MCP2003/4/3A/4A LIN J2602 Transceiver Features: Description: • The MCP2003/2003A and MCP2004/2004A are compliant with Local Interconnect Network (LIN) Bus Specifications 1.3, 2.0 and 2.1 and are compliant to SAE J2602 • Support Baud Rates up to 20 kbaudwith LIN-Compatible Output Driver • 43V Load Dump Protected • Very Low High Electromagnetic Immunity (EMI) meets Stringent Original Equipment Manufacturers (OEM) Requirements • Very High Electrostatic Discharge (ESD) Immunity: - >20 kV on VBB (IEC 61000-4-2) - >14 kV on LBUS (IEC 61000-4-2) • Very High Immunity to RF Disturbances meets Stringent OEM Requirements • Wide Supply Voltage, 6.0V-27.0V Continuous • Extended Temperature Range: -40 to +125°C • Interface to PIC® MCU EUSART and Standard USARTs • LIN Bus Pin: - Internal pull-up resistor and diode - Protected against battery shorts - Protected against loss of ground - High current drive • Automatic Thermal Shutdown • Low-Power mode: - Receiver monitoring bus and transmitter off, ( 5 µA) This device provides a bidirectional, half-duplex communication, physical interface to automotive and industrial LIN systems to meet the LIN Bus Specification Revision 2.1 and SAE J2602. The device is short-circuit and over-temperature protected by internal circuitry. The device has been specifically designed to operate in the automotive operating environment and will survive all specified transient conditions while meeting all of the stringent quiescent current requirements. MCP200X family members: • 8-pin PDIP, DFN and SOIC packages: - MCP2003, LIN-compatible driver, with WAKE pins, wake-up on falling edge of LBUS - MCP2003A, LIN-compatible driver, with WAKE pins, wake-up on rising edge of LBUS - MCP2004, LIN-compatible driver, with FAULT/TXE pins, wake-up on falling edge of LBUS - MCP2004A, LIN-compatible driver, with FAULT/TXE pins, wake-up on rising edge of LBUS Package Types MCP2003/2003A PDIP, SOIC MCP2004/2004A PDIP, SOIC RXD 1 8 VREN CS 2 7 VBB CS/WAKE 2 7 VBB 6 LBUS FAULT/TXE 3 6 LBUS WAKE 3 TXD 4 5 VSS MCP2003/2003A 4x4 DFN* RXD 1 8 VREN CS 2 7 VBB WAKE 3 TXD 4 EP 9 RXD 1 8 VREN TXD 4 5 VSS MCP2004/2004A 4x4 DFN* RXD 1 CS/WAKE 2 6 LBUS FAULT/TXE 3 TXD 4 5 VSS 8 VREN EP 9 7 VBB 6 LBUS 5 VSS * Includes Exposed Thermal Pad (EP); see Table 1-2. 2010-2014 Microchip Technology Inc. DS20002230F-page 1 MCP2003/4/3A/4A MCP2003/2003A Block Diagram VBB VREN Wake-Up Logic and Power Control 4.3V Ratiometric Reference WAKE RXD CS ~30 k TXD LBUS OC VSS Thermal Protection Short Circuit Protection MCP2004/2004A Block Diagram VBB VREN 4.3V 4.3V Wake-Up Logic and Power Control Ratiometric Reference RXD CS/WAKE TXD ~30 k OC LBUS FAULT/TXE VSS Thermal Protection DS20002230F-page 2 Short Circuit Protection 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A 1.0 DEVICE OVERVIEW 1.2.3 THERMAL PROTECTION The MCP2003/4/3A/4A devices provide a physical interface between a microcontroller and a LIN bus. These devices will translate the CMOS/TTL logic levels to LIN logic level, and vice versa. It is intended for automotive and industrial applications with serial bus speeds up to 20 kbaud. The thermal protection circuit monitors the die temperature and is able to shut down the LIN transmitter. LIN Bus Specification Revision 2.1 requires that the transceiver of all nodes in the system is connected via the LIN pin, referenced to ground and with a maximum external termination resistance load of 510 from LIN bus to battery supply. The 510 corresponds to 1 master and 15 slave nodes. • LIN bus output overload • Increase in die temperature due to increase in environment temperature The VREN pin can be used to drive the logic input of an external voltage regulator. This pin is high in all modes except for Power-Down mode. 1.1 1.1.1 There are two causes for a thermal overload. A thermal shutdown can be triggered by either, or both, of the following thermal overload conditions. Driving the TXD and checking the RXD pin makes it possible to determine whether there is a bus contention (Rx = low, Tx = high) or a thermal overload condition (Rx = high, Tx = low). After a thermal overload event, the device will automatically recover once the die temperature has fallen below the recovery temperature threshold (see Figure 1-1). External Protection REVERSE BATTERY PROTECTION FIGURE 1-1: THERMAL SHUTDOWN STATE DIAGRAM An external reverse-battery-blocking diode should be used to provide polarity protection (see Example 1-1). 1.1.2 TRANSIENT VOLTAGE PROTECTION (LOAD DUMP) An external 43V transient suppressor (TVS) diode, between VBB and ground, with a 50 transient protection resistor (RTP) in series with the battery supply and the VBB pin serve to protect the device from power transients (see Example 1-1) and ESD events. While this protection is optional, it is considered good engineering practice. 1.2 1.2.1 Shorted LIN bus to VBB Operation Transmitter Mode Shutdown Temp < ShutdownTEMP Internal Protection ESD PROTECTION For component-level ESD ratings, please refer to the maximum operation specifications. 