DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 Quad, Serial Input 14-Bit Multiplying Digital-to-Analog Converter FEATURES DESCRIPTION • • • The DAC8803 is a quad, 14-bit, current-output digital-to-analog converter (DAC) designed to operate from a single +2.7-V to 5-V supply. • • • • • • • • • • • Relative Accuracy: 1 LSB Max Differential Nonlinearity: 1 LSB Max 2-mA Full-Scale Current with VREF = ±10 V 0.5-µs Settling Time Midscale or Zero-Scale Reset Four Separate 4Q Multiplying Reference Inputs Reference Bandwidth: 10 MHz Reference Dynamics: -105 dB THD SPI™-Compatible 3-Wire Interface: 50-MHz Double Buffered Registers Enable Simultaneous Multichannel Update Internal Power-On Reset Compact SSOP-28 Package Industry-Standard Pin Configuration The applied external reference input voltage VREF determines the full-scale output current. An internal feedback resistor (RFB) provides temperature tracking for the full-scale output when combined with an external I-to-V precision amplifier. A doubled buffered serial data interface offers high-speed, 3-wire, SPI and microcontroller compatible inputs using serial data in (SDI), clock (CLK), and a chip select (CS). In addition, a serial data out pin (SDO) allows for daisy chaining when multiple packages are used. A common level-sensitive load DAC strobe (LDAC) input allows simultaneous update of all DAC outputs from previously loaded input registers. Additionally, an internal power-on reset forces the output voltage to zero at system turn on. An MSB pin allows system reset assertion (RS) to force all registers to zero code when MSB = 0, or to half-scale code when MSB = 1. APPLICATIONS • • • Automatic Test Equipment Instrumentation Digitally-Controlled Calibration The DAC8803 is packaged in an SSOP package. VREFA B C D D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 A0 A1 SDO SDI RFBA Input Register R DAC A Register R DAC A IOUTA AGNDA RFBB 14 Input Register R DAC B Register R DAC B IOUTC AGNDB RFBC Input Register R DAC C Register R DAC C IOUTC AGNDC CLK CS RFBD EN DAC A B C D 2:4 Decode DGND Input Register R DAC D Register R DAC D IOUTD AGNDD Power-On Reset RS MSB AGNDF LDAC Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. SPI is a trademark of Motorola, Inc. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005–2006, Texas Instruments Incorporated DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION (1) PRODUCT MINIMUM RELATIVE ACCURACY (LSB) DIFFERENTIAL NONLINEARITY (LSB) SPECIFIED TEMPERATURE RANGE PACKAGELEAD PACKAGE DESIGNATOR DAC8803 ±1 ±1 -40°C to +85°C SSOP-28 DB (1) ORDERING NUMBER TRANSPORT MEDIA QUANTITY DAC8803IDBT Tape and Reel, 250 DAC8803IDBR Tape and Reel, 2500 For the most current specifications and package information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com ABSOLUTE MAXIMUM RATINGS (1) DAC8803 UNIT VDD to GND -0.3 to +8 V VREF to GND -18 to +18 V Logic inputs and output to GND -0.3 to +8 V V(IOUT) to GND -0.3 to VDD + 0.3 V AGNDX to DGND -0.3 to +0.3 V ±50 mA (TJmax - TA)/θJA W Input current to any pin except supplies Package power dissipation Thermal resistance, θJA 100 °C/W Maximum junction temperature (TJmax) 150 °C Operating temperature range, Model A -40 to +85 °C Storage temperature range -65 to +150 °C (1) 2 28-Lead shrink surface-mount (RS-28) Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum conditions for extended periods may affect device reliability. Submit Documentation Feedback DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 ELECTRICAL CHARACTERISTICS VDD = +2.7 V to +5.5 V; IOUTX = Virtual GND, AGNDX = 0 V, VREFA, B, C, D = 10 V, TA = full operating temperature range, unless otherwise noted. DAC8803 PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT STATIC PERFORMANCE (1) Resolution Relative accuracy Differential nonlinearity DNL Output leakage current IOUTX Data = 0000h, TA = 25°C IOUTX Data = 0000h, TA = TA max Full-scale gain error GFSE Data = 3FFFh Full-scale tempco (2) TCVFS Feedback resistor RFBX ±0.75 14 Bits ±1 LSB ±1 LSB 10 nA 20 nA ±3 mV 1 ppm/°C VDD = 5 V kΩ REFERENCE INPUT VREFX Range VREFX -15 Input resistance RREFX 4 Input