4IN
R5
T2OUT
1
R3
23
19
T1OUT
3
8
5kΩ
R5OUT
0.1µF
R3OUT
R3IN
R4OUT
0.1µF
2
26
27
R4
+
R2
R3OUT
22
V- 17
T1
5kΩ
R3
+10V TO -10V
VOLTAGE INVERTER
+
R2OUT
R2IN
26
+5V TO 10V
VOLTAGE DOUBLER
5
4
13
V+
R1
R2OUT
R2
VCC
+5V
400kΩ
7
5kΩ
R1
24
12
C1+
+
14
C115
C2+
+
16
C2-
GND
GND
10
10
8-10
SD
HIN200 thru HIN213
Absolute Maximum Ratings
Thermal Information
VCC to Ground . . . . . . . . . . . . . . . . . . . . . . (GND -0.3V) <VCC < 6V
V+ to Ground . . . . . . . . . . . . . . . . . . . . . . . . (VCC -0.3V) <V+ < 12V
V- to Ground . . . . . . . . . . . . . . . . . . . . . . . -12V < V- < (GND +0.3V)
Input Voltages
TIN . . . . . . . . . . . . . . . . . . . . . . . . . (V- -0.3V) < VIN < (V+ +0.3V)
RIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30V
Output Voltages
TOUT . . . . . . . . . . . . . . . . . . . . (V- -0.3V) < VTXOUT < (V+ +0.3V)
ROUT. . . . . . . . . . . . . . . . . . (GND -0.3V) < VRXOUT < (V+ +0.3V)
Short Circuit Duration
TOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ROUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
16 Ld SOIC (N) Package . . . . . . . . . . . . . . . . . . . . .
115
16 Ld SOIC (W) Package . . . . . . . . . . . . . . . . . . . .
100
16 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . .
155
16 Ld PDIP Package . . . . . . . . . . . . . . . . . . . . . . . .
90
20 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
100
24 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
75
24 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . .
135
24 Ld PDIP (N) Package . . . . . . . . . . . . . . . . . . . . .
75
24 Ld PDIP (W) Package. . . . . . . . . . . . . . . . . . . . .
60
28 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
70
28 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . .
100
Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . . .-40oC to 85oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(SOIC and SSOP - Lead Tips Only)
Operating Conditions
Temperature Range
HIN-XXXCX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC
HIN-XXXIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
Test Conditions: VCC = +5V ±10%, (VCC = +5V ±5% HIN200, HIN203, HIN205, HIN207); V+ = 9V to
13.2V, HIN201 and HIN209), C1-C4 = 0.1µF; TA = Operating Temperature Range
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
±5
±9
±10
V
HIN202, HIN203
-
8
15
mA
HIN200, HIN204-208,
HIN211-213
-
11
20
mA
HIN201, HIN209
-
0.4
1
mA
HIN201
-
5.0
10
mA
HIN209
-
7.0
15
mA
HIN200, HIN205,
HIN206, HIN211
-
1
10
µA
HIN213
-
15
50
µA
-
-
0.8
V
Output Voltage Swing, TOUT
Transmitter Outputs, 3kΩ to Ground
Power Supply Current, ICC
No Load,
TA = 25oC
V+ Power Supply Current, ICC
Shutdown Supply Current, ICC(SD)
No Load,
TA = 25oC
TA = 25oC
Input Logic Low, TIN, EN, VlL
TIN , EN, SD, EN, SD
Input Logic High, VlH
TIN
2.0
-
-
V
EN, SD, EN, SD
2.4
-
-
V
-
15
200
µA
-30
-
+30
V
Logic Pullup Current, IP
TIN = 0V
RS-232 Input Voltage Range, VIN
Receiver Input Impedance, RIN
TA = 25oC, VIN = ±3V
3.0
5.0
7.0
kΩ
Receiver Input Low Threshold, VIN (H-L)
VCC = 5V,
TA = 25oC
Active Mode
0.8
1.2
-
V
Shutdown Mode
HIN213 R4 and R5
0.6
1.5
-
V
8-11
HIN200 thru HIN213
Test Conditions: VCC = +5V ±10%, (VCC = +5V ±5% HIN200, HIN203, HIN205, HIN207); V+ = 9V to
13.2V, HIN201 and HIN209), C1-C4 = 0.1µF; TA = Operating Temperature Range (Continued)
Electrical Specifications