1.2.2 GROUND LOSS PROTECTION The LIN Bus specification states that the LIN pin must transition to the recessive state when ground is disconnected. Therefore, a loss of ground effectively forces the LIN line to a high-impedance level. 2010-2014 Microchip Technology Inc. DS20002230F-page 3 MCP2003/4/3A/4A 1.3 Upon VBB supply pin power-on, the device will remain in Ready mode as long as CS is low. When CS transitions high, the device will either enter Operation mode, if TXD pin is held high, or the device will enter Transmitter Off mode, if TXD pin is held low. Modes of Operation For an overview of all operational modes, refer to Table 1-1. 1.3.1 POWER-DOWN MODE In Power-Down mode, everything is off except the wake-up section. This is the lowest power mode. The receiver is off, thus its output is open-drain. On CS going to a high level or a falling edge on WAKE (MCP2003/MCP2003A only), the device will enter Ready mode as soon as internal voltage stabilizes. Refer to Section 2.4 “AC Specifications” for further information. In addition, LIN bus activity will change the device from Power-down mode to Ready mode; MCP2003/4 wakes-up on a falling edge on LBUS, followed by a low level lasting at least 20 µs. MCP2003A/4A wakes-up on a rising edge on LBUS, followed by a high level lasting 70 µs typically. See Figures 1-2 to 1-5 about remote wake-up. If CS is held high as the device transitions from Power-Down to Ready mode, the device will transition to either Operation or Transmitter Off mode, depending on TXD input, as soon as internal voltages stabilize. 1.3.2 1.3.3 In this mode, all internal modules are operational. The device will go into Power-Down mode on the falling edge of CS. For the MCP2003/4 device, a specific process should be followed to put all nodes into PowerDown mode. Refer to Section 1.6 “MCP2003/4 and MCP2003A/4A Difference Details” and Figure 1-6. The device will enter Transmitter Off mode in the event of a Fault condition, such as: thermal overload, bus contention and TXD timer expiration. The MCP2004/2004A device can also enter Transmitter Off mode if the FAULT/TXE pin is pulled low. The VBB to LBUS pull-up resistor is connected only in Operation mode. 1.3.4 TRANSMITTER OFF MODE Transmitter Off mode is reached whenever the transmitter is disabled either due to a Fault condition or pulling the FAULT/TXE pin low on the MCP2004/2004A. The Fault conditions include: thermal overload, bus contention, RXD monitoring or TXD timer expiration. READY MODE Upon entering the Ready mode, VREN is enabled and the receiver detect circuit is powered up. The transmitter remains disabled and the device is ready to receive data but not to transmit. FIGURE 1-2: OPERATION MODE The device will go into Power-Down mode on the falling edge of CS, or return to Operation mode if all faults are resolved and the FAULT/TXE pin on the MCP2004/2004A is high. OPERATIONAL MODES STATE DIAGRAM – MCP2003 POR VREN OFF RX OFF TX OFF VBAT > 5.5V Ready VREN ON RX ON TX OFF CS = 1 & TXD = 1 CS = 1 & TXD = 0 Falling edge on LIN or CS = 1 or falling edge on WAKE pin TOFF Mode VREN ON RX ON TX OFF CS = 1 & TXD = 1 & No Fault Fault (thermal or timer) Operation Mode VREN ON RX ON TX ON CS = 0 CS = 0 POWER DOWN VREN OFF RX OFF TX OFF DS20002230F-page 4 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A FIGURE 1-3: OPERATIONAL MODES STATE DIAGRAM – MCP2003A POR VREN OFF RX OFF TX OFF VBAT > 5.5V Ready VREN ON RX OFF TX OFF CS = 1 & TXD = 1 CS = 1 & TXD = 0 TOFF Mode VREN ON RX ON TX OFF Rising edge on LIN or CS = 1 Or falling edge on WAKE pin CS = 1 & TXD = 1 & No Fault Fault (thermal or timer) Operation Mode VREN ON RX ON TX ON CS = 0 CS = 0 POWER DOWN VREN OFF RX OFF TX OFF FIGURE 1-4: OPERATIONAL MODES STATE DIAGRAM – MCP2004 POR VREN OFF RX OFF TX OFF VBAT > 5.5V Ready VREN ON RX ON TX OFF CS = 1 & TXD = 1 & TXE = 1 CS = 1 & (TXE = 0 or TXD = 0) Falling edge on LIN or CS = 1 TOFF Mode VREN ON RX ON TX OFF CS = 1 & TXD = 1 & TXE = 1 & No Fault Fault (thermal or timeout) or FAULT/TXE = 0 Operation Mode VREN ON RX ON TX ON CS = 0 CS = 0 POWER DOWN VREN OFF RX OFF TX OFF 2010-2014 Microchip Technology Inc. DS20002230F-page 5 MCP2003/4/3A/4A FIGURE 1-5: OPERATIONAL MODES STATE DIAGRAM – MCP2004A POR VREN OFF RX OFF TX OFF Ready VREN ON RX ON TX OFF VBAT > 5.5V CS = 1 & TXD = 1 & TXE = 1 CS = 1 & (TXE = 0 or TXD = 0) TOFF Mode VREN ON RX ON TX OFF Rising edge on LIN or CS = 1 CS = 1 & TXD = 1 & TXE = 1 & No Fault Fault (thermal or timeout) or FAULT/TXE = 0 Operation Mode VREN ON RX ON TX ON CS = 0 CS = 0 POWER DOWN VREN OFF RX OFF TX OFF TABLE 1-1: State OVERVIEW OF OPERATIONAL MODES Transmitter Receiver VREN Operation Comments POR OFF OFF OFF Check CS, if low then proceed to Ready VBB > VBB(MIN) mode; and Internal If high, transitions to either TOFF or Operation Supply stable mode, depending on TXD (2003/A), or TXD and FAULT/TXE (2004/A). Ready OFF ON ON If CS is high