resistance match RREFX Input capacitance (2) CREFX Channel-to-channel 5 15 V 6 kΩ 1 % 5 pF ANALOG OUTPUT Output current Output capacitance (2) IOUTX Data = 3FFFh COUTX Code-dependent 1.6 2.5 50 mA pF LOGIC INPUTS AND OUTPUT Input low voltage Input high voltage VIL VDD = +2.7 V 0.6 V VIL VDD = +5 V 0.8 V VIH VDD = +2.7 V 2.1 V VIH VDD = +5 V 2.4 V Input leakage current IIL 1 µA Input capacitance (2) CIL 10 pF 0.4 V Logic output low voltage VOL IOL = 1.6 mA Logic output high voltage VOH IOH = 100 µA 4 V tCH 25 ns INTERFACE TIMING (2), (3) Clock width high Clock width low tCL 25 ns CS to Clock setup tCSS 0 ns Clock to CS hold tCSH 25 tPD 2 Clock to SDO prop delay Load DAC pulsewidth ns 20 ns tLDAC 25 ns Data setup tDS 20 ns Data hold tDH 20 ns Load setup tLDS 5 ns Load hold tLDH 25 ns (1) (2) (3) All static performance tests (except IOUT) are performed in a closed-loop system using an external precision OPA277 I-to-V converter amplifier. The DAC8803 RFB terminal is tied to the amplifier output. Typical values represent average readings measured at 25°C. These parameters are specified by design and not subject to production testing. All input control signals are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed from a voltage level of 1.5 V. Submit Documentation Feedback 3 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 ELECTRICAL CHARACTERISTICS (continued) VDD = +2.7 V to +5.5 V; IOUTX = Virtual GND, AGNDX = 0 V, VREFA, B, C, D = 10 V, TA = full operating temperature range, unless otherwise noted. DAC8803 PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT SUPPLY CHARACTERISTICS Power supply range Positive supply current Power dissipation Power supply sensitivity VDD 2.7 5.5 V 2 5 µA 1 2.5 µA Logic inputs = 0 V 0.025 mW ∆VDD = ±5% 0.006 % RANGE IDD Logic inputs = 0 V, VDD = +4.5 V to +5.5 V IDD Logic inputs = 0 V, VDD = +2.7 V to +3.6 V PDISS PSS AC CHARACTERISTICS (4) Output voltage settling time Reference multiplying BW DAC glitch impulse Feedthrough error Crosstalk error Digital feedthrough Total harmonic distortion Output spot noise voltage (4) 4 ts To ±0.1% of full-scale, Data = 0000h to 3FFFh to 0000h 0.3 µs ts To ±0.006% of full-scale, Data = 0000h to 3FFFh to 0000h 0.5 µs VREFX = 100 mVRMS, Data = 3FFFh, CFB = 3 pF 10 MHz nV/s BW -3 dB Q VREFX = 10 V, Data = 1FFFh to 2000h to 1FFFh 1 VOUTX/VREFX Data = 0000h, VREFX = 100 mVRMS, f = 100 kHz -70 dB VOUTA/VREFB Data = 0000h, VREFB = 100 mVRMS, Adjacent channel, f = 100 kHz -100 dB Q THD en CS = 1 and fCLK = 1 MHz VREF = 5 VPP, Data = 3FFFh, f = 1 kHz 1 -105 f = 1 kHz, BW = 1 Hz All ac characteristic tests are performed in a closed-loop system using a THS4011 I-to-V converter amplifier. Submit Documentation Feedback 12 nV/s dB nV/√Hz DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 PIN CONFIGURATIONS DAC8803 (TOP VIEW) AGNDA IOUTA VREFA RFBA MSB RS VDD CS CLK SDI RFBB VREFB IOUTB AGNDB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 AGNDD IOUTD VREFD RFBD DGND VSS(1) AGNDF LDAC SDO (1) NC RFBC VREFC IOUTC AGNDC Note (1): No internal connection PIN DESCRIPTION PIN NAME 1, 14, 15, 28 AGNDA, AGNDB, AGNDC, AGNDD DAC A, B, C, D Analog ground DESCRIPTION 2, 13, 16, 27 IOUTA, IOUTB, IOUTC, IOUTD DAC A, B, C, D Current output 3, 12, 17, 26 VREFA, VREFB, VREFC, VREFD DAC A, B, C, D Reference voltage input terminal. Establishes DAC A, B, C, D full-scale output voltage. Can be tied to VDD. 4, 11, 18, 25 RFBA, RFBB, RFBC, RFBD, Establish voltage output for DAC A, B, C, D by connecting to external amplifier output. 5 MSB MSB Bit set during a reset pulse (RS) or at system power-on if tied to ground or VDD. 6 RS Reset pin, active low. Input register and DAC registers are set to all zeros or half-scale code (2000h) determined by the voltage on the MSB pin. Register data = 2000h when MSB = 1. 7 VDD Positive power-supply input. Specified range of operation +2.7 V to +5.5 V. 8 CS Chip select; active low input. Disables shift register loading when high. Transfers shift register data to input register when CS/LDAC goes high. Does not affect LDAC operation. 