PARAMETER
TEST CONDITIONS
Receiver Input High Threshold, VIN (L-H)
VCC = 5V,
TA = 25oC
MIN
TYP
MAX
UNITS
Active Mode
-
1.7
2.4
V
Shutdown Mode
HIN213 R4 and R5
-
1.5
2.4
V
Receiver Input Hysteresis, VHYST
VCC = 5V
No Hysteresis in Shutdown Mode
0.2
0.5
1.0
V
TTL/CMOS Receiver Output Voltage Low, VOL
IOUT = 1.6mA
(HIN201-HIN203, IOUT = 3.2mA)
-
0.1
0.4
V
TTL/CMOS Receiver Output Voltage High, VOH
IOUT = -1mA
3.5
4.6
-
V
Output Enable Time, tEN
HIN205, HIN206, HIN209, HIN211, HIN213
-
400
-
ns
Output Disable Time, tDIS
HIN205, HIN206, HIN209, HIN211, HIN213
-
200
-
ns
Transmit, Receive Propagation Delay, tPD
HIN213 SD = 0V, R4, R5
-
0.5
40
µs
HIN213 SD = VCC , R1 - R5
-
0.5
10
µs
HIN200 - HIN211
-
0.5
10
µs
RL = 3kΩ,
CL = 2500pF
Measured from
+3V to -3V or
-3V to +3V
(Note 1)
HIN200, HIN204 to
HIN211, HIN213
3
-
30
V/µs
HIN201, HIN202,
HIN203
3
-
30
V/µs
300
-
-
Ω
Transmit Transition Region Slew Rate, SRT
Output Resistance, ROUT
VCC = V+ = V- = 0V, VOUT = ±2V
RS-232 Output Short Circuit Current, ISC
TOUT Shorted to GND
-
±10
-
mA
TTL/CMOS Receiver Output Leakage
EN = VCC , EN = 0, 0V < ROUT < VCC
-
0.05
±10
µA
NOTE:
1. Guaranteed by design.
VOLTAGE DOUBLER
S1
VOLTAGE INVERTER
S2
C1+
V+ = 2VCC
S5
C2+
S6
VCC
GND
+
GND
S3
C1-
+
C1
-
+
C3
VCC
+
C2
-
GND
S4
S7
RC
OSCILLATOR
FIGURE 1. CHARGE PUMP
8-12
C2-
C4
V- = - (V+)
S8
HIN200 thru HIN213
Detailed Description
The HIN200 thru HIN213 family of RS-232 transmitters/receivers are powered by a single +5V power supply (except HIN201
and HIN209), feature low power consumption, and meet all ElA
RS232C and V.28 specifications. The circuit is divided into
three sections: the charge pump, transmitter, and receiver.
Charge Pump
0V to VCC . The output will be low whenever the input is
greater than 2.4V and high whenever the input is floating or
driven between +0.8V and -30V. The receivers feature 0.5V
hysteresis (except during shutdown) to improve noise rejection. The receiver Enable line (EN, on HIN206, HIN209, and
HIN211, EN on HIN213) when unasserted, disables the
receiver outputs, placing them in the high impedance mode.
The receiver outputs are also placed in the high impedance
state when in shutdown mode (except HIN213 R4 and R5).
An equivalent circuit of the charge pump is illustrated in
Figure 1. The charge pump contains two sections: the
voltage doubler and the voltage inverter. Each section is
driven by a two phase, internally generated clock to generate +10V and -10V. The nominal clock frequency is
125kHz. During phase one of the clock, capacitor C1 is
charged to VCC . During phase two, the voltage on C1 is
added to VCC , producing a signal across C3 equal to twice
VCC . During phase two, C2 is also charged to 2VCC , and
then during phase one, it is inverted with respect to ground
to produce a signal across C4 equal to -2VCC . The charge
pump accepts input voltages up to 5.5V. The output
impedance of the voltage doubler section (V+) is approximately 200Ω, and the output impedance of the voltage
inverter section (V-) is approximately 450Ω. A typical
application uses 0.1µF capacitors for C1-C4, however, the
value is not critical. Increasing the values of C1 and C2 will
lower the output impedance of the voltage doubler and
inverter, increasing the values of the reservoir capacitors,
C3 and C4, lowers the ripple on the V+ and V- supplies.