level, then proceed to Operation Bus Off state or TXOFF mode. Operation ON ON ON If CS is low level, then proceed to PowerDown; If FAULT/TXE low level, then proceed to Transmitter Off mode. Power-Down OFF Activity Detect OFF On CS high level, proceed to Ready mode Low-Power mode then proceed to either Operation mode or TXOFF. MCP2003/2003A: Falling edge on WAKE will put the device into Ready mode. MCP2003/MCP2004: falling edge on LIN bus will put the device into Ready mode. MCP2003A/MCP2004A: rising edge on LIN bus will put the device into Ready mode. Transmitter Off OFF ON ON If CS is low level, then proceed to PowerDown mode; If FAULT/TXE and TXD high, then proceed to Operation mode DS20002230F-page 6 Normal Operation mode FAULT/TXE only available on MCP2004/2004A 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A 1.4 Typical Applications EXAMPLE 1-1: TYPICAL MCP2003/2003A APPLICATION +12 optional resistor and transient suppressor +12 50 43V 1.0 µF (1) Master Node Only +12 3.9 k VDD Voltage Reg 4.7 k VREN TXD TXD RXD RXD I/O 33 k VBB 1 k LIN Bus LBUS CS (2) MMBZ27V WAKE 220pF Wake-up VSS Note 1: For applications with current requirements of less than 20 mA, the connection to +12V can be deleted, and voltage to the regulator supplied directly from the VREN pin. 2: ESD protection diode. EXAMPLE 1-2: TYPICAL MCP2004/2004A APPLICATION +12 +12 optional resistor and transient suppressor Wake-up 50 43V (1) 1.0 µF Master Node Only +12 220 k VDD 4.7 k Voltage Reg VREN TXD TXD RXD RXD I/O CS/WAKE I/O FAULT/TXE VBB 1 k LIN Bus LBUS (2) MMBZ27V 220pF 100 nF VSS Note 1: For applications with current requirements of less than 20 mA, the connection to +12V can be deleted, and voltage to the regulator supplied directly from the VREN pin. 2: ESD protection diode. 2010-2014 Microchip Technology Inc. DS20002230F-page 7 MCP2003/4/3A/4A EXAMPLE 1-3: TYPICAL LIN NETWORK CONFIGURATION 40m + Return LIN bus VBB 1 k LIN bus MCP200X LIN bus MCP200X Slave 1 (MCU) LIN bus MCP200X LIN bus MCP200X Slave 2 (MCU) Slave n <23 (MCU) Master (MCU) DS20002230F-page 8 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A 1.5 Pin Descriptions TABLE 1-2: PINOUT DESCRIPTIONS 8-Lead PDIP, SOIC 4x4 DFN RXD 1 1 Receive Data Output (OD), HV tolerant Receive Data Output (OD), HV tolerant CS 2 2 Chip Select (TTL), HV tolerant Chip Select/Local WAKE (TTL), HV tolerant WAKE (MCP2003/2003A only) 3 3 Wake-up, HV tolerant Fault Detect Output (OD) Transmitter Enable (TTL) HV tolerant TXD 4 4 Transmit Data Input (TTL), HV tolerant Transmit Data Input (TTL), HV tolerant VSS 5 5 Ground Ground LBUS 6 6 LIN Bus (bidirectional) LIN Bus (bidirectional) VBB 7 7 Battery Positive Battery Positive VREN 8 8 Voltage Regulator Enable Output Voltage Regulator Enable Output EP — 9 Exposed Thermal Pad. Do not electrically connect or connect to Vss Pin Name MCP2003/2003A MCP2004/2004A Normal Operation Normal Operation FAULT/TXE (MCP2004/2004A only) Exposed Thermal Pad. Do not electrically connect or connect to Vss Legend: TTL = TTL Input Buffer; OD = Open-Drain Output 1.5.1 RECEIVE DATA OUTPUT (RXD) The Receive Data Output pin is an open drain (OD) output and follows the state of the LIN pin, except in Power Down mode. 1.5.1.1 RXD Monitoring The RXD pin is internally monitored. It has to be at a high level (> 2.5V typical) while LBUS is recessive. Otherwise, an internal fault will be created and the device will transition to Transmitter Off mode. On the MCP2004/2004A, the FAULT/TXE pin will be driven low to indicate the Transmitter Off state. 1.5.2 CHIP SELECT (CS) This is the Chip Select Input pin. An internal pull-down resistor will keep the CS pin low. This is done to ensure that no disruptive data will be present on the bus while the microcontroller is executing a Power-on Reset and an I/O initialization sequence. The pin must detect a high level to activate the transmitter. An internal LowPass filter, with a typical time constant of 10 µs, prevents unwanted wake-up (or transition to Power Down mode) on glitches. If CS = 0 when the VBB supply is turned on, the device goes to Ready mode as soon as internal voltages stabilize, and stays there as long as the CS pin is held low (0). In Ready mode, the receiver is on, and the LIN transmitter driver is off. 2010-2014 Microchip Technology Inc. If CS = 1 when the VBB supply is turned on, the device will proceed to Operation mode, or TXOFF (refer to Figures 1-2 to 1-5), as soon as internal voltages stabilize. This pin may also be used as a local wake-up input (refer to Example 1-1). In this implementation, the microcontroller I/O controlling the CS should be converted to a high-impedance input allowing the internal pull-down resistor to keep CS low. An external switch, or other source, can then wake-up both the transceiver and the microcontroller (if powered). Refer to Section 1.3 “Modes of Operation”, for detailed operation of CS. Note: 1.5.3 It is not recommended to tie CS high as this can result in the device