9 CLK Clock input; positive edge triggered clocks data into shift register 10 SDI Serial data input; data loads directly into the shift register. 19 NC Not connected; leave floating 20 SDO Serial data output; input data load directly into shift register. Data appears at SDO, 17 clock pulses after input at the SDI pin. 21 LDAC Load DAC register strobe; level sensitive active low. Transfers all input register data to the DAC registers. Asynchronous active low input. See Table 1 for operation. 22 AGNDF High current analog force ground. 23 VSS 24 DGND No internal connection. Digital ground. Submit Documentation Feedback 5 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +5 V At TA = +25°C, +VDD = +5 V, unless otherwise noted. Channel A LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25C 0.8 TA = +25C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 2. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = −40 C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) Figure 1. TA = −40 C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 4. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 3. TA = +85C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 Digital Input Code Figure 5. 6 6144 8192 10240 12288 14336 16383 Digital Input Code 2048 4096 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 6. Submit Documentation Feedback DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +5 V (continued) At TA = +25°C, +VDD = +5 V, unless otherwise noted. Channel B LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25C 0.8 TA = +25C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 8. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = −40 C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) Figure 7. TA = −40 C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 9. Figure 10. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85C 0.8 TA = +85C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 6144 8192 10240 12288 14336 16383 Digital Input Code 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 Digital Input Code Figure 11. 2048 4096 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 12. Submit Documentation Feedback 7 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +5 V (continued) At TA = +25°C, +VDD = +5 V, unless otherwise noted. Channel C LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25C 0.8 TA = +25C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 14. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = −40 C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) Figure 13. TA = −40C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 16. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 15. TA = +85C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 Digital Input Code Figure 17. 8 6144 8192 10240 12288 14336 16383 Digital Input Code 2048 4096 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 18. Submit Documentation Feedback DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +5 V (continued) At TA = +25°C, +VDD = +5 V, unless otherwise noted. Channel D LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25C 0.8 TA = +25C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 1.0 LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = −40 C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) Figure 20. 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 21. Figure 22. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85C 0.8 TA = +85C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 8192 10240 12288 14336 16383 Figure 19. TA = −40 C 0.8 6144 Digital Input Code Digital Input Code 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 Digital Input Code Figure 23. 