V+
VCC
400kΩ
TOUT
GND < TXIN < VCC
V- < VTOUT < V+
V-
FIGURE 2. TRANSMITTER
VCC
RXIN
-30V < RXIN < +30V
The receiver inputs accept up to ±30V while presenting the
required 3kΩ to 7kΩ input impedance even if the power is off
(VCC = 0V). The receivers have a typical input threshold of
1.3V which is within the ±3V limits, known as the transition
region, of the RS-232 specifications. The receiver output is
GND < VROUT < VCC
5kΩ
FIGURE 3. RECEIVER
Transmitters
Receivers
ROUT
GND
During shutdown mode (HIN200, HIN206 and HIN211,
SD = VCC , HIN213, SD = 0V) the charge pump is turned off,
V+ is pulled down to VCC , V- is pulled up to GND, and the
supply current is reduced to less than 10µA. The transmitter
outputs are disabled and the receiver outputs (except for
HIN213, R4 and R5) are placed in the high impedance state.
The transmitters are TTL/CMOS compatible inverters which
translate the inputs to RS-232 outputs. The input logic threshold is about 26% of VCC , or 1.3V for VCC = 5V. A logic 1 at the
input results in a voltage of between -5V and V- at the output,
and a logic 0 results in a voltage between +5V and (V+ -0.6V).
Each transmitter input has an internal 400kΩ pullup resistor
so any unused input can be left unconnected and its output
remains in its low state. The output voltage swing meets the
RS-232C specifications of ±5V minimum with the worst case
conditions of: all transmitters driving 3kΩ minimum load
impedance, VCC = 4.5V, and maximum allowable operating
temperature. The transmitters have an internally limited output
slew rate which is less than 30V/µs. The outputs are short circuit protected and can be shorted to ground indefinitely. The
powered down output impedance is a minimum of 300Ω with
±2V applied to the outputs and VCC = 0V.
300Ω
TXIN
TIN
OR
RIN
TOUT
OR
ROUT
VOL
VOL
tPHL
tPLH
AVERAGE PROPAGATION DELAY =
tPHL + tPLH
2
FIGURE 4. PROPAGATION DELAY DEFINITION
HIN213 Operation in Shutdown
The HIN213 features two receivers, R4 and R5, which
remain active in shutdown mode. During normal operation
the receivers propagation delay is typically 0.5µs. This propagation delay may increase slightly during shutdown. When
entering shut down mode, receivers R4 and R5 are not valid
for 80µs after SD = VIL. When exiting shutdown mode, all
receiver outputs will be invalid until the charge pump circuitry
reaches normal operating voltage. This is typically less than
2ms when using 0.1µF capacitors.
8-13
HIN200 thru HIN213
Typical Performance Curves
12
12
10
SUPPLY VOLTAGE (|V|)
V- SUPPLY VOLTAGE (V)
0.1µF
8
6
4
10
V+ (VCC = 5V)
8
6
V+ (VCC = 4V)
V- (VCC = 4V)
4
TA = 25oC
2
2
0
0
3.0
4.0
3.5
4.5
5.0
5.5
6.0
0
5
10
15
20
|ILOAD| (mA)
VCC
FIGURE 5.