entering Operation mode before the microcontroller is initialized and may result in unintentional LIN traffic. WAKE-UP INPUT (WAKE) This pin is only available on the MCP2003/2003A. The WAKE pin has an internal 800 kΩ pull-up to VBB. A falling edge on the WAKE pin causes the device to wake from Power-Down mode. Upon waking, the MCP2003/3A will enter Ready mode. DS20002230F-page 9 MCP2003/4/3A/4A 1.5.4 FAULT/TXE drive. While the transmitter is disabled, the internal 30 k pull-up resistor on the LBUS pin is also disconnected to reduce current. This pin is only available on the MCP2004/2004A. This pin is bidirectional and allows disabling of the transmitter, as well as fault reporting related to disabling the transmitter. This pin is an open-drain output, with states as defined in Table 1-3. The transmitter is disabled whenever this pin is low (‘0’), either from an internal Fault condition or by an external TABLE 1-3: Note: The FAULT/TXE pin is true (‘0’) whenever the internal circuits have detected a short or thermal excursion and have disabled the LBUS output driver. FAULT/TXE TRUTH TABLE FAULT/TXE TXD In RXD Out LINBUS I/O Thermal Override L H VBB OFF H H VBB OFF L L GND OFF H L GND OFF Definition External Input Driven Output H L FAULT, TXD driven low, LBUS shorted to VBB (Note 1) H H OK H H OK H H OK, data is being received from LBUS x x VBB ON H L FAULT, Transceiver in thermal shutdown x x VBB x L x NO FAULT, the CPU is commanding the transceiver to turn off the transmitter driver Legend: x = don’t care. Note 1: The FAULT/TXE is valid after approximately 25 µs after TXD falling edge. This is to eliminate false fault reporting during bus propagation delays. 1.5.5 TRANSMIT DATA INPUT (TXD) The Transmit Data Input pin has an internal pull-up. The LIN pin is low (dominant) when TXD is low, and high (recessive) when TXD is high. For extra bus security, TXD is internally forced to ‘1’ whenever the transmitter is disabled regardless of external TXD voltage. 1.5.5.1 TXD Dominant Timeout If TXD is driven low for longer than approximately 25 ms, the LBUS pin is switched to Recessive mode and the part enters TOFF Mode. This is to prevent the LIN node from permanently driving the LIN Bus dominant. The transmitter is reenabled on TXD rising edge. 1.5.6 GROUND (VSS) 1.5.7.1 The Bus Dominant Timer is an internal timer that deactivates the LBUS transmitter after approximately 25 ms of dominant state on the LBUS pin. The timer is reset on any recessive LBUS state. The LIN bus transmitter will be reenabled after a recessive state on the LBUS pin as long as CS is high. Disabling can be caused by the LIN bus being externally held dominant, or by TXD being driven low. Additionally, on the MCP2004/2004A, the FAULT pin will be driven low to indicate the Transmitter Off state. 1.5.8 LIN BUS (LBUS) The bidirectional LIN Bus pin (LBUS) is controlled by the TXD input. LBUS has a current limited open collector output. To reduce EMI, the edges during the signal changes are slope controlled and include corner rounding control for both falling and rising edges. BATTERY (VBB) This is the Battery Positive Supply Voltage pin. 1.5.9 This is the Ground pin. 1.5.7 Bus Dominant Timer VOLTAGE REGULATOR ENABLE OUTPUT (VREN) This is the External Voltage Regulator Enable pin. Open source output is pulled high to VBB in all modes, except Power-Down. 1.5.10 EXPOSED THERMAL PAD (EP) Do not electrically connect, or connect to Vss. The internal LIN receiver observes the activities on the LIN bus, and matches the output signal RXD to follow the state of the LBUS pin. DS20002230F-page 10 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A 1.6 MCP2003/4 and MCP2003A/4A Difference Details The differences between the MCP2003/4 and the MCP2003/4A devices are isolated to the wake-up functionality. The changes were implemented to make the device more robust to LIN bus conditions, outside of the normal operating conditions. The MCP2003/4 will wake-up from Power-Down mode during any LIN falling edge held low longer than 20 µs. In the case where a LIN system is designed to minimize stand-by current by disconnecting all bus pull-ups resistors (including the external master pull-up resistor to VBB), the original MCP2003/4 could wake-up, if the floating bus drifted to a valid low level. The MCP2003/4A revisions were modified to require a rising edge after a valid low level. This will prevent an undesired system wake-up in this scenario, while maintaining functional capability with the original version. It should be noted that the original MCP2003/4 meets all LIN transceiver specification requirements and modules can be designed to pass all LIN system requirements. However, when all bus pull-up resistors are disconnected, the MCP2003/4 requires the module designer to write firmware to monitor the LIN Bus after any wake-up event to prevent the transceiver from automatically transitioning from Ready mode to Operational mode. If the MCP2003/4 is placed