2048 4096 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 24. Submit Documentation Feedback 9 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +5 V (continued) At TA = +25°C, +VDD = +5 V, unless otherwise noted. SUPPLY CURRENT vs LOGIC INPUT VOLTAGE REFERENCE MULTIPLYING BANDWIDTH 180 VDD = +5.0V 140 120 6 0 −6 − 12 − 18 − 24 − 30 − 36 − 42 − 48 − 54 − 60 − 66 − 72 − 78 − 84 − 90 − 96 − 102 − 108 − 114 1 0 0x3FFF 0x2000 0x1000 0x0800 0x0400 0x0200 0x0100 0x0080 0x0040 0x0020 0x0010 0x0008 0x0004 0x0002 0x0001 A ttenu ation (dB) Supply Current, IDD (µA) 160 100 80 60 40 VDD = +2.7V 20 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Logic Input Voltage (V) 0x0000 1 00 1k 10k 10 0k 1M 10M 100 M B and w idth (H z) Figure 26. DAC GLITCH DAC SETTLING TIME Voltage Output Settling Output Voltage (5V/div) Output Voltage (50mV/div) Figure 25. Code: 1FFFh to 2000h Trigger Pulse LDAC Pulse Time (0.1µs/div) Time (0.2µs/div) Figure 27. Figure 28. IDD vs TEMPERATURE ENDPOINT ERROR vs TEMPERATURE 5.0 3 4.5 2 Endpoint Error (mV) 4.0 IDD (µA) 3.5 3.0 5.0V 2.5 2.0 1.5 1.0 0 −40 0 DAC A −1 DAC D −3 −20 0 20 40 60 80 100 −40 Temperature (C) Figure 29. 10 DAC B −2 2.7V 0.5 DAC C 1 −20 0 20 40 Temperature ( C) Figure 30. Submit Documentation Feedback 60 80 100 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +2.7 V At TA = +25°C, +VDD = +2.7 V, unless otherwise noted. Channel A LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25C 0.8 TA = +25C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 32. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = −40C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) Figure 31. TA = −40 C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 33. Figure 34. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85C 0.8 TA = +85C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 6144 8192 10240 12288 14336 16383 Digital Input Code 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 Digital Input Code Figure 35. 2048 4096 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 36. Submit Documentation Feedback 11 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued) At TA = +25°C, +VDD = +2.7 V, unless otherwise noted. Channel B LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25C 0.8 TA = +25C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 38. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = −40C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) Figure 37. TA = −40C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 40. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 39. TA = +85C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 Digital Input Code Figure 41. 12 6144 8192 10240 12288 14336 16383 Digital Input Code 2048 4096 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 42. Submit Documentation Feedback DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued) At TA = +25°C, +VDD = +2.7 V, unless otherwise noted. Channel C LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25C 0.8 TA = +25C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 44. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = −40 C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) Figure 43. TA = −40C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 45. Figure 46. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85C 0.8 TA = +85C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 6144 8192 10240 12288 14336 16383 Digital Input Code 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 Digital Input Code Figure 47. 2048 4096 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 48. Submit Documentation Feedback 13 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued) At TA = +25°C, +VDD = +2.7 V, unless otherwise noted. Channel D LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 1.0 TA = +25C 0.8 TA = +25C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 0 8192 10240 12288 14336 16383 2048 4096 Digital Input Code 1.0 Figure 50. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = −40 C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) Figure 49. TA = −40 C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 2048 4096 Digital Input Code 1.0 Figure 52. LINEARITY ERROR vs DIGITAL INPUT CODE DIFFERENTIAL LINEARITY ERROR vs DIGITAL INPUT CODE 1.0 TA = +85C 0.8 0.6 0.6 0.4 0.4 DNL (LSB) INL (LSB) 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 51. TA = +85C 0.8 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 0 2048 4096 6144 8192 10240 12288 14336 16383 0 Digital Input Code Figure 53. 