V- SUPPLY VOLTAGE vs VCC
V- (VCC = 5V)
TRANSMITTER OUTPUTS
OPEN CIRCUIT
25
FIGURE 6. V+, V- OUTPUT VOLTAGE vs LOAD
Test Circuits (HIN202)
+4.5V TO
+5.5V INPUT
2 V+
+
1 C1+
0.1µF
C1
1 C1+
-
0.1µF
C3
+
2 V+
-
0.1µF +
C2 -
-
+
0.1µF C4
3kΩ
VCC 16
3kΩ
GND 15
3 C1-
T1OUT 14
4 C2+
R1IN 13
RS-232 ±30V INPUT
5 C2-
R1OUT 12
TTL/CMOS OUTPUT
6 V7 T2OUT
8 R2IN
T1 OUTPUT
T1IN 11
TTL/CMOS INPUT
T2IN 10
TTL/CMOS INPUT
R2OUT 9
30
VCC 16
GND 15
3 C1-
T1OUT 14
4 C2+
R1IN 13
5 C2-
R1OUT 12
6 V7 T2OUT
T1IN 11
T2IN 10
8 R2IN
R2OUT 9
ROUT = VIN /I
T2OUT
TTL/CMOS OUTPUT
T1OUT
T2
OUTPUT
VIN = ±2V
A
RS-232
±30V INPUT
FIGURE 7. GENERAL TEST CIRCUIT
FIGURE 8. POWER-OFF SOURCE RESISTANCE
CONFIGURATION
8-14
35
HIN200 thru HIN213
Application Information
+5V
TD
INPUTS
OUTPUTS
TTL/CMOS
RTS
5
TD
RTS
+
T1
11
14
T2
10
7
13
12
RD
CTS
9
R2
R1
8
15
RS-232
INPUTS AND OUTPUTS
TD (2) TRANSMIT DATA
RTS (4) REQUEST TO SEND
RD (3) RECEIVE DATA
CTS (5) CLEAR TO SEND
SIGNAL GROUND (7)
FIGURE 9. SIMPLE DUPLEX RS-232 PORT WITH CTS/RTS
HANDSHAKING
-
14
T2
10
+ C2
0.1µF
5
T1
11
TD (2) TRANSMIT DATA
7
RTS (4) REQUEST TO SEND
13
12
RD (3) RECEIVE DATA
RD
CTS
6
4
HIN202
3
9
HIN202
C2 +
0.1µF -
INPUTS
OUTPUTS
TTL/CMOS
CTR (20) DATA
TERMINAL READY
DSRS (24) DATA
SIGNALING RATE
SELECT
3
4
In applications requiring four RS-232 inputs and outputs
(Figure 10), note that each circuit requires two charge pump
capacitors (C1 and C2) but can share common reservoir
capacitors (C3 and C4). The benefit of sharing common reservoir capacitors is the elimination of two capacitors and the
reduction of the charge pump source impedance which
effectively increases the output swing of the transmitters.
1
16
1
C1 +
0.1µF -
A simple duplex RS-232 port with CTS/RTS handshaking is
illustrated in Figure 9. Fixed output signals such as DTR
(data terminal ready) and DSRS (data signaling rate select)
is generated by driving them through a 5kΩ resistor
connected to V+.
C1 +
0.1µF -
+
The HINXXX may be used for all RS-232 data terminal and
communication links. It is particularly useful in applications
where ±12V power supplies are not available for conventional RS-232 interface circuits. The applications presented
represent typical interface configurations.
R2
R1
8
CTS (5) CLEAR TO SEND
15
VCC
16
2
-
C3
+
+
C4
6
V- V+
0.2µF
6
-
0.2µF
2
VCC
16
+5V
RS-232
INPUTS AND OUTPUTS
HIN202
C1 +
0.1µF DTR
INPUTS
OUTPUTS
TTL/CMOS
DSRS
1
4
3
5
T1
11
14
T2
10
7
13
12
DCD
R1
9
R2
R1
15
8
+ C2
0.1µF
-
DTR (20) DATA TERMINAL READY
DSRS (24) DATA SIGNALING RATE SELECT
DCD (8) DATA CARRIER DETECT
R1 (22) RING INDICATOR
SIGNAL GROUND (7)
FIGURE 10. COMBINING TWO HIN202s FOR 4 PAIRS OF RS-232 INPUTS AND OUTPUTS
8-15
HIN200 thru HIN213
Die Characteristics
PASSIVATION:
DIE DIMENSIONS:
Type: Nitride over Silox
Nitride Thickness: 8kÅ
Silox Thickness: 7kÅ
160 mils x 140 mils
METALLIZATION:
Type: Al
Thickness: 10kÅ ±1kÅ
TRANSISTOR COUNT:
238
SUBSTRATE POTENTIAL
PROCESS:
V+
CMOS Metal Gate
Metallization Mask Layout
HIN211
SHD
EN
R4IN
R4OUT T4IN T3IN R5OUT
R5IN
R3OUT
V-
C2R3IN
T4OUT
C2+
T3OUT
C1T1OUT
V+
T2OUT
C1+
R2IN
VCC
R2OUT T2IN T1IN R1OUT
R1IN GND
8-16
Similar pages