into Operational mode, VBB to LBUS pull-up resistor is automatically connected, which will raise the LIN bus to a recessive level; then putting the device to Power-Down mode may cause LBUS to be floating, and thus wake-up all bus nodes. To prevent this, the designer should ensure TXD (MCP2003) or TXE (MCP2004) is held low until valid bus activity is verified (see Figure 1-6). This will ensure the transceiver transitions from Ready mode to Transmitter Off mode, until bus activity can be verified. In the case of valid bus activity, the transceiver can shift to Operation mode, while if there is no bus activity, the device can be again placed into Power Down. The design practices needed to accomplish this are fully detailed in Tech Brief TB3067 – “MCP2003 PowerDown Mode and Wake-Up Handling in Case of LIN Bus Loss” (DS93067). The revised MCP2003/4A devices now eliminate the need for firmware to prevent system wide wake-up. The revised devices now require a longer valid bus low (see updated tBDB value in Section 2.3 “DC Specifications” and Figure 2-7), which enables a rising edge detect circuit. The device will now only wake-up after a rising edge, following a low longer than tBDB. While the module designer can still hold TXD (MCP2003) or TXE (MCP2004) low during wake-up, to enter Transmitter Off mode from Ready mode, it is not required to prevent an advertent system wake-up. In addition to the longer tBDB value, the time from wakeup detect to VREN enable is shortened as documented in Section 2.3 “DC Specifications”. FIGURE 1-6: MCP2003/2004 SWITCHING TIMING DIAGRAM FOR THE FORCED POWERDOWN MODE SEQUENCE tTx2CS 100nstCSactive 100µs CS VREN TXD state depending on how the Slave Microcontroller is powered TXD to forced externally TXD LIN bus disconnected LBUS State Power Down Mode after Master Sleep instruction 2010-2014 Microchip Technology Inc. Ready Mode Transmitter OFF Mode Power Down Mode DS20002230F-page 11 MCP2003/4/3A/4A 2.0 ELECTRICAL CHARACTERISTICS 2.1 Absolute Maximum Ratings† VIN DC Voltage on RXD, TXD, FAULT/TXE, CS .............................................................................................. -0.3 to +43V VIN DC Voltage on WAKE and VREN ............................................................................................................. -0.3 to +VBB VBB Battery Voltage, continuous, non-operating (Note 1)............................................................................. -0.3 to +40V VBB Battery Voltage, non-operating (LIN bus recessive) (Note 2) ................................................................ -0.3 to +43V VBB Battery Voltage, transient ISO 7637 Test 1 ..................................................................................................... -200V VBB Battery Voltage, transient ISO 7637 Test 2a ...................................................................................................+150V VBB Battery Voltage, transient ISO 7637 Test 3a ................................................................................................... -300V VBB Battery Voltage, transient ISO 7637 Test 3b ...................................................................................................+200V VLBUS Bus Voltage, continuous ...................................................................................................................... -18 to +40V VLBUS Bus Voltage, transient (Note 3) ........................................................................................................... -27 to +43V ILBUS Bus Short Circuit Current Limit ....................................................................................................................200 mA ESD protection on LIN, VBB, WAKE (IEC 61000-4-2) (Note 4)............................................................................... ±8 KV ESD protection on LIN, VBB (Human Body Model) (Note 5) ................................................................................... ±8 KV ESD protection on all other pins (Human Body Model) (Note 5) ............................................................................ ±4 KV ESD protection on all pins (Charge Device Model) (Note 6)................................................................................... ±2 KV ESD protection on all pins (Machine Model) (Note 7).............................................................................................±200V Maximum Junction Temperature ............................................................................................................................. 150C Storage Temperature...................................................................................................................................-65 to +150C † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device, at those or any other conditions above those indicated in the operational listings of this specification, is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Note 1: LIN 2.x compliant specification. 