14 6144 8192 10240 12288 14336 16383 Digital Input Code 2048 4096 6144 8192 10240 12288 14336 16383 Digital Input Code Figure 54. Submit Documentation Feedback DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued) At TA = +25°C, +VDD = +2.7 V, unless otherwise noted. DAC GLITCH ENDPOINT ERROR vs TEMPERATURE 3 Endpoint Error (mV) Output Voltage (50mV/div) 2 Code: 1FFFh to 2000h DAC C DAC B 1 0 DAC A −1 DAC D −2 LDAC Pulse −3 −40 Time (0.2µs/div) −20 0 Figure 55. 20 40 Temperature ( C) 60 80 100 Figure 56. TIMING INFORMATION SDI A1 A0 D13 D12 D11 D10 D9 D8 D7 D6 D1 D0 CLK Input REG. LD tCSS CS tds tdh tch tcsh tcl tlds LDAC tpd SDO tLDH tLDAC Figure 57. DAC8803 Timing Diagram Submit Documentation Feedback 15 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 THEORY OF OPERATION CIRCUIT OPERATION The DAC8803 contains four, 14-bit, current-output, digital-to-analog converters (DACs) respectively. Each DAC has its own independent multiplying reference input. The DAC8803 uses a 3-wire SPI-compatible serial data interface, with a configurable asynchronous RS pin for half-scale (MSB = 1) or zero-scale (MSB = 0) preset. In addition, an LDAC strobe enables four channel simultaneous updates for hardware synchronized output voltage changes. D/A Converter The DAC8803 contains four current-steering R-2R ladder DACs. Figure 58 shows a typical equivalent DAC. Each DAC contains a matching feedback resistor for use with an external I-to-V converter amplifier. The RFBX pin is connected to the output of the external amplifier. The IOUTX terminal is connected to the inverting input of the external amplifier. The AGNDX pin should be Kelvin-connected to the load point in the circuit requiring the full 14-bit accuracy. The DAC is designed to operate with both negative or positive reference voltages. The VDD power pin is only used by the logic to drive the DAC switches on and off. Note that a matching switch is used in series with the internal 5 kΩ feedback resistor. If users are attempting to measure the value of RFB, power must be applied to VDD in order to achieve continuity. The DAC output voltage is determined by VREF and the digital data (D) according to Equation 1: V OUT VREF D 16384 (1) Note that the output polarity is opposite to the VREF polarity for dc reference voltages. R R VDD R RFBX VREFX 2R 2R 2R 5 kW R S2 S1 IOUTX AGNDF AGNDX From other DACs AGND DGND Digital interface connections omitted for clarity. Switches S1 and S2 are closed. VDD must be powered. Figure 58. Typical Equivalent DAC Channel The DAC is also designed to accommodate ac reference input signals. The DAC8803 accommodates input reference voltages in the range of -15 V to +15 V. The reference voltage inputs exhibit a constant nominal input resistance of 5 kΩ, ±20%. On the other hand, the DAC outputs IOUTA, B, C, D are code-dependent and produce various output resistances and capacitances. The choice of external amplifier should take into account the variation in impedance generated by the DAC8803 on the amplifiers' inverting input node. The feedback resistance, in parallel with the DAC ladder resistance, dominates output voltage noise. For multiplying mode applications, an external feedback compensation capacitor (CFB) may be needed to provide a critically damped output response for step changes in reference input voltages. 16 Submit Documentation Feedback DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 Figure 26 shows the gain versus frequency performance at various attenuation settings using a 3 pF external feedback capacitor connected across the IOUTX and RFBX terminals. In order to maintain good analog performance, power supply bypassing of 0.01 µF, in parallel with 1 µF, is recommended. Under these conditions, clean power supply with low ripple voltage capability should be used. Switching power supplies are usually not suitable for this application because of the higher ripple voltage and PSS frequency-dependent characteristics. It is best to derive the DAC8803 5-V supply from the system analog supply voltages. (Do not use the digital 5-V supply.) See Figure 59. 