A200RI/A300RI Series High Isolation, 2W & 3W Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: Parameter ● 2W & 3W Output Power Input Voltage Range ● Compact DIP Case ● 3,000 VDC Isolation ● Tight Line/Load Regulation Input Filter Reverse Polarity Input Current ● Single & Dual Outputs Short Circuit Input Power ● 17 Standard Models Output ● 800 kH MTBF Parameter ● Industry Standard Pin-Out Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) (Note 1) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Transient Recovery Time (Note 2) Transient Response Deviation Temperature Coefficient Output Short Circuit Conditions Min. 5 VDC Input 4.75 12 VDC Input 10.8 24 VDC Input 21.6 48 VDC Input 43.2 π (Pi) Filter Conditions Min. Dual Output , Balanced Loads Vin = Min to Max Iout = 10% to 100% Typ. 5.0 12.0 24.0 48.0 Typ. ±2.0 ±1.0 ±0.2 ±0.2 40 Over Line, Load & Temp. Max. 5.25 13.2 26.4 52.8 Units 0.5 2,500 A mW Max. ±4.0 ±3.0 ±0.3 ±0.5 50 75 5 Units % % % % mV P - P mV P - P mV rms % μSec % %/ºC 120 ±0.01 50 ±6.0 ±0.02 Typ. Max. 50 80 100 50% Load Step Change VDC Continuous General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 3,000 1,000 40 Units VDC MΩ pF kHz Environmental Parameter Operating Temperature Range MicroPower Direct 232 Tosca Drive Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Storage Temperature Range Cooling Humidity Conditions Min. Typ. -25 -25 -40 Free Air Convection RH, Non-condensing Max. +71 +90 +125 Units ºC ºC ºC 95 % Physical Case Size Case Material Weight 1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.42 Oz (12g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. 800 Typ. Max. Units kHours Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 7.5 15.0 30.0 55.0 260 3,000 Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec. All Models VDC ºC mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number Input Current (mA) Output Fuse Rating Reflected Efficiency Slow-Blow Current Ripple Voltage Current (%, Typ) (mA) (VDC) (mA, Max) (mA, Min) Full-Load No-Load Current Voltage (VDC) Nominal Range 5 5 5 5 5 12 12 12 12 12 24 24 24 24 24 48 48 4.75 - 5.25 4.75 - 5.25 4.75 - 5.25 4.75 - 5.25 4.75 - 5.25 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 43.2 - 52.8 43.2 - 52.8 (mA, Typ) A201RI A202RI A203RI A204RI A205RI A211RI A212RI A313RI A214RI A315RI A221RI A222RI A323RI A224RI A325RI A231RI A232RI Notes: 666 628 633 642 639 277 262 397 268 403 138 131 198 134 202 69 66 100 100 100 100 100 50 50 50 50 50 25 25 25 25 25 15 15 70 70 70 70 70 30 30 30 30 30 15 15 15 15 15 10 10 1. When measuring output ripple, it is recommended that an external 0.33 μF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. For noise sensitive applications, the use of 1.5 μF capacitors will reduce the output ripple. 2. Transient recovery is measured to within a 1% error band for a load step change of 50% to 100%. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. Dual output units may be connected to provide a 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR <1.0Ω at 100 kHz) capacitor be mounted close to the converter. For 5V input units a 2.2 μF is recommended, for 12V input units, a 1.0 μF; and for 24V & 48V units a 0.47 μF. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Pin Connections 5.0 12.0 15.0 ±12.0 ±15.0 5.0 12.0 15.0 ±12.0 ±15.0 5.0 12.0 15.0 ±12.0 ±15.0 5.0 12.0 400 165 133 ±83 ±66 400 165 200 ±83 ±100 400 165 200 ±83 ±100 400 165 0.0 0.0 0.0 ±0.0 ±0.0 0.0 0.0 0.0 ±0.0 ±0.0 0.0 0.0 0.0 ±0.0 ±0.0 0.0 0.0 60 63 63 62 62 60 63 63 62 62 60 63 63 62 62 60 63 1,000 1,000 1,000 1,000 1,000 750 750 750 750 750 350 350 350 350 350 135 135 Derating Curve Mechanical Dimensions Pin Single Dual 1, 2 10, 11 12 13 14 15 23, 24 +Vin NC -Vout +Vout NC NC -Vin +Vin Common NC -Vout NC +Vout -Vin NC: No Connection Capacitive Load Single Output Dual Output 470 μF Max ±220 μF Max Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Leads are tin plated for improved solderability. MicroPower Direct www.micropowerdirect.com 232 Tosca Drive Stoughton, MA 02072 ■ TEL: (781) 344-8226 ■ FAX: (781) 344-8481 ■ E-Mail: [email protected]