2: SAE J2602 compliant specification. 3: ISO 7637/1 load dump compliant (t < 500 ms). 4: According to IEC 61000-4-2, 330 ohm, 150 pF and Transceiver EMC Test Specifications [2] to [4]. For WAKE pin to meet the specification, series resistor must be in place (refer to Example 1-2). 5: According to AEC-Q100-002/JESD22-A114. 6: According to AEC-Q100-011B. 7: According to AEC-Q100-003/JESD22-A115. 2.2 Nomenclature Used in This Document Some terms and names used in this data sheet deviate from those referred to in the LIN specifications. Equivalent values are shown below. LIN 2.1 Name Term used in the following tables Definition VBAT not used VSUP VBB Supply voltage at device pin Current Limit of driver ECU operating voltage IBUS_LIM ISC VBUSREC VIH(LBUS) Recessive state VBUSDOM VIL(LBUS) Dominant state DS20002230F-page 12 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A 2.3 DC Specifications DC Specifications Parameter Electrical Characteristics: Unless otherwise indicated, all limits are specified for VBB = 6.0V to 30.0V, TA = -40°C to +125°C Sym. Min. Typ. Max. Units Conditions VBB Quiescent Operating Current IBBQ — 90 150 µA Operating Mode, bus recessive (Note 1) VBB Transmitter-off Current IBBTO — 75 120 µA Transmitter off, bus recessive (Note 1) Power VBB Power-Down Current IBBPD — 5 15 µA IBBNOGND -1 — 1 mA High-Level Input Voltage (TXD, FAULT/TXE) VIH 2.0 — 30 V Low-Level Input Voltage (TXD, FAULT/TXE) VIL -0.3 — 0.8 V High-Level Input Current (TXD, FAULT/TXE) IIH -2.5 — — µA Input voltage = 4.0V Low-Level Input Current (TXD, FAULT/TXE) IIL -10 — — µA Input voltage = 0.5V High-Level Voltage (VREN) VHVREN -0.3 — VBB+0.3 V High-Level Output Current (VREN) IHVREN -40 — -10 mA -125 — -35 Current with VSS Floating VBB VBB = 12V, GND to VBB, VLIN = 0-27V Microcontroller Interface Output voltage = VBB0.5V Output voltage = VBB2.0V High-Level Input Voltage (CS) VIH 2.0 — 30 V Low-Level Input Voltage (CS) VIL -0.3 — 0.8 V High-Level Input Current (CS) IIH — — 10.0 µA Input voltage = 4.0V Low-Level Input Current (CS) IIL — — 5.0 µA Input voltage = 0.5V Low-Level Input Voltage (WAKE) VIL VBB – 4.0V — — V Low-Level Output Voltage (RXD) VOL — — 0.4 V IIN = 2 mA High-Level Output Current (RXD) IOH -1 — -1 µA VLIN = VBB, VRXD = 5.5V Note 1: 2: Through a current limiting resistor Internal current limited. 2.0 ms maximum recovery time (RLBUS = 0, TX = 0.4 VREG, VLBUS = VBB). Node has to sustain the current that can flow under this condition; bus must be operational under this condition. 2010-2014 Microchip Technology Inc. DS20002230F-page 13 MCP2003/4/3A/4A 2.3 DC Specifications (Continued) DC Specifications Parameter Electrical Characteristics: Unless otherwise indicated, all limits are specified for VBB = 6.0V to 30.0V, TA = -40°C to +125°C Sym. Min. Typ. Max. Units Conditions High-Level Input Voltage VIH(LBUS) 0.6 VBB — — V Recessive state Low-Level Input Voltage VIL(LBUS) -8 — 0.4 VBB V Dominant state VHYS — — 0.175 VBB V VIH(LBUS) – VIL(LBUS) Low-Level Output Current IOL(LBUS) 40 — 200 mA High-Level Output Current IOH(LBUS) — — 20 µA Pull-up Current on Input IPU(LBUS) 5 — 180 µA ~30 k internal pull-up @ VIH (LBUS) = 0.7 VBB Short Circuit Current Limit ISC 50 — 200 mA (Note 1) High-Level Output Voltage Bus Interface Input Hysteresis Output voltage = 0.1 VBB, VBB = 12V VOH(LBUS) 0.9 VBB — VBB V Driver Dominant Voltage V_LOSUP — — 1.2 V VBB = 7V, RLOAD = 500 Driver Dominant Voltage V_HISUP — — 2.0 V VBB = 18V, RLOAD = 500 Driver Dominant Voltage V_LOSUP - 1K 0.6 — — V VBB = 7V, RLOAD = 1 k Driver Dominant Voltage V_HISUP - 1K 0.8 — — V Input Leakage Current (at the receiver during dominant bus level) IBUS_PAS_DOM -1 -0.4 — mA Driver off, VBUS = 0V, VBB = 12V Input Leakage Current (at the receiver during recessive bus level) IBUS_PAS_REC — 12 20 µA Driver off, 8V < VBB < 18V 8V < VBUs < 18V VBUS VBB Leakage Current (disconnected from ground) IBUS_NO_GND -10 1.0 +10 µA GNDDEVICE = VBB, 0V < VBUS < 18V, VBB = 12V Leakage Current (disconnected from VBB) IBUS_NO_VBB — — 10 µA VBB = GND, 0 < VBUS < 18V, (Note 2) Receiver Center Voltage VBUS_CNT 0.525 VBB V VBUS_CNT = (VIL (LBUS) + VIH (LBUS))/2 0.475 VBB 0.5 VBB Slave Termination RSLAVE 20 30 47 k Capacitance of Slave Node CSLAVE — — 50 pF Note 1: 2: VBB = 18V, RLOAD = 1 k Internal current limited. 