15 V 2R Analog Power Supply 5V R VDD R R R RFBX VREFX 2R 2R 2R 5 kW R 15 V S2 S1 IOUTX AGNDF AGNDX From other DACs AGND VCC A1 VOUT VEE Load DGND Digital interface connections omitted for clarity. Switches S1 and S2 are closed. VDD must be powered. Figure 59. Recommended Kelvin-Sensed Hookup Submit Documentation Feedback 17 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 VREF A B C D CS EN VDD CLK SDI SDO D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 A0 A1 14 RFBA DAC A Register R Input Register R DAC A IOUTA AGNDA RFBB DAC B Register R Input Register R DAC B DAC A B C D 2:4 Decode IOUTC AGNDB RFBC DAC C Register R Input Register R DAC C IOUTC AGNDC RFBD DAC D Register R Input Register R DAC D IOUTD AGNDD Set MSB Set MSB PowerOn Reset DGND AGNDF MSB LDAC RS Figure 60. System Level Digital Interfacing SERIAL DATA INTERFACE The DAC8803 uses a 3-wire (CS, SDI, CLK) SPI-compatible serial data interface. Serial data of the DAC8803 is clocked into the serial input register in a 16-bit data-word format. MSB bits are loaded first. Table 2 defines the 16 data-word bits for the DAC8803. Data is placed on the SDI pin, and clocked into the register on the positive clock edge of CLK subject to the data setup and data hold time requirements specified in the Interface Timing Specifications. Data can only be clocked in while the CS chip select pin is active low. For the DAC8803, only the last 16 bits clocked into the serial register are interrogated when the CS pin returns to the logic high state. Since most microcontrollers output serial data in 8-bit bytes, two right-justified data bytes can be written to the DAC8803. Keeping the CS line low between the first and second byte transfers results in a successful serial register update. 18 Submit Documentation Feedback DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 Once the data is properly aligned in the shift register, the positive edge of the CS initiates the transfer of new data to the target DAC register, determined by the decoding of address bits A1and A0. For the DAC8803, Table 2 and Table 3 define the characteristics of the software serial interface. Figure 61 shows the equivalent logic interface for the key digital control pins for the DAC8803. To Input Register A B C D Address Decoder CS EN CLK Shift Register SDI 17th Clock SDO Figure 61. DAC8803 Equivalent Logic Interface Two additional pins RS and MSB provide hardware control over the preset function and DAC register loading. If these functions are not needed, the RS pin can be tied to logic high. The asynchronous input RS pin forces all input and DAC registers to either the zero-code state (MSB = 0), or the half-scale state (MSB = 1). POWER ON RESET When the VDD power supply is turned on, an internal reset strobe forces all the Input and DAC registers to the zero-code state or half-scale, depending on the MSB pin voltage. The VDD power supply should have a smooth positive ramp without drooping in order to have consistent results, especially in the region of VDD = 1.5 V to 2.3 V. The DAC register data stays at zero or half-scale setting until a valid serial register data load takes place. ESD Protection Circuits All logic-input pins contain back-biased ESD protection zener diodes connected to ground (DGND) and VDD as shown in Figure 62. VDD Digital Inputs 250 W DGND Figure 62. Equivalent ESD Protection Circuits Submit Documentation Feedback 19 DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 PCB LAYOUT The DAC8803 is a high-accuracy DAC that can have its performance compromised by grounding and printed circuit board (PCB) lead trace resistance. The 14-bit DAC8803 with a 10-V full-scale range has an LSB value of 610 µV. The ladder and associated reference and analog ground currents for a given channel can be as high as 2 mA. With this 2 mA current level, a series wiring and connector resistance of only 305 mΩ will cause 1 LSB of voltage drop. The preferred PCB layout for the DAC8803 is to have all AGNDX pins connected directly to an analog ground plane at the unit. The non-inverting input of each channel I/V converter should also either connect directly to the analog ground plane or have an individual sense trace back to the AGNDX pin connection. The feedback resistor trace to the I/V converter should also be kept short and low resistance to prevent IR drops from contributing to gain error. This attention to wiring ensures the optimal performance of the DAC8803. Table 1. Control Logic Truth Table (1) CS CLK LDAC RS MSB H X H H X No effect Latched Latched L L H H X No effect Latched Latched L ↑+ H H X Shift register data advanced one bit Latched Latched L H H H X No effect Latched Latched INPUT REGISTER DAC REGISTER Latched H H X No effect Selected DAC updated with current SR contents X L H X No effect Latched Transparent X H H X No effect Latched Latched H X ↑+ H X No effect Latched Latched H X H L 0 No effect Latched data = 0000h Latched data = 0000h H X H L H No effect Latched data = 2000h Latched data = 2000h ↑+ L H H (1) SERIAL SHIFT REGISTER ↑+ Positive logic transition; X = Do not care Table 2. Serial Input Register Data Format, Data Loaded MSB First (1) Bit B15 (MSB) B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 (LSB) Data A1 A0 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 (1) Only the last 16 bits of data clocked into the serial register (address + data) are inspected when the CS line positive edge returns to logic high. At this point an internally generated load strobe transfers the serial register data contents (bits D13-D0) to the decoded DAC-input-register address determined by bits A1 and A0. Any extra bits clocked into the DAC8803 shift register are ignored; only the last 16 bits clocked in are used. If double-buffered data is not needed, the LDAC pin can be tied logic low to disable the DAC registers. Table 3. Address Decode 20 A1 A0 DAC DECODE 0 0 DAC A 0 1 DAC B 1 0 DAC C 1 1 DAC D Submit Documentation Feedback DAC8803 www.ti.com SBAS340C – JANUARY 2005 – REVISED FEBRUARY 2006 APPLICATION INFORMATION The DAC8803, a 2-quadrant multiplying DAC, can be used to generate a unipolar output. The polarity of the full-scale output IOUT is the inverse of the input reference voltage at VREF. Some applications require full 4-quadrant multiplying capabilities or bipolar output swing, as shown in Figure 63. An additional external op amp A2 is added as a summing amp. In this circuit the first and second amps (A1 and A2) provide a gain of 2X that widens the output span to 20 V. A 4-quadrant multiplying circuit is implemented by using a 10-V offset of the reference voltage to bias A2. According to the following circuit transfer equation (Equation 2), input data (D) from code 0 to full scale produces output voltages of VOUT = -10 V to VOUT = 10 V. V OUT D 1 V 8192 REF (2) 10 kW 10 V 5 kW 10 kW A2 OPA277 VOUT VREF -10 V < VOUT < +10 V VDD VREFX RFBX IOUTX One Channel DAC8803 AGNDF A1 OPA277 AGNDX Digital interface connections omitted for clarity. Figure 63. Four-Quadrant Multiplying Application Circuit Cross-Reference The DAC8803 has an industry-standard pinout. Table 4 provides the cross-reference information. Table 4. Cross-Reference PRODUCT INL (LSB) DNL (LSB) SPECIFIED TEMPERATURE RANGE DAC8803IDB ±1 ±1 -40°C to +85°C PACKAGE DESCRIPTION PACKAGE OPTION CROSSREFERENCE PART 28-Lead MicroSOIC SSOP-28 AD5554BRS Submit Documentation Feedback 21 PACKAGE OPTION ADDENDUM www.ti.com 26-Jun-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty DAC8803IDBR ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR DAC8803IDBRG4 ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR DAC8803IDBT ACTIVE SSOP DB 28 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR DAC8803IDBTG4 ACTIVE SSOP DB 28 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 30-Jan-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DAC8803IDBR SSOP DB 28 2000 330.0 16.4 8.1 10.4 2.5 12.0 16.0 Q1 DAC8803IDBT SSOP DB 28 250 330.0 16.4 8.1 10.4 2.5 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 30-Jan-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DAC8803IDBR SSOP DB 28 2000 346.0 346.0 33.0 DAC8803IDBT SSOP DB 28 250 346.0 346.0 33.0 Pack Materials-Page 2 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP® Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2009, Texas Instruments Incorporated