2.0 ms maximum recovery time (RLBUS = 0, TX = 0.4 VREG, VLBUS = VBB). Node has to sustain the current that can flow under this condition; bus must be operational under this condition. DS20002230F-page 14 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A 2.4 AC Specifications AC Characteristics Electrical Characteristics: Unless otherwise indicated, all limits are specified for VBB = 6.0V to 27.0V; TA = -40°C to +125°C Parameter Sym. Min. Typ. Max. Units Test Conditions Bus Interface – Constant Slope Time Parameters Slope Rising and Falling Edges Propagation Delay of Transmitter tSLOPE 3.5 — 22.5 µs 7.3V <= VBB <= 18V tTRANSPD — — 4.0 µs tTRANSPD = max (tTRANSPDR or tTRANSPDF) Propagation Delay of Receiver tRECPD — — 6.0 µs tRECPD = max (tRECPDR or tRECPDF) Symmetry of Propagation Delay of Receiver Rising Edge w.r.t. Falling Edge tRECSYM -2.0 — 2.0 µs tRECSYM = max (tRECPDF – tRECPDR) RRXD 2.4 to VCC, CRXD 20 pF tTRANSSYM -2.0 — 2.0 µs tTRANSSYM = max (tTRANSPDF tTRANSPDR) tFAULT — — 32.5 µs tFAULT = max (tTRANSPD + tSLOPE + tRECPD) Duty Cycle 1 @20.0 kbit/sec 0.396 — — — CBUS; RBUS conditions: 1 nF; 1 k | 6.8 nF; 660 | 10 nF; 500 THREC(MAX) = 0.744 x VBB, THDOM(MAX) = 0.581 x VBB, VBB =7.0V – 18V; tBIT = 50 µs D1 = tBUS_REC(MIN)/2 x tBIT) Duty Cycle 2 @20.0 kbit/sec — — 0.581 — CBUS; RBUS conditions: 1 nF; 1 k | 6.8 nF; 660 | 10 nF; 500 THREC(MAX) = 0.284 x VBB, THDOM(MAX) = 0.422 x VBB, VBB =7.6V – 18V; tBIT = 50 µs D2 = tBUS_REC(MAX)/2 x tBIT) Duty Cycle 3 @10.4 kbit/sec 0.417 — — — CBUS; RBUS conditions: 1 nF; 1 k | 6.8 nF; 660 | 10 nF; 500 THREC(MAX) = 0.778 x VBB, THDOM(MAX) = 0.616 x VBB, VBB =7.0V – 18V; tBIT = 96 µs D3 = tBUS_REC(MIN)/2 x tBIT) Duty Cycle 4 @10.4 kbit/sec — — 0.590 — CBUS; RBUS conditions: 1 nF; 1 k | 6.8 nF; 660 | 10 nF; 500 THREC(max) = 0.251 x VBB, THDOM(MAX) = 0.389 x VBB, VBB =7.6V – 18V; tBIT = 96 µs D4 = tBUS_REC(MAX)/2 x tBIT) 5 — 20 µs MCP2003/2004 30 70 125 µs MCP2003A/2004A 35 — 150 µs MCP2003/2004 MCP2003A/2004A Symmetry of Propagation Delay of Transmitter Rising Edge w.r.t. Falling Edge Time to Sample of FAULT/TXE for Bus Conflict Reporting Wake-up Timing Bus Activity Debounce time Bus Activity to VREN on tBDB tBACTVE 10 30 90 µs WAKE to VREN on tWAKE — — 150 µs Chip Select to VREN on tCSOR — — 150 µs VREN floating Chip Select to VREN off tCSPD — — 80 µs VREN floating 2010-2014 Microchip Technology Inc. DS20002230F-page 15 MCP2003/4/3A/4A 2.5 Thermal Specifications Parameter Symbol Typ. Max. Units Recovery Temperature RECOVERY +140 — C Shutdown Temperature SHUTDOWN +150 — C tTHERM 1.5 5.0 ms Thermal Resistance, 8L-DFN JA 35.7 — C/W Thermal Resistance, 8L-PDIP JA 89.3 — C/W Thermal Resistance, 8L-SOIC JA 149.5 — C/W Short Circuit Recovery Time Test Conditions Thermal Package Resistances Note 1: The maximum power dissipation is a function of TJMAX, JA and ambient temperature TA. The maximum allowable power dissipation at an ambient temperature is PD = (TJMAX - TA)JA. If this dissipation is exceeded, the die temperature will rise above 150C and the device will go into thermal shutdown. DS20002230F-page 16 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A 2.6 Typical Performance Curves The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Note: Unless otherwise indicated, VBB = 6.0V to 18.0V, TA = -40°C to +125°C. FIGURE 2-1: TYPICAL IBBQ FIGURE 2-3: 0.14 0.12 0.12 0.1 0.1 -40C 25C 85C 125C 0.08 0.06 0.04 Current (mA) Current (mA) TYPICAL IBBTO 0.08 -40C 25C 85C 125C 0.06 0.04 0.02 0.02 0 0 6 7.3 12 14.4 18 6V VBB (V) FIGURE 2-2: 7.3V 12V 14.4V 18V VBB (V) TYPICAL IBBPD 0.008 0.007 Current (mA) 0.006 0.005 -40C 25C 0.004 85C 125C 0.003 0.002 0.001 0 6 7.3 12 14.4 18 VBB (V) 2010-2014 Microchip Technology Inc. DS20002230F-page 17 MCP2003/4/3A/4A 2.7 Timing Diagrams and Specifications FIGURE 2-4: BUS TIMING DIAGRAM TXD 50% 50% LBUS .95VLBUS .50VBB 0.05VLBUS TTRANSPDR TTRANSPDF TRECPDF 0.0V TRECPDR RXD 50% Internal TXD/RXD Compare Match 50% Match Match Match Match FAULT Sampling TFAULT TFAULT FAULT/TXE Output FIGURE 2-5: CS Stable Hold Value Stable Hold Value Stable CS TO VREN TIMING DIAGRAM TCSOR VBB VREN OFF TCSPD DS20002230F-page 18 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A FIGURE 2-6: MCP2003/4 REMOTE WAKE-UP LBUS 0.4VBB tBDB tBACTIVE VBB VREN FIGURE 2-7: MCP2003A/4A REMOTE WAKE-UP LBUS 0.4VBB tBDB tBACTIVE VBB VREN 2010-2014 Microchip Technology Inc. DS20002230F-page 19 MCP2003/4/3A/4A 3.0 PACKAGING INFORMATION 3.1 Package Marking Information Examples: 8-Lead DFN (4x4) 2004A e3 E/MD^^ 1406 256 8-Lead PDIP (300 mil) Examples: MCP2003A e3 E/P^^256 1406 8-Lead SOIC (150 mil) Examples: MCP2003E SN^^1406 e3 256 Legend: XX...X Y YY WW NNN e3 * Note: DS20002230F-page 20 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC® designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A 8-Lead Plastic Dual Flat, No Lead Package (MD) – 4x4x0.9 mm Body [DFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Microchip Technology Drawing C04-131E Sheet 1 of 2 2010-2014 Microchip Technology Inc. DS20002230F-page 21 MCP2003/4/3A/4A 8-Lead Plastic Dual Flat, No Lead Package (MD) – 4x4x0.9 mm Body [DFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Microchip Technology Drawing C04-131E Sheet 2 of 2 DS20002230F-page 22 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2010-2014 Microchip Technology Inc. DS20002230F-page 23 MCP2003/4/3A/4A 3 & ' !&" & 4# *!( !!& 4 %& &#& && 255***' '5 4 N NOTE 1 E1 1 3 2 D E A2 A L A1 c e eB b1 b 6&! '! 9'&! 7"') %! 7,8. 7 7 & ; < & & 7: 1, = = - 1!& & = = . - - ##4 "# & 4!! "# >#& ##4>#& . < : 9& -< -? 9 - < ) ? ) < 1 = = & & 9# 6 4!! 9#>#& 9 * 9#>#& : * + - !"#$%&" ' ()"&'"!&) &#*& & & # +%&, & !& - '! !#.# &"#' #%! & "! ! #%! & "! !! &$#/ !# '! #& .0 1,21!'! &$& "! **& "&& ! DS20002230F-page 24 * ,<1 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2010-2014 Microchip Technology Inc. DS20002230F-page 25 MCP2003/4/3A/4A Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20002230F-page 26 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A ! ""#$%& !' 3 & ' !&" & 4# *!( !!& 4 %& &#& && 255***' '5 4 2010-2014 Microchip Technology Inc. DS20002230F-page 27 MCP2003/4/3A/4A NOTES: DS20002230F-page 28 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A APPENDIX A: REVISION HISTORY Revision F (November 2014) The following is the list of modifications: 1. Updated typical application circuits with values used during ESD tests. Revision E (October 2013) The following is the list of modifications: 2. 3. 4. Added additional specification for IHVREN in Section 2.3 “DC Specifications”. Clarified wake-up on LBUS functionality. Added RXD monitoring description. Revision D (December 2011) The following is the list of modifications: 5. 6. Added the MCP2003A and MCP2004A devices and related information throughout the document. Updated Figures 1.2, 1.3, 1.4, 1.5, 2.6, 2.7. Revision C (August 2010) The following is the list of modifications: 1. Updated all references of Sleep mode to PowerDown mode, and updated the Max. parameter for Duty Cycle 2 in Section 2.4 “AC Specifications”. Revision B (July 2010) The following is the list of modifications: 1. Added Section 2.2 “Nomenclature Used in This Document”, and added the “Capacitance of Slave Node” parameter to Section 2.3 “DC Specifications”. Revision A (March 2010) • Original Release of this Document. 2010-2014 Microchip Technology Inc. DS20002230F-page 29 MCP2003/4/3A/4A NOTES: DS20002230F-page 30 2010-2014 Microchip Technology Inc. MCP2003/4/3A/4A PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX Device Temperature Range Package Examples: a) b) Device: MCP2003: LIN Transceiver, with WAKE pins, wake-up on falling edge of LBUS MCP2003T: LIN Transceiver, with WAKE pins, wake-up on falling edge of LBUS (Tape and Reel) (DFN and SOIC only) MCP2003A: LIN Transceiver, with WAKE pins, wake-up on rising edge of LBUS MCP2003AT: LIN Transceiver, with WAKE pins, wake-up on rising edge of LBUS (Tape and Reel) (DFN and SOIC only) LIN Transceiver with FAULT/TXE pins, wake-up on falling edge of LBUS MCP2004T: LIN Transceiver with FAULT/TXE pins, wake-up on falling edge of LBUS (Tape and Reel) (DFN and SOIC only) MCP2004A: LIN Transceiver with FAULT/TXE pins, wake-up on rising edge of LBUS MCP2004AT: LIN Transceiver with FAULT/TXE pins, wake-up on rising edge of LBUS (Tape and Reel) (DFN and SOIC only) MCP2004: Temperature Range: E Package: = -40°C to +125°C c) d) e) a) b) c) d) e) MCP2003A-E/MD: Extended Temperature, 8L-DFN package MCP2003A-E/P: Extended Temperature, 8L-PDIP package MCP2003A-E/SN: Extended Temperature, 8L-SOIC package MCP2003AT-E/MD: Tape and Reel, Extended Temperature, 8L-DFN package MCP2003AT-E/SN: Tape and Reel, Extended Temperature, 8L-SOIC package MCP2004-E/MD: Extended Temperature, 8L-DFN package MCP2004-E/P: Extended Temperature, 8L-PDIP package MCP2004A-E/SN: Extended Temperature, 8L-SOIC package MCP2004AT-E/MD: Tape and Reel, Extended Temperature, 8L-DFN package MCP2004AT-E/SN: Tape and Reel, Extended Temperature, 8L-SOIC package MD = Plastic Dual Flat, No Lead Package - 4x4x0.9mm Body, 8-lead P = Plastic Dual In-Line - 300 mil Body, 8-lead SN = Plastic Small Outline - Narrow 3.90mm Body, 8-lead 2010-2014 Microchip Technology Inc. DS20002230F-page 31 MCP2003/4/3A/4A NOTES: DS20002230F-page 32 2010-2014 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. The Embedded Control Solutions Company and mTouch are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet, KleerNet logo, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2010-2014, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. ISBN: 978-1-63276-803-2 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2010-2014 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS20002230F-page 33 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2943-5100 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 Austin, TX Tel: 512-257-3370 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Canada - Toronto Tel: 905-673-0699 Fax: 905-673-6509 DS20002230F-page 34 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hangzhou Tel: 86-571-8792-8115 Fax: 86-571-8792-8116 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Dusseldorf Tel: 49-2129-3766400 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Germany - Pforzheim Tel: 49-7231-424750 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Italy - Venice Tel: 39-049-7625286 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Poland - Warsaw Tel: 48-22-3325737 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 03/25/14 2010-2014 Microchip Technology Inc.